Employing electrochemical frequency modulation for studying corrosion and corrosion inhibition of copper in sodium chloride solutions

The inhibition effect of 2-carboxymethylthio-4-(p-methoxyphenyl)-6-oxo-1,6-dihy-dropyrimidine-5-carbonitrile (CPD) towards the corrosion of copper was studied in aerated stagnant 3.5% NaCl at 25 °C using ac techniques include electrochemical frequency modulation and electrochemical impedance spectroscopy as well as potentiodynamic polarization measurements. Corrosion rates determined using electrochemical frequency modulation (EFM) which measures the non-linear behaviour of a corroding system are compared with corrosion rates obtained from traditional electrochemical techniques and show good agreement. Data obtained from EIS were analyzed to model the corrosion inhibition process through equivalent circuit. Polarization measurements showed that CPD acts as mixed-type inhibitor. The inhibition efficiency increases with an increase in the concentration of CPD. The adsorption of the inhibitor on the copper surface in the sodium chloride solution was found to obey Langmuir’s adsorption isotherm. A mixed inhibition mechanism is proposed for the inhibitive effects of CPD as revealed by potentiodynamic polarization technique.     

The Application of Microelectrodes for the Measurements of Trace Metals in Water

Abstract

The analytical approaches for the determination of trace concentrations of heavy metals in aquatic systems are briefly introduced. A detailed review on the recent advances of microelectrodes is presented, including the definitions, types, advantages, theory, and fabrication of microelectrodes. The application of microelectrodes on the measurements of trace metals in water is focused on the voltammetric‐, potentiometric‐, and in situ electrochemical sensors.     

Aqueous extract of Acacia cyanophylla leaves as environmentally friendly inhibitor for mild steel corrosion in 1 M H2SO4 solution

The efficiency of Acacia cyanophylla leaves extract as an environmentally friendly inhibitor for mild steel in aerated aqueous 1 M H₂SO₄ solution has been investigated by potentiodynamic polarization measurements and electrochemical impedance spectroscopy techniques. Addition of inhibitor decreases the corrosion current whereas the corrosion potential values show slight shifts in positive directions. Inhibition efficiency was found to be about 93% (the maximum value was determined from the polarization curve). Efficiencies obtained from both electrochemical techniques are in good agreement. Adsorption of Acacia cyanophylla leaves extract on mild steel surface in 1 M H₂SO₄ solution obeys Langmuir adsorption isotherm. Polarization curves were also obtained at different temperatures in order to measure changes of corrosion rate. Corrosion current increases and inhibition efficiency decreases with temperature increasing in H₂SO₄ solutions with and without Acacia cyanophylla extract. Corrosion parameters also changed with exposure time. Copyright © 2010 John Wiley & Sons, Ltd.     

Adsorption and inhibitive properties of aminobiphenyl and its Schiff base on mild steel corrosion in 0.5 M HCl medium

Electrochemical measurements were performed to investigate the effectiveness and adsorption behaviour of aminobiphenyl (Aph) and 2-(3-hydroxybenzylideneamino)biphenyl (Aph-S), as corrosion inhibitors for mild steel (MS) in 0.5 M HCl solution. Potentiodynamic polarization, linear polarization resistance (LP) and electrochemical impedance spectroscopy (EIS) techniques were applied to study the metal corrosion behaviour in the absence and presence of different concentrations of Aph and Aph-S. In order to gain more information about adsorption mechanism the AC impedance technique was used to evaluate the potential of zero charge (PZC) from polarization resistance (R_p) versus voltage (E) plot. Potentiodynamic polarization measurements showed that Aph act as cathodic type inhibitor where as Aph-S act mixed type. The inhibition efficiency (IE%) increases with increasing concentration of compounds and reached 92.6% for Aph and 97.2% for Aph-S at 5 × 10⁻³ M. Double layer capacitance (C_dl) and polarization resistance (R_p) values are derived from Nyquist plots obtained from AC impedance studies. The experimental data fit Langmuir isotherm for both Aph and Aph-S, and from the adsorption isotherm some thermodynamic data for the adsorption processes are calculated and discussed. The effect of exposure time on the corrosion behaviour of mild steel in the absence and presence of inhibitor over 168 h was also studied.     

Pitting behavior on super 13Cr stainless steel in 3.5% NaCl solution in the presence of acetic acid

The pitting behavior was investigated on super 13Cr stainless steels in 3.5% NaCl solution in the presence of HAc. The electrochemical measurements including potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and chronoamperometric experiments were carried out, as well as the SEM surface analysis. The parameters such as E _corr and I _corr were obtained by fitting technique. Moreover, the equivalent circuit model was applied in the analysis of Nyquist plots, and ZsimWin software was used to analyze the EIS data. The results indicate that the pitting corrosion is accelerated with increasing the amounts of HAc. In addition, pitting nucleation and growth mechanisms were described in this work.     

