Oxygen electroreduction on anthraquinone-modified nickel electrodes in alkaline solution

The electrochemical reduction of oxygen has been studied on anthraquinone (AQ) modified nickel electrodes in 0.1 M KOH solution using the rotating disk electrode (RDE) technique. Modification of the Ni electrode surface with AQ by electrochemical reduction of the corresponding diazonium salt was carried out in two different media (in acetonitrile and in aqueous acidic solution). The AQ-modified Ni electrodes showed a good electrocatalytic activity for O₂ reduction. The RDE data indicate that the reduction of oxygen on Ni/AQ electrodes proceeds by a two-electron pathway in alkaline solution. The O₂ reduction results obtained for Ni/AQ electrodes are compared with those of AQ-modified glassy carbon electrodes.     

Catalase‐Modified Carbon Electrodes: Persuading Oxygen To Accept Four Electrons Rather Than Two

We successfully exploited the natural highly efficient activity of an enzyme (catalase) together with carbon electrodes to produce a hybrid electrode for oxygen reduction, very appropriate for energy transformation. Carbon electrodes, in principle, are cheap but poor oxygen reduction materials, because only two‐electron reduction of oxygen occurs at low potentials, whereas four‐electron reduction is key for energy‐transformation technology. With the immobilization of catalase on the surface, the hydrogen peroxide produced electrochemically is decomposed back to oxygen by the enzyme; the enzyme natural activity on the surface regenerates oxygen, which is further reduced by the carbon electrode with no direct electron transfer between the enzyme and the electrode. Near full four‐electron reduction of oxygen is realised on a carbon electrode, which is modified with ease by a commercially available enzyme. The value of such enzyme‐modified electrode for energy‐transformation devices is evident.     

纳米碳管作为氧扩散电极催化层第二相碳载体的电极特性

A novel gas diffusion electrode using binary carbon supports (carbon nanotubes and active carbon) as the catalyst layer was prepared. The electrochemical properties for oxygen reduction reaction (ORR) in alkaline electrolyte were investigated by polarization curves and electrochemical impedance spectroscopy. The results show that the binary-support electrode exhibits higher electrocatalytic activity than the single-support electrode, and the best performance is obtained when the mass ratio of carbon nanotubes and activated carbon is 50 ∶50. The results from their electrode kinetic parameters indicate that the introduction of carbon nanotubes as a secondary support provides high accessible surface area, good electronic conductivity and fast ORR kinetics. The electrocatalytic activity of binary-support electrodes is obviously improved by the deposition of Pt nanoparticles on carbon nanotubes, even at very low Pt loading (45.7 μg/cm2). In addition, the EIS analysis results show that the process of ORR may be controlled by diffusion of oxygen in the thin film for binary-support electrodes with or without Pt catalyst.     

超氧自由基电化学发生体系的研究

超氧自由基是人体内氧代谢的重要产物 [1 ] .迄今为止 ,超氧自由基的研究方法有电子自旋共振法、光度法和电化学法等 [2～ 5] .其中 ,通过电化学还原氧产生超氧自由基是一种简便快捷的方法 [6,7] .本文使用长链表面活性剂 DSAB作为疏水分子 ,比较了强碱性介质中氧在汞电极和 4种非汞电极上的电化学还原行为 ,建立了超氧自由基在非汞电极 (铂电极 )上电化学发生新体系 .通过石英晶体微天平和计时电量法进一步证实了超氧自由基的产生 ,并用循环伏安法比较了抗坏血酸和半胱氨酸两种抗氧化剂对超氧自由基的清除能力 .1　实验部分1.1　试剂与仪…     

Electrochemical Properties of Carbon Black AD-100 and AD-100 Promoted with Pyropolymer of Cobalt Tetra(p-methoxyphenyl)porphyrin

Carbon black AD-100: initial, activated, and promoted with pyropolymer of cobalt tetra(p-methoxyphenyl)porphyrin is characterized by a complex of electrochemical (floating electrode, rotating disk electrode, rotating ring-disk electrode, electrochemical impedance) and structural (standard porosimetry, BET) methods of investigation. Procedures for the AD-100 activation and promotion and the preparation of thin layers of the material to be studied and deposited on disk electrodes are described. The effect of the activation and promotion of carbon black on the surface and electrocatalytic activity of materials under study in the reduction of oxygen and hydrogen peroxide is shown. The ratio of constants of oxygen reduction directly to water and through intermediate formation of hydrogen peroxide is determined. A path for the oxygen reduction is discussed.     

