Optimization of dispersive liquid-liquid microextraction and improvement of detection limit of methyl tert-butyl ether in water with the aid of chemometrics

Dispersive liquid-liquid microextraction (DLLME) coupled with gas chromatography-mass spectrometry-selective ion monitoring (GC-MS-SIM) was applied to the determination of methyl tert-butyl ether (MTBE) in water samples. The effect of main parameters affecting the extraction efficiency was studied simultaneously. From selected parameters, volume of extraction solvent, volume of dispersive solvent, and salt concentration were optimized by means of experimental design. The statistical parameters of the derived model were R(2)=0.9987 and F=17.83. The optimal conditions were 42.0 μL for extraction solvent, 0.30 mL for disperser solvent and 5% (w/v) for sodium chloride. The calibration linear range was 0.001-370 μg L(-1). The improved detection limit with the aid of chemometrics was 0.3 ng L(-1). The relative standard deviation (RSD) with n=9 for 0.1 mg L(-1) MTBE in water with and without internal standard was 2.7% and 3.1%, respectively. Under the optimal conditions, the relative recoveries of spiked MTBE in different water samples were in the range of 100-105%.     

双重净化-气相色谱法测定植物油中指示性多氯联苯

为了考察食用油中7种指示性多氯联苯(PCBs)的残留情况,建立了食用油中痕量多氯联苯测定的双重净化-气相色谱法。以乙腈提取样品,提取液浓缩至干后用正己烷溶解,经浓硫酸、硅胶分散固相萃取双重净化后进行气相色谱分析,外标法定量。优化的色谱条件为:HP-5石英毛细管柱(30 m×0.32 mm×0.25 μm)程序升温分离,流速0.8 mL/min,进样量1.00 μL,电子捕获检测器检测。结果表明:在优化的条件下,7种多氯联苯在10~500 μg/L范围内线性良好,相关系数大于0.999,不同基质中的检出限(S/N=3)范围为1.8~8.9 μg/kg,定量限(S/N=10)范围为5.9~29.8 μg/kg。在橄榄油、花生油和棕榈油空白样品中添加10、20、100 μg/kg 3个水平的7种多氯联苯,其加标回收率范围为71.0%~105.5%,相对标准偏差(RSD)范围为4.0%~11.3%。该方法具有操作简便、快速、准确的特点,可用于植物油中指示性多氯联苯残留量的日常检测。     

气相色谱-质谱法测定植物油中8种维生素E及其在芝麻油真伪鉴别方面的应用

建立了气相色谱-质谱（GC-MS）同时测定植物油中α-、β-、γ-、δ-生育酚和α-、β-、γ-、δ-生育三烯酚等8种维生素E的分析方法。植物油样品经甲醇超声提取、浓缩、定容,在分时段选择离子监测（SIM）模式下分离分析,采用外标法进行定量。结果表明,8种维生素E可实现基线分离;在0.01~1 mg/L范围内,所有目标物均呈良好线性关系,相关系数均大于0.99;检出限和定量限分别为0.03~0.25 mg/kg和0.10~0.83 mg/kg;在芝麻油中分别添加10、50和250 mg/kg 3个水平的8种维生素E进行加标试验,平均回收率为87.5%~107.4%,相对标准偏差（RSD）≤ 7.5%。所建立的方法简单、准确、可靠,且灵敏度高,可用于测定植物油中8种维生素E的含量。采用上述方法对芝麻油、大豆油、菜籽油、葵花籽油、花生油、玉米油和棕榈油等7种共75个植物油样品中维生素E的含量进行测定。结果显示,芝麻油与其他6种植物油中的8种维生素E的组成和含量均有显著差异性,因此该方法可作为芝麻油掺入其他植物油的特征鉴定指标。     

Dispersive liquid-liquid microextraction based on solidification of floating organic droplet followed by high-performance liquid chromatography with ultraviolet detection and liquid chromatography-tandem mass spectrometry for the determination of triclosan and 2,4-dichlorophenol in water samples