Simultaneous in situ time resolved SR-XRD and corrosion potential analyses to monitor the corrosion on copper

The focus of this study consists of examining how simultaneous SR-XRD and electrochemical measurements can provide information on the effectiveness of stabilization and storage treatments of copper artefacts in aqueous solution. The electrochemical cell used here was designed for in situ, time resolved SR-XRD studies of corrosion and inhibition studies on cultural heritage materials. Key objectives of the new cell were to monitor corrosion layers on alloys with realistic metallographic structures and to obtain co-incident, time resolved, electrochemical data such as reduction measurements, oxidation measurements and corrosion potential (E_corr) measurements. Here we present some early results from the cell. Firstly, a correlated SR-XRD and corrosion potential (E_corr) study of the reduction of nantokite during storage in sodium sesquicarbonate, which shows that the surface chemistry continues to change after E_corr has stabilized. Secondly, the use of X-ray data to identify specific changes occurring as a function of potential in the forced reduction of a more complex system.     

Corrosion inhibition of copper in chloride media by 2-mercapto-4-(p-methoxyphenyl)-6-oxo-1,6-dihydropyrimidine-5-carbonitrile: Electrochemical and theoretical study

Electrochemical frequency modulation (EFM), electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization have been used to investigate the inhibition effect of a new pyrimidine heterocyclic derivative, namely 2-mercapto-4-(p-methoxyphenyl)-6-oxo-1,6-dihydropyrimidine-5-carbonitrile (MPD) on copper corrosion in 3.5% NaCl solutions at 25 ± 1 °C. The electrochemical investigations showed that MPD gives sufficient inhibition against copper corrosion in 3.5% NaCl solutions. Potentiodynamic polarization measurements have shown that the MPD inhibit both the cathodic and anodic processes and thus it classified as mixed-type inhibitor. EIS measurements indicate that the values of constant phase elements (CPEs) tend to decrease and both charge-transfer resistance and inhibition efficiency tend to increase by increasing the inhibitor concentration. Electrochemical kinetic parameters obtained using EFM methods were comparable with that calculated from traditional measurements (EIS and potentiodynamic polarization). Molecular simulation technique was used to investigate the adsorption configuration of MPD on copper surface. Number of electrons transferred from MPD to the copper surface was calculated by semi-empirical quantum chemical calculations.     

Inhibitory effects of Murraya koenigii (curry leaf) leaf extract on the corrosion of mild steel in 1 M HCl

Abstract

The inhibitive effect of the Murraya koenigii (curry leaf) leaf extract on the corrosion of mild steel in 1 M HCl was investigated by using weight loss, open circuit potential measurements, potentiostatic polarization techniques, and impedance analysis. The results show that Murraya koenigii extract is an effective corrosion inhibitor for protecting the corrosion of mild steel in 1 M HCl medium even at stimulated conditions. The inhibition efficiency increases with increasing the concentration of the inhibitor in the medium. The percentage inhibitor efficiency under stagnant condition calculated based on weight loss method is found to be above 94.5% when the medium contains 1000 ppm of the inhibitor.     

Correction to: The effect of small silver inclusions on the palladium activity in formicacid oxidation reaction and corrosion stability

A PdAg deposit containing ~ 25 at.% Ag is obtained by the electrochemical codeposition from an aqueous solution of Pd and Ag sulfates (Au support, 0.5 M H₂SO₄). The deposit is characterized by means of various physical, physicochemical, and electrochemical methods. The PdAg deposit demonstrates the ~ 2 times higher specific activity (per the electrochemically active surface area (EASA) of Pd) in the formic acid oxidation reaction (FAOR) as compared with the individual Pd deposit prepared under the same conditions. The effect of silver additions on the palladium activity depends on many factors. The corrosion stability of PdAg is studied in 0.5 M H₂SO₄ solution based on the overall cyclic voltammograms (CVAs) and also on anodic and cathodic half-cycles in the region E = 0.3 − 1.25 V (vs. reversible hydrogen electrode (RHE)). The electrochemical estimates are compared with the results of direct analytical determination of dissolution products in solution after anodic polarization of deposits. The total amounts of Pd dissolved substantially increase with incorporation of Ag, which is associated, first of all, with the considerable increase in the EASA; at the same time, the specific dissolution of Pd also substantially increases. The possible factors determining the active dissolution of PdAg deposits are discussed; in particular, the specific mechanism of their dissolution via silver adatoms is proposed.

