0.85-PW, 33-fs Ti:sapphire laser

We have successfully produced a laser pulse with a peak power of 0.85 PW for a pulse duration of 33 fs in a four-stage Ti:sapphire amplifier chain based on chirped-pulse amplification. To our knowledge this result represents the highest peak power pulses yet produced in any Ti:sapphire chirped-pulse amplification system.     

High-power parametric amplification of 11.8-fs laser pulses with carrier-envelope phase control

Phase-stable parametric chirped-pulse amplification of ultrashort pulses from a carrier-envelope phase-stabilized mode-locked Ti:sapphire oscillator (11.0 fs) to 0.25 mJ/pulse at 1 kHz is demonstrated. Compression with a grating compressor and a LCD shaper yields near-Fourier-limited 11.8-fs pulses with an energy of 0.12 mJ. The amplifier is pumped by 532-nm pulses from a synchronized mode-locked laser, Nd:YAG amplifier system. This approach is shown to be promising for the next generation of ultrafast amplifiers aimed at producing terawatt-level phase-controlled few-cycle laser pulses.     

Sub-picosecond pulses at 100 W average power from a Yb:YLF chirped-pulse amplification system

We present a high-repetition-frequency, diode-pumped, and chirped-pulse amplification system operating at 106 W average output power with excellent beam quality (M(2)=1.3), based on cryogenically cooled Yb:YLF. 1 nJ seed pulses, derived from a mode-locked Ti:sapphire laser, are first amplified to 1 mJ pulse energy at 10 kHz repetition frequency in a regenerative amplifier. The second-stage, multipass amplifier increases the pulse energy to 10.6 mJ, resulting in a spectral width of 2.2 nm. The pulses are compressed to 865 fs in duration, which is 1.26 times the transform limit.     

1.5 mJ, 6.4 fs parametric chirped-pulse amplification system at 1 kHz

We demonstrate an optical parametric chirped-pulse amplification (OPCPA) system with the pulse energy of 1.5 mJ at a 1 kHz repetition rate. The newly developed 100 ps Ti:sapphire pump laser system, which was optically synchronized with OPCPA seed pulses, delivered 10 mJ, 400 nm pump pulses. After three-stage parametric amplification, recompression of the amplifier output from 45 ps to 6.4 fs was performed. The pulse width of 6.4 fs is, to our knowledge, the shortest ever obtained by OPCPA, and the average power of 1.5 W (1.5 mJ, 1 kHz) is believed to be the highest among few-cycle OPCPA systems.     

High-average-power kilohertz-repetition-rate sub-100-fs Ti:sapphire amplifier system

We report on a femtosecond Ti:sapphire laser amplifier system that generates pulse energies >5 mJ at a 1-kHz repetition rate. The system consists of regenerative and multipass amplifiers and uses the technique of chirped-pulse amplification. When the system was seeded with 70-fs pulses at 800 nm from a self-mode-locked Ti:sapphire oscillator, amplified pulses of 94-fs duration at a repetition rate of 1 kHz and an average output power of 5.4 W were produced. The amplified pulse-repetition rate is variable from 250 Hz to 3 kHz. Pulse energies of >7.5 mJ were obtained at 500 and 250 Hz.     

Development of ultra-short pulse VUV laser system for nanoscale processing

We have developed intense vacuum ultraviolet (VUV) radiation sources for advanced material processing, such as photochemical surface reactions and precise processing on a nanometer scale. We have constructed a new VUV laser system to generate sub-picosecond pulses at the wavelength of 126 nm. A seed VUV pulse was generated in Xe as the 7th harmonic of a 882-nm Ti:sapphire laser. The optimum conversion was achieved at the pressure of 1.2 Torr. The seed pulse will be amplified by the Ar₂^*\mathrm{Ar}_{2}^{*} media generated by an optical-field-induced ionization Ar plasma produced by the Ti:sapphire laser. We have obtained a gain coefficient of g=0.16 cm⁻¹. Our developing system will provide VUV ultra-short pulses with sub-μJ energy at a repetition rate of 1 kHz.     