A novel, simple and efficient dispersive liquid-liquid microextraction based on solidification of floating organic droplet (DLLME-SFO) technique coupled with high-performance liquid chromatography with ultraviolet detection (HPLC-UV) and liquid chromatography-tandem mass spectrometry (LC-MS/MS) was developed for the determination of triclosan and its degradation product 2,4-dichlorophenol in real water samples. The extraction solvent used in this work is of low density, low volatility, low toxicity and proper melting point around room temperature. The extractant droplets can be collected easily by solidifying it at a lower temperature. Parameters that affect the extraction efficiency, including type and volume of extraction solvent and dispersive solvent, salt effect, pH and extraction time, were investigated and optimized in a 5 mL sample system by HPLC-UV. Under the optimum conditions (extraction solvent: 12 μL of 1-dodecanol; dispersive solvent: 300 of μL acetonitrile; sample pH: 6.0; extraction time: 1 min), the limits of detection (LODs) of the pretreatment method combined with LC-MS/MS were in the range of 0.002-0.02 μg L(-1) which are lower than or comparable with other reported approaches applied to the determination of the same compounds. Wide linearities, good precisions and satisfactory relative recoveries were also obtained. The proposed technique was successfully applied to determine triclosan and 2,4-dichlorophenol in real water samples.     

Extraction optimization of polycyclic aromatic hydrocarbons by alcoholic-assisted dispersive liquid-liquid microextraction and their determination by HPLC

A sensitive method for the extraction and determination of polycyclic aromatic hydrocarbons (PAHs) using alcoholic-assisted dispersive liquid-liquid microextraction (AA-DLLME) and HPLC was developed. The extraction procedure was based on alcoholic solvents for both extraction and dispersive solvents. The effective parameters (type and volume of extraction and dispersive solvents, amount of salt and stirring time) on the extraction recovery were studied and optimized utilizing factorial design (FD) and central composite design (CCD). The best recovery was achieved by FD using 2-ethyl-1-hexanol as the extraction solvent and methanol as the dispersive solvent. The results showed that volume of dispersive solvent and stirring time had no effect on the recovery of PAHs. The optimized conditions were 145 μL of 2-ethyl-1-hexanol as the extraction solvent and 4.2% w/v of salt (NaCl) in sample solution. The enrichment factors of PAHs were in the range of 310-325 with limits of detection of 0.002-0.8 ng/mL. The linearity was 0.01-800 ng/mL for different PAHs. The relative standard deviation (RSD) for intra- and inter-day of extraction of PAHs were in the range of 1.7-7.0 and 5.6-7.3, respectively, for five measurements. The method was also successfully applied for the determination of PAHs in environmental water samples.     

Vortex‐assisted liquid–liquid microextraction using a low‐toxicity solvent for the determination of five organophosphorus pesticides in water samples by high‐performance liquid chromatography

Vortex‐assisted liquid–liquid microextraction followed by high‐performance liquid chromatography with UV detection was applied to determine Isocarbophos, Parathion‐methyl, Triazophos, Phoxim and Chlorpyrifos‐methyl in water samples. 1‐Bromobutane was used as the extraction solvent, which has a higher density than water and low toxicity. Centrifugation and disperser solvent were not required in this microextraction procedure. The optimum extraction conditions for 15 mL water sample were: pH of the sample solution, 5; volume of the extraction solvent, 80 μL; vortex time, 2 min; salt addition, 0.5 g. Under the optimum conditions, enrichment factors ranging from 196 to 237 and limits of detection below 0.38 μg/L were obtained for the determination of target pesticides in water. Good linearities (r > 0.9992) were obtained within the range of 1–500 μg/L for all the compounds. The relative standard deviations were in the range of 1.62–2.86% and the recoveries of spiked samples ranged from 89.80 to 104.20%. The whole proposed methodology is simple, rapid, sensitive and environmentally friendly for determining traces of organophosphorus pesticides in the water samples.     

Determination of 11 priority pollutant phenols in wastewater using dispersive liquid—liquid microextraction followed by high-performance liquid chromatography—diode-array detection

Dispersive liquid—liquid microextraction coupled with high-performance liquid chromatography—diode-array detection was applied for the extraction and determination of 11 priority pollutant phenols in wastewater samples. The analytes were extracted from a 5-mL sample solution using a mixture of carbon disulfide as the extraction solvent and acetone as the dispersive solvent. After extraction, solvent exchange was carried out by evaporating the solvent and then reconstituting the residue in a mixture of methanol–water (30:70). The influences of different experimental dispersive liquid—liquid microextraction parameters such as extraction solvent type, dispersive solvent type, extraction and dispersive solvent volume, salt addition, and pH were studied. Under optimal conditions, namely pH 2, 165-μL extraction solvent volume, 2.50-mL dispersive solvent volume, and no salt addition, enrichment factors and limits of detection ranged over 30–373 and 0.01–1.3 μg/L, respectively. The relative standard deviation for spiked wastewater samples at 10 μg/L of each phenol ranged between 4.3 and 19.3% (n = 5). The relative recovery for wastewater samples at a spiked level of 10 μg/L varied from 65.5 to 108.3%.     

