卟啉锡敏化TiO_2纳米管的光催化活性和光电性能

制备了反-二羟基-5,10,15,10-四苯基卟啉锡敏化的TiO2纳米管,并以对硝基苯酚为模型污染物,对其在可见光照射下的光催化活性进行了研究。同时,将卟啉锡敏化的TiO2纳米粒子作为参照物,探讨了形貌对催化剂光催化活性的影响。实验结果表明,卟啉锡的引入可以明显地增强TiO2纳米管的可见光催化活性。与TiO2纳米粒子相比,卟啉锡对TiO2纳米管的敏化作用更加显著,表明催化剂的形貌在光催化过程中具有重要作用。此外,我们还考察了卟啉锡敏化的TiO2纳米管的光电化学行为,并与其光催化活性相关联。最后,对卟啉锡的敏化机理进行了初步的探讨。     

Cu/Ni助催化剂对TiO2光催化制取苯酚性能的影响

以TiO₂纳米粒子为主催化剂, 采用“浸渍-还原法”构筑了铜、镍共负载的二氧化钛基光催化系统。以苯为起始原料, H₂O₂为氧化剂, 研究了Cu/Ni助催化剂对TiO₂可见光催化制取苯酚性能的影响并对Cu/Ni助催化剂的作用机制进行了探讨。结果表明, 在可见光照射下, 纯TiO₂纳米粒子对苯氧化制取苯酚反应没有催化活性。铜、镍的引入可以明显地增强TiO₂可见光催化制取苯酚的活性。当使用负载有铜、镍的TiO₂作为催化剂时, 苯酚的产率可达到18%。结果还表明Cu、Ni之间存在着很强的协同作用。在该协同作用下, Cu、Ni共负载的TiO₂纳米粒子表现出了较单一金属负载的TiO₂纳米粒子高得多的光催化活性。     

Cu/Ni助催化剂对TiO2光催化制取苯酚性能的影响

以TiO₂纳米粒子为主催化剂,采用"浸渍-还原法"构筑了铜、镍共负载的二氧化钛基光催化系统。以苯为起始原料,H₂O₂为氧化剂,研究了Cu/Ni助催化剂对TiO₂可见光催化制取苯酚性能的影响并对Cu/Ni助催化剂的作用机制进行了探讨。结果表明,在可见光照射下,纯TiO₂纳米粒子对苯氧化制取苯酚反应没有催化活性。铜、镍的引入可以明显地增强Ti₀₂可见光催化制取苯酚的活性。当使用负载有铜、镍的TiO₂作为催化剂时,苯酚的产率可达到18%。结果还表明Cu、Ni之间存在着很强的协同作用。在该协同作用下,Cu、Ni共负载的TiO₂纳米粒子表现出了较单一金属负载的TiO₂纳米粒子高得多的光催化活性。     

CdS/TiO2纳米管复合结构的制备与光电性能研究

利用阳极氧化法在钛金属基体表面制备一层TiO₂纳米管阵列薄膜, 然后通过水热反应在TiO₂纳米管上负载CdS纳米粒子, 形成CdS/TiO₂纳米管的复合结构。利用SEM、XRD、XPS、UV-Vis等手段对其形貌和结构进行表征。进一步考察了CdS/TiO₂纳米管的光电性能和光催化活性, 结果表明, 相比于TiO₂纳米管, CdS/TiO₂纳米管复合结构在紫外光和可见光下都具有更好的光催化活性及光电性能。     

氟掺杂TiO2纳米管的可见光催化活性及第一性原理计算

作为光催化技术的核心, 提高TiO₂的光催化活性和对可见光的利用率是当前光催化研究中最重要的研究课题. 为了提高TiO₂纳米管的可见光催化活性, 采用化学气相沉积法对TiO₂纳米管进行了氟掺杂. 扫描电子显微镜(SEM)结果表明退火温度对于TiO₂纳米管的形貌完整性有较大影响, 当样品在550和700 °C下退火, 氟掺杂TiO₂纳米管结构受损; X射线衍射(XRD)分析表明氟掺杂对TiO₂由锐钛矿相转化为金红石相有阻碍作用; X射线光电子能谱(XPS)测试表明化学气相沉积能有效地对TiO₂纳米管进行非金属掺杂, 且该方法安全、操作简单. 氟掺杂TiO₂纳米管对甲基橙有较高的可见光催化降解活性. 第一性原理计算结果表明氟掺杂对TiO₂带隙无显著影响, 费米能级附近的F 2p轨道电子位于价带底部, 与O 2p交联作用较小, 因此对TiO₂光吸收带边影响不大. 氟掺杂能促进表面氧空穴的产生, 增加表面酸度与Ti³⁺, 有利于减少电子-空穴复合率, 从而提高其光催化活性.     

