Widely tunable,narrow linewidth Tm: YAG ceramic laser with a volume Bragg grating

We report on a widely tunable, narrow linewidth operation of a Tm:YAG ceramic laser. A volume Bragg grating is used in the cavity as a folding mirror for wavelength selection. The wavelength is tuned from 1956.2 to1995 nm, leading to a total tuning range of 38.7 nm. The linewidth is around 0.1 nm over the whole tuning range. A maximum output power of 1.51 W at 1990.5 nm is achieved at 37.8 W absorbed pump power.Different saturation behaviors are observed in the laser performances at different wavelengths.     

Double-clad Tm3+-doped silica fiber laser with Bragg grating inscribed directly into active core by femtosecond laser

We report for the first time to inscribe the Fiber Bragg Grating (FBG) in Tm³⁺-doped multimode double-clad silica fiber by 800 nm femtosecond laser with a phase mask. The 1.35 μm period Bragg grating is written into the fiber core, which is responded to the laser center wavelength located at nearly 1960 nm. Continuous wave total output power of 11.5 W is obtained under the launched pump power of 29.8 W, corresponding to a slope efficiency of 45.0% and a conversion efficiency of 38.6%.     

Multiwavelength Brillouin-erbium fiber laser incorporating a fiber Bragg grating filter

In this paper, we demonstrate a multiwavelength Brillouin erbium fiber laser in a Fabry-Perot cavity. The design utilized a bidirectional oscillation provided by a fiber Bragg grating filter and a fiber loop mirror at each end of the laser cavity. A stable operation of 25 Brillouin-Stokes lines was obtained at around a 1559-nm band.     

基于飞秒激光直写光纤光栅的掺镱光纤激光器

 利用飞秒激光微加工技术,可以在光纤纤芯内直写出布拉格光栅,它与传统的光纤光栅制作方法相比,具有耗时短、无需光敏光纤、周期可任意设定、光栅稳定性高等优点。采用800 nm钛宝石飞秒激光器,在Hi1060光纤内写入一支8 mm长的布拉格光栅,光纤光栅的周期为2.9 μm,这是中心波长为1 042 nm的八阶光纤布拉格光栅。将所得光栅与一段有源的双包层光纤熔接,作为激光输出镜,利用975 nm的LD光纤模块作为泵浦源,采用端泵浦技术构成双包层光纤激光器。双包层光纤采用Nufern公司镱(Yb³⁺)离子掺杂双包层光纤,光纤长度3 m。所得激光器的输出功率为71.1 W,中心波长1 042 nm,带宽约为0.8 nm。     

基于飞秒激光直写光纤光栅的掺镱光纤激光器

利用飞秒激光微加工技术,可以在光纤纤芯内直写出布拉格光栅,它与传统的光纤光栅制作方法相比,具有耗时短、无需光敏光纤、周期可任意设定、光栅稳定性高等优点。采用800 nm钛宝石飞秒激光器,在Hi1060光纤内写入一支8 mm长的布拉格光栅,光纤光栅的周期为2.9 μm,这是中心波长为1 042 nm的八阶光纤布拉格光栅。将所得光栅与一段有源的双包层光纤熔接,作为激光输出镜,利用975 nm的LD光纤模块作为泵浦源,采用端泵浦技术构成双包层光纤激光器。双包层光纤采用Nufern公司镱(Yb3+)离子掺杂双包层光纤,光纤长度3 m。所得激光器的输出功率为71.1 W,中心波长1 042 nm,带宽约为0.8 nm。     

Regenerated fiber Bragg grating for fiber laser sensing at high temperatures

Thermally regenerated low-reflectivity fiber Bragg gratings(RFBGs), as one mirror of a resonant cavity, have been introduced as linear-cavity fiber lasers combining with fiber saturable absorbers. The output of lasing presents an optical signal-to-noise ratio of 50 dB and temperature sensitivity coefficient of 15.36 pm∕℃ for the heating process and 15.46 pm∕℃ for the cooling process. The lasing wavelength variation and power fluctuation at 700℃ are less than 0.02 nm and 0.21 dB, respectively. The RFBG-based fiber laser sensing has displayed good linearity for both the temperature rising and cooling processes, and favorable stability at high temperatures.     