Gas chromatography/mass spectrometry of oils and oil binders in paintings

A GC/MS procedure has been developed, optimized, and applied to characterization of oil binders in paintings. The procedure involves hydrolysis of lipids to fatty acids (FAs) and derivatization of FAs to fatty acid methyl esters (FAMEs) by a solution of sodium methanolate in methanol at an elevated temperature. FAMEs are analyzed by temperature-programed GC followed by full-scan MS. Old and dried samples are subjected to extraction of nonpolymerized FAMEs into dichloromethane prior to hydrolysis. The method provides a good repeatability of results and has been applied to the characterization of common plant oils used in paintings, to commercial oil and tempera paints, to model painting samples, and to samples taken from real paintings. The fresh oils and binders can readily be identified and characterized. The ratio of the methyl esters of palmitic and stearic acids can be used to characterize oil binders in old works of art.     

Hollow fiber-mediated liquid-phase microextraction of chemical warfare agents from water

Unambiguous detection and identification of chemical warfare agents (CWAs) and related compounds are of paramount importance from verification point of view of Chemical Weapons Convention (CWC). It requires development of fast, reliable, simple and reproducible sample preparation of CWAs from water which is likely to be contaminated during deliberate or inadvertent spread of CWAs. This work describes development of hollow fiber liquid-phase microextraction (HF-LPME) method for efficient extraction of CWAs (such as sarin, sulfur mustard and their analogues) from water followed by gas chromatography-mass spectrometric analysis. Extraction parameters, such as organic solvent, agitation, extraction time, and salt concentration were optimized. Best recoveries of target analytes were achieved using 1 microL trichloroethylene as extracting solvent, 1000 rpm stirring rate, 15 min extraction time, and 30% NaCl. Excellent precision was observed with less than 7.6% RSD. The limit of detection by HF-LPME was achieved up to 0.1 microg/L at 30% salt concentration.     

Determination of organophosphorous pesticides in the ppq range using a simple solid-phase extraction method combined with dispersive liquid-liquid microextraction

Solid-phase extraction combined with dispersive liquid-liquid microextraction (SPE-DLLME) was applied for the extraction of six organophosphorous pesticides (OPPs) in water samples. The analytes considered in this study were determined by gas chromatography with mass spectrometry and included prophos, diazinon, chlorpyrifos methyl, methyl parathion, fenchlorphos and chlorpyrifos. Several extraction conditions (extraction solvent and elution/dispersion solvents nature, extraction solvent volume, elution solvent volume, water volume and sample volume) were tested for SPE-DLLME with these analytes and the best results were obtained using carbon tetrachloride as the extraction solvent and acetone as the elution/dispersion solvent. Calibration curves for the determination of OPPs in water samples were constructed in the concentration range of 10-100 ng/L. Limits of detection (LODs) ranged from 38 to 230 pg/L values that are below the maximum admissible level for drinking water (100 ng/L). Relative standard deviations (RSD) were between 8.6 and 10.4% for a fortification level of 100 ng/L. At the same fortification level, the relative recoveries (R.R.) of tap, well and irrigation water samples were in the range of 30.2-97.1%.     

A liquid-phase microextraction method, combining a dual gauge microsyringe with a hollow fiber membrane, for the determination of organochlorine pesticides in aqueous solution by gas chromatography/ion trap mass spectrometry

A liquid-phase microextraction (LPME) method has been demonstrated for the extraction and determination of organochlorine pesticides (OCPs) in aqueous solution. The method combines a dual gauge microsyringe with a hollow fiber membrane (LPME/DGM-HF) followed by detection by gas chromatography/ion trap mass spectrometry (GC/ITMS). The advantages include speed, low solvent and sample consumption, simplicity and ease of use. The extraction time, solvent selection, salt concentration and sample stirring rate have been investigated in order to optimize extraction efficiency. The viability is evaluated by measuring the linearity and detection limit of the five OCPs in aqueous solution. Detection linearity for the OCPs has been achieved over a range of concentrations between 1 and 500 microg/L (r2 > 0.930), with a detection limit of 0.1 microg/L for each OCP.     