TiO2-双亲共聚物复合纳米粒子的合成与紫外光敏特性

用偶联剂乙烯基三乙氧基硅烷改性纳米粒子TiO₂, 应用超声技术将TiO₂ 纳米粒子分散在甲醇介质中, 然后用苯乙烯(ST)原位聚合包封, 再用丙烯酰胺或乙烯基吡咯烷酮(VP)共聚, 两步原位分散聚合得到了有机聚合物为壳、TiO₂为核的有机/无机复合粒子. 用红外光谱、紫外-可见光谱、透射电子显微镜等检测手段进行表征. 结果显示: 由于双亲共聚物对TiO₂纳米粒子的敏化作用, 紫外-可见光谱图上两种纳米复合粒子的最大吸收峰均有明显红移, 并且吸收光谱的范围扩大了, 其中尤以TiO₂/(PST-co-PVP)为甚. 意味着光敏化活性的提高, 特别是在可见光谱的范围内. 这种情形对宽带隙半导体材料如TiO₂纳米粒子的光催化特性是有利的, 表明这类材料的应用空间得到了拓展.     

TiO2-双亲共聚物复合纳米粒子的合成与紫外光敏特性

用偶联剂乙烯基三乙氧基硅烷改性纳米粒子TiO₂, 应用超声技术将TiO₂ 纳米粒子分散在甲醇介质中, 然后用苯乙烯(ST)原位聚合包封, 再用丙烯酰胺或乙烯基吡咯烷酮(VP)共聚, 两步原位分散聚合得到了有机聚合物为壳、TiO₂为核的有机/无机复合粒子. 用红外光谱、紫外-可见光谱、透射电子显微镜等检测手段进行表征. 结果显示: 由于双亲共聚物对TiO₂纳米粒子的敏化作用, 紫外-可见光谱图上两种纳米复合粒子的最大吸收峰均有明显红移, 并且吸收光谱的范围扩大了, 其中尤以TiO₂/(PST-co-PVP)为甚. 意味着光敏化活性的提高, 特别是在可见光谱的范围内. 这种情形对宽带隙半导体材料如TiO₂纳米粒子的光催化特性是有利的, 表明这类材料的应用空间得到了拓展.     

Bi2WO6/TiO2纳米管异质结构复合材料的多模式下的光催化活性比较

以TiO₂纳米管为模板,采用多组分自组装结合水热法制备Bi₂WO₆/TiO₂纳米管异质结构复合材料。通过多种技术如X射线衍射（XRD）,X射线光电子能谱（XPS）,N₂吸附-脱附,扫描电镜（SEM）,高分辨透射电镜（HRTEM）和紫外可见漫反射吸收光谱（UV-Vis DRS）考察所制备样品的组成、结构、形貌、光吸收和电子性质。Bi₂WO₆纳米片或纳米粒子分布在TiO₂纳米管上,形成异质结构。随后,通过在紫外、可见和微波辅助光催化模式下降解染料罗丹明B（RhB）来评价复合催化剂的光催化活性。与TiO₂纳米管和Bi₂WO₆相比,Bi₂WO₆/TiO₂-35纳米管在多模式下表现出更优异的光催化活性。与紫外和可见降解模式相比,Bi₂WO₆/TiO₂-35纳米管在微波辅助光催化模式下对RhB的降解效率最高。这种增强的光催化活性源于适量Bi₂WO₆的引入、纳米管独特的形貌特征和降解模式所引起的增强的量子效率。降解过程中的活性物种被证明是h⁺,·OH和·O₂^-自由基。而且,在微波辅助光催化模式下,可产生更多的·OH和·O₂^-自由基。     