用钛宝石再生放大器产生高重复率啁啾脉冲列

针对啁啾脉冲放大技术建成的钛宝石激光装置，提出一种获得高重复率激光脉冲列的方法.通过改变钛宝石再生放大器中泡克耳斯盒电光开关的传统工作模式，使得腔内放大的脉冲从某特定时刻起，每当在腔内往返一次就以一定的倒出比例（倒出率）倒出腔内脉冲能量的一部分，从而可以在有限的时间段内产生高重复率的啁啾激光脉冲列.基于Franz-Nodvik放大理论，建立了该高重复率再生放大器的理论模型，通过数值计算，系统地分析了初始增益、倒出时刻、倒出率对输出的脉冲序列的影响.在抽运功率为35mJ、倒出率为1/2的实验条件下，通过腔外的脉冲数量选择器，在一个抽运周期内的有限时间段内已获得了14个幅度相近、单脉冲能量约为0.02mJ、重复率为100MHz的啁啾脉冲序列.从此啁啾脉冲列中选取数个脉冲，通过10TW级的激光系统放大和压缩，已获得100MHz重复率的飞秒太瓦级脉冲列. 关键词： 高重复率 多通放大 啁啾脉冲放大 钛宝石激光器     

12-fs pulses from a continuous-wave-pumped 200-nJ Ti:sapphire amplifier at a variable repetition rate as high as 4 MHz

We demonstrate a novel compact femtosecond Ti:sapphire laser system operating at repetition rates from 10 kHz to 4 MHz. The scheme is based on the combination of a broadband cavity-dumped oscillator and a double-pass Ti:sapphire amplifier pumped by a low-noise cw solid-state laser. Amplified pulses with an extremely smooth spectrum, a duration of only 12 fs, and less than 0.25% rms fluctuation are generated in a beam with M2 < 1.2. A maximum pulse energy of 210 nJ and an average output power of as much as 720 mW are achieved. This output energy is sufficient to generate a stable continuum in a sapphire disk.     

输出能量4mJ的1kHz飞秒掺钛蓝宝石激光再生放大研究

针对高能量千赫兹重复频率飞秒激光的应用需求,设计了一套采用线性再生腔结构的高效率飞秒钛宝石激光啁啾脉冲放大系统.通过优化腔型设计,在重复频率为1 kHz、单脉冲能量为20 mJ的527 nm激光抽运下,将展宽后的800 nm啁啾脉冲激光的能量放大到5.8 mJ,对应斜效率达到30.7%.进一步通过色散补偿压缩脉冲宽度,获得了单脉冲能量为4 mJ、脉冲宽度为45.7 fs的输出,稳定性测量表明激光的能量抖动仅为0.18%(均方根值).     

0.2-TW laser system at 1kHz

We have developed a 1-kHz repetition-rate Ti:sapphire laser system that can simultaneously generate high peak and average powers of 0.2TW and 4W, respectively. The laser system generates 4-mJ energy pulses with a 20-fs pulse width. We eliminated thermal lensing in the system by cooling the Ti:sapphire crystal to 125K. The output 20-fs pulses were fully characterized by use of the new technique of transient-grating frequency-resolved optical gating. We demonstrate experimentally that the pulse duration at the output is limited only by fifth-order dispersion.     

11-W average power Ti:sapphire amplifier system using downchirped pulse amplification

We demonstrate a high-power laser system that employs a new scheme in which pulses with negative chirp are amplified and then recompressed by dispersion in a block of transparent material. This scheme has significant advantages for amplification of intermediate energy pulses at high average power, including insensitivity to small misalignments of the pulse compressor, elimination of compressor gratings and their thermal loading issues, low compressor energy and bandwidth throughput losses, and a simplified optical design. Using this scheme, we demonstrate what we believe is the highest-average-power single-stage Ti:sapphire amplifier system with 11-W compressed output.     

Generation of high-contrast and high-intensity laser pulses using an OPCPA preamplifier in a double CPA, Ti:sapphire laser system

We demonstrate a high-contrast, high-intensity double chirped-pulse amplification (CPA) Ti:sapphire laser system using an optical parametric chirped-pulse (OPCPA) pre- amplifier. By injecting cleaned microjoule seed pulses into the OPCPA, a temporal contrast greater than 10¹⁰ within picosecond times before the main femtosecond pulse is demonstrated with an output pulse energy of 1.7 J and a pulse duration of 30 fs, corresponding to a peak power of 60 TW at a 10 Hz repetition rate. This system uses a cryogenically-cooled Ti:sapphire final amplifier and generates focused peak intensities in excess of 10²⁰ W/cm².     

A compact Ti:sapphire femtosecond pulse amplifier without stretcher at high repetition rate

We report a simple approach to amplify Ti:sapphire femtosecond pulses to moderate energy levels by achirped regenerative amplifier. The seed pulses are broaden naturally because of the material dispersionof system components in regenerative cavity. The off-focusing Ti:sapphire crystal avoids effectively theoptical damage. It sustains amplification over a wavelength range from 775 nm to more than 810 nmwith a birefringent filter and an oscillation bandwidth of 7.7 nm, and produces 2.1 ps chirped outputpulse energy of 100μJ at 1.1-mJ pumping energy. This system shows good performances in stability andefficiency with the benefits of two thin-film polarizers and TEM00 mode pumping laser.     

