A chemiluminescence method for the detection of electrochemically generated H2O2 and ferryl porphyrin

Electrochemical formation of H2O2 and the subsequent ferryl porphyrin were examined by measuring luminol chemiluminescence and absorption spectrum using flow-injection method. Emission was observed under the cathodic potential (0.05 V at pH 2.0 and -0.3 V at pH 11.0) by the electrochemical reduction of buffer electrolytes solution but no emission was observed at anodic potentials. Fe(III)TMPyP solution was added at the down stream of the working electrode and was essential for the emission. Removal of dissolved O2 resulted in the decrease of emission intensity by more than 70%. In order to examine the lifetime of reduced active species, delay tubes were used in between working electrode and Fe(III)TMPyP inlet. Experimental results suggested the active species were stable for quite long. The emission was quenched considerably (>90%) when hydroperoxy catalase was added at the down stream of the working electrode whereas SOD had little effect. Significant inhibition of the emission by the addition of alkene at the down stream of the Fe(III)TMPyP inlet was considered as evidence of oxo-ferryl formation. The spectra at reduction potential under aerated condition were shifted to the longer wavelength (>430 nm) compared to the original spectrum of Fe(III)TMPyP (422 nm). All the spectra were perfectly reproduced by a combination of Fe(III)TMPyP and O=Fe(IV)TMPyP (438 nm) spectra. These observations lead to the conclusion that H2O2 was produced first by electrochemical reduction of O2, which then converted Fe(III)TMPyP into O=Fe(IV)TMPyP to activate luminol. The current efficiencies for the formation of H2O2 were estimated as about 30-65% in all over the pH.     

Electrochemical generation of free nitric oxide from nitrite catalyzed by iron meso-tetrakis(4-N-methylpyridiniumyl)porphyrin

Electrochemical generation of free nitric oxide (NO) from nitrite (NO(2)(-)) catalyzed by iron meso-tetrakis(4-N-methylpyridiniumyl)porphyrin, [Fe(III)(TMPyP)](5+), has been developed in this study. To obtain free NO, a cathodic electrolysis and an anodic electrolysis were performed in two connected flow electrolytic cells in sequence. The flow electrolytic cell upstream was used for cathodic electrolysis, where the solution of [Fe(III)(TMPyP)](5+) and NO(2)(-) was reduced at -0.25 V (vs Ag/AgCl) into [Fe(II)(NO(2)(-))(2)(TMPyP)](2+) and [Fe(II)(NO)(TMPyP)](4+) in sequence. The flow electrolytic cell downstream was utilized for anodic electrolysis, where [Fe(II)(NO)(TMPyP)](4+) formed from the upstream cell was oxidized at +0.40 V (vs Ag/AgCl) into [Fe(III)(TMPyP)](5+) and free NO. Finally, NO was bubbled out from anodic electrolyte by argon gas. The mechanism and the optimum conditions for electrochemical generation of NO from NO(2)(-) catalyzed by [Fe(III)(TMPyP)](5+) were studied in detail by voltammetric and spectroelectrochemical methods.     

pH transients during salt removal in isoelectric trapping separations: a curse revisited

The pH transients that occur during isoelectric trapping separations as a result of the removal of nonampholytic ionic components have been re-examined. Salts containing strong electrolyte anions and cations, both with equal and dissimilar mobilities, have been studied using anodic and cathodic buffering membranes whose pH values were both equidistant and nonequidistant from pH 7. The direction and magnitude of the pH transient (acidic or basic) was found to depend on both the mobilities of the anion and cation (mu(anion)/mu(cation)) and the pH difference between pH 7 and the pH of the buffering membranes (|pH(memb) (anodic) - 7|/|7 - pH(memb) (cathodic)|). When |pH(memb) (anodic) - 7|/|7 - pH(memb) (cathodic)| = 1, mu(anion)/mu(cation)<1 leads to an acidic pH transient, mu(anion)/mu(cation) = 1 eliminates the pH transient and mu(anion)/mu(cation)>1 leads to a basic pH transient. When mu(anion)/mu(cation) = 1, |pH(memb) (anodic) - 7|/|7 - pH(memb) (cathodic)|<1 leads to a basic pH transient, |pH(memb) (anodic) - 7|/|7 - pH(memb) (cathodic)| = 1 eliminates the pH transient and |pH(memb) (anodic) - 7|/|7 - pH(memb) (cathodic)|>1 leads to an acidic pH transient. By selecting appropriate anodic and cathodic buffering membranes to adjust the |pH(memb) (anodic) - 7|/|7 - pH(memb) (cathodic)| value, pH transients caused by dissimilar anion and cation mobilities can be avoided.     

