Substrate effects in poly(ethylene glycol) self-assembled monolayers on granular and flame-annealed gold

Poly(ethylene glycol) (PEG) self-assembled monolayers (SAMs) are surface coatings that efficiently prevent nonspecific adhesion of biomolecules to surfaces. Here, we report on SAM formation of the PEG thiol CH3O(CH2CH2O)17NHCO(CH2)2SH (PEG(17)) on three types of Au films: thermally evaporated granular Au and two types of Au films from hydrogen flame annealing of granular Au, Au(111), and Au silicide. The different Au surfaces clearly affects the morphology and mechanical properties of the PEG(17) SAM, which is shown by AFM topographs and force distance curves. The two types of SAMs found on flame-annealed Au were denoted "soft" and "hard" due to their difference in stiffness and resistance to scratching by the AFM probe. With the aim of nanometer scale patterning of the PEG(17), the SAMs were exposed by low energy (1 kV) electron beam lithography (EBL). Two distinctly different types of behaviour were observed on the different types of SAM; the soft PEG(17) SAM was destroyed in a self-developing process while material deposition was dominant for the hard PEG(17) SAM.     

Mixed self-assembled monolayers of semirigid tetrahydro-4H-thiopyran end-capped oligo(cyclohexylidenes)

Single-component and mixed self-assembled monolayers (SAMs) of one- and three-ring semirigid tetrahydro-4H-thiopyran end-capped oligo(cyclohexylidenes)-that is, thiopyran (1), 4-(4-cyclohexylidene-cyclohexylidene)tetrahydro-4H-thiopyran (2), and 4-(tetrahydro-4H-thiopyran-4-cyclohexylidene-4'-ylidene)tetrahydro-4H-thiopyran (3)--on Au(111) substrates have been prepared and studied by cyclic voltammetry (CV), atomic force microscopy (AFM), and scanning tunneling microscopy (STM). It was found that the shortest adsorbate 1 more readily forms a SAM than 2 or 3. Notwithstanding, the SAMs of 2 or 3 are thermodynamically more stable due to favorable intermolecular attractions. Holes were made with the AFM tip establishing tilt angles of 30-50 degrees with respect to the surface normal for all SAMs. STM imaging showed well-ordered, line-shaped packing patterns with molecular resolution for the SAM of 2. Similar patterned structures were not observed for 1 and 3. Mixed SAMs were prepared by exposing a SAM of 1 to ethanol solutions of either 2 or 3. STM imaging revealed that domains of molecules of 2 or 3 amidst a monolayer of 1 are formed in both cases. Whereas in the mixed SAM of 1 and 2 the domains are irregularly shaped, circular islands of uniform size are found in the mixed SAM of 1 and 3.     

Interfacial energetics of protein adsorption from aqueous buffer to surfaces with varying hydrophilicity

Adsorption isotherms constructed from time-and-concentration-dependent advancing contact angles thetaa show that the profound biochemical diversity among ten different blood proteins with molecular weight spanning 10-1000 kDa has little discernible effect on the amount adsorbed from aqueous phosphate-buffered saline (PBS) solution after 1 h contact with a particular test surface selected from the full range of observable water wettability (as quantified by PBS adhesion tension tauoa=gammaolv cos thetaoa; where gammaolv is the liquid-vapor interfacial tension and thetaoa is the advancing PBS contact angle). The maximum advancing spreading pressure, Pimaxa, determined from adsorption isotherms decreases systematically with tauoa for methyl-terminated self-assembled monolayers (CH3 SAM, tauo=-15 mN/m), polystyrene spun-coated onto electronic-grade SiOx wafers (PS, tauo=7.2 mN/m), aminopropyltriethoxysilane-treated SiOx surfaces (APTES, tauo = 42 mN/m), and fully water wettable SiOx (tauo=72 mN/m). Likewise, the apparent Gibbs' surface excess [Gammasl-Gammasv], which measures the difference in the amount of protein adsorbed Gamma (mol/cm2) at solid-vapor (SV) and solid-liquid (SL) interfaces, decreases with tauo from maximal values measured on the CH3 SAM surface through zero (no protein adsorption in excess of bulk solution concentration) near tauo=30 mN/m (thetaa=65 degrees). These latter results corroborate the conclusion drawn from independent studies that water is too strongly bound to surfaces with tauo>or=30 mN/m to be displaced by adsorbing protein and that, as a consequence, protein does not accumulate within the interfacial region of such surfaces at concentrations exceeding that of bulk solution ([Gammasl-Gammasv]=0 at tauo=30 mN/m). Results are collectively interpreted to mean that water controls protein adsorption to surfaces and that the mechanism of protein adsorption can be understood from this perspective for a diverse set of proteins with very different amino acid compositions.     

