Intensification of extraction of curcumin from Curcuma amada using ultrasound assisted approach: Effect of different operating parameters

Curcumin, a dietary phytochemical, has been extracted from rhizomes of Curcuma amada using ultrasound assisted extraction (UAE) and the results compared with the conventional extraction approach to establish the process intensification benefits. The effect of operating parameters such as type of solvent, extraction time, extraction temperature, solid to solvent ratio, particle size and ultrasonic power on the extraction yield have been investigated in details for the approach UAE. The maximum extraction yield as 72% was obtained in 1 h under optimized conditions of 35 °C temperature, solid to solvent ratio of 1:25, particle size of 0.09 mm, ultrasonic power of 250 W and ultrasound frequency of 22 kHz with ethanol as the solvent. The obtained yield was significantly higher as compared to the batch extraction where only about 62% yield was achieved in 8 h of treatment. Peleg’s model was used to describe the kinetics of UAE and the model showed a good agreement with the experimental results. Overall, ultrasound has been established to be a green process for extraction of curcumin with benefits of reduction in time as compared to batch extraction and the operating temperature as compared to Soxhlet extraction.     

Bio-refinery of orange peels waste: A new concept based on integrated green and solvent free extraction processes using ultrasound and microwave techniques to obtain essential oil,polyphenols and pectin

In this study, extraction of essential oil, polyphenols and pectin from orange peel has been optimized using microwave and ultrasound technology without adding any solvent but only “in situ” water which was recycled and used as solvent. The essential oil extraction performed by Microwave Hydrodiffusion and Gravity (MHG) was optimized and compared to steam distillation extraction (SD). No significant changes in yield were noticed: 4.22 ± 0.03% and 4.16 ± 0.05% for MHG and SD, respectively. After extraction of essential oil, residual water of plant obtained after MHG extraction was used as solvent for polyphenols and pectin extraction from MHG residues. Polyphenols extraction was performed by ultrasound-assisted extraction (UAE) and conventional extraction (CE). Response surface methodology (RSM) using central composite designs (CCD) approach was launched to investigate the influence of process variables on the ultrasound-assisted extraction (UAE). The statistical analysis revealed that the optimized conditions of ultrasound power and temperature were 0.956 W/cm² and 59.83 °C giving a polyphenol yield of 50.02 mg GA/100 g dm. Compared with the conventional extraction (CE), the UAE gave an increase of 30% in TPC yield. Pectin was extracted by conventional and microwave assisted extraction. This technique gives a maximal yield of 24.2% for microwave power of 500 W in only 3 min whereas conventional extraction gives 18.32% in 120 min. Combination of microwave, ultrasound and the recycled “in situ” water of citrus peels allow us to obtain high added values compounds in shorter time and managed to make a closed loop using only natural resources provided by the plant which makes the whole process intensified in term of time and energy saving, cleanliness and reduced waste water.     

Solvent extraction of cadmium and zinc from sulphate solutions: Comparison of mechanical agitation and ultrasonic irradiation

This research was conducted to evaluate the potential of ultrasonic irradiation during the solvent extraction of metals, and comparing its efficiency with a mechanically stirred system (MSSX). The simultaneous extraction of zinc and cadmium from sulphate solutions was investigated by di-(2-ethylhexyl) phosphoric acid (D2EHPA) as an organic extractant which was diluted (20%) in kerosene at the organic: aqueous phase ratio of 1:1 and the temperature of 25 °C. The influence of some critical parameters, including contact time, solution pH, ultrasonic power, and zinc/cadmium ratio were investigated on the extraction of the metals. Results show that D2EHPA selectively extract zinc rather than cadmium in both mechanically and ultrasonically mixed systems. It was also found that increase of ultrasonic power from 10 to 120 W cause a small decrease in zinc extraction; while, at low and high levels of the induced power, cadmium extraction was significantly decreased. Results also show that maximum extraction amounts of zinc (88.7%) and cadmium (68.2%) by the MSSX system occurred at the pH of 3 and the contact times of 3 and 20 min, respectively. Although capability of extraction in the ultrasonically assisted solvent extraction (USAX) system for both metals was higher, the selectivity was lower than that of MSSX system under different conditions especially in high zinc/cadmium ratios. It can be concluded that physical effects (i.e. mixing) inducing at low ultrasonic powers (below 60 W) mainly results in increasing solvent extraction rate, while the chemical actions applied at the higher powers have a negative outcome on the extraction rate particularly for cadmium.     