聚邻甲苯胺的合成及物理化学性质

聚苯胺的导电性和电化学特性已被广泛地研究。最近,对苯胺衍生物的聚合物也开始了研究,如聚邻甲氧基苯胺、聚邻苯二胺和聚邻氨基酚,其中聚邻甲氧基苯胺是一种可溶性的导电高分子材料。为了探讨苯胺聚合的机理和苯胺上不同基团对聚苯胺性质的影响,我们使用了十六种苯     

Voltammetric Determination of Hemoglobin Using a Pencil Lead Electrode

In this paper the electrochemical behavior of hemoglobin (Hb) immobilized on a pencil lead electrode (PLE) was investigated. Immobilization of Hb on the pencil lead electrode was performed by nonelectrochemical and electrochemical methods. In phosphate buffer solution with pH 7.0 Hb showed a pair of well‐defined and nearly reversible redox waves (the anodic and cathodic peak potentials are located at ?0.18 V and ?0.22 V, respectively). The dependence of the anodic peak potential (E_pa) on the pH of the buffer solution indicated that the conversion of Hb? Fe(III)/Hb? Fe(II) is a one‐electron‐transfer reaction process coupled with one‐proton‐transfer. In addition the effect of scan rate on peak currents and peak separation potential was investigated and electrochemical parameters such as α and k_s were calculated. In the second part of this work, the ability of the electrode for determination of Hb concentration was investigated. The results showed a linear dynamic range from 0.15 to 2 µM and a detection limit of 0.11 µM. The relative standard deviation is 4.1 % for 4 successive determinations of a 1 µM Hb solution.     

Electrochemical and spectral studies on the reductive nitrosylation of water-soluble iron porphyrin

The reaction of iron(III) (meso-tetrakis(N-methylpyridinium-4-yl)porphyrin (Fe(III)TMPyP) with nitric oxide (NO) was studied by electronic absorption spectroscopy, ESR, and electrochemical and spectroelectrochemical techniques in aqueous solutions with pH from 2.2 to 12.0. Fe(III)TMPyP has been found to undergo a reductive nitrosylation in all pHs, and the product of nitric oxide binding to the porphyrin has been determined as iron(II) porphyrin nitrosyl complex ([Fe(II)(NO)TMPyP]). The rate of the reductive nitrosylation exhibits a tendency to get faster with increase in pH. An intermediate species was observed around neutral pH by spectroelectrochemical technique and was proposed to be the iron(II) nitrosyl complex of the mu-oxo dimeric form of FeTMPyP, which is known to be a predominant in neutral solutions.     

Sulfite induced autoxidation of NiII and CoII tetraglycine complexes. Spectrophotometric and rotating ring-disc voltammetric studies

The oxidation of Ni(II) and Co(II) tetraglycine complexes in borate buffer aqueous solution, by dissolved oxygen, is strongly accelerated by sulfite. The formation of Ni(III) and Co(III) complexes with maximum absorbances at 327 and 265 nm, respectively, was followed by spectrophotometric measurements. Ni(III) formation was also characterized by voltammetry at low temperatures, whose anodic and cathodic components were observed in the recorded voltammograms. Spectra and rotating ring-disc voltammograms, recorded at various rotation speed values, showed that the Ni(III) species decomposes. The electrochemical process related to the couple Co(II)/Co(III), in a medium containing tetraglycine, was not reversible. In both Ni(II) and Co(II) complexes the metal ion oxidation in the presence of oxygen and sulfite involves the reduction of some initial Ni(III) or Co(III) by sulfite to produce the SO(3).- radical, which rapidly reacts with dissolved oxygen to produce SO(5).-, which then oxidizes Ni(II) or Co(II).     