Self-assembled monolayers prepared from ω-thiophene-functionalized n-alkyltrichlorosilane on silicon substrates

Self-assembled monolayers (SAMs) of thienyl-functionalized n-alkyltrichlorosilane (11-(3-thienyl)undecyltrichlorosilane [TUTS]) have been prepared by adsorption from solution and characterized by using X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), contact angle measurements, ellipsometry, and scanning electron microscopy (SEM). Using contact angle and SEM measurements, the film preparation protocol was optimized, resulting in reproducible SAM formation with no adverse deposition of polysiloxane particles. XPS and ellipsometry studies confirmed the existence of SAM formation. AFM results show a smooth and homogeneous SAM, with surface roughness of Ra≤0.2 nm, which is slightly higher than the corresponding values for octadecyltrichlorosilane (OTS) SAMs. Such thiophene-based SAM surfaces can be used for surface-initiated polymerization of thiophene. The resulting formed polythiophene layers at non-compatible surfaces offer some practical applications in manufacturing [W. Plieth, A. Fikus, D. Appelhans, H.-J. Adler, German Patent Application No. 2661977 (1998); D. Appelhans, D. Ferse, H.-J. Adler, A. Fikus, W. Plieth, B. Aldolphi et al., J. Electrochem. Soc. (accepted)].     

Strong resistance of a thin crystalline layer of balanced charged groups to protein adsorption

Resistance of mixed self-assembled monolayers (SAMs) with various counter-charged terminal groups of different valence and protonation/deprotonation states to nonspecific protein adsorption is investigated. It is demonstrated that excellent nonfouling surfaces can be readily constructed from mixed positively and negatively charged components of equal valence in a wide range of thiol solution compositions. Furthermore, the lattice structure of one of the mixed SAM systems studied is revealed by atomic force microscopy (AFM) to be (5.2 +/- 0.2 A x 5.2 +/- 0.2 A)60 degrees . Results indicate that the packing structure of mixed charged SAMs is determined by strong charge-charge interactions of the terminal groups rather than S-Au and chain-chain interactions. This work provides direct evidence that conformational flexibility is not required for protein resistance of a surface and even a single compact layer of charged groups of balanced charge with a crystalline structure can resist nonspecific protein adsorption, suggesting that tightly bound water molecules on the topmost part of the mixed SAMs play a dominant role in surface resistance to nonspecific protein adsorption.     

Mechanism underlying bioinertness of self-assembled monolayers of oligo(ethyleneglycol)-terminated alkanethiols on gold: protein adsorption, platelet adhesion, and surface forces

