Al掺杂La10(SiO4)6O3的制备及其导电性能

以溶胶-凝胶法在850℃制备了Al掺杂La10(SiO4)6O3,即La10(SiO4)6-x(AlO4)xO3-0.5x(x=0,0.5,1.0,1.5和2.0),通过TG-DTA、XRD、IR和SEM表征,所得产品为磷灰石相。以电化学阻抗谱研究了其导电性能,发现决定电导率大小的因素有两种,一是间隙氧的数量,二是晶胞的大小,两种因素的综合作用,使得Al掺杂0.5时La10(SiO4)5.5(AlO4)0.5O2.75的电导率最大,在700℃时其电导率达到1.88×10-2S·cm-1。氧分压对电导率的研究表明,其主要的电荷载体是O2-离子。     

La10-x(SiO4)6O3-1.5x的合成及其导电性能的研究

利用溶胶-凝胶法在800 ℃合成了硅酸盐氧基磷灰石La10-x(SiO4)6O3-1.5x(x=0,0.17,0.33,0.50和0.67),经XRD表征所得产品为磷灰石相.以电化学阻抗谱研究了硅酸盐氧基磷灰石的导电性能,体系的电导率随着间隙氧和阳离子空位数量的增多而加大,La9.33(SiO4)6O2的电导率较La9.5(SiO4)6O2.25大,是由于前者有较多的阳离子空位所致,700 ℃时La10(SiO4)6O3的电导率为7.98×10-3 S·cm-1,比La9.33(SiO4)6O2的电导率提高了5倍.氧分压从105～1 Pa变化时电导率保持不变,证明硅酸盐氧基磷灰石在较宽的氧分压范围内为O2-导电.     

La10(SiO4)6-x(GaO4)xO3-0.5x的合成及其导电性能

以溶胶-凝胶法合成前驱体, 在950 ℃时烧结制得La10(SiO4)6－x(GaO4)xO3－0.5x (x＝0, 0.5, 1.0, 1.5和2.0)陶瓷样品, 通过TG-DTA, XRD, IR和SEM表征, 所得产品为磷灰石相. 以电化学阻抗谱研究了其导电性能, 发现决定电导率大小的因素有两种, 一是间隙氧的数量, 二是晶胞的大小, 两种因素的综合作用, 使得La10(SiO4)5(GaO4)O2.5的电导率最大, 在700 ℃时其电导率达到4.66×10－2 S•cm－1. 离子迁移数和氧分压对电导率的研究表明, 其主要的电荷载体是O2－离子.     

固体电解质BaxCe0.8Ho0.2O3-α的导电性及其燃料电池性能

用高温固相反应法合成了BaxCe0.8Ho0.2O3-α(x=1.03,1,0.97)系列固体电解质,粉末XRD结果表明,各材料均为钙钛矿型斜方晶单相结构.用交流阻抗谱技术研究了材料在600-1000℃下、湿润氢气和湿润空气气氛中的导电性;研究了它们的氢-空气燃料电池性能:讨论了材料的非化学计量组成对其电性能的影响.结果表明,在600-1 000℃温度范围内、湿润氢气和湿润空气气氛中.该系列材料的电导率随温度和钡离子含量的变化均与以该系列材料为固体电解质的氢-空气燃料电池性能随温度和钡离子含量变化的次序一致,即:非化学计量组成材料BaxCe0.8Ho0.2O3-α(x=1.03,0.97)具有较化学计量组成材料BaxCe0.8Ho0.2O3-α(x=1)高的电导率和氢-空气燃料电池输出功率密度,其中BaxCe0.8Ho0.2O3-α有最高的电导率(1000℃时、在湿润的氢气气氛中:2.10×10-2 S·cm-1;在湿润的空气气氛中:3.46×10-2S·cm-1)和最大的氢-空气燃料电池输出功率密度(1 000℃时:122 mW·cm-2).     

Li2O-Al2O3-GeO2-P2O5微晶玻璃的微观结构和离子电导率

采用传统熔体冷却法制备了Li3-xAl2-xGex(PO4)3(x=1.1~1.9)体系玻璃,并通过热处理工艺获得了高电导率的微晶玻璃。通过XRD、TEM和交流阻抗等测试方法,研究了该系微晶玻璃的物相组成、微观形貌和锂离子电导率。结果表明:该系统微晶玻璃析出导电主晶相为LiGe2(PO4)3,杂质相为AlPO4和GeO2。当x=1.5时,由于导电主晶相LiGe2(PO4)3晶粒充分长大、分布均匀,所制备微晶玻璃的室温锂离子电导率最高(5.72×10-4 S.cm-1),可以满足全固态锂离子电池对电解质高室温电导率的要求。     