     

Software and Instrumentational Methods of Enhancing the Resolution in Electrochemical Noise Measurements

Several methods of enhancing the signal-to-noise ratio for instrumentation designed to measure electrochemical noise are practically tested. The experiments are carried out using model RC-circuits and lielectrolyte electrochemical cells. Strong limitations in the tested objects’ impedance values are found due to the input current noise of the instrumentation, especially during the parallel connection of several channels. The advantages of a two-channel scheme for automatically compensating the instrument’s self noise are demonstrated. Different methods of lowering the dispersion of the frequency dependences of the spectral power density of electrochemical noise are compared. It is shown that averaging over segments with an overlap is the most effective method but averaging over frequencies can lead to large distortions when investigating electrochemical systems.

     

Corrosion inhibition of mild steel in hydrochloric acid by betanin as a green inhibitor

The effect of betanin (2,6-pyridinedicarboxylic acid, 4-(2-(2-carboxy-5-(beta-D-glucopyr-anosyloxy)-2,3-dihydro-6-hydroxy-1H-indol-1-yl)ethenyl)-2,3-dihydro-(S-(R*,R*))) on the corrosion inhibition of mild steel has been investigated in 1 M HCl solution. Weight loss method, potentiodynamic polarization, and electrochemical impedance spectroscopy techniques were applied to study the mild steel corrosion behavior in the absence and presence of different concentrations of betanin under the influence of various experimental conditions. The results obtained showed that betanin is a good “green” inhibitor for mild steel in 1 M HCl solution. Scanning electron microscopy observations of the steel surface confirmed the protective role of the inhibitor. The polarization curves showed that betanin behaves mainly as a mixed-type inhibitor. Maximum inhibition efficiency (98%) is obtained at betanin concentrations of 0.01 M. The results obtained from weight loss, polarization, and impedance measurements are in good agreement.     

Kinetics,Mechanistic and Theoretical Studies on Scavenging Activities of Antioxidants Using 1,2-Dinitrobenzene DNB/DNB•− and DNB/DNB2– Model Systems: Cyclic Voltammetric and Quantum Semi-Empirical Data Interpretation

Here we are presenting complete electrochemical studies on redox activities of 1,2-dinitrobenzene (DNB) in the presence of antioxidants–quercetin, morin, rutin, ascorbic acid and β-carotene. Bimolecular rate constants (k₂), antioxidant activities (K_a) and diffusion coefficients (D_o) were evaluated from changes in voltammeric responses and electrochemical parameters in the presence of antioxidant’s concentrations. Theoretical charge calculations by PM3 parameterization were done which further justified our experimental electrochemical work and proposed scavenging mechanism. Present findings were also compared in details with our previously reported studies on 1,3- and 1,4-dinitrobenzene systems for their interactions with antioxidants.

     

Use of an amide-type corrosion inhibitor synthesized from the coffee bagasse oil on the corrosion of Cu in NaCl

An amide, namely N-[2-[(2-hydroxyethyl) amino] ethyl]-amide, extracted from the fatty acids contained in the coffee bagasse, has been investigated as a possible green corrosion inhibitor for copper in 3.5% NaCl by using potentiodynamic polarization curves and electrochemical impedance spectroscopy measurements. Results were complemented by detailed scanning electronic microscopy, FTIR and gas chromatography studies. Results have shown that N-[2-[(2-hydroxyethyl) amino] ethyl]-amide is a good, mixed type of corrosion inhibitor, with an efficiency that increases with its concentration but it decreases with a rise in the temperature. It adsorbs chemically onto the copper surface by following a Langmuir type of adsorption isotherm.     

用三电极体系研究铜在微液滴下的电化学腐蚀

由于大气腐蚀高阻抗的特征, 传统的参比电极难以用于大气腐蚀研究之中. 为了获取准确的大气腐蚀电化学信息, 我们需要对传统的参比电极进行修改. 本文在三电极体系中采用修改的参比电极, 通过电化学阻抗和电化学极化两种方法研究铜在含有(NH₄)₂SO₄液滴下的腐蚀行为, 结果表明液滴下铜的平均腐蚀速率随着液滴体积从1到20 μL增加而减小; 当液滴高度不超过850 μm时, 平均腐蚀速率随着液滴高度的减小却迅速地增大. 此外, 电化学阻抗和电化学极化得出的腐蚀速率相一致, 这证明修改的参比电极可以用于液滴下的大气腐蚀研究.     