The mechanism underlying the bioinertness of the self-assembled monolayers of oligo(ethylene glycol)-terminated alkanethiol (OEG-SAM) was investigated with protein adsorption experiments, platelet adhesion tests, and surface force measurements with an atomic force microscope (AFM). In this work, we performed systematic analysis with SAMs having various terminal groups (-OEG, -OH, -COOH, -NH(2), and -CH(3)). The results of the protein adsorption experiment by the quartz crystal microbalance (QCM) method suggested that having one EG unit and the neutrality of total charges of the terminal groups are essential for protein-resistance. In particular, QCM with energy dissipation analyses indicated that proteins absorb onto the OEG-SAM via a very weak interaction compared with other SAMs. Contrary to the protein resistance, at least three EG units as well as the charge neutrality of the SAM are found to be required for anti-platelet adhesion. When the identical SAMs were formed on both AFM probe and substrate, our force measurements revealed that only the OEG-SAMs possessing more than two EG units showed strong repulsion in the range of 4 to 6 nm. In addition, we found that the SAMs with other terminal groups did not exhibit such repulsion. The repulsion between OEG-SAMs was always observed independent of solution conditions [NaCl concentration (between 0 and 1 M) and pH (between 3 and 11)] and was not observed in solution mixed with ethanol, which disrupts the three-dimensional network of the water molecules. We therefore concluded that the repulsion originated from structured interfacial water molecules. Considering the correlation between the above results, we propose that the layer of the structured interfacial water with a thickness of 2 to 3 nm (half of the range of the repulsion observed in the surface force measurements) plays an important role in deterring proteins and platelets from adsorption or adhesion.     

Chemistry on surface-confined molecules: an approach to anchor isolated functional units to surfaces.

The synthesis of surface-confined, nanometer-sized dendrimers and Au nanoparticles was performed starting from single Pd(II) pincer adsorbate molecules (10) embedded as isolated species into 11-mercapto-1-undecanol and decanethiol self-assembled monolayers (SAMs) on gold. The coordination of monolayer-protected Au nanoclusters (MPCs) bearing phosphine moieties at the periphery (13), or dendritic wedges (8) having a phosphine group at the focal point, to SAMs containing individual Pd(II) pincer molecules was monitored by tapping mode atomic force microscopy (TM AFM). The individual Pd(II) pincer molecules embedded in the decanethiol SAM were visualized by their coordination to phosphine MPCs 13; isolated objects with a height of 3.5 +/- 0.7 nm were observed by TM AFM. Reaction of these embedded Pd(II) pincer molecules with the dendritic wedge 8 yielded individual molecules with a height of 4.3 +/- 0.2 nm.     

Chemical stability of nonwetting, low adhesion self-assembled monolayer films formed by perfluoroalkylsilanization of copper

A self-assembled monolayer (SAM) has been produced by reaction of 1H,1H,2H,2H-perfluorodecyldimethylchlorosilane (PFMS) with an oxidized copper (Cu) substrate and investigated by x-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), friction force microscopy (FFM), a derivative of AFM, and contact angle measurement. FFM showed a significant reduction in the adhesive force and friction coefficient of PFMS modified Cu (PFMS/Cu) compared to unmodified Cu. The perfluoroalkyl SAM on Cu is found to be extremely hydrophobic, yielding sessile drop static contact angles of more than 130 degrees for pure water and a "surface energy" (which is proportional to the Zisman critical surface tension for a Cu surface with 0 rms roughness) of 14.5 mJm2(nMm). Treatment by exposure to harsh conditions showed that PFMS/Cu SAM can withstand boiling nitric acid (pH=1.8), boiling water, and warm sodium hydroxide (pH=12, 60 degrees C) solutions for at least 30 min. Furthermore, no SAM degradation was observed when PFMS/Cu was exposed to warm nitric acid solution for up to 70 min at 60 degrees C or 50 min at 80 degrees C. Extremely hydrophobic (low surface energy) and stable PFMS/Cu SAMs could be useful as corrosion inhibitors in micro/nanoelectronic devices and/or as promoters for antiwetting, low adhesion surfaces or dropwise condensation on heat exchange surfaces.     

Characterization of self-assembled monolayers of thiols on Au(111)

Self-assembled monolayers (SAMs) of n-butanethiol, n-dodecanethiol and their equimolar mixture on Au(111) were prepared and characterized by ellipsometry, contact angle measurement, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). Results revealed that these SAMs are oriented ultrathin films with the thickness of nanometer scale, and the SAMs were influenced by the molecular chain length, the lattice orientation and cleanliness of the substrates. The surface of the longer chain SAM is hydrophobic. The thicknesses of three SAMs of n-butanethiol, n-dodecanethiol and their mixture revealed by ellipsometry and XPS are about 0.59 - 0.67nm, 1.60- 1.69 nm and 1.23 - 1.32nm, respectively. AFM images further demonstrated that the SAM formed by the mixture has some microdomains with two different thicknesses.     