钙掺杂对La2-xCaxCe2O7-δ性能影响研究

利用高温固相反应法制备了高温质子导体La2-xCaxCe2O7-δ(0≤x≤0.2)。分别利用X射线衍射(XRD)、扫描电子显微镜(SEM)对试样的相组成、微观形貌进行了表征。并对试样在水蒸气和CO2气氛中的化学稳定性进行了测试。研究了不同掺杂量和不同测试气氛对La2-xCaxCe2O7-δ电性能的影响。实验结果表明:1 500℃烧结的试样均形成萤石型结构;试样在CO2和水蒸气气氛中表现出良好的化学稳定性。试样在湿润氢气气氛下的电导率明显高于干燥空气气氛,x=0.1的试样在湿润氢气气氛中具有最高的电导率,850℃时达到3.16×10-2S.cm-1,电导活化能为84.93 kJ.mol-1。     

Gd1-xSrxCoO3-δ和Gd0.8Sr0.2Co1-yFeyO3-δ系阴极材料的制备和性能

采用甘氨酸-硝酸盐(GNP)法合成了新型中温固体氧化物燃料电池(IT.SOFC)的阴极材料Gd1-xSrxCoO3-δ(x=0-0.5)和Gd.0.8Sr0.2Co1-yFeyO3-δ(y=0-1),所合成的初始粉体在800℃下煅烧12 h后均形成了钙钛矿结构的单相固溶体.研究发现,Gd1-xSrxCoO3-δ(GSC)的电导率在600℃时达到了559 S·cm-1,由Ce0.8Cd0.2O2-δ(GDC)电解质和GSC-25GDC材料组成的对称电极在600℃和700℃的界面阻抗分别为0.170Ω·cm2和0.064Ω·cm2,活化能仅为87.8 kJ·mol-1,预示其可以作为ITSOFC较为理想的阴极备选材料;随着Fe3 离子含量的增加,Gd0.8Sr0.2Co1-yFeyO3-δ系列阴极材料的热膨胀系数显著降低,但其电导率也急速下降;此外,通过调整Gd0.8Sr0.2CoO3-δ与GDC的比例可以制备出热膨胀系数与GDC电解质匹配、性能良好的Cd0.8Sr0.2CoO3-δ/GDC复合阴极材料.     

Ce_(0.8)Nd_(0.2)O_(1.9)-La_(0.95)Sr_(0.05)Ga_(0.9)Mg_(0.1)O_(3-δ)固体复合电解质的结构和电性能

采用溶胶-凝胶法分别制备La0.95Sr0.05Ga0.9Mg0.1O3-δ(LSGM)和Ce0.8Nd0.2O1.9(NDC)电解质,并在NDC溶胶中加入0-15%(w,质量分数)的LSGM预烧粉体制得NDC-LSGM复合电解质,研究不同质量比复合电解质的结构和电性能.采用X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)和X能量色散谱仪(EDS)对样品进行结构表征,交流(AC)阻抗谱测试样品导电性能.结果表明:NDC-LSGM复合体系主要由立方萤石结构相、钙钛矿结构相和杂质相组成;LSGM的添加可促进晶粒的生长,产生大量相界面,清除或降低SiO2有害影响,明显提高晶界导电性;LSGM质量分数为10%的样品NL10具有最高晶界电导率和总电导率,400°C时NL10的晶界电导率σgb和总电导率σt分别为12.15×10-4和3.49×10-4S cm-1,与NDC的σgb(1.41×10-4S cm-1)和σt(1.20×10-4S cm-1)相比分别提高了7.62和1.91倍,总电导率的提高主要归因于晶界电导率的影响.     