苯胺在碱性溶液中的电化学聚合和聚合物的性质

苯胺在碱性溶液中电化学氧化时，阳极上形成深黄色的聚苯胺，其氧化峰电位为０．７Ｖ（ｖｓ．Ａｇ／ＡｇＣｌ含饱和ＫＣｌ溶液），比在酸性溶液中氧化约低０．３Ｖ，环一盘电极实验结果表明，在碱性溶液中，苯胺氧化时生成两种可溶性的中间物，形成的聚合物颜色不随电位和ｐＨ值而变化，在空气和碱性溶液中具有很高的稳定性，在紫外－可见光谱图上，聚合物的吸收峰出现在５００ｍ左右。     

Modulation of metal displacements in a saddle distorted macrocycle: synthesis, structure, and properties of high-spin Fe(III) porphyrins and implications for the hemoproteins

A rare family of five and six-coordinated high-spin Fe(III) porphyrins incorporating weak axial ligands are synthesized and structurally characterized which demonstrate, for the first time, stepwise metal displacements in a single distorted macrocyclic environment that has generally been seen in many biological systems. The introduction of four nitro groups into the meso-positions of octaethyl porphyrin severely distorts the porphyrin geometry and provides an interesting modulation of the macrocycle properties which enables the facile isolation of "pure" high-spin Fe(III)(tn-OEP)Cl, Fe(III)(tn-OEP)(MeOH)Cl, and Fe(III)(tn-OEP)(H2O)2(+) in excellent yields in a saddle distorted macrocyclic environment that are known to stabilize intermediate spin states. The stepwise out-of-plane displacements of iron are as follows: 0.47 A for Fe(III)(tn-OEP)Cl; 0.09 A for Fe(III)(tn-OEP)(MeOH)Cl, and 0.01 A for Fe(III)(tn-OEP)(H2O)2(+) from the mean plane of the porphyrins. However, in both five and six-coordinated Fe(III) porphyrins, the Fe-Np distances are quite comparable while the porphyrin cores have expanded significantly, virtually to the same extent for the six-coordinate complexes reported here. The large size of the high-spin iron(III) atom in Fe(III)(tn-OEP)(H2O)2(+) is accommodated perfectly with no displacement of the metal. This expansion is accompanied by a significant decrease of the saddle distortion with a clear increase of the ruffling. Furthermore, the Fe atom in Fe(III)(tn-OEP)(MeOH)Cl is not out of plane because of the larger atom size; however, the displacement of the iron depends on both the relative strength of the axial ligands, as well as the nature and extent of the ring deformation. Our characterization demonstrates that increase in ruffling and/or decrease in macrocycle deformation brings the iron atom more into the plane in a distorted macrocyclic environment. Our observations thus suggest that the displacements of iron in proteins are the consequences of nonequivalent axial coordination, as well as protein induced deformations at the heme. The high-spin nature of the complexes reported here is believed to be due to the larger Fe-Np distances which then reduce substantially the interaction between iron d(x2)-y2 and porphyrin a(2u) orbital. The Fe(III)/Fe(II) reduction potential of Fe(III)(tn-OEP)Cl shows a reversible peak at large positive value (0.20 V), and no ring-centered oxidation was observed within the solvent limit (approximately 1.80 V). It is thus easier to reduce Fe(III)(tn-OEP)Cl by almost 700 mV compared to Fe(III)(OEP)Cl while oxidations are very difficult. Furthermore, the addition of 3-Cl-pyridine to Fe(III)(tn-OEP)Cl in air undergoes spontaneous auto reduction to produce the rare air-stable Fe(II)(tn-OEP)(3-Cl-py)2 that shows Fe(II)/Fe(III) oxidation peaks at high positive potential (0.79 V), which is approximately 600 mV more anodic compared to [Fe(II)(tn-OEP)Cl](-). This large anodic shift illustrates the effective removal of metal-centered electron density by the macrocycle when the metal is constrained to reside in the porphyrin plane.     