Molecular tilting and its impact on frictional properties of n-alkane self-assembled monolayers

Hydrophobic, methyl-terminated self-assembled monolayer (SAM) surfaces can be used to reduce friction. Among methyl-terminated SAMs, the frictional properties of alkanethiol SAMs and silane SAMs have been well-studied. In this research, we investigated friction of methyl-terminated n-hexatriacontane (C36) SAM and compared its friction properties with the alkanethiol and silane SAMs. Alkane SAM does not have an anchoring group. The alkane molecules stand on the surface by physical adsorption, which leads to a higher surface mobility of alkane molecules. We found that C36 SAM has a higher coefficient of friction than that of octadecyltrichlorosilane (OTS) silane. When an atomic force microscope (AFM) tip was swiped across the alkane SAM with a loading force, we found that the alkane SAM can withstand the tip loading pressure up to 0.48 GPa. Between 0.48 and 0.49Ga, the AFM tip partially penetrated the SAM. When the tip moved away, the deformed SAM healed and maintained the structural integrity. When the loading pressure was higher than 0.49 GPa, the alkane SAM was shaved into small pieces by the tip. In addition, we found that the molecular tilting of C36 molecules interacted with the tribological properties of the alkane SAM surface. On one hand, a higher loading force can push the rod-like alkane molecules to a higher tilting angle; on the other hand, a higher molecular tilting leads to a lower friction surface.     

Acid-base properties and zeta potentials of self-assembled monolayers obtained via in situ transformations

Siloxane-anchored, self-assembled monolayers (SAMs) on single crystal Si were prepared with a variety of surface functional groups using a single commercially available surfactant (1-bromo-11-(trichlorosilyl)undecane) followed by in situ transformations. Polar (thioacetate and thiol), nonpolar (methyl), acidic (sulfonic and carboxylic), basic (various amines), and ionic (alkylammonium) surface functionalities were prepared. For primary amine and sulfonate surfaces, the degree of surface charge as a function of pH was determined ex situ using X-ray photoelectron spectroscopy (XPS). Sulfonate SAMs exhibited much higher effective pKa (approximately 2) than dilute sulfonic acid (-5 to -6), and amine SAMs exhibited much lower pKa (approximately 3) than dilute organic amines (approximately 10). This is attributed to the stabilization of nonionized groups by adjacent ionized groups in the SAM. Zeta potentials of these SAMs as a function of pH were consistent with the XPS results and indicated that ionizable SAM surfaces can generate surface potentials much higher than those of nonionic SAMs (thioacetate, methyl) and typical oxide surfaces.     

DNA-modified electrodes; part 4: optimization of covalent immobilization of DNA on self-assembled monolayers

The covalent immobilization of DNA onto self-assembled monolayer (SAM) modified gold electrodes (SAM/Au) was studied by X-ray photoelectron spectrometry and electrochemical method so as to optimize its covalent immobilization on SAMs. Three types of SAMs with hydroxyl, amino, and carboxyl terminal groups, respectively, were examined. Results obtained by both X-ray photoelectron spectrometry and cyclic voltammetry show that the largest covalent immobilization amount of dsDNA could be gained on hydroxyl-terminated SAM/Au. The ratio of amount of dsDNA immobilized on hydroxyl-terminated SAMs to that on carboxyl-terminated SAMs and to that on amino-terminated SAMs is (3-3.5): (1-1.5): 1. The dsDNA immobilized covalently on hydroxyl-terminated SAMs accounts for 82.8-87.6% of its total surface amount (including small amount of dsDNA adsorbed). So the hydroxyl-terminated SAM is a good substrate for the covalent immobilization of dsDNA on gold surfaces.     