Bi2WO6/TiO2纳米管异质结构复合材料的多模式下的光催化活性比较

以TiO₂纳米管为模板,采用多组分自组装结合水热法制备Bi₂WO₆/TiO₂纳米管异质结构复合材料。通过多种技术如X射线衍射（XRD）,X射线光电子能谱（XPS）,N₂吸附脱附,扫描电镜（SEM）,高分辨透射电镜（HRTEM）和紫外可见漫反射吸收光谱（UV-Vis DRS）考察所制备样品的组成、结构、形貌、光吸收和电子性质。Bi₂WO₆纳米片或纳米粒子分布在TiO₂纳米管上,形成异质结构。随后,通过在紫外、可见和微波辅助光催化模式下降解染料罗丹明B（RhB）来评价复合催化剂的光催化活性。与TiO₂纳米管和Bi₂WO₆相比,Bi₂WO₆/TiO₂-35纳米管在多模式下表现出更优异的光催化活性。与紫外和可见降解模式相比,Bi₂WO₆/TiO₂-35纳米管在微波辅助光催化模式下对RhB的降解效率最高。这种增强的光催化活性源于适量Bi₂WO₆的引入、纳米管独特的形貌特征和降解模式所引起的增强的量子效率。降解过程中的活性物种被证明是h⁺,·OH和·O₂^-自由基。而且,在微波辅助光催化模式下,可产生更多的·OH和·O₂^-自由基。     

阳极氧化法制备TiO2纳米管及其光催化性能

纳米TiO₂对诸多环境污染物有显著的光催化降解作用,光催化已发展成为新型环境污染治理技术。本文采用阳极氧化法制备出TiO₂纳米管,对比了四种电解液组成(A氟化铵+硫酸铵+水;B氟化铵+硫酸铵+乙酸+水;C氟化铵+硫酸铵+甘油+水;D氢氟酸+二甲基亚砜(DMOS)+乙醇)对催化剂表面形貌及光催化性能的影响。结果表明,电解液A和C都制备出了形貌清晰的TiO₂纳米管,管径约为60~74 nm。样品经400 ℃煅烧,TiO₂晶型主要为锐钛矿相;经500 ℃煅烧,出现少量金红石相;经700 ℃煅烧,晶型全部为金红石相。具有良好形貌的TiO₂纳米管同时具有良好的紫外光吸收能力。当亚甲基蓝初始浓度为10 mg·L^-1,经500 ℃煅烧的TiO₂纳米管光催化活性最佳,光照30 min亚甲基蓝的降解率达89.98%。亚甲基蓝光催化降解反应符合一级反应动力学,反应速率常数为0.079 30。     

Crystal growth, structure determination, and optical properties of new potassium-rare-earth silicates K3RESi2O7 (RE=Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu)

Single crystals of K₃RESi₂O₇ (RE=Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu) were grown from a potassium fluoride flux. Two different structure types were found for this series. Silicates containing the larger rare earths, RE=Gd, Tb, Dy, Ho, Er, Tm, Yb crystallize in a structure K₃RESi₂O₇ that contains the rare-earth cation in both a slightly distorted octahedral and an ideal trigonal prismatic coordination environment, while in K₃LuSi₂O₇, containing the smallest of the rare earths, lutetium is found solely in an octahedral coordination environment. The structure of K₃LuSi₂O₇ crystallizes in space group P6₃/mmc with a=5.71160(10) Å and c=13.8883(6) Å. The structures containing the remaining rare earths crystallize in the space group P6₃/mcm with the lattice parameters of a=9.9359(2) Å, c=14.4295(4) Å, (K₃GdSi₂O₇); a=9.88730(10) Å, c=14.3856(3) Å, (K₃TbSi₂O₇); a=9.8673(2) Å, c=14.3572(4) Å, (K₃DySi₂O₇); a=9.8408(3) Å, c=14.3206(6) Å, (K₃HoSi₂O₇); a=9.82120(10) Å, c=14.2986(2) Å, (K₃ErSi₂O₇); a=9.80200(10) Å, c=14.2863(4) Å, (K₃TmSi₂O₇); a=9.78190(10) Å, c=14.2401(3) Å, (K₃YbSi₂O₇). The optical properties of the silicates were investigated and K₃TbSi₂O₇ was found to fluoresce in the visible.     

Li_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3,Na_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3的离子交换研究

研究了在不同温度下的NaNO3和AgNO3水溶液中Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3离子交换行为.实验表明Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3均显示出了高选择性与Na+和Ag+进行离子交换的特征,且对Ag+的选择性高于Na+.升高温度可显著提高Ag/Li和Ag/Na的交换反应速度.     

