Combination of therapeutic ultrasound with antibiotics interfere with the growth of bacterial culture that colonizes skin ulcers: An in-vitro study

Staphylococcus aureus and Escherichia coli are among the major bacterial species that colonize skin ulcers. Therapeutic ultrasound (TUS) produces biophysical effects that are relevant to wound healing; however, its application over a contaminated injury is not evidence-based. The objective of this research was to analyze the effect of TUS on in vitro-isolated S. aureus and E. coli, including the combination of ultrasound and antibiotics, in order to assess their antibiotic action on bacterial susceptibility. For the experiments, the bacterial strains were suspended in saline, then diluted (10⁴ CFU/mL) for irradiation (at 1 and 3 MHz, 0.5 and 0.8 W/cm² for 0 and 15 min) and the combination treatment of ultrasonication and antibiotics was administered by adding nalidixic acid (S. aureus) and tetracycline (E. coli) at concentrations equivalent to 50% of the minimum inhibitory concentration (MIC). The experiments were carried out in duplicate with six repetitions. The suspensions were inoculated on to Petri plates and incubated at 37 °C and the colony forming units (CFUs) were counted after 24 h. The results were subjected to the Shapiro–Wilk normality test, followed by parametric ANOVA and Tukey’s post hoc test at a significance level of 1%. The results demonstrated that the action of TUS at 1 MHz inhibited bacterial growth while at 3 MHz, bacterial growth was observed in both species. However, the synergistic combination of ultrasound and antibiotics was able to inhibit the growth of both bacteria completely after 15 min of ultrasonication. The results suggest that the action of ultrasound on S. aureus and E. coli are dependent on the oscillation frequency as well as the intensity and time of application. The combination of ultrasound with antibiotics was able to inhibit bacterial growth fully at all frequencies and doses in both species.     

Facile synthesis of nanostructured CuO for low temperature NO2 sensing

Detection of environmental pollutant and health hazardous, nitrogen dioxide (NO₂) is reported using nanostructured CuO particulates (NPs). Powder X-ray diffraction and field emission scanning electron microscopy were used to probe crystalline phase and morphological details, respectively. Small crystallites of ∼10–12 nm and a strain of 4% were found in the leafy structure of CuO. Raman studies further supported the presence of nanosized CuO phase. This is the first instance of utilizing CuO NPs to detect 5 ppm of NO₂ even at a low operating temperature of 50 °C. The highest sensitivity for NO₂ was observed at 150 °C, for the first time, in CuO NPs. A low activation energy of 0.18 eV was found for sensing process. The CuO NPs sensor responded to NO₂ within a few seconds and recovered totally under a minute. The kinetics of the NO₂ gas adsorption on the CuO film surface was described following the Elovich model.     

Sonochemical fabrication of edible fragrant antimicrobial nano coating on textiles and polypropylene cups

We report on a simple and effective ultrasound-assisted deposition of vanillin nanoparticles (∼50 nm in size), raspberry ketone (RK) nanoparticles (∼40 nm in size) and camphor nanoparticles (width ∼30 nm, length ∼40 nm in size) on textiles and on polypropylene surfaces. The excellent antibacterial and antifungal activity of the fragrant coatings on cotton bandages, and polypropylene surface against Escherichia coli (E. coli), Salmonella paratyphi A (S. paratyphi A) and the yeast Candida albicans (C. albicans) cultures was demonstrated. It is worth pointing out that these fragrant materials are edible, making them very useful for packaging. The mechanism of the edible fragrant coating formation and adhesion to the textile was discussed, and finally an up-scaling of the sonochemical process for textile coating was carried out.     

