Voltammetric determination of N-acetylcysteine using a carbon paste electrode modified with copper(II) hexacyanoferrate(III)

The preparation and electrochemical characterization of a carbon paste electrode modified with copper(II) hexacyanoferrate(III) (CuHCF) as well as its behavior as electrocatalyst toward the oxidation of N-acetylcysteine were investigated. The electrochemical behavior of the modified electrode and the electrooxidation of N-acetylcysteine were explored using sweep linear voltammetry. The best voltammetric response was observed for a paste composition of 20% (w/w) copper(II) hexacyanoferrate(III) complex, acetate buffer solution at pH of 6.0 as the electrolyte and scan rate of 10 mV s^− 1. A linear voltammetric response for N-acetylcysteine was obtained in the concentration range from 1.2 × 10^− 4 to 8.3 × 10^− 4 mol L^− 1, with a detection limit of 6.3 × 10^− 5 mol L^− 1. The proposed electrode is useful for the quality control and routine analysis of N-acetylcysteine in pharmaceutical formulations.     

Oxidative degradation of non-ionic surfactant (TritonX-100) by chromium(VI)

Degradation of polyoxyethylene chain of non-ionic surfactant (TritonX-100) by chromium(VI) has been studied spectrophotometrically under different experimental conditions. The reaction rate bears a first-order dependence on the [Cr(VI)] under pseudo-first-order conditions, [TritonX-100]  [Cr(VI)] in presence of 1.16 mol dm⁻³ perchloric acid. The observed rate constant (k_obs) was 3.3 × 10⁻⁴ to 3.5 × 10⁻⁴ s⁻¹ and the half-life (t_1/2) was 33–35 min for chromium(VI). The effects of total [TritonX-100] and [H⁺] on the reaction rate were determined. Reducing nature of non-ionic TritonX-100 surfactant is found to be due to the presence of –OH group in the polyoxyethylene chain. It was observed that monomeric and non-ionic micelles of TritonX-100 were oxidized by chromium(VI). When [TritonX-100] was less than its critical micelle concentration (cmc) the k_obs values increased from 0.76 × 10⁻⁴ to 1.5 × 10⁻⁴ s⁻¹. As the [TritonX-100] was greater than the cmc, the k_obs values increases from 2.1 × 10⁻⁴ to 8.2 × 10⁻⁴ s⁻¹ in presence of constant [HClO₄] (1.16 mol dm⁻³) at 40 °C. A comparison was made of the oxidative degradation rates of TritonX-100 with different metal ion oxidants. The order of the effectiveness of different oxidants was as follows: permanganate > diperiodatoargentate(III) > chromium(VI) > cerium(IV).     

Mesoporous silica functionalized with diethylenetriamine moieties for metal removal and thermodynamics of cation–basic center interactions

The inorganic–organic hybrid material was synthesized by co-condensation of tetraethylorthosilicate and the organosilane N-[3-(trimethoxysilyl)propyl]diethylenetriamine. Spectroscopic analysis of the hybrid material by FTIR showed bands at 2937 and 2839 cm⁻¹ related to ν(CH); ²⁹Si NMR spectrum gave signals at −108, −99, −68 and −59 ppm, Q⁴, Q³, T⁴ and T² species related to the silica backbone structure. The well-defined peaks obtained in the ¹³C NMR spectrum in the 10–58 ppm region confirmed the attachment of organic functional groups as pendant chains bonded into the porous silica. Particle morphology evaluated by a scanning electron microscopic (SEM) study showed the formation of spherical particles in the nanometer range. The X-ray diffraction pattern showed a peak at a 2θ of 2.3°, demonstrating the mesoporous characteristic of the synthesized material. Adsorption evaluated by batch equilibrium processes gave the maximum adsorption of 2.2 and 2.8 mmol g⁻¹ for copper and nickel, respectively. From these values a stoichiometry of 2:1 for cation/ligand was established, considering the amount of 1.2 mmol of pendant groups per gram of the hybrid material. Thermodynamic parameters related to the adsorption of metal ions, evaluated using the calorimetric titration technique presented a negative Gibbs free energy value, in agreement with the spontaneity of cation removal on the basic center in the mesoporous silica at the solid/liquid interface.     