Blocking properties of gold electrodes modified with 4-nitrophenyl and 4-decylphenyl groups

The electrochemical properties of Au electrodes grafted with 4-nitrophenyl and 4-decylphenyl groups have been studied. The electrografting of gold electrode surface with aryl groups was carried out by electroreduction of the corresponding diazonium salts in acetonitrile. The nitrophenyl film growth on gold was examined by atomic force microscopy, electrochemical quartz crystal microbalance and X-ray photoelectron spectroscopy. These measurements showed that a multilayer film of nitrophenyl groups was formed. Cyclic voltammetry was used to study the blocking properties of aryl-modified gold electrodes towards the Fe(CN)₆^3−/4− redox system. The reduction of oxygen was strongly suppressed on these electrodes as evidenced by the rotating disc electrode results.     

Electrocatalytic Reduction of Oxygen at Glassy Carbon Electrodes Coated with Diazonium‐derived Porphyrin/Metalloporphyrin Films

In this study, the influence of the film structure was investigated on the electrocatalytic oxygen reduction at GC electrodes covered with porphyrin and metalloporphyrin rings via the diazonium modification method. For that purpose, primarily, tetraphenylporphyrin (TPP) films on GC electrode surfaces were prepared by electroreduction of in situ generated diazonium salts of 5‐(4‐aminophenyl)‐10,15,20‐triphenylporphyrin (APP) and 5,10,15,20‐tetrakis(4‐aminophenyl)porphyrin (TAPP) molecules. Next, the formation of metalloporphyrin films on the modified surfaces was accomplished through the complexation reactions of surface porphyrin rings with metal ions in the salt solutions containing Mn(II), Fe(III) and Co(II) ions. The resulting porphyrin and metalloporphyrin layers were identified with XPS and ICP‐MS. The electrochemical barrier properties of the films on GC surfaces were examined by cyclic voltammetry in K₃Fe(CN)₆ aqueous solution. The electrocatalytic abilities of the resulting films were also investigated for the oxygen electrochemical reduction by employing cyclic voltammetry in PBS solutions saturated with oxygen. The results showed that the oxygen reduction potentials on modified GC electrodes were shifted to less negative potentials compared to that of bare GC electrode. Also, it was obtained that the oxygen reduction reaction was more effective on the GC electrodes modified with TPP rings by using TAPP molecules than those prepared by using APP molecules.     

Electropolymerization of iron tetra(<Emphasis Type="Italic">o</Emphasis>-aminophenyl)porphyrin from aqueous solution and the electrocatalytic behavior of modified electrode

Stable electroactive iron tetra(o-aminophenyl)porphyrin (FeTAPP) films are prepared by electropolymerization from aqueous solution by cycling the electrode potential between −0.4 and 1.0 V vs Ag/AgCl at 0.1 V s⁻¹. The cyclic voltammetric response indicates that polymerization takes place after the oxidation of amino groups, and the films could be produced on glassy carbon (GC) and gold electrodes. The film growth of poly(FeTAPP) was monitored by using cyclic voltammetry and electrochemical quartz crystal microbalance. The cyclic voltammetric features of Fe(III)/Fe(II) redox couple in the film resembles that of surface confined redox species. The electrochemical response of the modified electrode was found to be dependent on the pH of the contacting solution with a negative shift of 57 mV/pH. The electrocatalytic behavior of poly(FeTAPP) film-modified electrode was investigated towards reduction of hydrogen peroxide, molecular oxygen, and chloroacetic acids (mono-, di-, and tri-). The reduction of hydrogen peroxide, molecular oxygen, and dichloroacetic acid occurred at less negative potential on poly(FeTAPP) film compared to bare GC electrode. Particularly, the overpotential of hydrogen peroxide was reduced substantially. The O₂ reduction proceeds through direct four-electron reduction mechanism.     