Optimization of dispersive liquid-liquid microextraction of copper (II) by atomic absorption spectrometry as its oxinate chelate: application to determination of copper in different water samples

In this study a dispersive liquid-liquid microextraction (DLLME) method based on the dispersion of an extraction solvent into aqueous phase in the presence of a dispersive solvent was investigated for the preconcentration of Cu(2+) ions. 8-Hydroxy quinoline was used as a chelating agent prior to extraction. Flame atomic absorption spectrometry using an acetylene-air flame was used for quantitation of the analyte after preconcentration. The effect of various experimental parameters on the extraction was investigated using two optimization methods, one variable at a time and central composite design. The experimental design was performed at five levels of the operating parameters. Nearly the same results for optimization were obtained using both methods: sample size 5 mL; volume of dispersive solvent 1.5 mL; dispersive solvent methanol; extracting solvent chloroform; extracting solvent volume 250 microL; 8-hydroxy quinoline concentration and salt amount do not affect significantly the extraction. Under the optimum conditions the calibration graph was linear over the range 50-2000 muicro L(-1). The relative standard deviation was 5.1% for six repeated determinations at a concentration of 500 microg L(-1). The limit of detection (S/N=3) was 3 microg L(-1).     

复杂基体中痕量多环芳烃分析测定方法的研究进展

介绍了环境样品（水和土壤）以及植物油中痕量多环芳烃的分析检测方法。对样品的预处理过程和分析方法做了评价。采用一些新的预处理方法（包括液相色谱法、固相萃取法、超临界二氧化碳萃取法）,并结合色谱-质谱在线联用分析检测方法能够获得比较理想的分析结果。引用文献52篇。     

Determination of pesticides in water by cone-shaped membrane protected liquid phase microextraction prior to micro-liquid chromatography

A new sample pre-treatment technique termed cone-shaped membrane liquid phase microextraction (CSM-LPME) was developed and combined with micro-liquid chromatography (micro-LC) for the determination of selected pesticides in water samples. Four pesticides (hexaconazole, procymidone, quinalphos and vinclozolin) were considered as target analytes. Several important extraction parameters such as types of extraction solvent, agitation rate, pH value, total exposure time and effect of salt and humic acids were optimized. Enrichment factors of > 50 folds were easily achieved within 20 min of extraction. The analytical data demonstrated relative standard deviations for the reproducibility of the optimized CSM-LPME method ranging from 6.3 to 7.5%. The correlation coefficients of the calibration curves were at least 0.9995 across a concentration range of 2-100 microg/L. The detection limits for all the analytes were found to be in the range of 1.1-1.9 microg/L.     

Trimethylsulfonium hydroxide as derivatization reagent for the chemical investigation of drying oils in works of art by gas chromatography

A procedure for the determination of fatty acids (FA) and glycerol in oils has been developed. The method includes a derivatization step of the FAs into their methyl esters or a transesterification of the triacylglycerols with trimethylsulfonium hydroxide (TMSH), respectively. The analysis is carried out by gas chromatography with parallel flame ionization and mass spectrometric detection. The parameters involved in the transesterification reaction were optimized. Only the stoichiometric ratio of TMSH:total FA amount showed a significant influence on the reaction yield. Relative standard deviations for 10 replicates were below 3% for all FAs studied and their linearity range was 0.5-50 mmol/L, when using heptadecanoic acid as an internal standard. The final procedure was rapid and required little sample handling. It was then tested on fresh oil samples and presented satisfying results, in agreement with previous works.     

漂浮液滴固化分散液液微萃取与高效液相色谱联用检测环境水样中的3种烷基苯酚

建立了漂浮液滴固化分散液液微萃取(DLLME-SFO)方法,以脂肪酸作为萃取剂,以甲醇作为分散剂,与高效液相色谱联用检测了环境水样中3种烷基苯酚。对影响前处理方法的因素进行了详细考察,在最佳萃取条件(60μL萃取剂辛酸、600μL分散剂甲醇、pH值为2.0~8.0、10 mL水样中加入0.5 g NaCl)下,3种烷基苯酚在20~1 500μg/L范围内具有良好的线性关系,相关系数不小于0.998 5,3种目标化合物的检出限为0.45~0.61μg/L,富集倍数为145~169,实际样品中3个水平的加标回收率为80.1%~109.9%。该方法将脂肪酸作为萃取剂,与HPLC联用实现了烷基苯酚的富集与检测,为环境水样中烷基苯酚的检测提供了对环境友好的前处理新方法。     

Isotope dilution gas chromatography with mass spectrometry for the analysis of 4‐octyl phenol, 4‐nonylphenol,and bisphenol A in vegetable oils