Microscopic wetting of self-assembled monolayers with different surfaces: a combined molecular dynamics and quantum mechanics study

Molecular dynamics simulations are used to study the micronature of the organization of water molecules on the flat surface of well-ordered self-assembled monolayers (SAMs) of 18-carbon alkanethiolate chains bound to a silicon (111) substrate. Six different headgroups (-CH(3), -C═C, -OCH(3), -CN, -NH(2), -COOH) are used to tune the character of the surface from hydrophobic to hydrophilic, while the level of hydration is consistent on all six SAM surfaces. Quantum mechanics calculations are employed to optimize each alkyl chain of the different SAMs with one water molecule and to investigate changes in the configuration of each headgroup under hydration. We report the changes of the structure of the six SAMs with different surfaces in the presence of water, and the area of the wetted surface of each SAM, depending on the terminal group. Our results suggest that a corrugated and hydrophobic surface will be formed if the headgroups of SAM surface are not able to form H-bonds either with water molecules or between adjacent groups. In contrast, the formation of hydrogen bonds not only among polar heads but also between polar heads and water may enhance the SAM surface hydrophilicity and corrugation. We explicitly discuss the micromechanisms for the hydration of three hydrophilic SAM (CN-, NH(2)- and COOH-terminated) surfaces, which is helpful to superhydrophilic surface design of SAM in biomimetic materials.     

Immobilization of proteins on carboxylic acid functionalized nanopatterns

The immobilization of proteins on nanopatterned surfaces was investigated using in situ atomic force microscopy (AFM) and ex situ infrared reflectance–absorption spectroscopy (IRAS). The AFM-based lithography technique of nanografting provided control of the size, geometry, and spatial placement of nanopatterns within self-assembled monolayers (SAMs). Square nanopatterns of carboxylate-terminated SAMs were inscribed within methyl-terminated octadecanethiolate SAMs and activated using carbodiimide/succinimide coupling chemistry. Staphylococcal protein A was immobilized on the activated nanopatterns before exposure to rabbit immunoglobulin G. In situ AFM was used to monitor changes in the topography and friction of the nanopatterns in solution upon protein immobilization. Complementary studies with ex situ IRAS confirmed the surface chemistry that occurred during the steps of SAM activation and subsequent protein immobilization on unpatterned samples. Since carbodiimide/succinimide coupling chemistry can be used for surface attachment of different biomolecules, this protocol shows promise for development of other aqueous-based studies for nanopatterned protein immobilization.     

Effect of the electrostatic interaction on the redox reaction of positively charged cytochrome C adsorbed on the negatively charged surfaces of acid-terminated alkanethiol monolayers on a Au(111) electrode

The electrochemical properties of cytochrome c (cyt c) adsorbed on mixed self-assembled monolayers (SAMs) of 2-mercaptoethanesulfonate (MES)/2-mercaptoethanol (MEL) are compared with those on single-component SAMs of MES, MEL, and mercaptopropionic acid (MPA), using cyclic voltammetry and potential-modulated UV-vis reflectance spectroscopy. The rate constant of electron transfer (ET), k(et), of cyt c adsorbed on the SAM of MPA decreases from 1450 +/- 210 s(-1) at pH 7 to 890 +/- 100 s(-1) at pH 9. In contrast, the value of k(et) of cyt c on the SAM of MES is pH-independent at 100 +/- 15 s(-1). Those facts suggest that a large negative charge density on the SAM surface slows down the ET between cyt c and the electrode. The surface charge density of the SAM affects also the amount of electroactive cyt c, Gamma(e), which decreases from 10.0 +/- 1.0 to 5.3 +/- 1.1 pmol cm(-2) with increasing pH from 7 to 9 on the SAM of MPA. Similarly, the k(et) of cyt c adsorbed on the mixed SAMs of MES/MEL sharply decreases from 900 +/- 300 s(-1) to 110 s(-1) as the surface mole fraction of MES increases beyond 0.5, suggesting the presence of a negative surface charge threshold beyond which the rate of ET of cyt c is dramatically lowered. The decrease in the k(et) on the SAMs at high negative charge densities probably results from the confinement of adsorbed cyt c by the strong electrostatic force to an orientation that is not optimal for the ET reaction.     