甲醛在脯氨酸膜修饰电极上的电催化氧化

应用电化学法和光谱电化学法研究了脯氨酸膜修饰电极的制备 ,用循环伏安法探讨了该膜的电化学性质及其对甲醛的催化氧化 .该电极催化稳定性良好 ,在NaOH溶液中 ,掺杂Ni (Ⅱ )后的脯氨酸膜修饰电极对甲醛和乙醇的氧化均有一定的催化活性 ,但对甲醛的催化活性更佳     

Electrodeposition and stripping voltammetry of arsenic(III) and arsenic(V) on a carbon black–polyethylene composite electrode in the presence of iron ions

In this work, a new sensor is proposed for the stripping voltammetric determination (anodic stripping voltammetry—ASV) of total arsenic(V) or arsenic(III). The sensor is based on an Fe-modified carbon composite electrode containing 30 % carbon black–high-pressure polyethylene (CB/PE). The modification with iron is achieved by the addition of Fe(III) or Fe(II) ions to the sample solution and co-electrodeposition of iron and arsenic on the CB/PE electrode. In anodic stripping voltammetry, two peaks are observed: an Fe peak at ?0.45 or ?0.29 V and a peak at 0.12?±?0.07 V which depends on the arsenic concentration and corresponds to the As(0) → As(III) oxidation, as is the case with other solid electrodes. The optimum conditions proposed for ASV determination of As(V) and As(III) in solutions in the presence of dissolved oxygen are the following: the background electrolyte is 0.005 M HCl containing 0.5–1 mg/?L Fe(III) for As(V) and containing 1.0–1.5 mg/?L Fe(III) for As(III), respectively; E _dep?=??2.3 V; rest period at ?0.10 V for 3–5 s before the potential sweep from ?0.2 to +0.4 V; scan rate is 120 mV/?s. The detection limit (LOD, t?=?120 s) for As(III) and As(V) is 0.16 and 0.8 μg/?L, respectively. Various hypotheses on the effect of Fe ions and atoms on the electrodeposition and dissolution of arsenic are considered. The new method of determination of As(III) and As(V) differs from known analogues by its simplicity, low cost, and easy accessibility of the electrode material. It allows the voltammetric determination of total arsenic after chemical reduction of all its forms to As(III) or after their oxidation to As(V).     

铅电极在硫酸溶液中的光电化学行为

研究了铅电极在阳极氧化过程中光响应的产生机制。结果表明，Ｐｂ电极在光照氧化时存光活化过程，且光经过程须在电位高于０Ｖ时才能发生。采用现场测量光电压技术研究了Ｐｂ电极在硫酸溶液中的恒电流极化过程。     

纳米尺度TiO2微粒多孔膜电极光电化学

用光电流作用谱、光电流-电势图和瞬态光电流谱等光电化学方法研究了TiO2多孔膜电极在含不同氧化还原体系的电解质溶液中的光电转换过程.结果说明TiO2多孔股为n-型半导体，其禁带宽度为3.26eV.当在电解质溶液中加入醌二苯酸（BQ／HQ），TiO2多孔膜电极的光电流作用谱形基本与没加氧化还原对时类似。在可见光区的光电流拖尾是由于醌被光激发，然后给出电子到TiO2多孔膜导带而产生阳极光电流.而在电解质溶液中加入Fe（CN）3-6-／4-时，TiO2多孔膜电极的光电流作用谱有明显的改变.除了在小于380nm短波区有光电流峰外，还在400-600nm的可见光区观察到宽的光电流峰，大大增加了光电流转换效率.同时在小于-0.2V下为阳极光电流，在-0.2V～0.3V电势区间为明显阴极光电流，在大于0.3V下可观察到较弱的阳极光电流.当电极电势大于-0.2V时，光电流瞬态谱在开始光照时有一阴极瞬态光电流尖峰，然后转变为阳极稳态光电流.这是因为当电极电势较负时，Fe（CN）4-6与TiO2的电子传递络合物可以吸收光子，光生电子迅速注入TiO2导带，然后还原溶液中的而产生阴极光电流.     

Arsenate uptake and arsenite simultaneous sorption and oxidation by Fe-Mn binary oxides: influence of Mn/Fe ratio, pH, Ca2+, and humic acid