Carbon nanotubes as a secondary support of a catalyst layer in a gas diffusion electrode for metal air batteries

In this paper, we report the use of binary carbon supports (carbon nanotubes (CNTs) and active carbon) as a catalyst layer for fabricating gas diffusion electrodes. The electrocatalytic properties for the oxygen reduction reaction (ORR) were evaluated by polarization curves and electrochemical impedance spectroscopy (EIS) in an alkaline electrolyte. The binary-support electrode exhibits better performance than the single-support electrode, and the best performance is obtained when the mass ratio of carbon nanotubes and active carbon is 50:50. The results from the electrode kinetic parameters indicate that the introduction of carbon nanotubes as a secondary support provides high accessible surface area, good electronic conductivity, and fast ORR kinetics. Furthermore, the effect of CNT support on the electrocatalytic properties of Pt nanoparticles for binary-support electrodes was also investigated by different loading-reduction methods. The electrocatalytic activity of the binary-support electrodes is improved dramatically by Pt loading on CNT carbon support, even at very low Pt loading. Additionally, the EIS analysis results indicate that the process of ORR may be controlled by diffusion of oxygen in the electrode thin film for binary-support electrodes with or without Pt catalyst.     

电位调控制备还原氧化石墨烯的电催化性能研究

本文通过控制电位还原氧化石墨烯,可控制备不同含氧官能团的石墨烯纳米材料。以多巴胺、[Fe(CN)_6]~(3-)、NADH为电活性探针,研究了石墨烯表面含氧官能团、缺陷、表面荷电性质以及导电性等对石墨烯电催化性能的影响。研究发现,低还原程度的氧化石墨烯表面含有大量缺陷和丰富的官能团,能够促进多巴胺自催化反应,也有利于K_3[Fe(CN)_6]在电极表面的电子转移;随着氧化石墨烯还原程度提高,其导电性逐渐得到改善,且其表面官能团和缺陷位点数量逐渐减少,对NAD~+的吸附变弱,因而能促进NADH发生电催化氧化。     

苯甲酸在疏水性复合电极上的电化学还原行为

以铜片和锌片为基材,复合电镀制得Cu-PTFE(聚四氟乙烯)和Zn-PTFE疏水性复合电极,并将复合电极应用于苯甲酸的电化学还原行为研究。测定了复合电极在电解液中的Tafel极化曲线、循环伏安、电极稳定性和交流阻抗等电化学参数。结果表明,在苯甲酸电还原制备苯甲醛中,Cu-PTFE复合电极相对于Zn-PTFE复合电极具有较高的催化活性,其电还原产率分别为88.4%和79.2%,因此,Cu-PTFE复合电极有望成为苯甲酸电化学还原制备苯甲醛的电极材料。电化学行为的研究结果显示,苯甲酸在疏水性复合电极上的电还原过程可能只受电子迁移过程控制。     

Oxygen reduction at the surface of glassy carbon electrodes modified with anthraquinone derivatives and dyes

The preparation, electrochemical and catalytic behaviour of glassy carbon electrodes modified by anthra-9,10-quinone, its amino derivatives and dyes were investigated. The stability of the modified electrodes was studied by cyclic voltammetry in acidic and neutral media. The electrocatalytic ability of the modified electrodes for the reduction of dioxygen to hydrogen peroxide was examined by cyclic voltammetry, chronoamperometry and chronocoulometry techniques. The influence of pH on the electrochemical and catalytic behaviour was studied and pH 5.0–8.0 was chosen as the optimum working pH by comparing the shift in oxygen reduction potential. The anthraquinone-adsorbed glassy carbon electrodes possess excellent electrocatalytic abilities for dioxygen reduction with overpotential ranging from 280 to 560 mV lower than that at a plain glassy carbon electrode. Hydrodynamic voltammetric studies were performed to determine the heterogeneous rate constants for the reduction of O₂ at the surface of the modified electrodes, mass specific activity of the anthraquinones used and the apparent diffusion coefficient of O₂ in buffered aqueous O₂-saturated solutions. Studies showed the involvement of two electrons in dioxygen reduction.     