Effect of ultrasound on the extraction of total anthocyanins from Purple Majesty potato

This study examined anthocyanin extraction using the application of ultrasound to raw freeze dried, microwaved and raw sliced Purple Majesty potato, a new pigmented potato variety rich in anthocyanins. A 20 kHz probe was used for the sonication at 3 different amplitudes (30%, 50% and 70%) and ethanol in water at different ratios (50:50 and 70:30 v/v) was used for the extraction. Anthocyanin extraction from raw freeze dried purple potato was optimal at an ethanol:water ratio (70:30; v/v) after 5 min of ultrasonication, while the least amount of anthocyanins was extracted from raw sliced potatoes. The application of microwaves (as a pre-treatment) before the UAE resulted in an increase in the amount of anthocyanins extracted and a decrease in the amount of solvent used. Analysis of variance showed that potato form, ultrasonication time, ultrasonication amplitude and solvent ratio as well as two and three way interactions between some of these factors had a very significant effect (p < 0.000) on the amount of anthocyanins extracted.     

Kinetic modeling and optimization of maceration and ultrasound-extraction of resinoid from the aerial parts of white lady’s bedstraw (Galium mollugo L.)

In this paper, extraction of resinoid from the aerial parts of white lady’s bedstraw (Galium mollugo L.) using an aqueous ethanol solution (50% by volume) was studied at different temperatures in the absence and the presence of ultrasound. This study indicated that ultrasound-assisted extraction was effective for extracting the resinoid and gave better resinoid yields at lower extraction temperature and in much shorter time than the maceration. A phenomenological model was developed for modeling the kinetics of the extraction process. The model successfully describes the two-step extraction consisting of washing followed by diffusion of extractable substances and shows that ultrasound influences only the first step. The extraction process was optimized using response surface methodology (RMS) and artificial neural network (ANN) models. For the former modeling, the second-order polynomial equation was applied, while the second one was performed by an ANN-GA combination. The high coefficient of determination and the low MRPD between the ANN prediction and the corresponding experimental data proved that modeling the extraction process in the absence and the presence of ultrasound using ANN was more accurate than RSM modeling. The optimum extraction temperature was determined to be 80 and 40 °C, respectively for the maceration and the ultrasound-assisted extraction, ensuring the highest resinoid yield of 22.0 g/100 g in 4 h and 25.1 g/100 g in 30 min, which agreed with the yields obtained experimentally for the same time (21.7 and 25.3 g/100 g, respectively).     

Ultrasound-assisted acid hydrolysis of cellulose to chemical building blocks: Application to furfural synthesis

In this work, the use of ultrasound energy for the production of furanic platforms from cellulose was investigated and the synthesis of furfural was demonstrated. Several systems were evaluated, as ultrasound bath, cup horn and probe, in order to investigate microcrystalline cellulose conversion using simply a diluted acid solution and ultrasound. Several acid mixtures were evaluated for hydrolysis, as diluted solutions of HNO₃, H₂SO₄, HCl and H₂C₂O₄. The influence of the following parameters in the ultrasound-assisted acid hydrolysis (UAAH) were studied: sonication temperature (30 to 70 °C) and ultrasound amplitude (30 to 70% for a cup horn system) for 4 to 8 mol L⁻¹ HNO₃ solutions. For each evaluated condition, the products were identified by ultra-performance liquid chromatography with high-resolution time-of-flight mass spectrometry (UPLC-ToF-MS), which provide accurate information regarding the products obtained from biomass conversion. The furfural structure was confirmed by nuclear magnetic resonance (¹H and ¹³C NMR) spectroscopy. In addition, cellulosic residues from hydrolysis reaction were characterized using scanning electron microscopy (SEM), which contributed for a better understanding of physical-chemical effects caused by ultrasound. After process optimization, a 4 mol L⁻¹ HNO₃ solution, sonicated for 60 min at 30 °C in a cup horn system at 50% of amplitude, lead to 78% of conversion to furfural. This mild temperature condition combined to the use of a diluted acid solution represents an important contribution for the selective production of chemical building blocks using ultrasound energy.     

