应力导致InAs/In0.15Ga0.85As量子点结构中 In0.15Ga0.85As阱层的合金分解效应研究

利用固源分子束外延技术,在In0.15Ga0.85As/GaAs量子阱生长了两个InAs/In0.15Ga0.85As量子点(DWELL)样品.通过改变其中一个InAs DWELL样品中的In0.15Ga0.85As阱层的厚度和生长温度,获得了量子点尺寸增大而且尺寸分布更均匀的结果.结合光致发光光谱(PL)和压电调制光谱(PzR)实验结果,发现该样品量子点的光学性质也同时得到了极大的优化.基于有效质量近似的数值计算结果表明:量子点后生长过程中应力导致In0.15Ga0.85As阱层合金分解机理是导致量子点尺寸和光学性质得到优化的主要原因.     

调制掺杂的应变In0.60Ga0.40As/In0.52Al0.48As多量子阱结构的光致发光谱研究

报道了调制掺杂的应变In_0.60Ga_0.40As/In_0.52Al_0.48As多量子阱中室温光致发光光谱.观察到n=1和2电子子带到n=1重空穴子带的强发光峰.在低温下可以观察到n=1电子子带到n=1轻空穴弱发光肩胛.通过对发光强度随激发功率及温度依赖关系以及理论模型的分析研究,认为该调制掺杂量子阱中辐射复合效率降低的主要机制是应变失配位错对载流子的陷阱作用.界面上的失配位错是陷阱的主要来源.并用静态的光致发光理论模型 关键词：     

InAs/GaAs表面量子点的压电调制反射光谱研究

运用压电调制反射光谱(PzR)方法测量了在以GaAs(311)B为衬底的In_0.35Ga_0.65As模板上生长的InAs表面量子点结构的反射谱.在77K温度下，观察到了来自样品各个组成结构(包括表面量子点本身、被覆盖层覆盖的量子点、In_0.35Ga_0.65As模板以及GaAs衬底等)的调制信号.来自表面量子点本身的调制信号是多个清晰的调制峰.用一阶和三阶微分洛伦兹线形对PzR谱中对应结构的实验数据进行了拟合，精确确定了与样品的各个组成结构相对应的调制峰的能量位置.对不同样品PzR谱的差异进行了定性的说明. 关键词： 压电调制光谱 InAs/GaAs 表面量子点 洛伦兹线形拟合     

压电调制反射光谱研究GaAs/Al0.29Ga0.71As单量子阱

报道了压电调制反射测量系统的建立，应用该系统获得了势阱宽度分别为5nm和25nm的两个G aAs/Al_0.29Ga_0.71As单量子阱的压电调制反射谱. 从图谱中可以看 出，在室 温下能够较容易地分辨出和轻、重空穴相关联的子带跃迁. 在阱宽25nm的样品中还观察到了 自旋-轨道跃迁. 利用有效质量理论近似计算，对量子阱样品的图谱结构进行了指认，发现 实验值和计算值能够较好地符合. 关键词： 压电调制反射光谱 单量子阱 分子束外延     

两个子带占据的In0.53Ga0.47As/In0.52Al0.48As量子阱中填充因子的变化规律

研究了低温(15K)和强磁场(0—13T)条件下, InP基In_053Ga_047As/In_052Al_048As量子阱中电子占据两个子带时填充因子随磁场的变化规律.结果表明,在电子自旋分裂能远小于朗道能级展宽的情况下,如果两个子带分裂能是朗道分裂能的整数倍时,即ΔE₂₁=kω_c(其中k为整数),填充因子为偶数;当两个子带分裂能为朗道分裂能的半奇数倍时,即ΔE₂₁=(2k+1)ω_c/2,填充因子出现奇数. 关键词： 053Ga_047As/In_052Al_048As量子阱')" href="#">In_053Ga_047As/In_052Al_048As量子阱 填充因子 磁输运     