Synergistic effect of ultrasonic pre-treatment combined with UV irradiation for secondary effluent disinfection

The ultraviolet (UV) disinfection efficiency is often affected by suspended solids (SS). Given their high concentration or large particle size, SS can scatter UV light and provide shielding for bacteria. Thus, ultrasound is often employed as a pre-treatment process to improve UV disinfection. This work investigated the synergistic effect of ultrasound combined with UV for secondary effluent disinfection. Bench-scale experiments were conducted in using samples obtained from secondary sedimentation tanks. These tanks belonged to three wastewater treatment plants in Beijing that use different kinds of biological treatment methods. Several parameters may contribute to the changes in the efficiency of ultrasound and UV disinfection. Thus, the frequency and energy density of ultrasound, as well as the SS, were investigated. Results demonstrated that samples which have relatively higher SS concentrations or higher percentages of larger particles have less disinfection efficiency using UV disinfection alone. However, the presence of ultrasound could improve the disinfection efficiency because it has synergistic effect. Changes in the particle size distribution and SS concentration notably affected the efficiency of UV disinfection. The efficiency of Escherichia coli elimination can be decreased by 1.2 log units as the SS concentration increases from 16.9 mg/l to 25.4 mg/l at a UV energy density of 40 mJ/cm². UV disinfection alone reduced the E. coli population by 3.4 log units. However, the synergistic disinfection of ultrasound and UV could reach 5.4 log units during the reduction of E. coli at a 40 kHz frequency and an energy density of 2.64 kJ/l. The additional synergistic effect is 1.1 log units.     

Synergetic effects of ultrasound and slightly acidic electrolyzed water against Staphylococcus aureus evaluated by flow cytometry and electron microscopy

This study evaluated the synergetic effects of ultrasound and slightly acidic electrolyzed water (SAEW) on the inactivation of Staphylococcus aureus using flow cytometry and electron microscopy. The individual ultrasound treatment for 10 min only resulted in 0.36 log CFU/mL reductions of S. aureus, while the SAEW treatment alone for 10 min resulted in 3.06 log CFU/mL reductions. The log reductions caused by combined treatment were enhanced to 3.68 log CFU/mL, which were greater than the sum of individual treatments. This phenomenon was referred to as synergistic effects. FCM analysis distinguished live and dead cells as well as revealed dynamic changes in the physiological states of S. aureus after different treatments. The combined treatment greatly reduced the number of viable but nonculturable (VBNC) bacteria to 0.07%; in contrast, a single ultrasound treatment for 10 min induced the formation of VBNC cells to 45.75%. Scanning and transmission electron microscopy analysis revealed that greater damage to the appearance and ultrastructure of S. aureus were achieved after combined ultrasound-SAEW treatment compared to either treatment alone. These results indicated that combining ultrasound with SAEW is a promising sterilization technology with potential uses for environmental remediation and food preservation.     

Combined effect of ultrasound,heat, and pressure on Escherichia coli O157:H7, polyphenol oxidase activity,and anthocyanins in blueberry (Vaccinium corymbosum) juice

The objective of this study was to evaluate the effect of different treatments—heat treatment (HT), sonication (SC), thermosonication (TS), manosonication (MS), manothermal (MT), and manothermosonication (MTS) on Escherichia coli O157:H7, polyphenol oxidase (PPO), and anthocyanin content in blueberry juice. First, samples were treated at different temperatures (30, 40, 50, 60, 70, and 80 °C) and power intensities (280, 420, 560, and 700 W) for 10 min. Subsequently, samples were treated using combinations of power intensity and mild temperature for 10 min. For further study, samples were treated using HT (80 °C), TS (40 °C, 560 W), MT (350 MPa, 40 °C), MS (560 W, 5 min/350 MPa), or MTS (560 W, 5 min, 40 °C/350 MPa, 40 °C) for 5, 10, 15, 20 min for each treatment, and the results compared between treatments. HT significantly reduced PPO activation (2.05% residual activity after only 5 min), and resulted in a 2.00-log reduction in E. coli O157:H7 and an 85.25% retention of anthocyanin. Escherichia coli O157:H7 was slightly inactivated by TS after 5 min (0.17-log reduction), while residual PPO activity was 23.36% and anthocyanin retention was 98.48%. However, Escherichia coli O157:H7 was rapidly inactivated by MTS (5.85-log reduction) after 5 min, while anthocyanin retention was 97.49% and residual PPO activity dropped to 10.91%. The destruction of E. coli cells as a result of these treatments were confirmed using SEM and TEM. Therefore, a combination of sonication, high pressure, and mild heat allows the safety of blueberry juice to be maintained without compromising the retention of desirable antioxidant compounds.     