Multifunctional mixed SAMs that promote both cell adhesion and noncovalent DNA immobilization

The ability of DNA strands to influence cellular gene expression directly and to bind with high affinity and specificity to other biological molecules (e.g., proteins and target DNA strands) makes them a potentially attractive component of cell culture substrates. On the basis of the potential importance of immobilized DNA in cell culture and the well-defined characteristics of alkanethiol self-assembled monolayers (SAMs), the current study was designed to create multifunctional SAMs upon which cell adhesion and DNA immobilization can be independently modulated. The approach immobilizes the fibronectin-derived cell adhesion ligand Arg-Gly-Asp-Ser-Pro (RGDSP) using carbodiimide activation chemistry and immobilizes DNA strands on the same surface via cDNA-DNA interactions. The surface density of hexanethiol-terminated DNA strands on alkanethiol monolayers (30.2-69.2 pmol/cm2) was controlled using a backfill method, and specific target DNA binding on cDNA-containing SAMs was regulated by varying the soluble target DNA concentration and buffer characteristics. The fibronectin-derived cell adhesion ligand GGRGDSP was covalently linked to carboxylate groups on DNA-containing SAM substrates, and peptide density was proportional to the amount of carboxylate present during SAM preparation. C166-GFP endothelial cells attached and spread on mixed SAM substrates and cell adhesion and spreading were specifically mediated by the immobilized GGRGDSP peptide. The ability to control the characteristics of noncovalent DNA immobilization and cell adhesion on a cell culture substrate suggests that these mixed SAMs could be a useful platform for studying the interaction between cells and DNA.     

Molecular-level approach to inhibit degradations of alkanethiol self-assembled monolayers in aqueous media

A molecular-level approach is developed to prevent or inhibit the degradation processes of alkanethiol self-assembled monolayers (SAMs). Previous studies revealed two degradation pathways: direct desorption and oxidation-desorption. By use of scanning tunneling microscopy (STM) and atomic force microscopy (AFM), in situ and time-dependent imaging reveals and confirms that degradations of alkanethiol SAMs on gold mainly initiate at defect sites, such as domain boundaries and vacancy islands, and then propagate into the ordered domains. Our approach targets at attaching small molecules with preferred adhesion to the defects. The best candidates are aqueous media containing a small amount of amphiphilic surfactant molecules, such as N,N-dimethylformamide (DMF) or dimethyl sulfoxide (DMSO). High-resolution studies demonstrate that DMSO and DMF molecules attach to SAM surfaces and more favorably at defect sites, forming relatively stable adsorbates. This attachment increases the activation energy sufficiently to inhibit both degradation pathways. The robustness of this approach has been investigated as a function of surfactant concentration, solution temperature, and the stirring condition. Molecular-level mechanisms and energetics for degradation inhibition of SAMs are also discussed in detail.     

Fabrication and characterization of metal-molecule-metal junctions by conducting probe atomic force microscopy

Metal-molecule-metal junctions were fabricated by contacting Au-supported alkyl or benzyl thiol self-assembled monolayers (SAMs) with an Au-coated atomic force microscope (AFM) tip. The tip-SAM microcontact is approximately 15 nm(2), meaning the junction contains approximately 75 molecules. Current-voltage (I-V) characteristics of these junctions were probed as a function of SAM thickness and load applied to the microcontact. The measurements showed: (1) the I-V traces were linear over +/-0.3 V, (2) the junction resistance increased exponentially with alkyl chain length, (3) the junction resistance decreased with increasing load and showed two distinct power law scaling regimes, (4) resistances were a factor of 10 lower for junctions based on benzyl thiol SAMs compared to hexyl thiol SAMs having the same thickness, and (5) the junctions sustained fields up to 2 x 10(7) V/cm before breakdown. I-V characteristics determined for bilayer junctions involving alkane thiol-coated tips in contact with alkane thiol SAMs on Au also showed linear I-Vs over +/-0.3 V and the same exponential dependence on thickness. The I-V behavior and the exponential dependence of resistance on alkyl chain length are consistent with coherent, nonresonant electron tunneling across the SAM. The calculated conductance decay constant (beta) is 1.2 per methylene unit ( approximately 1.1 A(-)(1)) for both monolayer and bilayer junctions, in keeping with previous scanning tunneling microscope and electrochemical measurements of electron transfer through SAMs. These measurements show that conducting probe-AFM is a reliable method for fundamental studies of electron transfer through small numbers of molecules. The ability to vary the load on the microcontact is a unique characteristic of these junctions and opens opportunities for exploring electron transfer as a function of molecular deformation.     