缓冲层InxGa1-xAs组分对In0.82Ga0.18As结晶质量和表面形貌的影响

采用低压金属有机化学气相沉积(LP-MOCVD)技术,两步生长法在InP衬底上制备In_0.82Ga_0.18As材料.研究缓冲层In_xGa_1-xAs的In组分对In_0.82Ga_0.18As结晶质量和表面形貌的影响.X射线衍射(XRD)用于表征材料的组分和结晶质量.用扫描电子显微镜(SEM)观察样品的表面形貌.实验结果表明,低温生长的缓冲层In_xGa_1-xAs的In组分影响高温生长的外延层In_0.82Ga_0.18As的结晶质量和表面形貌.测量得到四个样品的外延层In_0.82Ga_0.18As的X射线衍射谱峰半峰全宽(FWHM)为0.596°,0.68°,0.362°和0.391°,分别对应缓冲层In组分x=0.28,0.53,0.82,0.88,当缓冲层In组分是0.82时,FWHM最窄,表明样品的结晶质量最好.SEM观察四个样品的表面形貌,当缓冲层In组分是0.82时,样品的表面平整,没有出现交叉平行线或蚀坑等缺陷,表面形貌最佳.     

In0.15Ga0.85As—GaAs应力层多量子阱中束缚子带—连续带跃迁

在10—300K温度范围,研究了稳态发光二极管(LED)辐照对15周期的In_0.15Ga_0.85As(8nm)-CaAs(15nm)应力层多量子阱的光电流谱的影响。各跃迁过程对应的光电流峰的强度随LED光强的增大而减弱,并且具有不同的变化规律。据此可区分出束缚子带和连续带间的跃迁及其亚结构,并由跃迁的能量位置,直接确定导带和价带的不连续量,得出重空穴价带的能带台阶Q_v=0.38±0.01。 关键词：     

In0.53Ga0.47As/InP量子阱与体材料的1 MeV电子束辐照光致发光谱研究

为获得对In_0.53Ga_0.47As/InP材料在电子束辐照下的光致发光谱变化规律, 开展了1 MeV电子束辐照试验, 注量为 5×10¹²-9×10¹⁴ cm^-2. 样品选取量子阱材料和体材料, 在辐照前后, 进行了光致发光谱测试, 得到了不同结构In_0.53Ga_0.47As/InP材料在1 MeV电子束辐照下的不同变化规律; 对比分析了参数退化的物理机理. 结果显示: 试验样品的光致发光峰强度随着辐照剂量增大而显著退化. 体材料最先出现快速退化, 而五层量子阱在注量达到6×10¹⁴ cm^-2时, 就已经退化至辐照前的9%. 经分析认为原因有: 1)电子束进入样品后, 与材料晶格发生能量传递, 破坏晶格完整性, 致使产生的激子数量减少, 光致发光强度降低; 电子束辐照在材料中引入缺陷, 增加了非辐射复合中心密度, 导致载流子迁移率降低. 2)量子阱的二维限制作用使载流子运动受限, 从而能够降低载流子与非辐射复合中心的复合概率; 敏感区域截面积相同条件下, 体材料比量子阱材料辐射损伤更为严重. 3)量子阱的层数越多, 则异质结界面数越多, 相应的产生的界面缺陷数量也随之增多, 辐射损伤越严重.     

内嵌InAs量子点的δ掺杂GaAs/AlxGa1-xAs二维电子气特性分析

采用分子束外延技术对δ掺杂GaAs/Al_xGa_1-xAs二维电子气(2DEG)样品进行了生长. 在样品生长过程中, 分别改变掺杂浓度(N_d)、空间隔离层厚度(W_d) 和Al_xGa_1-xAs中Al组分(x_Al)的大小, 并在双温(300 K, 78 K)条件下对生长的样品进行了霍尔测量; 结合测试结果, 分别对N_d, W_d及x_Al与GaAs/Al_xGa_1-xAs 2DEG的载流子浓度和迁移率之间的关系规律进行了细致的分析讨论. 生长了包含有低密度InAs量子点层的δ掺杂GaAs/Al_xGa_1-xAs 2DEG 样品, 采用梯度生长法得到了不同密度的InAs量子点. 霍尔测量结果表明, 随着InAs量子点密度的增加, GaAs/Al_xGa_1-xAs 2DEG的迁移率大幅度减小, 实验中获得了密度最低为16×10⁸/cm²的InAs量子点样品. 实验结果为内嵌InAs量子点的δ掺杂GaAs/Al_xGa_1-xAs 2DEG的研究和应用提供了依据和参考. 关键词： 二维电子气 InAs量子点 载流子浓度 迁移率     