Effect of high intensity ultrasound on the fermentation profile of Lactobacillus sakei in a meat model system

The objective of this study was to investigate the efficacy of high intensity ultrasound on the fermentation profile of Lactobacillus sakei in a meat model system. Ultrasound power level (0–68.5 W) and sonication time (0–9 min) at 20 °C were assessed against the growth of L. sakei using a Microplate reader over a period of 24 h. The L. sakei growth data showed a good fit with the Gompertz model (R² > 0.90; SE < 0.042). Second order polynomial models demonstrated the effect of ultrasonic power and sonication time on the specific growth rate (SGR, μ, h⁻¹) and lag phase (λ, h). A higher SGR and a shorter lag phase were observed at low power (2.99 W for 5 min) compared to control. Conversely, a decrease (p < 0.05) in SGR with an increase in lag phase was observed with an increase in ultrasonic power level. Cell-free extracts obtained after 24 h fermentation of ultrasound treated samples showed antimicrobial activity against Staphylococcus aureus, Listeria monocytogenes, Escherichia coli and Salmonella typhimurium at lower concentrations compared to control. No significant difference (p < 0.05) among treatments was observed for lactic acid content after a 24 h fermentation period. This study showed that both stimulation and retardation of L. sakei is possible, depending on the ultrasonic power and sonication time employed. Hence, fermentation process involving probiotics to develop functional food products can be tailored by selection of ultrasound processing parameters.     

Shape-controlled synthesis of Cu2O nano/microcrystals and their antibacterial activity

Uniform cuprous oxides with different morphologies have been successfully synthesized using polyvinylpyrrolidone (PVP) as a capping agent. X-ray diffraction (XRD), scanning electron microscopy (SEM), UV–vis spectrophotometer, Fourier transform infrared spectrometer (FTIR) and X-ray photoelectron spectroscopy were employed to characterize the structure and morphology of cuprous oxides. It was found that the reaction conditions such as PVP, reducing agent and complexing agent played important roles in the formation of regular cuprous oxide crystals. In addition, their antibacterial activity against Bacillus subtilis (B. subtilis), Staphylococcus aureus (S. aureus), Escherichia coli (E. coli) and Pseudomonas aeruginosa (P. aeruginosa) was also investigated by the Oxford cup method. Results suggested that cuprous oxides are selective in their antibacterial action. They display effective antibacterial activity against S. aureus, B. subtilis and P. aeruginosa. There is no bactericidal ability against E. coli in the tested concentration range, which indicates that E. coli may be a Cu(I)-tolerant bacterium.     

Green synthesis of finely-dispersed highly bactericidal silver nanoparticles via modified Tollens technique

In this article, we represent a versatile and effective technique which using non-toxic chemicals to prepare stable aqueous dispersions of silver nanoparticles (NPs) via modified Tollens process. It was shown that as-prepared silver colloids consisted of finely-dispersed NPs with average diameter about 10 nm and a relatively narrow size distribution. Moreover, they could be stored very stable after several months without observation of aggregates or sedimentation. In comparison with previous works where Tollens process was being used, we for the first time applied UV-irradiation simultaneously with glucose reduction of silver salt through NPs preparation. The colloidal solutions of silver NPs were found to exhibit a high antibacterial activity against gram-negative Escherichia coli. The concentration of silver leading to a complete inhibition of bacteria growth was revealed as low as at 1.0 μg ml⁻¹ and found much lower compared to earlier reports. These advantages of aqueous dispersions of silver NPs make them ideal for green industrial, medicinal, microbiological and other applications.     

Utilization of ultrasonic irradiation as a green and effective strategy to prepare poly(N-vinyl-2-pyrrolidone)/modified nano-copper (II) oxide nanocomposites

The present paper describes the result of investigations into preparation of novel nanocomposites (NCs) based on poly(N-vinyl-2-pyrrolidone) (PVP) as a biocompatible polymer and modified copper (II) oxide nanoparticles (NPs) as a nano-filler. To achieve optimum NCs properties, different ratios of modified copper (II) oxide NPs (3, 5, and 7 wt%) were used to fabricate PVP NCs and also the ultrasonic irradiation was utilized to perform these processes as a fast and effective method. Subsequently, the structure of the obtained nanohybrids was characterized by various techniques. The suitable incorporation between PVP matrix and modified CuO NPs can be seen from the FT-IR spectra. The obtained NCs indicated an efficient thermal improvement in comparison to the pristine polymer. Also, the uniform dispersion of modified CuO NPs in the PVP matrix was detected by FE-SEM and EDX. According to UV absorption spectra, it is clear that these NCs can be used in UV protecting applications.     

