Composition-dependent phase separation effects of organic solar cells using P3HT:PCBM as active layer and chromium oxide as hole transporting layer

Phase separation of the poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) active layer (ATL) was investigated by varying their relative ratio in the organic solar cells (OSCs). With the help of the UV/visible spectrophotometer, optical microscopy and scanning electron microscope, we found that the cluster of PCBM at the interface or surface was affected by Al cathode, the composition of the blends and thermal annealing. The disc-like shape crystals of PCBM substituted for the needle-like ones at higher PCBM compositions at the ATL/Al interface, which led to stronger contacts and bigger contact area. It could make short circuit current density increase, but may affect the blend morphology and result in parallel resistance and open circuit voltage decreased with the PCBM ratio increasing from 40 to 60%. The microstructure of the P3HT:PCBM ATL, determined by the composition dependent phase separation, supported the optimized performance of the OSCs with the composition of 40-50% PCBM.     

Photoinduced degradation of organic solar cells with different microstructures

An in situ measurement setup is established to investigate the photoinduced degradation effects in a controllable inert gas ambient environment for the two different microstructures of poly(3-hexylthiophene)(P3HT) and [6,6]-phenyl-C61-butyricacid methyl ester(PCBM) bulk-heterojunction organic solar cells. The two devices are fabricated with the solvent vapor drying process followed by a thermal annealing(vapor drying device) and only a normal thermal annealing process(control device), respectively. Their power conversion efficiencies(PCEs) and aging features are compared. Their different degradation behaviors in light absorption are confirmed. In addition, irradiation-induced changes in both nanostructure and surface morphology of the P3HT:PCBM blend films treated with two different fabrication processes are observed through scanning electron microscopy and atomic force microscopy. Aggregated bulbs are observed at the surfaces for control devices after light irradiation for 50 h, while the vapor drying devices exhibit smooth film surfaces, and the corresponding device features are not easy to degrade under the aging measurement. Thus the devices having solvent vapor drying and thermal annealing show better device stabilities than those having only the thermal annealing process.     

P3HT:PCBM薄膜成膜过程对聚合物太阳能电池性能的影响

P3HT:PCBM薄膜的快速和缓慢成膜过程能显著的改变异质结聚合物太阳能电池性能.通过调节旋转时间以及薄膜退火前的间隔时间,研究了P3HT:PCBM混合薄膜缓慢生长所需最佳时间.结果表明,在转速800 r·min-1下旋涂薄膜,经过50～80 s的旋涂,接着放置样品薄膜30 min以上,然后再对薄膜进行退火处理,电池效...     

Programming resistive switching memory by a charged capacitor

The performances of bulk-heterojunction (BHJ) solar cells are investigated for time-dependent thermal annealing with different morphology evolution scales, having special consideration for the diffusion and aggregation of fullerene derivative molecules based on blends of poly(3-hexylthiophene):[6,6]-phenyl-C₆₁-butyric acid methyl ester (P3HT:PCBM). Meaningfully, rapid formation of dot-like and needle-like crystalline PCBM structures of a few micrometers up to 60 μm in size is obtained with thermal annealing treatment from 2 to 15 min, which dynamically reflects a fast process of PCBM molecule and cluster aggregation. Upon ultrasonic-assisted processing and annealing treatment, the scale of P3HT crystals is drastically increased in view of X-ray diffraction (XRD) patterns, leading to a high hole mobility. And, the P3HT domains can be gradually converted into larger P3HT crystals approved by the decreased full width at half-maximum in the XRD patterns. Corresponding current–voltage curves are measured in quantity and we propose a model to explain the effect of the crystalline degree of P3HT domains and aggregation of PCBM molecules and clusters on the phase segregation, expressing a viewpoint towards high performance of BHJ solar cells.     

退火气压对于P3HT∶PCBM微观形貌及光伏性能的影响

通过精确设定不同的退火环境气压,实现对P3HT(Poly(3-hexylthiophene -2,5-diyl)与PCBM([6,6]-Phenyl C₆₁ butyric acid methyl ester)体系中聚噻吩结晶度以及共混相分离程度的控制,并在此基础上制备了结构为ITO/PEDOT∶PSS/P3HT∶PCBM/Al的正型光伏器件。在允许的压强设定范围内,器件各项性能参数均随退火环境压强的增大表现出先升高后下降的变化规律,并统一于气压设定为1 500 mTorr时获得最大值。从活性层的紫外-可见(UV-Vis)吸收光谱中发现P3HT在510 nm吸收峰以及550和600 nm肩峰附近的吸收强度随退火气压升高而增大,在气压为1 500 mTorr时达到最高,吸收强度的提升源于聚合物分子π—π堆叠的增加。原子力显微镜(AFM)进一步分析结果表明,高气压环境(>1 000 mTorr)能够促进P3HT∶PCBM共混组分在退火过程中形成较大程度的相分离,而当环境压强合适时(1 500 mTorr)适度的相分离利于聚合物形成良好有序结晶,从而能够提升活性层内部载流子传输能力,保证较高的短路电流与填充因子,制备的器件也因此表现出良好的光伏性能,光电转化效率达到3.56%。     