Effects of Sintering Temperature and Press Pressure on the Microstructure and Electrochemical Behaviour of the Ag2O/GO Nanocomposite

The purpose of this study was to evaluate the effects of press pressure and sintering temperature on the microstructure and electrochemical performance of silver oxide-graphene oxide composite as a novel electrode produced by the powder metallurgy (PM) route. Scanning electron microscopy method used to investigate the microstructure of electrodes and energy dispersive X-ray spectroscopy analysis method was used for point analysis. Potentiodynamic polarization and electrochemical impedance spectroscopy methods were used to research the effects of sintering temperature and press pressure on the electrochemical behaviour in the 1.4 wt % KOH solution and electrical discharge test was used for evaluate the ultimate electrical capacity of silver oxide-zinc batteries with electrolyte of the 1.4 wt % KOH solution.

     

Ceratonia siliqua extract as a green corrosion inhibitor for copper and brass in nitric acid solutions

ABSTRACT

The influence of extract of ceratonia siliqua extract on the corrosion of copper and brass in aqueous 1 M nitric acid was examined by weight loss, potentiodynamic polarization, electrochemical impedance spectroscopy and electrochemical frequency modulation techniques. The surface morphology was analyzed using scanning electron microscope and energy dispersive X-ray techniques. Potentiodynamic polarization curves indicated that the plant extract behaves as cathodic inhibitor. The results indicate that the extract solution of the plant could serve as an effective inhibitor for the corrosion of copper and brass in nitric acid media. As temperature increases, percentage of inhibition decreases. The degree of surface coverage of the adsorbed inhibitor was determined by weight-loss technique, and it was found that the results obeyed the Langmuir adsorption isotherm.     

La1－xSrxNi1－yFeyO3型钙钛矿双功能氧电极的电化学性能研究

采用溶胶-凝胶法制备了一系列La_1－xSr_xNi_1－yFe_yO₃ (x＝0, 0.1, 0.2, 0.5; y＝0～1.0)型的钙钛矿催化剂, 以活性碳为载体, PTFE乳液为粘接剂制备双功能氧电极. 对催化剂进行了XRD结构分析以及SEM分析和BET比表面积测量. 采用三电极体系测试了氧电极的稳态极化曲线和电化学交流阻抗谱并对其阴极极化和阳极极化的交流阻抗谱图进行分析. 通过等效电路的拟合研究了该系列双功能氧电极氧还原反应的工作机理. 实验表明对于LaNiO₃化合物, B位掺杂可显著提高催化剂的电催化性能; 电极氧还原反应的极化主要由电荷转移反应和Nernstian扩散过程造成. 通过各个电极对于催化分解H₂O₂的分解速率常数的测定得知, Ni离子对于催化H₂O₂分解反应的活性大于Fe离子, 继续在对于氧还原反应和氧析出反应都具有较高电催化活性的LaNi_0.8Fe_0.2O₃催化剂上进行A位掺杂Sr离子后显著提高了催化剂分解H₂O₂的催化活性, 主要是因为氧空位的增多和金属离子d电子含量的降低有利于催化分解H₂O₂的活性的提高, 但由于氧空位的增多导致催化剂电导率的降低, 所以其电催化活性降低了. 通过多圈循环伏安扫描的测试, 催化剂LaNi_0.8Fe_0.2O₃有很好的稳定性.     

Dipole Moment Studies of n-butanol,i-butanol and t-butanol with Chlorobenzene Complexes

Abstract

The dipole moments of H-bonded complexes of n-butanol, i-butanol and t-butanol with chlorobenzene in benzene were investigated from dielectric measurements at 455 kHz and at temperature 303.16 K. The dipole moment of the complex (μab), interaction dipole moment (Δμ) and induced polarization (Pab) for thermodynamically most favoured geometry of 1:1 complexes in these systems were determined. The results shows that the complexation is due to charge redistribution effect in all cases studied and the tendency of complex formation is maximum in n-butanol system.     

A study on the electrochemical polymerization, characterization, and corrosion protection of o-toluidine on steel

Poly(o-toluidine) (POT) coatings were electrochemically synthesized on 304 stainless steel using cyclic voltammetric method. These coatings were characterized by Fourier transform infrared spectroscopy, UV–vis absorption spectroscopy, and cyclic voltammetry. The corrosion performance of POT coating in aqueous 3 wt% sodium chloride was assessed by the electrochemical techniques such as open circuit potential measurements, potentiodynamic polarization technique, cyclic potentiodynamic polarization measurements, and electrochemical impedance spectroscopy. The results reveal that POT coating on 304 stainless steel prevents general and localized corrosion, and reduces the exchange current density almost by a factor of 45 than bare 304 stainless steel.