Temperature effects on the ultrasonic separation of fat from natural whole milk

This study showed that temperature influences the rate of separation of fat from natural whole milk during application of ultrasonic standing waves. In this study, natural whole milk was sonicated at 600 kHz (583 W/L) or 1 MHz (311 W/L) with a starting bulk temperature of 5, 25, or 40 °C. Comparisons on separation efficiency were performed with and without sonication. Sonication using 1 MHz for 5 min at 25 °C was shown to be more effective for fat separation than the other conditions tested with and without ultrasound, resulting in a relative change from 3.5 ± 0.06% (w/v) fat initially, of −52.3 ± 2.3% (reduction to 1.6 ± 0.07% (w/v) fat) in the skimmed milk layer and 184.8 ± 33.2% (increase to 9.9 ± 1.0% (w/v) fat) in the top layer, at an average skimming rate of ∼5 g fat/min. A shift in the volume weighted mean diameter (D[4,3]) of the milk samples obtained from the top and bottom of between 8% and 10% relative to an initial sample D[4,3] value of 4.5 ± 0.06 μm was also achieved under these conditions. In general, faster fat separation was seen in natural milk when natural creaming occurred at room temperature and this separation trend was enhanced after the application of high frequency ultrasound.     

Optimization of ultrasound-assisted extraction of bioactive compounds from wild garlic (Allium ursinum L.)

Ultrasound-assisted extraction was used for extraction of bioactive compounds and for production of Allium ursinum liquid extract. The experiments were carried out according to tree level, four variables, face-centered cubic experimental design (FDC) combined with response surface methodology (RSM). Temperature (from 40 to 80 °C), ethanol concentration (from 30% to 70%), extraction time (from 40 to 80 min) and ultrasonic power (from 19.2 to 38.4 W/L) were investigated as independent variables in order to obtain the optimal conditions for extraction and to maximize the yield of total phenols (TP), flavonoids (TF) and antioxidant activity of obtained extracts. Experimental results were fitted to the second order polynomial model where multiple regression and analysis of variance were used to determine the fitness of the model and optimal condition for investigated responses. The predicted values of the TP (1.60 g GAE/100 g DW), TF (0.35 g CE/100 g DW), antioxidant activity, IC₅₀ (0.71 mg/ml) and EY (38.1%) were determined at the optimal conditions for ultrasound assisted extraction: 80 °C temperature, 70% ethanol, 79.8 min and 20.06 W/L ultrasonic power. The predicted results matched well with the experimental results obtained using optimal extraction conditions which validated the RSM model with a good correlation.     

Ultrasound-assisted extraction of phenolics from wine lees: Modeling,optimization and stability of extracts during storage

The ultrasound-assisted extraction process of phenolics including anthocyanins from wine lees was modeled and optimized in this research. An ultrasound bath system with the frequency of 40 kHz was used and the acoustic energy density during extraction was identified to 48 W/L. The effects of extraction time, extraction temperature, solvent-to-solid ratio and the solvent composition on the extraction yields of total phenolics and total anthocyanins were taken into account. The extraction process was simulated and optimized by means of artificial neural network (ANN) and genetic algorithm (GA). The constructed ANN models were accurate to predict the extraction yields of both total phenolics and total anthocyanins according to the statistical analysis. Meanwhile, the input space of the ANN models was optimized by GA, so as to maximize the extraction yields. Under the optimal conditions, the experimental yields of total phenolics and total anthocyanins were 58.76 and 6.69 mg/g, respectively, which agreed with the predicted values. Furthermore, more amounts of total phenolics and total anthocyanins were extracted by ultrasound at the optimal conditions than by conventional maceration.On the other hand, the stability of phenolics in the liquid extracts obtained from ultrasound-assisted extraction during storage was evaluated. After 30-day storage, the total phenolic contents in extracts stored at 4 °C and 20 °C decreased by 12.5% and 12.1%, respectively. Moreover, anthocyanins were more stable at 4 °C while tartaric esters and flavonols exhibited a better stability at 20 °C. Overall, the loss of phenolics during storage found in this study could be acceptable.     

Trace determination of safranin O dye using ultrasound assisted dispersive solid-phase micro extraction: Artificial neural network-genetic algorithm and response surface methodology

In this study, ultrasound assisted dispersive solid-phase micro extraction combined with spectrophotometry (USA-DSPME-UV) method based on activated carbon modified with Fe₂O₃ nanoparticles (Fe₂O₃-NPs-AC) was developed for pre-concentration and determination of safranin O (SO). It is known that the efficiency of USA-DSPME-UV method may be affected by pH, amount of adsorbent, ultrasound time and eluent volume and the extent and magnitude of their contribution on response (in term of main and interaction part) was studied by using central composite design (CCD) and artificial neural network-genetic algorithms (ANN-GA). Accordingly by adjustment of experimental conditions suggested by ANN-GA at pH 6.5, 1.1 mg of adsorbent, 10 min ultrasound and 150 μL of eluent volume led to achievement of best operation performance like low LOD (6.3 ng mL⁻¹) and LOQ (17.5 ng mL⁻¹) in the range of 25–3500 ng mL⁻¹. In following stage, the SO content in real water and wastewater samples with recoveries between 93.27–99.41% with RSD lower than 3% was successfully determined.     