The crystal chemistry of Bi6TP2O15+x, T=Fe, Ni, Zn: Isomorphism and polymorphism, structural relationship to Bi6TiP2O16

The crystal structures of compounds with nominal compositions Bi₆FeP₂O_15+x (I), Bi₆NiP₂O_15+x (II) and Bi₆ZnP₂O_15+x (III) were determined from single-crystal X-ray diffraction data. They are monoclinic, space group I2, Z=2. The lattice parameters for (I) are a=11.2644(7), b=5.4380(3), c=11.1440(5) Å, β=96.154(4)°; for (II) a=11.259(7), b=5.461(4), c=11.109(7) Å, β=96.65(1)°; for (III) a=19.7271(5), b=5.4376(2), c=16.9730(6) Å, β=131.932(1)°. Least squares refinements on F² converged for (I) to R1=0.0554, wR₂=0.1408; for (II) R₁=0.0647, wR₂=0.1697; for (III) R₁=0.0385, wR₂=0.1023. The crystals are complexly twinned by 2-fold rotation about , by inversion and by mirror reflection. The structures consist of edge-sharing articulations of OBi₄ tetrahedra forming layers in the a-c plane that then continue by edge-sharing parallel to the b-axis. The three-dimensional networks are bridged by Fe and Ni octahedra in (I) and (II) and by Zn trigonal bipyramids in (III) as well as by oxygen atoms of the PO₄ moieties. Bi also randomly occupies the octahedral sites. Oxygen vacancies exist in the structures of the three compounds due to required charge balances and they occur in the octahedral coordination polyhedron of the transition metal. In compound (III), no positional disorder in atomic sites is present. The Bi-O coordination polyhedra are trigonal prisms with one, two or three faces capped. Magnetic susceptibility data for compound (I) were obtained between 4.2 and 350 K. Between 4.2 and 250 K it is paramagnetic, μ_eff=6.1 μ_B; a magnetic transition occurs above 250 K.     

Near infrared study of aqueous rare-earth ethylsulfates

The near infrared spectra of aqueous solutions of the ethylsulfates of La, Nd, Gd, Tb, Er, Yb, Lu, Y, and Na have been determined from about 0.2 mol-dm^–3 to nearly saturation. The extinction coefficients of water have been calculated taking into account the absorption of ethylslfate anions determined in separate experiments. Their values appeared to be nearly the same as that of pure water. The relative contents of free OH groups in 0.5 and 0.7M solutions have been estimated from the absorbances at 1160 nm. They were lower in solutions of the heavy rare-earth ethylsulfates (Tb, Er, Yb, Lu) than in equimolar solutions of the lighter ones (La, Nd), confirming our previous view that secondary hydration of the heavy trivalent rare-earth cations is distinctly stronger than that of the lighter ones. A comparison of the spectra of these aqueous ethylsulfates with those of perchlorates shows that the structure-breaking ability of the C₂H₅SO ₄ ^– ion is much smaller than that of perchlorate anion.     

电感耦合等离子体光谱法(ICP-AES)测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量

针对银精矿样品复杂,难消解的特点,研究了不同酸溶法和碱熔法对样品的消解情况,建立了硝酸,盐酸,氢氟酸,高氯酸消解银精矿的方法。根据元素灵敏度和抗干扰性,选定各元素的测定波长。通过酸溶样和碱熔样测定结果比对,验证了方法准确性。建立了四酸消解-电感耦合等离子体光谱法测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的方法,元素的线性相关系数均在0.9999以上。通过共存元素干扰实验,确定了银精矿中高含量元素(铜、铅、锌、铁、锑、铋等)对测定元素结果没有影响。方法检出限：Cu 0.0063 mg/L, Pb 0.0159 mg/L ,Zn 0.0090 mg/L,As 0.0192 mg/L, Cd 0.0093 mg/L ,Ca 0.0084 mg/L, Mg 0.0075 mg/L, Mn 0.0081 mg/L。测定下限：Cu 0.0105mg/L,Pb 0.0265 mg/L, Zn 0.0150 mg/L, As 0.0320 mg/L, Cd 0.0155 mg/L, Ca 0.0140 mg/L, Mg 0.0125 mg/L,Mn 0.0135 mg/L。3个样品的相对标准偏差在0.87%~3.56%之间,加标回收率在95.00%~103.56%之间。方法流程短,操作简单,快速,灵敏度和再现性高,结果准确可靠,可以满足银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的测定。     

Structural studies of five layer Aurivillius oxides: A2Bi4Ti5O18 (A=Ca, Sr, Ba and Pb)

The room temperature structures of the five layer Aurivillius phases A₂Bi₄Ti₅O₁₈ (A=Ca, Sr, Ba and Pb) have been refined from powder neutron diffraction data using the Rietveld method. The structures consist of [Bi₂O₂]²⁺ layers interleaved with perovskite-like [A₂Bi₂Ti₅O₁₆]²⁻ blocks. The structures were refined in the orthorhombic space group B2eb (SG. No. 41), Z=4, and the unit cell parameters of the oxides are a=5.4251(2), b=5.4034(1), c=48.486(1); a=5.4650(2), b=5.4625(3), c=48.852(1); a=5.4988(3), b=5.4980(4), c=50.352(1); a=5.4701(2), b=5.4577(2), c=49.643(1) for A=Ca, Sr, Ba and Pb, respectively. The structural features of the compounds were found similar to n=2-4 layers bismuth oxides. The strain caused by mismatch of cell parameter requirements for the [Bi₂O₂]²⁺ layers and perovskite-like [A₂Bi₂Ti₅O₁₆]²⁻ blocks were relieved by tilting of the TiO₆ octahedra. Variable temperature synchrotron X-ray studies for Ca and Pb compounds showed that the orthorhombic structure persisted up to 675 and 475 K, respectively. Raman spectra of the compounds are also presented.     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.     