Transport effects in the oxygen reduction reaction on nanostructured, planar glassy carbon supported Pt/GC model electrodes

The role of transport and re-adsorption processes on the oxygen reduction reaction (ORR), and in particular on its selectivity was studied using nanostructured model electrodes consisting of arrays of Pt nanostructures of well-defined size and separation on a planar glassy carbon (GC) substrate. The electrochemical measurements were performed under controlled transport conditions in a double-disk electrode thin-layer flow-cell configuration; the model electrodes were fabricated by colloidal lithography techniques, yielding Pt nanostructures of well defined and controlled size and density (diameter: 140 or 85 nm, height: 20 or 10 nm, separation: from 1-2 to more than 10 diameters). The nanostructured model electrodes were characterized by scanning electron microscopy and electrochemical probing of the active surface area (via the hydrogen adsorption charge). The electrocatalytic measurements revealed a pronounced variation of the hydrogen peroxide yield, which increases by up to two orders of magnitude with increasing separation and decreasing size of the Pt nanostructures. Similar, though less pronounced effects were observed upon varying the electrolyte flow and thus the mass transport characteristics. These effects are discussed in a reaction model which includes (i) direct reduction to H(2)O on the Pt surface and (ii) additional H(2)O(2) formation and desorption on both Pt and carbon surfaces and subsequent partial re-adsorption and further reduction of the H(2)O(2) molecules on the Pt surface.     

The use of auger electron spectroscopy for the characterisation of the surfaces of spherical gold electrodes

Gold spheres (1.5 mm diameter) were obtained from wires of different purities by melting under various conditions (nature and pressure of the atmosphere used, sputtering and transfer conditions to the Auger spectroscope). Their surfaces were analysed by Auger electron spectroscopy (AES) as regards conditions of preparation. The main impurities detected were sulphur, carbon and oxygen, the latter appeared to be bonded to oxidizable elements such as silicon, calcium or even iron for the less pure samples. The origin of the surface contaminants has been investigated (bulk metal impurities, air pollutants, emission from the inner surface of pyrex tube used for melting, annealing and sputtering). Spheres of known surface condition were used as electrodes. The shape of differential capacity-potential curves obtained just after the electrode was dipped into the electrolyte was in good agreement with expectation based on previous AES analysis. Other gold electrodes were analysed by AES after various electrochemical treatments. Oxygen appeared to be stable under AES vacuum conditions on the surface of an electrochemically oxidized electrode. Such oxidized gold surfaces did not adsorb carbon compounds and sulphur unlike those which were reduced. Metallic impurities were not detected by AES on electrochemically reduced gold electrodes which did not retain oxygen from previous electro-oxidizing treatments. In this case oxygen traces observed by AES which amounted to random values according to the electrochemical treatment, seemed to be assignable to cumulative contribution of oxidized impurities not detected individually by AES.     

铂电极上锑吸附原子对1,2-丙二醇电催化氧化性能的影响

运用电化学循环伏安(CV)和电化学原位石英晶体微天平(EQCM)研究了Pt电极表面不可逆吸附Sb原子的电化学特性以及Pt电极上Sb吸附原子对0.1mol·L-1H2SO4溶液中1,2 丙二醇电催化氧化性能的影响.研究发现,当扫描电位的上限Eu≤0.50V(SCE)时,Sb可以稳定地吸附在Pt电极表面,饱和覆盖度为0.34;通过控制电位扫描上限和扫描圈数剥离部份Sb可方便地得到Sbad的不同覆盖度;Pt电极表面Sb吸附原子能在较低的电位下吸附氧,可显著提高1,2 丙二醇电催化氧化活性.与Pt电极相比较,Sb饱和吸附原子修饰的Pt电极使1,2 丙二醇氧化的峰电流增加了近2倍.作者还从表面质量变化提供了吸附原子电催化作用的新数据.     