Optimization of ultrasound-assisted extraction of total monomeric anthocyanin (TMA) and total phenolic content (TPC) from eggplant (Solanum melongena L.) peel

The present study describes the extraction of total monomeric anthocyanin (TMA) and total phenolic content (TPC) from eggplant peel using ultrasonic treatments and methanol and 2-propanol as extraction solvents. The extraction yields were optimized by varying the solvent concentration, ultrasonic frequency, temperature and time of ultrasonic treatment. Box–Behnken design was used to investigate the effect of process variables on the ultrasound-assisted extraction. The results showed that for TPC extraction the optimal condition were obtained with a methanol concentration of 76.6%, 33.88 kHz ultrasonic frequency, a temperature of 69.4 °C and 57.5 min extraction time. For TMA the optimal condition were the following: 54.4% methanol concentration, 37 kHz, 55.1 °C and process time of 44.85 min.     

Effect of ultrasound on the supercritical CO2 extraction of bioactive compounds from dedo de moça pepper (Capsicum baccatum L. var. pendulum)

Extracts with bioactive compounds were obtained from the red pepper variety “dedo de moça” (Capsicum baccatum L. var. pendulum) through supercritical fluid extraction with carbon dioxide assisted by ultrasound (SFE-US). The process was tested at pressures of 15, 20 and 25 MPa; temperatures of 40, 50 and 60 °C, and ultrasonic powers of 200, 400 and 600 W applied during 40, 60 and 80 min of extraction. The CO₂ mass flow rate was fixed at 1.7569 × 10⁻⁴ kg/s. Global yield, phenolic content, antioxidant capacity and capsaicinoid concentration were evaluated in the extracts. The application of ultrasound raised the global extraction yield of SFE up to 45%. The phenolic content of the extract increased with the application of higher ultrasound power and radiation time. The capsaicinoid yield was also enhanced with ultrasound up to 12%. However, the antioxidant capacity did not increase with the ultrasound application. The BET-based model and the broken and intact cell model fitted well to the kinetic SFE curves. The BET-based model with three adjustable parameters resulted in the best fits to the experimental data. Field emission scanning electron microscopy (FESEM) images showed that SFE disturbed the vegetable matrix, releasing particles from the inner region of the plant cells to their surface. When the ultrasound was applied this effect was more pronounced. On the other hand, cracks, fissures or any sign of rupture were not identified on the sample surface.     

Effects of processing parameters in the sonic assisted water extraction (SAWE) of 6-gingerol

The use of water in subcritical conditions for extraction has several drawbacks. These include the safety features, higher production costs and possible degradation of the bioactive compounds. To overcome these problems, sonic energy and an entrainer were used as external interventions to decrease the polarity of water at milder operating conditions. The effect of low (28 kHz) and high (800 kHz) frequencies of sonication in the extraction of the main ginger bioactive compound (6-gingerol) were compared. Six parameters were studied: mean particle size (MPS, mm), time of extraction, applied power, sample to solvent ratio (w/v), temperature of extraction, and the percentage of entrainer. The optimum conditions for high frequency SAWE prototype were MPS 0.89–1.77 mm, 45 min, 40 W applied power, 1:30 (w/v), 45 °C, and 15% of ethanol as entrainer. Two-way analysis of variance (ANOVA) gave the most significant parameter, which was power with F (1, 45.07), p < 2.50 × 10⁻⁹. Although the effect of low frequency was stronger than high frequency, at the optimum conditions of the sample to solvent ratio 1:30 (w/v) with 700 mL solvent and temperature 45 °C, the concentration and recovery of 6-gingerol from high frequency of SAWE prototype was 2.69 times higher than at low frequency of SAWE. It was found that although the effects of high frequency (800 kHz) were negligible in other studies, it could extract suitable compounds, such as 6-gingerol, at lower temperature. Therefore, the effects of sonication, which cause an enlargement in the cell wall of the ginger plant matrix, were observed using a Scanning Electron Microscope (SEM). It was found that the applied power of sonication was the most significant parameter compared to the other parameters.     