The improvement of bulk-heterojunction order in polymer photovoltaic device

The blend morphology and vertical arrangement are critical to the performance of organic bulk-heterojunction photovoltaic devices.In the present paper,the authors proposed a new annealing method that controls the blend morphology and vertical arrangement of two materials by means of simultaneously applying external electrical field and violet irradiation on the active layer of poly(3-hexylthiophene) (P3HT) and -phenyl C61-butyric acid methyl ester(PCBM) during annealing process.By using this annealing metho...     

Plasmonic effects and the morphology changes on the active material P3HT:PCBM used in polymer solar cells using Raman spectroscopy

There is no consensus yet that the enhancement effects of plasmonic device are predominantly caused by plasmonic effects or induced morphology changes in the optoelectronic `materials. Herein, we present a detailed Raman characterization of a typical organic P3HT:PCBM system comprising silver nanowires (Ag NWs) with different size, which can simultaneously study the plasmonic effects and the morphology changes. The direct comparison of the Raman spectra of non‐annealed and annealed samples indicates that the morphology of plasmonic samples has changed before annealing and the morphology of plasmonic samples and reference sample after annealing is not distinguishable. This indicates that the interaction between P3HT and Ag NWs with different size can be explained by plasmonic effects after annealing. Moreover, in‐situ Raman spectroscopy is used to study the morphology changes in plasmonic samples with different diameters of Ag NWs during heating process. This method can distinguish the plasmonic effects and morphology changes of plasmonic device. Copyright © 2016 John Wiley & Sons, Ltd.     

Post-fabrication annealing effects on the performance of P3HT:PCBM solar cells with/without ZnO nanoparticles

In this study, P3HT:PCBM organic photovoltaic (OPV) devices, with or without ZnO nanoparticles buffer layer between the photoactive layer (P3HT:PCBM) and the cathode (Al top electrode), were fabricated. The devices were annealed at 145 °C either before or after depositing the top electrode. The objective of this study was to investigate the effects of the ZnO buffer layer and pre-/post-fabrication annealing on the general performance of these devices. The short-circuit current density (J_SC), open-circuit voltage (V_OC) and the external quantum efficiency (EQE) of the OPV devices were improved by the insertion of the ZnO layer and post-fabrication annealing. The post-fabrication annealed devices, with or without the ZnO layer, exhibited higher values of J_SC, V_OC and EQE than those of similar devices annealed before depositing the Al metal. This can be attributed to, among other things, improved charge transport across the interface between the photoactive layer and the Al top electrode as a result of post-annealing induced modification of the interface morphology.     

Effect of solvents on the performance and morphology of polymer photovoltaic devices

In the polymer photovoltaic devices (PVDs), the performance of devices was strongly influenced by region-regularity, number average molecular weight and casting solvents of polymers. In this work, we fabricated p–n bulk-hetero-junction PVDs based on poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C₆₀-butyric acid methyl ester (PCBM) using various solvents such as chloroform (CF), chlorobenzene (CB), dichlorobenzene (DCB), and mixed solvent (CF/CB, CF/DCB). Thin film of active layer with P3HT/PCBM was prepared by spin coating and thermal annealing at 150 °C with fixed thickness about 110 nm by adjusting solution concentration. The crystalline morphology and layered phase for the active layer were studied by atomic force microscopy and X-ray diffraction, respectively. We investigated the performance of solar cells according to different morphology and crystallinity of active layer by various solvent and mixed solvent.     

退火处理ZnPc(OC_8H_(17)OPyCH_3I)_8阴极缓冲层的倒置有机太阳能电池

制备了以Zn Pc(OC8H17OPy CH3I)8为阴极缓冲层、P3HT∶PCBM为有源层的有机太阳能电池。对阴极缓冲层Zn Pc(OC8H17OPy CH3I)8薄膜分别进行了溶剂蒸汽退火和过渡舱惰性气体流退火处理,并利用原子力显微镜(AFM)对缓冲层表面形貌进行了表征。结果表明:这两种退火方法都使缓冲层形貌得以改善。电池效率从2.14%提高到3.76%,电流密度从8.12 m A/cm2提高到10.71 m A/cm2,填充因子从0.45提高到0.61。与传统器件相比,退火处理的阴极缓冲层器件的稳定性也得到了改善,器件寿命延长了1.4倍。这种简单阴极界面处理方法为改善聚合物太阳能电池性能提供了有效途径。     