Two and four photon absorption and nonlinear refraction in undoped,chromium doped and copper doped ZnS quantum dots

The ZnS quantum dots (QDs) with Cr and Cu doping were synthesized by chemical co-precipitation method. The nanostructures of the prepared undoped and doped ZnS QDs were characterized by UV–vis spectroscopy, Transmission electron microscopy (TEM) and X-ray diffraction (XRD). The sizes of QDs were found to be within 3–5 nm range. The nonlinear parameters viz. Two photon absorption coefficient (β₂), nonlinear refractive index (n₂), third order nonlinear susceptibility (χ³) at wavelength 532 nm and Four photon absorption coefficient (β₄) at wavelength 1064 nm have been calculated by Z-scan technique using nanosecond Nd:YAG laser in undoped, Cr doped and Cu doped ZnS QDs. Higher values of nonlinear parameters for doped ZnS infer that they are potential material for the development of photonics devices and sensor protection applications.     

Effect of calcination temperature on phase transformation,structural and optical properties of sol–gel derived ZrO2 nanostructures

Zirconia (ZrO₂) nanostructures of various sizes have been synthesized using sol–gel method followed by calcination of the samples from 500 to 700 °C. The calcined ZrO₂ powder samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier-transform infra-red spectroscopy (FT-IR), UV–visible spectroscopy (UV–vis.), Raman spectroscopy (RS) and thermogravimetric analysis (TGA). The phase transformation from tetragonal (t) to monoclinic (m) was observed. The average diameter of the ZrO₂ nanostructures calcined at 500, 600 and 700 °C was calculated to be 8, 17 and 10 nm, respectively. The ZrO₂ sample calcined at 500 °C with tetragonal phase shows a direct optical band gap of 5.1 eV. The value of optical band gap is decreased to 4.3 eV for the ZrO₂ calcined at 600 °C, which contains both tetragonal (73%) and monoclinic (27%) phases. On further calcination at 700 °C, where the ZrO₂ nanostructures have 36% tetragonal and 64% monoclinic phases, the optical band gap is calculated to be 4.8 eV. The enhancement in optical band gap for ZrO₂ calcined at 700 °C may be due to the rod like shape of ZrO₂ nanostructures. The tetragonal to monoclinic phase transformation was also confirmed by analyzing Raman spectroscopic data. The TG analysis revealed that the ZrO₂ nanostructure with dominance of monoclinic phase is found to be more stable over the tetragonal phase. In order to confirm the phase stability of the two phases of ZrO₂, single point energy is calculated corresponding to its monoclinic and tetragonal structures using density functional theory (DFT) calculations. The results obtained by theoretical calculations are in good agreement with the experimental findings.     

Synthesis,crystal growth and characterization of a semiorganic material: Calcium dibromide bis(glycine) tetrahydrate

Single crystals of semiorganic material calcium dibromide bis(glycine) tetrahydrate were grown from aqueous solution. The crystal belongs to monoclinic system, with a = 13.261(5) Å, b = 6.792(2) Å, c = 15.671(9) Å and β = 91.68(4)°. The presence of the elements in the title compound was confirmed by energy dispersive X-ray analysis. The solubility and metastable zone width were found. The grown crystals were tested by powder XRD, FTIR, Thermo Gravimetric and Differential Thermal Analysis, UV–vis–NIR analysis, dielectrical and mechanical studies. The transmittance of calcium dibromide bis(glycine) tetrahydrate crystal has been used to calculate the refractive index n, the extinction coefficient K and both the real ɛ_r and imaginary ɛ_i components of the dielectric constant as functions of wavelength. The optical band gap of calcium dibromide bis(glycine) tetrahydrate is 3.23 eV.     