Fiber Bragg grating strain sensor based on fiber laser

A study on fiber Bragg grating (FBG) strain sensor, based on erbium-doped fiber (EDF) laser, is presented. A strain-sensing element, FBG, also acts as the lasing wavelength selecting component. When strain is applied on the FBG, the laser cavity loss changes, leading to a modification of the laser transient. Strain measurements are obtained in the time domain by simply measuring the EDF laser build-up time. Relative variation in the build-up time of up to 190%, for a strain range from 0 με to 2350 με, is achieved with a resolution corresponding to a strain of better than 2.35 με. This study demonstrates a novel fiber sensor concept and the technical feasibility to develop fiber strain measurement.     

Studies on multi-wavelength fiber Bragg grating laser strain sensor

A novel stable multi-wavelength fiber Bragg grating laser is achieved and its sensing characteristic with the strain is studied. The beat signals generated by the multi-wavelength fiber laser are measured under different strains. Four-wave mixing (FWM) is firstly observed in such a short-cavity fiber laser.     

A self-seeded fiber laser incorporated with a fiber Bragg grating external cavity semiconductor laser

A self-seeded fiber laser incorporated with a fiber Bragg grating external cavity semiconductor laser (FBG-ECL) and a Mach-Zehnder interferometer (MZI) were reported in this paper. The MZI provided a Q-switching with response time in the order of micro-seconds. The FBG-ECL provided narrow pulses as seeds to shorten the Q-switched pulses. Experimentally, pulse width of 0.8 μs was measured, which was one fifth of the pulse width without self-seeding.     

Efficient Tm:YLF laser with a volume Bragg grating recycle pumped by laser diode

By using a pump recycling configuration, we presented a high efficient diode-pumped Tm:YLF laser with a volume Bragg grating. When the incident pump power was 33.1 W, a maximum output power of 11.1 W at 1907.8 nm with full width at half maximum of 0.6 nm was obtained. The slope efficiency with respect to the incident pump power was 44.8%, and the optical-to-optical efficiency was 33.5%. In addition, the VBG-based Tm:YLF laser was employed as a pumping source of Ho:YAG laser, the maximum output power of 4.7 W with a slope efficiency of 67.0% was obtained, corresponding to Tm-to-Ho conversion efficiency of 51.6%.     

Wideband tunable linear-cavity fiber laser source using strain-induced chirped fiber Bragg grating

A novel wideband tunable linear-cavity fiber laser source using strain-induced chirped fiber Bragg grating (FBG) and erbium–ytterbium co-doped fibers is proposed and demonstrated for the first time. The strain-induced chirped FBG, which acts as a partial-reflecting mirror, is achieved by bending a uniform FBG bonded at a slant onto the lateral surface of a simply supported beam. A single wavelength lasing with a maximum wavelength tuning range of 17 nm has been achieved experimentally.     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法，在D形内包层掺Yb3+双包层光纤一端直接写制出Bragg光栅，用作双包层光纤激光器的输出腔镜.试验得到了线宽为0.196nm，波长为1058.2nm，最高输出功率为570mW的稳定激光输出，解决了激光器中模式竞争造成的输出不稳定现象.从速率方程出发，对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析，结果与实验符合很好. 关键词： 双包层光纤光栅 掺Yb3＋双包层光纤激光器 相位掩模 速率方程     

Single-longitudinal-mode erbium-doped fiber laser based on a fiber Bragg grating Fabry-Perot filter

A novel single-longitudinal-mode (SLM) erbium-doped fiber laser with a simple linear cavity based on a fiber Bragg grating Fabry-Perot filter (FBG-FPF) and a narrowband (～0.06 nm) FBG is proposed and demonstrated experimentally. Two uniform FBGs form the FBG-FPF, which has two ultranarrow transmission bands with a bandwidth of 0.12 pm and a wavelength spacing of 0.095 nm. By slightly tuning the central wavelength of the narrowband FBG, SLM lasing at 1549.658 or 1549.563 nm (corresponding to the two transmission peaks of the FBG-FPF) is achieved with a laser output power of ～4 mW, when the pump power is ～75 mW.     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法 ,在D形内包层掺Yb3 双包层光纤一端直接写制出Bragg光栅 ,用作双包层光纤激光器的输出腔镜 .试验得到了线宽为 0 196nm ,波长为 10 5 8 2nm ,最高输出功率为 5 70mW的稳定激光输出 ,解决了激光器中模式竞争造成的输出不稳定现象 .从速率方程出发 ,对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析 ,结果与实验符合很好     

Switchable triple-wavelength erbium-doped fiber laser using a single fiber Bragg grating in polarization-maintaining fiber

A stable and narrow wavelength spacing multiwavelength erbium-doped fiber laser is proposed and demonstrated. The laser can produce simultaneous dual- and triple-wavelength lasing oscillations with a narrow wavelength spacing of less than 0.1 nm via using a single fiber Bragg gratings written in polarization-maintaining (PM) fiber. By adjusting polarization controller, the wavelength spacing of dual-wavelength lasing oscillations can be tuned to as small as 0.032 nm. The maximum amplitude variation for every lasing wavelength is less than 0.5 dB. The room-temperature operation principle is based on the polarization hole burning and deeply saturated effect in an ordinary erbium-doped fiber ring laser (EDFRL). The laser has the advantages of simple all-fiber configuration, low cost, high stability and operating at room temperature.     