赝配GaAs/In0.2Ga0.8As量子阱导带不连续量的C-V和电容瞬态测量

分别采用二种不同方法测量分子束外延(MBE)生长GaAs/In_0.2Ga_0.8As单量子阱结构的导带不连续量ΔE_c:1) 考虑样品界面电荷修正的电容-电压(C-V)分布；2) 量子阱载流子热发射产生的电容瞬态(DLTS).C-V测得的ΔE_c=0.227eV,大约相当于89% ΔE_g.DLTS测得的ΔE_c=0.229eV,大约相当于89.9% ΔE_g.结果 关键词：     

Band offsets in In0.15Ga0.85As/ GaAs and In0.15Ga0.85As/Al0.15Ga0.85As studied by photoluminescence and cathodoluminescence

Photoluminescence and cathodoluminescence measurements of strained undoped In_0.15Ga_0.85As/GaAs and In_0.15Ga_0.85As/Al_0.15Ga_0.85As quantum well structures with emission lines attributed to the first electron–first heavy hole and first electron–first light hole excitonic transitions have been analysed theoretically within the eight-band effective mass approximation. For In_0.15Ga_0.85As/GaAs the results are consistent with either type I or type II alignment of the light hole band. In the case of In_0.15Ga_0.85As/Al_0.15Ga_0.85As our results indicate type II alignment for the light hole band and offset ratio ofQ = 0.83.     

Optical transitions of InAs/In0.36Ga0.64As/GaAs(311B) surface quantum dots clearly identified by the piezoreflectance technique

The bilayer InAs/In_0.36Ga_0.64As/GaAs(311B) quantum dots (QDs), including one InAs buried quantum dot (BQD) layer and the other InAs surface quantum dot (SQD) layer, have been grown by molecular beam epitaxy (MBE). The optical properties of these three samples have been studied by the piezoreflectance (PzR) spectroscopy. The PzR spectra do not exhibit only the optical transitions originated from the InAs BQDs, but the features originated from the InAs SQDs. After the InAs SQDs have been removed chemically, those optical transitions from InAs SQDs have been demonstrated clearly by investigating the PzR spectra of the residual InAs BQDs in these samples. The great redshift of these interband transitions of InAs SQDs has been well discussed. Due to the suitable InAs SQD sizes and the thickness of In_0.36Ga_0.64As layer, the interband transition of InAs SQDs has been shifted to ∼1.55 μm at 77 K.     

Annealing effect on the optical properties in Si delta-doped Al0.24Ga0.76As/In0.15Ga0.85As/GaAs pseudomorphic high electron mobility transistor structures

The optical properties of Si delta-doped Al_0.24Ga_0.76As/In_0.15Ga_0.85As/GaAs pseudomorphic high electron mobility transistor structure (PHEMTs) are estimated after the process of rapid thermal annealing (RTA) in the temperature range 500–750°C. After layer intermixing and decrease of 2DEG densities of PHEMTs just occurs around the annealing temperature of 650°C, the 12H transition peak at 1.354 eV above the annealing temperature of 650°C is newly observed from the photoluminescence (PL) and photoreflectance (PR) spectra. From the results of PL and PR measurements in the annealed PHEMTs, it is found that remarkable modification of band profile in InGaAs QW occur at annealing temperature above 650°C.     

Electromodulation spectroscopy of In0.53Ga0.47As/In0.53Ga0.23Al0.24As quantum wells

In_0.53Ga_0.47As/In_0.53Ga_0.23Al_0.24As quantum wells (QWs) of various widths have been grown by molecular beam epitaxy on the InP substrate and investigated by electromodulation spectroscopy, i.e. photoreflectance (PR) and contactless electroreflectance (CER). The optical transitions related to the QW barrier and the QW ground and excited states have been clearly observed in PR and CER spectra. The experimental QW transition energies have been compared with theoretical predictions based on an effective mass formalism model. A good agreement between experimental data and theoretical calculations has been observed when the conduction band offset for the In_0.53Ga_0.47As/In_0.53Ga_0.23Al_0.24As interface equals 60%. In addition, it has been concluded that the conduction band offset for the In_0.53Ga_0.23Al_0.24As/InP interface is close to zero. The obtained results show that InGa(Al)As alloys are very promising materials in the band gap engineering for structures grown on InP substrate.     