Structural characterization and X-ray analysis by Williamson–Hall method for Erbium doped Aluminum Nitride nanoparticles,synthesized using inert gas condensation technique

We have synthesized AlN nanoparticles (NPs) doped in-situ with Er (AlN:Er) using inert gas condensation technique. Using x-ray diffraction (XRD) peak broadening analysis with the Williamson–Hall (W–H) Uniform Deformation Model (UDM) the crystallite size of the NPs and the strain in NPs were found to be 80±38 nm and 3.07×10⁻³±0.9×10⁻³ respectively. In comparison, using the Debye–Scherrer's (DS) formula, we have inferred that the crystallite size of the NPs was 23±6 nm and the average strain was 4.3×10⁻³±0.4×10⁻³. The scanning electron microscopy images show that the NPs are spherical and have an average diameter of ∼300 nm. The crystallite size is smaller than the size of the NPs revealing their polycrystalline behavior. In addition, the NPs strain, stress and energy density were also calculated using W–H analysis combined with the Uniform Deformation Stress Model (UDSM) and the Uniform Deformation Energy Density Model (UDEDM). Suggested by the spherical geometry and polycrystalline nature of the AlN NPs, the strain computed from UDM, UDSM and UDEDM were in agreement confirming an isotropic mechanical nature of the particle. Luminescence measurements revealed the temperature dependence of the optical emission of the Er³⁺ ions, confirming the use of AlN:Er NPs for nano-scale temperature sensing.     

Synthesis,characterization and luminescence study of dimethyl[N-arylmethylenethiobenzahydrazonato]indium

Five dimethylindium complexes of type Me₂InL [L = N-(4-methoxy)benzylidenethiobenzahydrazonato (1), N-(3,4-dimethoxy)benzylidenethiobenzahydrazonato (2), N-(4-N,N-dimethylamino)benzylidenethiobenzahydrazonato (3), N-(2-naphthyl)methylene thiobenzahydrazonato (4) and N-(9-anthryl)methylenethiobenzahydrazonato (5)] have been synthesized by reaction of trimethylindium with appropriate N-arylmethylenethiobenzahydrozones. The complexes obtained have been characterized by elemental analysis, ¹H NMR, IR and mass spectroscopy. Compounds 1–5 emit blue colors at λ_max = 432–479 nm when irradiated by UV light. The electroluminescent (EL) properties of 1–5 were examined by fabricating EL devices using 1–5 as emitter, respectively. The EL bands are located in the green region (513–578 nm).     

The disinfection effect of a novel continuous-flow water sterilizing system coupling dual-frequency ultrasound with sodium hypochlorite in pilot scale

In this paper, a self-designed novel continuous-flow water disinfection system coupling dual-frequency ultrasound (US) with chemical disinfectant sodium hypochlorite (NaClO) was tested in a pilot scale using a simulated effluent containing Bacillus subtilis (B. subtilis), one of the indicators of water treatment efficiency. A suspension having a B. subtilis concentration of approximately 10⁴ CFU/mL was introduced into the system to (1) investigate disinfection efficiency of US pretreatment with NaClO (US + NaClO) and simultaneous US and NaClO (US/NaClO) disinfection under different single frequencies; (2) further examine the disinfection efficiency of these two processes with dual-frequency US; and (3) identify dosage reduction of chlorine in this disinfection system. The results demonstrated that lower dual-frequency (17 kHz + 33 kHz) US pretreatment with NaClO disinfection and simultaneous higher dual-frequency (70 kHz + 100 kHz) US and NaClO were beneficial to bacterial inactivation in terms of sterilizing efficiency. It has also been observed that US pretreatment with lower combination of 17 + 33 kHz frequencies showed better enhancement in which log reduction reached to 3.82 after 10 min chlorine reaction (chlorine alone was 0.22 log reduction), nearly 1 log reduction higher than single frequencies at the same constant power. Consequently, at equivalent power dissipation levels, US of lower frequencies combination pretreatment with NaClO disinfection performed such a promising process that one-thirds (from 12 mg/L NaClO reduced to 8 mg/L NaClO) of the required NaClO dosage was reduced for the ideal disinfection efficiency of 4 log reduction, namely 100% disinfection. And the utilization efficiency of NaClO was increased from 37.67% to 85.25% in 30 min of treatment time using an optimized combination of pretreatment and chlorination.     