B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃-Bi₂O₃-ZnO-Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1 350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1 364,介电损耗低至1.2%。     

The Phase Relations in the System In2O3–TiO2–MgO at 1100 and 1350°C

The phase relations in the system In₂O₃–TiO₂–MgO at 1100 and 1350°C are determined by a classical quenching method. In this system, there are four pseudobinary compounds, In₂TiO₅, MgTi₂O₅ (pseudobrookite type), MgTiO₃ (ilmenite type), and Mg₂TiO₄ (spinel type) at 1100°C. At 1350°C, in addition to these compounds there exist a spinel-type solid solution Mg_2−xIn_2xTi_1−xO₄ (0≤x≤1) and a compound In₆Ti₆MgO₂₂ with lattice constants a=5.9236(7) Å, b=3.3862(4) Å, c=6.3609(7) Å, β=108.15(1)°, and q=0.369, which is isostructural with the monoclinic In₃Ti₂FeO₁₀ in the system In₂O₃–TiO₂–MgO. The relation between the lattice constants of the spinel phase and the composition nearly satisfies Vegard's law. In₆Ti₆MgO₂₂ extends a solid solution range to In₂₀Ti₁₇Mg₃O₆₇ with lattice constants of a=5.9230(5) Å, b=3.3823(3) Å, c=6.3698(6) Å, β=108.10(5)°, and q=0.360. The distributions of constituent cations in the solid solutions are discussed in terms of their ionic radius and site preference effect.     

Solid-solid interactions in pure and Li2O-doped manganese and magnesium mixed oxides system

The solid-solid interactions between manganese and magnesium oxides in absence and in presence of small amounts of Li₂O have been investigated. The molar ratios between manganese and magnesium oxides in the form of Mn₂O₃ and MgO were varied between 0.05:1 to 0.5:1. The mixed solids were calcined in air at 400-1000°C. The techniques employed were DTA, XRD and H₂O₂ decomposition at 20-40°C.The results obtained revealed that solid-solid interactions took place between the reacting solids at 600-1000°C yielding magnesium manganates (Mg₂MnO₄, Mg₆MnO₈, MgMnO₄ besides unreacted portions of MgO, Mn₂O₃ and Mn₃O₄). Li₂O-doping (0.75-6 mol%) of the investigated system followed by calcination at 600 and 800°C decreased progressively the intensity of the diffraction lines of Mn₂O₃ (Bixbyite) with subsequent increase in the lattice parameter 'a' of MgO to an extent proportional to the amount of Li₂O added. This finding might suggest that the doping process enhanced the dissolution of Mn₂O₃ in MgO forming solid solution. This treatment led also to the formation of Li₂MnO₃. Furthermore, the doping with 3 and 6 mol% Li₂O conducted at 800°C resulted in the conversion of Mn₂O₃ into Mn₃O₄, a process that took place at 1000°C in absence of Li₂O. The produced Li₂MnO₃ phase remained stable by heating at up to 1000°C. Furthermore, Li₂O doping of the investigated system at 400-1000°C resulted in a progressive measurable increase in the particle size of MgO.The catalytic activity measurements showed that the increase in the molar ratio of Mn₂O₃ in the samples precalcined at 400-800°C was accompanied by a significant increase in the catalytic activity of the treated solids. The maximum increase in the catalytic activity expressed as reaction rate constant measured at 20°C (k _20°C) attained 3.14, 2.67 and 3.25-fold for the solids precalcined at 400, 600 and 800°C, respectively. Li₂O-doping of the samples having the formula 0.1 Mn₂O₃/MgO conducted at 400-600°C brought a progressive significant increase in its catalytic activity. The maximum increase in the value of k _20°C due to Li₂O attained 1.93 and 2.75-fold for the samples preheated at 400 and 600°C, respectively and opposite effect was found for the doped samples preheated at 800°C.This revised version was published online in November 2005 with corrections to the Cover Date.