Green ultrasound-assisted extraction of carotenoids from pomegranate wastes using vegetable oils

The objective of this work was to develop a new process for pomegranate peels application in food industries based on ultrasound-assisted extraction of carotenoids using different vegetable oils as solvents. In this way, an oil enriched with antioxidants is produced. Sunflower oil and soy oil were used as alternative solvents and the effects of various parameters on extraction yield were studied. Extraction temperature, solid/oil ratio, amplitude level, and extraction time were the factors investigated with respect to extraction yield. Comparative studies between ultrasound-assisted and conventional solvent extraction were carried out in terms of processing procedure and total carotenoids content. The efficient extraction period for achieving maximum yield of pomegranate peel carotenoids was about 30 min. The optimum operating conditions were found to be: extraction temperature, 51.5 °C; peels/solvent ratio, 0.10; amplitude level, 58.8%; solvent, sunflower oil. A second-order kinetic model was successfully developed for describing the mechanism of ultrasound extraction under different processing parameters.     

Kinetic improvement of olive leaves’ bioactive compounds extraction by using power ultrasound in a wide temperature range

In this study, the effect of temperature and ultrasonic application on extraction kinetics of polyphenols from dried olive leaf was investigated. Conventional (CVE) and ultrasonic-assisted extraction (UAE) were performed at 10, 20, 30, 50 and 70 °C using water as solvent. Extracts were characterized by measuring the total phenolic content, the antioxidant capacity and the oleuropein content (HPLC–DAD/MS–MS). Moreover, Naik’s model was used to mathematically describe the extraction kinetics. The experimental results showed that phenolic extraction was faster in UAE (ultrasonic-assisted extraction) than in CVE (conventional extraction), being extraction kinetics satisfactorily described using Naik model (include VAR > 98%). Besides, the total phenolic content, the antioxidant capacity and the oleuropein content were significantly (p < 0.05) improved by increasing the temperature in both CVE and UAE. Oleuropein content reached 6.57 ± 0.18 being extracted approximately 88% in the first minute for UAE experiments.     

Impact of ultrasound on solid–liquid extraction of phenolic compounds from maritime pine sawdust waste. Kinetics,optimization and large scale experiments

Maritime pine sawdust, a by-product from industry of wood transformation, has been investigated as a potential source of polyphenols which were extracted by ultrasound-assisted maceration (UAM). UAM was optimized for enhancing extraction efficiency of polyphenols and reducing time-consuming. In a first time, a preliminary study was carried out to optimize the solid/liquid ratio (6 g of dry material per mL) and the particle size (0.26 cm²) by conventional maceration (CVM). Under these conditions, the optimum conditions for polyphenols extraction by UAM, obtained by response surface methodology, were 0.67 W/cm² for the ultrasonic intensity (UI), 40 °C for the processing temperature (T) and 43 min for the sonication time (t). UAM was compared with CVM, the results showed that the quantity of polyphenols was improved by 40% (342.4 and 233.5 mg of catechin equivalent per 100 g of dry basis, respectively for UAM and CVM). A multistage cross-current extraction procedure allowed evaluating the real impact of UAM on the solid–liquid extraction enhancement. The potential industrialization of this procedure was implemented through a transition from a lab sonicated reactor (3 L) to a large scale one with 30 L volume.     

Ultrasound assisted enzymatic pre-treatment of high fat content dairy wastewater

This paper illustrates the application of ultrasound in a dairy waste water treatment for the removal of fat using enzyme as a catalyst. Lipase Z was used to perform the enzymatic pre-hydrolysis of a synthetic dairy wastewater containing around 2000 mg/L of fat content coupled with ultrasound irradiation. Different process parameters like effect of enzyme loading, temperature, ultrasound power, frequency, duty cycle and speed of agitation are optimized. The maximum hydrolysis of 78% is achieved at 0.2% enzyme loading (w/v), 30 °C temperature, 165 W of ultrasonication power at 25 kHz and 66% duty cycle. It was observed that the enzymatic pre-hydrolysis under the influence of ultrasound drastically reduces the reaction time from 24 h to 40 min as compared to conventional stirring with improved yield.     