Controlling structure and morphology of CoPt nanoparticles through dynamical or static coalescence effects

The structure and morphology of 1 to 3 nm size CoPt nanoparticles have been investigated in situ and in real time under different conditions: growth at 500 degrees C or at room temperature (RT) followed by annealing at 500 degrees C. The small-angle x-ray scattering measurements show size and temperature dependent growth mode with particle motions on the surface, while wide-angle scattering results, supported by Monte Carlo simulations, allow structure identification. If icosahedra are systematically detected at the first growth stages at RT, annealing at 500 degrees C yields the decahedral structure from the quasistatic coalescence of icosahedral morphology. Meanwhile, growth at 500 degrees C proceeds by a dynamical coalescence mechanism at the early stage, yielding truncated octahedral cubic structures.     

掺杂石墨烯量子点对P3HT:PCBM太阳能电池性能的影响

为研究掺杂石墨烯量子点(GQDs)对聚合物电池的影响,采用溶剂热法制备了GQDs,掺杂到聚3-己基噻吩和富勒烯衍生物(P3HT∶PCBM)中作光敏层制备了聚合物太阳能电池。掺杂不同浓度的GQDs后,聚合物电池的开路电压和填充因子都比未掺杂器件高。GQDs掺杂质量分数为0.15%时,形成的掺杂薄膜平整、均匀,填充因子提高了17.42%。GQDs经还原后,随还原时间的延长,填充因子FF增大。到45 min时,电池的FF基本稳定,从31.57%提高至40.80%,提高了29.24%。退火后,获得了最佳的掺杂GQDs的聚合物太阳能电池,开路电压Voc为0.54 V,填充因子FF为55.56%,光电转换效率为0.75%。     

不同环境压强下溶剂退火对聚合物太阳能电池性能的影响

通过改变溶剂退火时的环境压强控制溶剂的蒸发速率,在不同压强下进行加压溶剂退火制备了基于聚-3己基噻吩:富勒烯衍生物(P3HT:PCBM)的体异质结聚合物太阳能电池。X射线衍射(XRD)、紫外-可见吸收光谱(UV-Vis)以及原子力显微镜(AFM)的测试结果表明,增大溶剂退火的环境气压改善了薄膜的结晶度,增强了有源层的光吸收,提高了P3HT和PCBM的相分离程度,更有利于激子的解离和载流子传输。与在常压下溶剂退火相比,在2.0 MPa压强下对有源层进行溶剂退火的器件的光电转换效率提高了29%,达到了3.69%。     

Thermal stability of spin valve sensors using artificial Co/Ir based ferrimagnets

Hard-soft spin valve structures have been grown by molecular beam epitaxy on MgO(0 0 1) substrates. The hard magnetic layer consists of an artificial Co/Ir/Co ferrimagnet system (AFi), while a Fe/Co bilayer from the buffer has been used as a soft detection layer. The Fe layer has been grown at 600°C giving rise to a monocrystalline layer with a BCC structure. Consequently, this layer presents a hard and a easy magnetization axis, respectively, along the BCC [1 1 0] and the [1 0 0] directions. The AFi system presents dramatic differences after successive annealing steps up to 350°C. An increase of the GMR from 3% to 3.5% is observed after annealing at 250°C while the coercive field of the AFi and the GMR plateau are strongly reduced. After further annealing at higher temperature the GMR drops down accompanied with a strong decrease in the antiparallel alignment amount in the AFi system. Rutherford back scattering measurements have been performed to investigate the changes in the interface morphology and to correlate it to the magneto-transport properties.     

Preheated solvent exposure on P3HT:PCBM thin film: A facile strategy to enhance performance in bulk heterojunction photovoltaic cells

In this study, we explored the ability of a preheated solvent (methanol) to induce characteristic changes at the organic active layer/metal interface, thereby improving the performance of fabricated organic photovoltaic (OPV) cells composed of poly(3-hexylthiopene) (P3HT) and a [6,6]-phenyl-C₇₁-butyric acid methyl ester (PCBM) photoactive blend. Our results demonstrate that exposure to methanol (at room temperature, or preheated at 45 °C or 65 °C) improves the performance of the fabricated OPV cells. After preheated methanol exposure, the P3HT:PCBM thin films were tested for crystallinity, morphology, mobility, and photovoltaic characteristics. Our results revealed that use of the preheated solvent on the organic active layer significantly influences the micro/nano scale morphology and phase segregation of the P3HT:PCBM thin films, as well as the charge carrier mobility. It is hypothesized that the side chain ordering of P3HT and redistribution of PCBM could be results of the modified active layer. Consequently, OPV cells modified with the methanol preheated at 65 °C exhibited a power conversion efficiency (PCE) of 3.36%, with open-circuit voltage of 0.59 V, short-circuit current density of 13.83 mA/cm², and fill-factor of 0.41. In contrast, the unmodified P3HT:PCBM thin film (without methanol exposure) showed a PCE of only 2.13%.     