Chirped pulse amplification in single mode Tm:fiber using a chirped Bragg grating

We report femtosecond pulse generation and chirped pulse amplification in Tm:fiber. A mode-locked oscillator operating in the soliton regime produced 800 fs pulses with 5 nm spectral bandwidth, at 40 pJ pulse energy. This oscillator seeded a pre-amplifier that utilizes a Raman soliton self-frequency shift to produce wavelength tunable pulses with 3 nJ energy, reduced pulse duration of 150 fs, and increased bandwidth of 30 nm. For further amplification, the pulses were stretched up to 160 ps using a chirped Bragg grating (CBG). Stretched pulses were amplified to 85 nJ after compression in single-mode Tm:fiber and recompressed with the CBG as short as 400 fs. Compressed pulses were coupled into a highly nonlinear tellurite fiber to investigate the potential of this ultrashort pulse 2-μm fiber source as a pump for mid-IR supercontinuum generation.     

A novel dual-wavelength fiber Bragg grating and its application in fiber ring laser

A novel method for fabricating dual-wavelength fiber Bragg gratings (FBGs) by using one phase mask is developed. The method is based on a double-exposure technique. Our technique lends itself to writing gratings with controllable reflectivity and separation of two Bragg wavelengths. A grating with two equal transmission peaks of 20.25 dB is obtained by this method and the separation of the two Bragg wavelengths is about 0.8 nm. With the grating, we demonstrate a dual-wavelength erbium-doped fiber ring laser whose interval of the two peaks is 0.8 nm. The laser's peak powers can get 3.1 mW above and have a good stability.     

Dual-wavelength high-power Yb-doped double-clad fiber laser based on a few-mode fiber Bragg grating

We report a high-power dual-wavelength Yb-doped double-clad fiber laser based on a few-mode fiber Bragg grating (FMFBG). The FMFBG was fabricated by using a piece of fiber in a length of fiber with a cutoff wavelength of 1225 nm, which supported two modes at 1060 nm. The laser was pumped by a fiber pigtailed laser diode working at 915 nm. Single-wavelength, dual-wavelength and triple-wavelength laser oscillations were observed when the fiber laser operated under different low pump powers. However, stable dual-wavelength operation was achieved at higher pump power of 3.9 W and remained unchanged until the output power reached 5.67 W under the maximum available pump power of 10.7 W. The laser wavelengths were centered at 1059.12 and 1060.80 nm with a full-width at half-maximum of 37 and 43 pm, respectively. The signal-to-noise-ratio was greater than 50 dB and the beam quality factor (M²) was about 1.9.     

Tilted fiber Bragg grating sensors

Optical fiber gratings have developed into a mature technology with a wide range of applications in various areas, including physical sensing for temperature, strain, acoustic waves and pressure. All of these applications rely on the perturbation of the period or refractive index of a grating inscribed in the fiber core as a transducing mechanism between a quantity to be measured and the optical spectral response of the fiber grating. This paper presents a relatively recent variant of the fiber grating concept, whereby a small tilt of the grating fringes causes coupling of the optical power from the core mode into a multitude of cladding modes, each with its own wavevector and mode field shape. The main consequence of doing so is that the differential response of the modes can then be used to multiply the sensing modalities available for a single fiber grating and also to increase the sensor resolution by taking advantage of the large amount of data available. In particular, the temperature cross‐sensitivity and power source fluctuation noise inherent in all fiber grating designs can be completely eliminated by referencing all the spectral measurements to the wavelength and power level of the core mode back‐reflection. The mode resonances have a quality factor of 10⁵, and they can be observed in reflection or transmission. A thorough review of experimental and theoretical results will show that tilted fiber Bragg gratings can be used for high resolution refractometry, surface plasmon resonance applications, and multiparameter physical sensing (strain, vibration, curvature, and temperature).