钒改性锂离子电池正极材料LiFe0.5Mn0.5PO4/C 电化学性能

采用高温固相反应,以NH4VO3为钒源合成了化学计量式为(1-x)LiFe0.5Mn0.5PO4-xLi3V2(PO4)3/C(x=0,0.1,0.2,0.25,1)的钒改性磷酸锰铁锂正极材料.电化学测试表明钒改性能明显提高磷酸锰铁锂材料的充放电性能,其中x=0.2时得到的0.8LiFe0.5Mn0.5PO4-0.2Li3V2(PO4)3/C(标记为LFMP-LVP/C)材料电化学性能最好,其0.1C倍率时的放电比容量为141mAh·g-1.X射线衍射(XRD)分析指出LFMP-LVP/C材料的微观结构为橄榄石型LiFe0.5Mn0.5PO4/C和NASICON型Li3V2(PO4)3组成的双相结构.能量色射X射线谱(EDS)分析结果指出,Fe、Mn、V、P元素在所合成材料中的分布非常均匀,表明所制备材料成分的均一性.Li3V2(PO4)3改性使材料的电导率明显提高.LiFe0.5Mn0.5PO4的电导率为1.9×10-8S·cm-1,而LFMP-LVP材料电导率提高到2.7×10-7S·cm-1.与纯Li3V2(PO4)3的电导率(2.3×10-7S·cm-1)相近.电化学测试表明钒改性使LFMP-LVP/C材料充放电过程电极极化明显减小,从而电化学性能得到显著提高.本文工作表明Li3V2(PO4)3改性可成为提高橄榄石型磷酸盐锂离子电池正极材料电化学性能的一种有效方法.     

钒改性锂离子电池正极材料LiFe0.5Mn0.5PO4/C电化学性能

采用高温固相反应,以NH4VO3为钒源合成了化学计量式为(1-x)LiFe0.5Mn0.5PO4-xLi3V2(PO4)3/C (x=0,0.1,0.2,0.25,1)的钒改性磷酸锰铁锂正极材料.电化学测试表明钒改性能明显提高磷酸锰铁锂材料的充放电性能,其中x=0.2时得到的0.8LiFe0.5Mn0.5PO4-0.2Li3V2(PO4)3/C(标记为LFMP-LVP/C)材料电化学性能最好,其0.1C倍率时的放电比容量为141 mAh·g-1.X射线衍射(XRD)分析指出LFMP-LVP/C材料的微观结构为橄榄石型LiFe0.5Mn0.5PO4/C和NASICON型Li3V2(PO4)3组成的双相结构.能量色射X射线谱(EDS)分析结果指出,Fe、Mn、V、P元素在所合成材料中的分布非常均匀,表明所制备材料成分的均一性.Li3V2(PO4)3改性使材料的电导率明显提高.LiFe0.5Mn0.5PO4的电导率为1.9×10-8 S· cm-1,而LFMP-LVP材料电导率提高到2.7×10-7 S·cm-1.与纯Li3V2(PO4)3的电导率(2.3×10-7 S·cm-1)相近.电化学测试表明钒改性使LFMP-LVP/C材料充放电过程电极极化明显减小,从而电化学性能得到显著提高.本文工作表明Li3V2(PO4)3改性可成为提高橄榄石型磷酸盐锂离子电池正极材料电化学性能的一种有效方法.     

Simulation of dielectric properties and stability of clusters (H2O)i, CO2(H2O)i, and CH4(H2O)i

Molecular dynamics method is used for studying complex permittivity ɛ and the stability of individual water clusters as a function of the number of involved molecules (7 ≤ i ≤ 20) and also the corresponding characteristics of water aggregates with a captured CO₂ or CH₄ molecule. Absorption of the latter molecules leads to considerable changes in dielectric properties and stability of clusters. In particular, upon the addition of a CO₂ molecule to a water cluster, the oscillation parameters of the real and imaginary parts of the permittivity change. Capture of a CH₄ molecule by a water aggregate changes the ɛ(ω) dependence from the relaxation to resonance type. For i ≥ 15, the thermal stability of individual water clusters can be lower than that of aggregates CO₂(H₂O) _i and CH₄(H₂O) _i . The mechanical stability of (H₂O) _{i ≥ 13} clusters can exceed that of heteroclusters under consideration. Clusters (H₂O) _i and CO₂(H₂O) _i have approximately the same dielectric stability, whereas aggregates CH₄(H₂O) _i exhibit lower stability with respect to electric perturbations. Original Russian Text ? A.E. Galashev, V.N. Chukanov, A.N. Novruzov, O.A. Novruzova, 2007, published in Elektrokhimiya, 2007, Vol. 43, No. 2, pp. 143–153.     

Negative hyperconjugation in methyl and silyl anions and its effect on the acidities of CH(4-n)Fn CH(4-n)C1n SiH(4-n)Fn and SiH(4-n)Cln

Group separation reactions calculated using an ab intio molecular orbital calculation at the MP4/6-31 + + G(d,p) level of theory, show the negative hyperconjugation between fluorine atoms to be larger in methanes than in silanes. Stabilisation due to negative hyperconjugation is larger in anions than in identically substituted neutral molecules, e.g. 43.1 kcal mol⁻¹ in CF₃⁻ compared with 26.7 kcal mol⁻¹ in CHF₃. By contrast, in chloro-substituted methanes, silanes, methyl anions and silyl anions, group separation energies are approximately zero, indicating no appreciable negative hyperconjugation. An -chloro substituent is more effective than an -fluoro one at delocalising the negative charge of an anion and, as a consequence, the chloromethanes and chlorosilanes are all more acidic than the identically substitued fluoromethanes and fluorosilanes. For chloro-substituted molecules the acidity is linearly dependent on the number of chlorine atoms; for fluoro-substituted molecules stabilisation by negative hyperconjugation results in each additional fluorine atom increasing the acidity by larger increments.     