Calorimetric determination of enthalpy changes for the proton ionization of N-tris(hydroxymethyl)methyl-4-aminobutanesulfonic acid (TABS), N-tris(hydroxymethyl)methyl-3-aminopropanesulfonic acid (TAPS) and 3-[N-tris(hydroxymethyl)methylamino]-2-hyroxypropane sulfonic acid (TAPSO) in water–methanol mixtures

Enthalpies for the two proton ionizations of the biochemical buffers N-tris(hydroxymethyl)methyl-4-aminobutanesulfonic acid (TABS), N-tris(hydroxymethyl)methyl-3-aminopropanesulfonic acid (TAPS) and 3-[N-tris(hydroxymethyl)methylamino]-2-hyroxypropane sulfonic acid (TAPSO) were obtained in water–methanol mixtures with methanol mole fraction (X_m) from 0 to 0.360. The ionization enthalpy for the first proton (ΔH₁) of all three buffers was small and exhibited slight changes upon methanol addition. The ionization enthalpy of the second proton (ΔH₂) of TABS increased from 39.6 to 49.8 kJ mol⁻¹ and for TAPS from 40.1 to 43.2 kJ mol⁻¹, with a minimum of 38.2 kJ mol⁻¹ at X_m = 0.059. For TAPSO the increase was from 33.1 to 35.6 kJ mol⁻¹ at X_m = 0.194, with measurements at higher X_m precluded by low solubility of TAPSO in methanol rich solvents. The solvent composition was selected so as to include the region of maximum structure enhancement of water by methanol. The results were interpreted in terms of solvent–solvent and solvent–solute interactions.     

Dinitrogen and carbon monoxide hydrogen bonding in protonic zeolites: Studies from variable-temperature infrared spectroscopy

Adsorption (at a low temperature) of nitrogen on the protonic zeolite H-Y results in hydrogen bonding of the adsorbed N₂ molecules with the zeolite Si(OH)Al Brønsted-acid groups. This hydrogen-bonding interaction leads to activation, in the infrared, of the fundamental N–N stretching mode, which appears at 2334 cm⁻¹. From infrared spectra taken over a temperature range, the standard enthalpy of formation of the OH···N₂ complex was found to be ΔH⁰ = −15.7(±1) kJ mol⁻¹. Similarly, variable-temperature infrared spectroscopy was used to determine the standard enthalpy change involved in formation of H-bonded CO complexes for CO adsorbed on the zeolites H-ZSM-5 and H-FER; the corresponding values of ΔH⁰ were found to be −29.4(±1) and −28.4(±1) kJ mol⁻¹, respectively. The whole set of results was analysed in the context of other relevant data available in the literature.     

Modeling of Equilibrium Adsorption and Surface Tension of Cationic Gemini Surfactants

A series of equilibrium tension models are used to evaluate the adsorption behavior of a novel class of lipoaminoacid gemini cationic surfactants, N^α,N^ω-bis(long-chain N^α-acylarginine)α,ω-dialkylamides or bis(Args). For purposes of comparison, the monomer LAM (the methyl ester of N^α-lauroyl arginine) was also examined. These surfactants are of particular interest for both their low toxicity and biocompatibility. The tension models are based on the Gibbs adsorption isotherm and classified as “ionic” when the surface charge and the electric double layer are accounted for or as “pseudo-nonionic” when the surface charge is ignored. Both model predictions and fitted parameter values are evaluated with respect to physical plausibility and overall goodness of fit to the available tension and density data. In particular, the inferred values for the standard Gibbs free energy of adsorption ΔG°, determined from an equilibrium constant defined on a nondimensional basis, without including artifacts due to an electrostatic contribution, are analyzed. The most reliable values of ΔG° are found with the combined model to range from −110 to −120 kJ mol⁻¹ for the three dimers examined and −80 kJ mol⁻¹ for the monomer. For spacer chain lengths n=3, 6, or 9, the maximum surface area of surfactant adsorption and the maximum free energy of adsorption are observed for the surfactant with the spacer chain length of 6.     

New functional triethoxysilanes as iodide sources for dye-sensitized solar cells

Three new triethoxysilanes bearing quaternary ammonium alkyl iodides are reported, N,N,N-triethyl-3-(triethoxysilyl)propan-1-aminium iodide 1, N,N,N-triheptyl-3-(triethoxysilyl)propan-1-aminium iodide 2 and N,N,N-tridodecyl-3-(triethoxysilyl)propan-1-aminium iodide 3. ¹H and ¹³C NMR spectroscopy and electrospray mass spectrometry were used to confirm the synthesis of pure products. Electrolytes based on these ionic liquids were developed and their performance in dye-sensitized solar cells (DSSCs) evaluated. The electrolytes incorporated 1 and 2 (in 30–60 wt%) as iodide sources together with I₂ (0.08 M), 0.1 M guanidinium thiocyanate and 0.5 M tert-butylpyridine in acetonitrile (AN); and I₂ (0.15 M) and N-methylbenzimidazole (0.5 M) for 2-methoxyproprionitrile (MPN) as co-solvent. Testing of DSSCs to analyze the influence of chain length (ethyl and heptyl) on cell efficiency revealed that, for silanes concentration of 1 M, electrolyte B (based on 2 in AN) and electrolyte C (based on 1 in MPN) gave the best cell efficiency at simulated full sunlight (AM 1.5, 1000 W m⁻²) illumination (5.0–5.3%). At 0.1 Sunlight (AM 1.5, 100 W m⁻²), electrolyte B gave the best performance of 8.0%. High open circuit voltages (V_OC) of 750–850 mV were achieved for a number of quite efficient cells (5–6%). For silane 2, variation of the I⁻/I₂ ratio and total silane content (1–2 M 2) on DSSC efficiency gave a consistent efficiency of 8.0% at 0.1 Sunlight. At full sunlight, the cell efficiency decreased as the silane concentration increased from 1 M (5.0%) to 2 M (3.7%), largely due to a drop in short circuit current.     