Small angle neutron scattering and small angle X-ray scattering studies of platinum-loaded carbon foams

The morphology of carbon nanofoam samples comprising platinum nanoparticles dispersed in the matrix was characterized by small angle neutron scattering (SANS) and small angle X-ray scattering (SAXS) techniques. Results show that the structure of pores of carbon matrix exhibits a mass (pore) fractal nature and the average radius of the platinum particles is about 2.5 nm. The fractal dimension as well as the size distribution parameters of platinum particles varies markedly with the platinum content and annealing temperature. Transmission electron micrographs of the samples corroborate the SANS and SAXS results.      

Annealed Treatment Effect in Poly（3-hexylthiophene）：Methanofullerene Solar Cells

Polymer photovoltaic devices based on poly（3-hexylthiophene） （P3HT） ： [6,6]-phenyl-C61-butyricacid methyl ester （PCBM） 1：1 weight-ratio blend are reported. The effects of various annealing treatments on the device performance are investigated. Thermal annealing shows significant improvement of the device performances. For devices at 130℃ annealing, maximum power conversion efficiency （PCE） of 3.3% and All factor up to 60.3% is achieved under air mass 1.5, 100 m W/cm^2 illumination. We discuss the effect of thermal annealing by the results of ultraviolet-visible absorption spectroscopy （UV-vis）, dark current-voltage curve, atomic force microscopy （AFM）.     

Plasmon enhanced light absorption in bulk heterojunction organic solar cells

Silver nanospheres (Ag NSs) buffer layers were introduced via a solution casting process to enhance the light absorption in poly (3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C61 butyric acid methyl ester (PCBM) bulk heterojunction organic solar cells. These Ag NSs, as surface plasmons, could increase the optical electric field in the photoactive layer whilst simultaneously improving the light scattering. As a result, this buffer layer improves the light absorption of P3HT:PCBM blend and consequently improves the external quantum efficiency (EQE) of organic solar cells. In this work, different sizes of Ag NSs plasmon‐enhanced layer were investigated, with the aim of optimizing the performance of devices. UV‐vis spectrometer measurement demonstrates that the total optical absorption of P3HT:PCBM blend films in the spectral range of 350–650 nm is increased by ～4 and 6% with incorporation of the 20 and 40 nm Ag NSs, respectively. The J_sc was shown to increase by ～21 and 24% for 20 and 40 nm Ag NSs, respectively. This is due to the extra photogenerated excitons by the plasmonic resonance of Ag NSs. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

碳化硅薄膜脉冲激光晶化特性研究

采用XeCl准分子激光对非晶碳化硅(a-SiC)薄膜的脉冲激光晶化特性进行了研究.通过原子力显微镜（AFM）和Raman光谱技术对退火前后薄膜样品的形貌、结构及物相特性进行了分析.结果表明，选用合适的激光能量采用激光退火技术能够实现a-SiC薄膜的纳米晶化.退火薄膜中的纳米颗粒大小随着激光能量密度的增加而增大；Raman谱分析结果显示了退火后的薄膜的晶态结构特性并给出了伴随退火过程存在的物相分凝现象.根据以上结果并结合激光退火特性，对a-SiC的脉冲激光晶化机理进行了讨论. 关键词： 激光退火 晶化 碳化硅     

Correlation between spectroscopic and morphological properties of composite P3HT/PCBM nanoparticles studied by single particle spectroscopy

We report the fabrication and characterization of composite nanoparticles consisting of a conducting polymer, poly-3-hexylthiophene (P3HT), doped with varying amounts of [6,6]-phenyl C61-butyric acid methyl ester (PCBM), a material blend that is commonly applied in bulk heterojunction organic photovoltaic devices (OPVs). Single particle spectroscopy (SPS) studies, where nanoparticles are studied one particle at a time, reveal that these nanoparticles have spectroscopic characteristics consistent with the existence of two types of crystalline nanodomains, one with a higher energy emission at 660 nm and one with a lower energy emission at 720 nm. In addition, the occurrence of emission at lower peak energy increases with increasing PCBM doping levels, and the intensity of the lower energy peak emission increases with respect to the higher energy peak emission as well. These data reveal a PCBM concentration dependent formation of two types of P3HT crystalline nanodomains in P3HT/PCBM composite nanoparticles, where the lower energy crystal structure becomes more favored with higher PCBM concentration. This work provides a molecular scale insight in the correlation between changes in morphology of conjugated polymer materials with different weight percentages of fullerene dopants.