Synthesis and X-ray crystal structures of [Ru4H4(CO) 11(PPh3)] and [Ru4−x IrxH2−x(CO) 12(PPh3) ] (x = 0 or 1)

Three tetranuclear clusters [Ru₄H₄(CO)₁₁(PPh₃)] (1), [Ru₄H₂(CO)₁₂(PPh₃)] (2) and [Ru₃IrH(CO)₁₂(PPh₃)] (3) were formed in the reaction of [Ir(CO)Cl(PPh₃)₂] and Na[Ru₃H(CO)₁₁] in tetrahydrofuran. Complexes 1–3 were characterized by IR and ¹H and ³¹P NMR, and the structure of the clusters was confirmed by single crystal X-ray analysis. In 2 and 3 one of the carbonyls bridges between two ruthenium atoms; otherwise the compounds contain only terminal carbonyls.     

Interconverting WW Triple Bonds and W4 Clusters: Structures of W4(OPrn)16 and [Li2W2(OPrn)8(DME)]2*

Alcoholysis of W₂(NMe₂)₆ with excess n-propanol in hexane yields the tetranuclear cluster, W₄(OPrⁿ, I. Reduction of I with two equivalents of Li₂COT in THF gives a small yield of Li₂W₂(OPrⁿ)₈. Single crystals were isolated by cooling the product mixture in DME and were shown to be [Li₂W₂(OPrⁿ)₈(DME)]₂, II, which consists of a unique “dimer of dimers” structure. In this reaction sequence, W₄¹⁶⁺ cluster formation is followed by four electron reduction to reform the (W≡W)⁶⁺ unit. Better yields of the lithium salt can be obtained by the addition of LiOPrⁿ/HOPrⁿ solutions to W₂(OBu^t)₆ in which case Li₂W₂(OPrⁿ)₈ has been obtained as a 1:1 adduct with LiOPr. This identity of this salt was confirmed by solution NMR spectroscopy. In the alternative reaction, the (W≡W)⁶⁺ center remains intact from reactant to product. No attempt has been made to separate the product from excess LiOPr. DFT (ADF 2004.01) molecular orbital calculations on the model cluster W₄(OH)₁₆ are used to help elucidate the disruption of the W₄ cluster upon four electron reduction. The molecular structures of compounds I and II are reported.*Dedicated to Professor F. A Cotton on the occasion of his 75th birthday.     

Efficient UV-emitting X-ray phosphors: octahedral Zr(PO4)6 luminescence centers in potassium hafnium–zirconium phosphates K2Hf1−xZrx(PO4)2 and KHf2(1−x)Zr2x(PO4)3

Potassium hafnium–zirconium phosphates, K₂Hf_1−xZr_x(PO₄)₂ and KHf_2(1−x)Zr_2x(PO₄)₃, are broad-band UV-emitting phosphors. At room temperature, they have emission peak maxima at approximately 322 and 305 nm, respectively, under 30 kV peak molybdenum X-ray excitation. Both phosphors demonstrate luminescence efficiencies that make them up to 60% as bright as commercially available CaWO₄ Hi-Plus. The solid-state and flux synthesis conditions, and X-ray excited UV luminescence of these two phosphors are discussed. Even though the two compounds have different atomic structures, they contain zirconium in the same active luminescence environment as that found in highly efficient UV-emitting BaHf_1−xZr_x(PO₄)₂. All the three materials have hafnium and zirconium in octahedral coordination via oxygen-atom corner sharing with six separate PO₄ tetrahedra. This octahedral Zr(PO₄)₆ moiety appears to be an important structural element for efficient X-ray excited luminescence, as are the edge-sharing octahedral TaO₆ chains for tantalate emission.     