Electron g-factor in a gated InAs-inserted-channel In0.53Ga0.47As/In0.52Al0.48As heterostructure

We report on electron g-factor in an InAs-inserted In_0.53Ga_0.47As/In_0.52Al_0.48As heterostructure. The gate voltage dependence of g-factor is obtained from the coincidence method. The obtained g-factor values are surprisingly smaller than the g-factor value of bulk InAs, and it is close to the bare g-factor value of In_0.53Ga_0.47As. The large change in g-factor is observed by applying the gate voltage. The obtained gate voltage dependence is not simply explained by the energy dependence of g-factor.     

0.6-eV bandgap In0.69Ga0.31As thermophotovoltaic devices with compositionally undulating step-graded InAsyP1-y buffers

Single-junction,lattice-mismatched In0.69Ga0.31As thermophotovoltaic(TPV) devices each with a bandgap of 0.6 eV are grown on InP substrate by metal-organic chemical vapour deposition(MOCVD).Compositionally undulating stepgraded InAsyP1-y buffer layers with a lattice mismatch of ～1.2% are used to mitigate the effect of lattice mismatch between the device layers and the InP substrate.With an optimized buffer thickness,the In0.69Ga0.31As active layers grown on the buffer display a high crystal quality with no measurable tetragonal distortion.High-performance single-junction devices are demonstrated,with an open-circuit voltage of 0.215 V and a photovoltaic conversion efficiency of 6.9% at a short-circuit current density of 47.6 mA/cm2,which are measured under the standard solar simulator of air mass 1.5-global(AM 1.5 G).     

Influence of thermal annealing duration of buffer layer on the crystalline quality of In0.82Ga0.18As grown on InP substrate by LP-MOCVD

In_0.82Ga_0.18As epilayers were grown on InP substrates using a two-step growth technique by LP-MOCVD. A homogeneous low-temperature (450 °C) In_0.82Ga_0.18As buffer layer was introduced to improve the crystalline quality of epilayers. The influence of low-temperature buffer layer deposition condition, such as thermal annealing duration, on the crystalline quality of the In_0.82Ga_0.18As epilayer was investigated. Double-crystal X-ray diffraction measurement, Hall measurement, and Raman scattering spectrum were used to evaluate the In_0.82Ga_0.18As epilayers. Atomic force microscope was used to study the surface morphology. It is found that the In_0.82Ga_0.18As epilayer, with buffer layer thermal annealing for 5 min, exhibits the best crystalline quality. The change of the surface morphology of the buffer layer after thermal annealing treatment was suggested to explain the phenomenon.     

Structural and optical properties of In0.5Ga0.5As/GaAs quantum dots in an In0.1Ga0.9As well using repeated depositions of InAs/GaAs short-period superlattices for the application of optical communication

We report structural and optical properties of In_0.5Ga_0.5As/GaAs quantum dots (QDs) in a 100 Å-thick In_0.1Ga_0.9As well grown by repeated depositions of InAs/GaAs short-period superlattices with atomic force microscope, transmission electron microscope (TEM) and photoluminescence (PL) measurement. The QDs in an InGaAs well grown at 510 °C were studied as a function of n repeated deposition of 1 monolayer thick InAs and 1 monolayer thick GaAs for n=5–10. The heights, widths and densities of dots are in the range of 6–22.0 nm, 40–85 nm, and 1.6–1.1×10¹⁰/cm², respectively, as n changes from 5 to 10 with strong alignment along [1 −1 0] direction. Flat and pan-cake-like shape of the QDs in a well is found in TEM images. The bottoms of the QDs are located lower than the center of the InGaAs well. This reveals that there was intermixing—interdiffusion—of group III materials between the InGaAs QD and the InGaAs well during growth. All reported dots show strong 300 K-PL spectrum, and 1.276 μm (FWHM: 32.3 meV) of 300 K-PL peak was obtained in case of 7 periods of the QDs in a well, which is useful for the application to optical communications.