基于交叉偏振波产生的脉冲净化技术研究与应用

本文利用交叉偏振波产生技术(XPW)对800 nm波段钛宝石飞秒激光器输出的激光脉冲进行时域净化, 提高脉冲时域对比度, 并测量验证了10¹¹对比度的脉冲, 达到测量仪器的动态范围极限, 比初始脉冲时域对比度有三个量级的提高, XPW的效率为22%. 同时发现净化后脉冲光谱宽度也得到一定展宽, 进一步利用啁啾镜对和补偿片对净化后的脉冲进行色散补偿, 得到25 fs脉宽的脉冲. 利用该净化后的激光脉冲作为种子注入已有的太瓦级钛宝石啁啾脉冲放大系统中, 在输出脉冲能量250 mJ, 宽度50 fs, 对应峰值功率5 TW的情况下, 在主脉冲前100 ps以外的范围内测量验证了10¹¹的脉冲对比度.     

Compact, high-throughput expansion-compression scheme for chirped pulse amplification in the 10 fs range

A novel pulse stretching-compression system suitable for kHz-rate chirped-pulse amplification of ≈10 fs pulses in Ti:sapphire systems is demonstrated. The material dispersion of the system components used for pulse selection and isolation broadens the wide-band seed pulses by a factor of ≈300, allowing amplification up to the submillijoule energy range. The compressor consists of a pair of prisms and newly-developed chirped multilayer dielectric mirrors for compensating high order dispersion. Using this simple scheme a recompression of unamplified pulses down to 15 fs with a throughput as high as 80% is demonstrated.     

双色场下紫外超短脉冲的频谱展宽

当共线传输的双色强激光脉冲满足时间重叠时,其等离子体通道间将出现强烈的耦合作用,由此引起的交叉相位调制可产生强烈的非线性效应,使紫外超短脉冲的频谱展宽效应得到增强.将由钛宝石激光系统经三倍频得到的能量为045 mJ、带宽为15 nm的紫外脉冲和能量为71 mJ的近红外脉冲共线聚焦后,在氩气样品池中分别诱导产生等离子体通道,发现紫外脉冲光谱受到明显调制.调制后的光谱半高全宽增至64 nm,为聚焦前谱宽的4倍,是单束紫外脉冲成丝时谱宽的25倍.实验着重研究在不同时间延迟、耦合位置和气体压强情况下,双 关键词： 紫外超快脉冲 双色光丝 非线性效应 光谱展宽     

基于大基模体积的10mJ飞秒钛宝石激光再生放大器

文章报导了基于大基模体积的高能量飞秒钛宝石激光再生放大器的设计与实验研究,在重复频率10 Hz、抽运能量60 mJ的激励下,得到了单脉冲能量17.4 mJ的种子脉冲放大结果,压缩后的脉冲宽度为40.6 fs,能量为13.9 mJ.借助于此大基模体积再生腔,仅增加一级多通放大,实现了峰值功率达1.9 TW飞秒激光脉冲输出.结果表明,大模体积再生放大不仅降低了后续放大对抽运能量的要求,也可以单独压缩实现再生腔直接输出10 mJ量级的飞秒激光脉冲,是大能量高峰值功率飞秒激光系统的优质前端.     

Temporal characteristics of Ti: sapphire laser pumped synchronously by bounded pulse train

A Ti: sapphire laser pumped synchronously by a bounded frequency-doubled pulse train of a pulsed mode-locked Nd : YAG laser was presented. The temporal characteristics of the laser and optimal conditions of generating stable ultrashort pulses are also given.     

空气中激光等离子体通道的三次谐波光谱特性研究

对不同条件下强激光在空气中形成等离子体通道的三次谐波光谱特性进行了研究。单脉冲能量12 mJ,脉宽30 fs,重复频率10 Hz,中心波长795 nm的飞秒激光脉冲经0.5 m焦距的凹面镜聚焦,在空气中形成了等离子体通道, 并在前 向观测到谱线半峰全宽（FWHM）为15 nm的三次谐波。随着脉冲啁啾的变化,三次谐波的光谱出现红移或兰移,当激光脉冲附带+1.3×105fs2的二阶色散时,三次谐波谱线红移且谱峰强度增长了两倍。同时 ,通过改变可编程声光色散滤波器（AOPDF）光谱调制的位置（Hole position）,三次谐波的光谱也发生频移。