Arsenate retention, arsenite sorption and oxidation on the surfaces of Fe-Mn binary oxides may play an important role in the mobilization and transformation of arsenic, due to the common occurrence of these oxides in the environment. However, no sufficient information on the sorption behaviors of arsenic on Fe-Mn binary oxides is available. This study investigated the influences of Mn/Fe molar ratio, solution pH, coexisting calcium ions, and humic acids have on arsenic sorption by Fe-Mn binary oxides. To create Fe-Mn binary oxides, simultaneous oxidation and co-precipitation methods were employed. The Fe-Mn binary oxides exhibited a porous crystalline structure similar to 2-line ferrihydrite at Mn/Fe ratios 1:3 and below, whereas exhibited similar structures to δ-MnO(2) at higher ratios. The As(V) sorption maximum was observed at a Mn/Fe ratio of 1:6, but As(III) uptake maximum was at Mn/Fe ratio 1:3. However, As(III) adsorption capacity was much higher than that of As(V) at each Mn/Fe ratio. As(V) sorption was found to decrease with increasing pH, while As(III) sorption edge was different, depending on the content of MnO(2) in the binary oxides. The presence of Ca(2+) enhanced the As(V) uptake under alkaline pH, but did not significantly influence the As(III) sorption by 1:9 Fe-Mn binary oxide; whereas the presence of humic acid slightly reduced both As(V) and As(III) uptake. These results indicate that As(III) is more easily immobilized than As(V) in the environment, where Fe-Mn binary oxides are available as sorbents and they represent attractive adsorbents for both As(V) and As(III) removal from water and groundwater.     

Voltammetric determination of arsenic in high iron and manganese groundwaters

Determination of the speciation of arsenic in groundwaters, using cathodic stripping voltammetry (CSV), is severely hampered by high levels of iron and manganese. Experiments showed that the interference is eliminated by addition of EDTA, making it possible to determine the arsenic speciation on-site by CSV. This work presents the CSV method to determine As(III) in high-iron or -manganese groundwaters in the field with only minor sample treatment. The method was field-tested in West-Bengal (India) on a series of groundwater samples. Total arsenic was subsequently determined after acidification to pH 1 by anodic stripping voltammetry (ASV). Comparative measurements by ICP-MS as reference method for total As, and by HPLC for its speciation, were used to corroborate the field data in stored samples. Most of the arsenic (78 ± 0.02%) was found to occur as inorganic As(III) in the freshly collected waters, in accordance with previous studies. The data shows that the modified on-site CSV method for As(III) is a good measure of water contamination with As. The EDTA was also found to be effective in stabilising the arsenic speciation for longterm sample storage at room temperature. Without sample preservation, in water exposed to air and sunlight, the As(III) was found to become oxidised to As(V), and Fe(II) oxidised to Fe(III), removing the As(V) by adsorption on precipitating Fe(III)-hydroxides within a few hours.     

Direct Electrochemistry of Hemoglobin Immobilized in Sodium Alginate Film on the Ionic Liquid [BMIM]PF6 Modified Carbon Paste Electrode

In recent years the direct electron transfer of redox protein on electrode surface has attracted great attentions1. Different kind of modified electrode and various supporting films for immobilization of proteins had been proposed. But most of them are ba…     

The Interaction of Water‐Soluble Manganese Porphyrins with DNA Films and Their Electrocatalytic Properties with Hydrazine

The electrochemistry of water‐soluble manganese porphyrins (Mn(4‐TMPyP)) has been studied as an electrochemically‐active film on double‐stranded deoxyribonucleic acid (dsDNA) modified electrodes in solutions at various pH. An electrochemical quartz crystal microbalance and cyclic voltammetry were used to study the in situ deposition of DNA on gold disk electrodes, and Mn(4‐TMPyP) (manganese meso‐tetrakis‐(N‐methyl‐4‐pyridyl)porphyrin) deposition on DNA film modified electrodes. Mn^II(4‐TMPyP) (the reduced form) is more easily deposited on a DNA film than Mn^III(4‐TMPyP) (the oxidized form). Electrodeposition of Mn(4‐TMPyP) can be performed in strong basic aqueous solutions, and shows two redox couples with electrochemically active voltammograms. The films can also be produced on glassy carbon, platinum, gold, and transparent semiconductor tin (IV) oxide electrodes. The Mn(4‐TMPyP)/DNA film was electrocatalytically oxidative for hydrazine, hydroxylamine, and SO in a basic aqueous solution through a Mn(IV) species. The electrocatalytic efficiency of Mn^IV(O)(4‐TMPyP) was observed to be greater than (OH)Mn^IV(O)(4‐TMPyP). Electrocatalytic oxidation by a Mn(4‐TMPyP) film as a catalyst for hydrazine oxidation is also discussed. This shows a new anodic peak current in the second segment after the positive scan during electrocatalytic oxidation, and is pH dependent.     