Analysis of sterilization effect by pulsed dielectric barrier discharge

Atmospheric pressure (AP) plasmas can sterilize against almost all kinds of bacteria because many ions and reactive species, such as oxygen atoms and ozone, etc., are generated during AP plasmas. So AP plasmas are proper processes for application to air cleaners and sterilizers. The aim of this paper is to evaluate a germicidal effect caused by pulsed plasma system in air utilizing a dielectric barrier discharge (DBD) type reactor incorporating alumina, glass, etc. Escherichia coli, Bacillus subtilis and Pseudomonas aeruginosa bacteria were used for this sterilization experiment. For analysis of the relationship between sterilization results and chemical species generated in the discharge, we used optical emission spectroscopy and we checked emission spectra by atomic oxygen (394.2 and 436.8 nm) and second positive system of nitrogen (337.1 nm). Experimental results showed that DBD treatment during 70 s sterilized E. coli with 99.99% effectively and ozone molecules were the dominant germicidal species. From these results we concluded that the pulsed DBD system is very effective for sterilization.     

Disinfection effect of a continuous-flow ultrasound/ultraviolet baffled reactor at a pilot scale

An ultrasound/ultraviolet (US/UV) baffled reactor was developed to fill the gap in ultraviolet (UV) disinfection associated with disinfection efficiency. According to the previously selected operational condition, a continuous-flow US/UV baffled reactor was continuously operated in a wastewater treatment plant at a pilot scale for nearly three months, and the disinfection influent and effluent were analyzed, including fecal coliforms, Escherichia coli, and fecal streptococci. The US/UV baffled reactor could guarantee a high effluent disinfection performance in terms of fecal coliforms removal even with the fluctuation of the secondary effluent. All the disinfected effluents satisfied the requirement of the “Pollutants Discharge Standard of Municipal Wastewater Treatment Plant in China” (fecal coliforms below 1000 CFU/L for class 1A), and 87% of the tested fecal coliforms concentration in the disinfected effluent was below 100 CFU/L, nearly eliminating all fecal coliforms. Further analysis of the E. coli and fecal streptococci showed the broad disinfection ability and high disinfection efficiency of the US/UV baffled reactor. The flexibility of the specific energy consumption for the disinfection system depends on the water quality.     

Silver nanoparticle in situ growth within crosslinked poly(ester-co-styrene) induced by UV irradiation: aggregation control with exposure time

Silver nanoparticles (NPs) were photogenerated in situ in crosslinked poly(ester-co-styrene) resins (self-standing films and monoliths) by irradiating the samples with UV light. Addition of the silver salt solution did not interfere in the resin curing process and silver reduction was not detected during sample crosslinking. The samples were characterized by absorption spectroscopy and transmission electron microscopy. The initially broad and asymmetric surface plasmon resonance band was narrowed and blue-shifted as the exposure time to UV light was increased. Samples illuminated up to 120 min have an average particle size near 9.0 nm; a decrease to ∼5.0 nm was observed for longer exposure times up to 790 min. The asymmetric surface plasmon resonance band was due to particle aggregation; higher irradiation times led to a uniform particle distribution within the polymer matrix.     

Ultrasonic assisted-Fenton-like degradation of nitrobenzene at neutral pH using nanosized oxides of Fe and Cu

Ultrasonic-assisted heterogeneous Fenton reaction was used for degradation of nitrobenzene (NB) at neutral pH conditions. Nano-sized oxides of α-Fe₂O₃ and CuO were prepared, characterized and tested in degradation of NB (10 mg L⁻¹) under sonication of 20 kHz at 25 °C. Complete degradation of NB was effected at pH 7 in presence of 10 mM H₂O₂ after 10 min of sonication in presence of α-Fe₂O₃ (1.0 g L⁻¹), (k = 0.58 min⁻¹) and after 25 min in case of CuO (k = 0.126 min⁻¹). α-Fe₂O₃ showed also effective degradation under the conditions of 0.1 g L⁻¹ oxide and 5.0 mM of H₂O₂, even though with a lower rate constant (0.346 min⁻¹). Sonication plays a major role in enhancing the production of hydroxyl radicals in presence of solid oxides. Hydroxyl radicals-degradation pathway is suggested and adopted to explain the differences noted in rate constants recorded on using different oxides.