[{Pt4(en)4(NHCOtBu)4}{Tl(18-crown-6)}2](PF6)6的合成与晶体结构

The compound [{Pt₄(en)₄(NHCO^tBu)₄}{Tl(18-crown-6)}₂](PF₆)₆ has been synthesized by a simple one-pot multicomponent reaction. Its structure was determined by X-ray single crystal diffraction analysis. The cation of the compound consists of one linearly arranged [Pt₄(en)₄(NHCO^tBu)₄]⁴⁺ chain and two [Tl(18-crown-6)]⁺ ions located at the two ends of the platinum chain. The complex crystallizes in a triclinic P1 with a=1.060 5(1), b=1.252 3(1), c=2.015(2) nm, α=107.430(2)°, β=91.032(2)°, γ=101.910(2)°, V=2.489 6(4) nm³, Z=2, R₁=0.074 4, wR₂(I>2σ(I))=0.222 5, S=1.062. CCDC: 294083.     

Global minima of (C60)nCa, (C60)nF and (C60)nI clusters

Likely candidates for the lowest potential energy minima of (C₆₀)_nCa²⁺, (C₆₀)_nF⁻ and (C₆₀)_nI⁻ clusters are located using basin-hopping global optimisation. In each case, the potential energy surface is constructed using the Girifalco form for the C₆₀ intermolecular interaction, an averaged Lennard–Jones C₆₀–ion interaction, and a polarisation potential, which depends on the first few non-vanishing C₆₀ multipole polarisabilities. We find that the ions generally occupy the interstitial sites of a (C₆₀)_n cluster, the coordination shell being tetrahedral for Ca²⁺ and F⁻. The I⁻ ion has an octahedral coordination shell in the global minimum for (C₆₀)₆I⁻, however for 12  n  8 the preferred coordination geometry is trigonal prismatic.     

Matrix-Inducing Synthesis of SrxY10?x(SiO4)y(PO4)6?yO2: Eu3+ Micron Crystalline Coral Like Phosphors by Sol-Gel Composition of Hybrid Precursors

In the context, Sr_xY_10−x(SiO₄)_y(PO₄)_6−yO₂ doped with 1 mol%Eu³⁺ (x = 2, y = 6; x = 4, y = 4; x = 5, y = 3; x = 8, y = 0) were synthesized by using 3-aminopropyl-triethoxysilane (APES) as the sources of the silicate network. X-ray diagrams confirm that Sr_xY_10−x(SiO₄) _y(PO₄)_6−yO₂: Eu³⁺ solid solutions are formed as a pure apatitic phase. The SEM picture shows that there exist some novel unexpected coral like morphological structures. The luminescent intensity is the strongest for the host composition of Sr₄Y₆(SiO₄)₄(PO₄)₂O₂ although the effect of the composition on the luminescent intensity is little.     

Ti掺杂对(LaMn1-xTixO3)0.67(NiMn2O4)0.33(0≤x≤0.7)陶瓷材料微结构及电性能影响

采用氧化物固相法制备(LaMn1-xTixO3)0.67(NiMn2O4)0.33系列NTC(Negative temperature coefficient)复合热敏电阻材料。利用TG/DSC、激光粒度分析、XRD、SEM、阻-温特性和老化性能测试等手段,确定了粉体煅烧温度,表征了粉体的颗粒尺寸、陶瓷体的物相、形貌及其电学特性、稳定性等与Ti掺杂量的关系。结果表明:在1 200~1 300℃烧结温度范围内,(LaMn1-xTixO3)0.67(NiMn2O4)0.33复合体系的电阻率ρ25℃随Ti含量的增加而显著增加;电阻率ρ25℃和B值变化范围分别为4.4~53 179Ω.cm、1 357~3 998 K。125℃下老化1 000 h阻值变化率ΔR/R0均小于0.51%。该复合体系电阻率、B值调整范围较大,稳定性好,是一种具有实际应用价值的NTC热敏电阻材料。     

Ba3 (VO4)2-K2 Ba(MoO4)2 and Pb3 (VO4)2-K2 Pb(MoO4)2 systems

Phase equilibria in the Ba₃(VO₄)₂-K₂Ba(MoO₄)₂ and Pb3(VO₄)₂-K₂Pb(MoO₄)₂ systems have been investigated. In the first system, a continuous series of substitutional solid solutions with the palmierite structure is formed, and in the second one, the polymorphic transition in lead orthovanadate at 100°C restricts the extent of the palmierite-type solid solution to 10–100 mol % K₂Pb(MoO₄)₂. Original Russian Text ? V.D. Zhuravlev, Yu.A. Velikodnyi, A.S. Vinogradova-Zhabrova, A.P. Tyutyunnik, V.G. Zubkov, 2008, published in Zhurnal Neorganicheskoi Khimii, 2008, Vol. 53, No. 10, pp. 1746–1748.