活性炭表面性质对氧气扩散电极电催化性能的影响

 分别采用硝酸和空气氧化处理制得具有不同表面性质的粉末活性炭,并以此为催化层材料制成炭基氧气扩散电极,测定了不同电极的极化曲线和电化学阻抗谱. N2物理吸附和He程序升温脱附(He-TPD)研究表明,硝酸处理对活性炭孔结构的影响较小,但可使其表面含氧基团明显增加; 而空气氧化处理则会导致活性炭的中孔面积和孔容显著增大,但对表面含氧基团的影响较小. 极化曲线和电化学阻抗谱研究发现,当活性炭的孔结构相近时,电极的催化性能随着表面含氧基团的增多而急剧下降; 当活性炭表面含氧基团的量相近时,中孔孔容增大将导致电极催化性能的恶化. 与活性炭表面含氧基团相比,孔结构对氧气扩散电极的电化学性能具有更显著的影响.     

Pt及其修饰电极上甲醇吸附和氧化的CV和EQCM研究

运用电化学循环伏安和石英晶体微天平 (EQCM )研究了 0 .1mol·L- 1H2 SO4 溶液中甲醇在Pt电极和以Sb ,S不可逆吸附原子修饰的Pt(Pt/Sbad和Pt/Sad)电极上的吸附和氧化过程 .结果表明甲醇的氧化与电极表面氧物种有着极其密切的关系 .Pt电极表面Sb吸附原子能在较低的电位下吸附氧 ,可显著提高甲醇电催化氧化活性 .与Pt电极相比较 ,Sb吸附原子修饰的Pt电极使甲醇氧化的峰电位负移了 0 .13V .相反 ,Pt电极表面S吸附原子的氧化会消耗表面氧物种 ,抑制了甲醇的电氧化 .本文从表面质量变化提供了吸附原子电催化作用的新数据     

Electrochemical behaviour of oxygen reduction on polymer carbon electrodes in alkaline media

The preparation of polymer carbon electrocatalysts by the controlled pyrolysis of polyfurfuryl alcohol polymer is described. The potentiostatic method was used to study the electrochemical behaviour of the oxygen reduction reaction on the prepared catalyst electrodes in potassium hydroxide electrolyte. A pure polymer carbon electrode and a cobalt chloride doped polymer carbon electrode were shown to be active in oxygen reduction, but the electrode containing cobalt chloride seemed the most active. The main reaction product at the pure polymer electrode is hydrogen peroxide, involving two electrons, whereas at a poly(CoCl₂) electrode the reduction process reaches partly its ultimate state, and involves at most three electrons.     

Application of electrochemical reactors for industrial waste-water treatment

The effectiveness of electrochemical reactors for industrial wastewater treatment has been improved since three-dimensional electrodes have been introduced; in fact, limitations of mass transfer can arise, due to the low concentrations of pollutants which may be involved in the process. Three-dimensional electrodes offer a very high electrode area per unit electrode volume and they can act as turbulence promoters or give rise to high linear electrolyte velocity, resulting in high values of mass transport coefficient. However, careful selection of operative parameters is needed in order to obtain high performance. This paper examines the results obtained in our laboratory on the cathodic reduction of copper at RVC electrodes; in particular the interference of dissolved oxygen is studied during the removal of copper from extremely diluted solutions (C < 10 ppm). Some results are also discussed on the removal of organic pollutants by electrochemical oxidation at three-dimensional anode consisting of a fixed bed of carbon pellets.     

Pt／C气体扩散电极制备方法的探索

Ｐｔ／Ｃ气体扩散电极制备方法的探索马永林（青海教育学院,青海,西宁８１０００８）以Ｐｔ／Ｃ为电催化剂的气体扩散电极的制备方法是直接影响该电极电化学性能的重要因素。一般的制备方法是基于将Ｐｔ／Ｃ电催化剂和聚四氟乙烯以及某些有机物或表面活性剂的糊状物涂布...