Electrochemistry and electrocatalysis of hemoglobin in Nafion/nano-CaCO3 film on a new ionic liquid BPPF6 modified carbon paste electrode

Room temperature ionic liquid N-butylpyridinium hexafluorophosphate (BPPF6) was used as a binder to construct a new carbon ionic liquid electrode (CILE), which exhibited enhanced electrochemical behavior as compared with the traditional carbon paste electrode with paraffin. By using the CILE as the basal electrode, hemoglobin (Hb) was immobilized on the surface of the CILE with nano-CaCO3 and Nafion film step by step. The Hb molecule in the film kept its native structure and showed good electrochemical behavior. In pH 7.0 Britton-Robinson (B-R) buffer solution, a pair of well-defined, quasi-reversible cyclic voltammetric peaks appeared with cathodic and anodic peak potentials located at -0.444 and -0.285 V (vs SCE), respectively, and the formal potential (E degrees') was at -0.365 V, which was the characteristic of Hb Fe(III)/Fe(II) redox couples. The formal potential of Hb shifted linearly to the increase of buffer pH with a slope of -50.6 mV pH-1, indicating that one electron transferred was accompanied with one proton transportation. Ultraviolet-visible (UV-vis) and Fourier transform infrared (FT-IR) spectroscopy studies showed that Hb immobilized in the Nafion/nano-CaCO3 film still remained its native arrangement. The Hb modified electrode showed an excellent electrocatalytic behavior to the reduction of H2O2, trichloroacetic acid (TCA), and NaNO2.     

On the chemical and electrochemical one-electron reduction of peroxynitrous acid

Peroxynitrous acid was reduced by cathodic linear sweep voltammetry at a gold electrode and by iodide at pH 3.2 and 5.6. The cathodic reduction wave was identified by measuring its decay in time, which was the same as observed by optical spectroscopy. The iodide oxidation was followed by optical measurement of the triiodide formation. Both reductions show one-electron stoichiometry, with the product n(alpha)alpha = 0.23 +/- 0.04 from the electrochemical experiments, in which alpha is the transfer coefficient and n(alpha) the number of electrons transferred, and an diiodine yield of ca. 0.5 equiv per equivalent of peroxynitrous acid. The voltammetric reduction was irreversible up to scan rates of 80 V s(-1). Both reductions were pH independent in the range studied. The voltammetric reduction is most likely an irreversible elemental reaction followed by a chemical decay that cannot be observed directly. Because of the pH independence, we conclude that both reductions have a common short-lived intermediate, namely [HOONO]*-. We estimate the electrode potential of the likely ONOOH/ONOOH*- couple to be larger than 1 V. The commonly used electrode potential E degrees (ONOOH, H+/NO2*, H2O) does not describe the chemistry of peroxynitrous acid.     

Peculiarities of anodic behavior of gold electrode in thiosulfate electrolytes

Using the methods of quartz microgravimetry and voltammetry, the anodic behavior of gold electrode in thiosulfate electrolytes is studied in the pH range of 7 to 11. It is found that, in the potential range from 0.15 to 1.0 V (NHE), the anodic current is associated predominantly with the oxidation of thiosulfate ions, and the gold dissolution rate in this electrolyte is negligibly low (< 0.02 mA/cm²). It is shown that the study of anodic processes in the neutral thiosulfate electrolytes requires stabilization of solution acidity, because the near-anode layer can be acidified to the pH values, which are sufficient for the formation of elemental sulfur. It is found that the use of Britten-Robinson buffer solution with pH 7 as the supporting electrolyte changes significantly the polarization curve of thiosulfate ion oxidation, but does not raise the gold dissolution rate. An increase in the solution pH to 11 and an exposure of electrode at various potentials (−0.5 and 0.15 V) prior to the onset of potential scanning also do not accelerate considerably the gold dissolution in the thiosulfate electrolyte. A comparison between the regularities of gold anodic behavior in the thiosulfate solutions and earlier studied gold dissolution in the cyanide and thiocarbamide electrolytes showed that they are similar. It is supposed that the specific features of anodic processes in these cases are of a similar nature: the metal dissolution proceeds with the formation of two-ligand complexes with linear structure, which is typical for all aforementioned ligands.