The standard partial molar entropy of the aqueous tetra-n-butylammonium cation

The standard partial molar entropy of the aqueous tetrabutylammonium cation, not known previously, has now been obtained, based on the molar entropy of two of its crystalline salts, the iodide and the tetraphenylborate, recently determined experimentally for this purpose. The calculation required also published molar enthalpies of solution and solubilities of these two salts as well as of the perchlorate. The choice of the anions depended mainly on the limited solubilities of the examined salts in water, facilitating the estimation of the relevant activity coefficients. The result is S^∞(Bu₄N⁺, aq) = (380 ± 20) J · K⁻¹ · mol⁻¹ at T = 298.15 K, on the mol · dm⁻³ scale and based on S^∞(H⁺, aq) = (−22.2 ± 1.2) J · K⁻¹ · mol⁻¹ (yielding the ‘absolute’ value). The molar entropy of this cation in the ideal gas standard state, S(Bu₄N⁺, g) = (798 ± 8) J · K⁻¹ · mol⁻¹ then yielded the molar entropy of hydration Δ_hydS^∞ (Bu₄N⁺) = (−418 ± 23) J · K⁻¹ · mol⁻¹.     

Mesoporous MnO2 as enzyme immobilization host for amperometric glucose biosensor construction

Mesoporous MnO₂ (mesoMnO₂) is synthesized facilely through sol–gel process using nonionic surfactant polyxyethylene fatty alcohol (AEO₉) as template. Transmission electron microscopy (TEM) image and N₂ adsorption/desorption isotherm show that the obtained mesoMnO₂ material presents disordered porous structure and appropriate pore size suitable for the immobilization of glucose oxidase (GOx). An amperometric glucose biosensor based on GOx entrapped in mesoMnO₂ is fabricated, in which mesoMnO₂ also acts as a catalyst for the electrochemical oxidation of H₂O₂ produced by enzyme reaction. The biosensor shows fast and sensitive current response to glucose in the linear range of 0.0009–2.73 mM. The response time (t_95%) is less than 7 s. The sensitivity and detection limit are 24.2 μA cm⁻² mM⁻¹ and 1.8 × 10⁻⁷ M (S/N = 3), respectively. This indicates that mesoMnO₂ has promising application in enzyme immobilization and biosensor construction.     

Solvatochromic studies of interactions between surfactants and poly(N-substituted acrylamide)s

Interactions between poly(N-substituted acrylamide)s and surfactants, such as sodium dodecyl sulfate (SDoS) and sodium decyl sulfate (SDeS), in aqueous solutions were investigated using a solvatochromic probe. The polymers used were poly(N,N-dimethylacrylamide) (PDMA), poly(N-isopropylacrylamide) (PIPA), poly(N-acryloylpyrrolidine) (PAPR), and poly(vinylpyrrolidone) (PVPy) for comparison. They were labeled with pyridinium dicyanomethylide chromophore as a solvatochromic probe, and the changes in the microenvironment polarity of the polymer upon association with surfactant micelles were investigated by monitoring the λ_max in the absorption spectra of the probe molecule. It was found that the Gibbs free energy of micelle stabilization by polymer complexation for SDoS is 7.6, 4.1, and 2.2 kJ mol⁻¹, and for SDeS 5.1, 2.9, and 0.8 kJ mol⁻¹ with PIPA, PAPR, and PDMA, respectively. These results indicate that the complexation between polymer and surfactant is influenced not only by the alkyl-chain length of the surfactant, but also by the polymer side groups.     