Aqueous two-phase system coupled with ultrasound for the extraction of lignans from seeds of Schisandra chinensis (turcz.) Baill

In this study the potential use of an aqueous two phase system (ATPS) coupled with ultrasound for the extraction of lignans from Schisandra chinensis seeds was evaluated and optimized using response surface methodology (RSM). The main bioactive components, schizandrin (SA), schisantherin A (SAA) and deoxyschizandrin (DSA) were selected as markers. The partitioning behavior of lignans in different salt-types of ATPS was compared. The optimization ATPS of 25% (w/w) (NH₄)₂SO₄ and 19% (w/w) ethanol were selected based on their higher upper phase partitioning coefficient (>74) and the recovery (>93%) for three markers. Using the optimized ATPS solvent, the RMS results showed 20:1 of solvent:solid, 800 W and 61.1 min were the optimal ultrasound assisted extraction conditions, under which 13.10 mg/g SA, 1.87 mg/g SAA and 1.84 mg/g DSA were recovered in the upper phase, whereas the wasted stigmas accumulated in the lower phase. Compared with 80% ethanol (v/v) ultrasonic extraction, similar yields were obtained, but the present method exhibited higher extraction purity for the selective extraction of lignans from S. chinensis seeds.     

Effects of various factors of ultrasonic treatment on the extraction recovery of drugs from fish tissues

In the present research, a combined extraction method of ultrasound-assisted extraction (UAE) in conjunction with solid phase extraction (SPE) was applied to isolation and enrichment of selected drugs (metoprolol, ticlopidine, propranolol, carbamazepine, naproxen, acenocumarol, diclofenac, ibuprofen) from fish tissues. The extracted analytes were separated and determined by ultra-high performance liquid chromatography with UV detection (UHPLC–UV) technique. The selectivity of the developed UHPLC–UV method was confirmed by comparison with ultra-high performance liquid chromatography–tandem mass spectrometry (UHPLC–MS/MS) analysis.The important parameters, such as composition of type and pH of extraction solvent, solid/liquid rate volume of extraction solvent and number of extraction cycles were studied. The ultrasonic parameters, such as time, power and temperature of the process were optimized by using a half-fraction factorial central composite design (CCD). The mixture of 10 mL of methanol and 7 mL of water (pH 2.2) (three times) was chosen for the extraction of selected drug from fish tissues. The results showed that the highest recoveries of analytes were obtained with an extraction temperature of 40 °C, ultrasonic power of 300 W, extraction time of 30 min.Under the optimal conditions, the linearity of method was 0.12–5.00 μg/g. The determination coefficients (R²) were from 0.979 to 0.998. The limits of detection (LODs) and limits of quantification (LOQs) for the extracted compounds were 0.04–0.17 μg/g and 0.12–0.50 μg/g, respectively. The recoveries were between 85.5% and 115.8%.     

Ultrasound-assisted extraction of polysaccharides from Rhododendron aganniphum: Antioxidant activity and rheological properties

In this study, we aimed to optimize the extraction of polysaccharides from the leaves of Rhododendron aganniphum and investigate its rheological properties and antioxidant activity. After optimizing the operating parameters using a Box-Behnken design (BBD), the results showed that the optimal ultrasound-assisted extraction conditions were as follows: extraction temperature, 55 °C; liquid-solid ratio, 25:1; extraction time, 2.2 h; and ultrasound treatment power, 200 W. The optimized experimental yield of polysaccharides by ultrasound-assisted extraction (PUAE) was 9.428%, higher than that obtained by hot water extraction (PHWE) for 12 h at the same liquid-solid ratio and extraction temperature. In the in vitro antioxidant activity tests, PUAE had higher positive radical scavenging activity for hydroxyl, superoxide and 1,1-diphenyl-2-picrylhydrazyl (DPPH) radicals than PHWE. However, PUAE and PHWE solutions had similar intermolecular interactions in the steady-shear flow and dynamic viscoelasticity tests, resulting in similar macroscopic behaviour. With respect to the apparent viscosity, storage modulus (G′) and loss modulus (G″) of PUAE were lower at the same shear rate or angular frequency. All PUAE solutions exhibited non-Newtonian shear-thinning pseudoplastic behaviour that was accurately described by the Carreau model but was better fit by the power-law model at high shear rates (≥1/s), which demonstrated that the variation in the apparent viscosity dependence was greater at higher concentrations and shear rates. The G′ and G″ of the solutions increased as the experimental frequency increased from 0.05 to 500 rad/s under all experimental concentrations, and the modulus crossover point decreased gradually with increasing PUAE concentration. The above results demonstrated that the ultrasound-assisted extraction methods gave a higher yield of polysaccharides from the leaves of R. aganniphum with a shorter extraction time than the hot water extraction method, which could affect the apparent viscosity and dynamic viscoelasticity. PUAE presented good radical scavenging activity for DPPH, superoxide and hydroxyl radicals in vitro and could be used as a natural antioxidant in the food and medical industries.