Supported bilayer lipid membrane arrays on photopatterned self-assembled monolayers

This work demonstrates the use of photocleavable cholesterol derivatives to create supported bilayer lipid membrane arrays on silica. The photocleavable cholesteryl tether is attached to the surface by using the reaction of an amine-functionalized self-assembled monolayer (SAM) and the N-hydroxysuccinimide-based reagent 9. The resultant SAM contains an ortho-nitrobenzyl residue that can be cleaved by photolysis by using soft (365 nm) UV light regenerating the original amine surface, and which can be patterned using a mask. The photoreaction yield was approximately 75 % which was significantly higher than previously found for related ortho-nitrobenzyl photochemistry on gold substrates. The SAMs were characterized by means of contact angle measurements, ellipsometry and X-ray photoelectron spectroscopy. Patterned surfaces were characterized with SEM and AFM. After immersing the patterned surface into a solution containing small unilamellar vesicles of egg phosphatidylcholine (PC), supported lipid membranes were formed comprised of lipid bilayer over the amine functionalized "hydrophilic" regions and lipid monolayer over the cholesteryl "hydrophobic" regions. This was confirmed by fluorescence microscopy and AFM. FRAP studies yielded a lateral diffusion coefficient for the probe molecule of 0.14+/-0.05 microm(2) s(-1) in the bilayer regions and approximately 0.01 microm(2) s(-1) in the monolayer regions. This order of magnitude difference in diffusion coefficients effectively serves to isolate the bilayer regions from one another, thus creating a bilayer array.     

Mixed charged zwitterionic self-assembled monolayers as a facile way to stabilize large gold nanoparticles

Here we report a facile way of stabilizing large gold nanoparticles (AuNPs) by mixed charged zwitterionic self-assembled monolayers (SAMs). The citrate-capped AuNPs with diameters ranging from 16 nm to even ～100 nm are well stabilized via a simple place exchange reaction with a 1:1 molar ratio mixture of negatively charged sodium 10-mercaptodecanesulfonic acid (HS-C10-S) and positively charged (10-mercaptodecyl)-trimethyl-ammonium bromide (HS-C10-N4). The 16 nm AuNPs protected by mixed charged zwitterionic SAMs not only show much better stability than the single negatively or positively charged AuNPs, but also exhibit exciting stability as well as those modified by monohydroxy (1-mercaptoundec-11-yl) tetraethylene glycol (HS-C11-EG4). Importantly, 16 nm AuNPs protected by mixed SAMs exhibit good stability in cell culture medium with 10% FBS and strong protein resistance, especially with excellent resistance against plasma adsorption. Moreover, the mixed charged zwitterionic SAMs are also able to well-stabilize larger AuNPs with a diameter of 50 nm, and to help remarkably improve their stability in saline solution compared with HS-C11-EG4 protected ones. When it comes to AuNPs with a diameter of 100 nm, the mixed charged zwitterionic SAM protected nanoparticles retain a smaller hydrodynamic diameter and even better long-term stability than those modified by mercaptopolyethylene glycol (M(w) = 2000, HS-PEG2000). The above results demonstrated that the mixed charged zwitterionic SAMs are able to have a similar effect on stabilizing the large gold nanoparticles just like the single-component zwitterionic SAMs. Concerning its ease of preparation, versatility, and excellent properties, the strategy based on the mixed charged zwitterionic SAM protection might provide a promising method to surface tailoring of nanoparticles for biomedical application.