By the combination of solid‐phase extraction as well as isotope dilution gas chromatography with mass spectrometry, a sensitive and reliable method for the determination of endocrine‐disrupting chemicals including bisphenol A, 4‐octylphenol, and 4‐nonylphenol in vegetable oils was established. The application of a silica/N‐(n‐propyl)ethylenediamine mixed solid‐phase extraction cartridge achieved relatively low matrix effects for bisphenol A, 4‐octylphenol, and 4‐nonylphenol in vegetable oils. Experiments were designed to evaluate the effects of derivatization, and the extraction parameters were optimized. The estimated limits of detection and quantification for bisphenol A, 4‐octylphenol, and 4‐nonylphenol were 0.83 and 2.5 μg/kg, respectively. In a spiked experiment in vegetable oils, the recovery of the added bisphenol A was 97.5–110.3%, recovery of the added 4‐octylphenol was 64.4–87.4%, and that of 4‐nonylphenol was 68.2–89.3%. This sensitive method was then applied to real vegetable oil samples from Zhejiang Province of China, and none of the target compounds were detected.     

Ultrapreconcentration and determination of organophosphorus pesticides in water by solid‐phase extraction combined with dispersive liquid–liquid microextraction and high‐performance liquid chromatography

Solid‐phase extraction coupled with dispersive liquid–liquid microextraction was developed as an ultra‐preconcentration method for the determination of four organophosphorus pesticides (isocarbophos, parathion‐methyl, triazophos and fenitrothion) in water samples. The analytes considered in this study were rapidly extracted and concentrated from large volumes of aqueous solutions (100 mL) by solid‐phase extraction coupled with dispersive liquid–liquid microextraction and then analyzed using high performance liquid chromatography. Experimental variables including type and volume of elution solvent, volume and flow rate of sample solution, salt concentration, type and volume of extraction solvent and sample solution pH were investigated for the solid‐phase extraction coupled with dispersive liquid–liquid microextraction with these analytes, and the best results were obtained using methanol as eluent and ethylene chloride as extraction solvent. Under the optimal conditions, an exhaustive extraction for four analytes (recoveries >86.9%) and high enrichment factors were attained. The limits of detection were between 0.021 and 0.15 μg/L. The relative standard deviations for 0.5 μg/L of the pesticides in water were in the range of 1.9–6.8% (n = 5). The proposed strategy offered the advantages of simple operation, high enrichment factor and sensitivity and was successfully applied to the determination of four organophosphorus pesticides in water samples.     

Flow injection determination of free fatty acids in vegetable oils using capacitively coupled contactless conductivity detection

A single line flow injection analysis (FIA) method that incorporated a preconcentrator column packed with C(18) particles and capacitively coupled contactless conductivity detector (C(4)D) was developed for the determination of free fatty acid (FFA) in vegetable oils. The carrier stream was methanol/1.5 mM sodium acetate (pH 8) 80:20 (v/v) at a flow rate of 1.0 mL min(-1). Calibration curve was well correlated (r(2)=0.9995) within the range of 1-200 mg L(-1) FFA (expressed as palmitic acid). Sampling rate of 40-60 h(-1) was achieved. Good agreement was found between the standard non-aqueous titrimetry method and the proposed method when applied to the determination of FFA in palm (crude, olein, and refined, bleached and deodorised) and other vegetable (soybean, rice bran, walnut, corn and olive) oils. The proposed method offers distinct advantages over the official method, especially in terms of simplicity, high sampling rate, economy of solvents and sample, offering considerable promise as a low cost automated system that needs minimum human intervention over long periods of time.     

气流吹扫-注射器微萃取-全二维气相色谱法用于原油组分的表征

建立了气流吹扫-注射器微萃取（GP-MSE）与全二维气相色谱/飞行时间质谱（GC×GC/TOFMS）联用分析原油成分的方法。为了找到适用于原油样品分析的GP-MSE条件,用饱和烃混合标准溶液和15种芳烃的混合标准溶液进行了条件优化,得到的最佳条件如下:取样量5 mg、萃取溶剂正己烷20 μ L、载气流速2 mL/min、加热时间3 min、加热温度300 ℃、冷凝温度-2 ℃。处理后的样品在全二维色谱/飞行时间质谱上进样分析,得到了满意结果。方法的检出限为34~93 μg/L,线性相关系数（R²）>0.99,对50种烃类化合物的回收率在82.0%~107.3%之间,相对标准偏差<10%（n=5）。结果表明GP-MSE-GC×GC/TOFMS法是一种新型绿色、高效、灵敏的分析方法,非常适合原油中挥发性与半挥发性组分的分析。