Temperature dependence vapour pressure measurements of Mg(tmhd)2(tmeda) [(tmhd = 2,2,6,6-tetramethyl-3,5-heptanedione, tmeda = N,N,N′,N′-tetramethylethylenediamine]

The reaction between the magnesium β-diketonate complex Mg(tmhd)₂(H₂O)₂ and 1 equiv. of N,N,N′,N′-tetramethylethylenediamine (tmeda = Me₂NCH₂CH₂NMe₂) in hexane at room temperature yielded Mg(tmhd)₂(tmeda). The standard enthalpy of sublimation (83.2 ± 2.3 kJ mol⁻¹) and entropy of sublimation (263 ± 6.3 J mol⁻¹ K⁻¹) of Mg(tmhd)₂(tmeda) were obtained from the temperature dependence vapour pressure, determined by adopting a horizontal dual arm single furnace thermogravimetric analyser as a transpiration apparatus. From the observed melting point depression DTA, the standard enthalpy of fusion (58.3 ± 5.2 kJ mol⁻¹) was evaluated, using the ideal eutectic behaviour of Mg(tmhd)₂(tmeda) as a solvent with bis(2,4-pentanedionato)magnesium(II), Mg(acac)₂ as a non-volatile solute.     

Development and critical comparison of greener flow procedures for nitrite determination in natural waters

Two greener procedures for flow-injection spectrophotometric determination of nitrite in natural waters were developed and critically compared. Replacement of toxic reagents, waste minimization and treatment were exploited to attend the standards of clean chemistry. The flow system was designed with solenoid micro-pumps in order to minimize reagent consumption and waste generation. The first procedure is based on the Griess diazo-coupling reaction with sulfanilamide and N-(1-naphthyl)ethylenediamine (NED) yielding an azo dye, followed by photodegradation of the low amount of waste generated based on the photo-Fenton reaction. The second procedure is based on the formation of iodine from nitrite and iodide in acid medium in order to avoid the use of toxic reagents. For Griess method, linear response was achieved up to 1.0 mg L^− 1, described by the equation A = − 0.007 + 0.460C (mg L^− 1), r = 0.999. The detection limit was estimated as 8 μg L^− 1 at the 99.7% confidence level and the coefficient of variation was 0.8% (n = 20). The sampling rate was estimated as 108 determinations per hour. The consumption of the most toxic reagent (NED) is reduced 55-fold and 20-fold in comparison to batch method and flow injection with continuous reagent addition, respectively. A colorless residue was obtained by in-line photodegradation with reduction of 87% of the total organic carbon content. The results obtained for natural water samples were in agreement with those achieved by the reference method at the 95% confidence level. For the nitrite–iodide method, linear response was observed up to 2.0 mg L^− 1, described by the equation A = − 0.024 + 0.148C (mg L^− 1), r = 0.999. The detection limit was estimated as 25 μg L^− 1 at the 99.7% confidence level and the coefficient of variation was 0.6% (n = 20). The sampling rate was estimated as 44 determinations per hour. Despite avoiding the use of toxic reagents, the nitrite–iodide method presented worst performance in terms of selectivity and sensitivity.     

Study on dynamic interfacial tension of 3-dodecyloxy-2-hydroxypropyl trimethyl ammonium bromide at liquid/liquid interface

Dynamic interfacial tension between aqueous solutions of 3-dodecyloxy-2-hydroxypropyl trimethyl ammonium bromide (R₁₂HTAB) and n-hexane were measured using the spinning drop method. The effects of the R₁₂HTAB concentration (the concentration below the CMC) and temperature on the dynamic interfacial tension have been investigated; the reason of the change of dynamic interfacial tension with time has been discussed. The effective diffusion coefficient, D_a, and the adsorption barrier, _a, have been obtained from the experimental data using the extended Word–Tordai equation. The results show that the dynamic interfacial tension becomes smaller while _a becomes higher with increasing R₁₂HTAB concentration in the bulk aqueous phase. D_a decreases from 5.56 × 10⁻¹² m⁻² s⁻¹ to 0.87 × 10⁻¹² m⁻² s⁻¹ while _a increases from 5.41 kJ mol⁻¹ to 7.74 kJ mol⁻¹ with the increase of concentration in the bulk solution of R₁₂HTAB from 0.5 × 10⁻³ mol dm⁻³ to 4 × 10⁻³ mol dm⁻³. Change of temperature affects the adsorption rate through altering D_a and _a. The value of D_a increases from 5.56 × 10⁻¹² m⁻² s⁻¹ to 13.98 × 10⁻¹² m⁻² s⁻¹ while that of _a decreases from 5.41 kJ mol⁻¹ to 5.07 kJ mol⁻¹ with temperature ascending from 303 K to 323 K. The adsorption of surfactant from the bulk phase into the interface follows a mixed diffusion–activation mechanism, which has been discussed in the light of interaction between surfactant molecules, diffusion and thermo-motion of molecules.     

Investigation of silicate mineral sanidine by vibrational and NMR spectroscopic methods

Sanidine, a variety of feldspar minerals has been investigated through optical absorption, vibrational (IR and Raman), EPR and NMR spectroscopic techniques. The principal reflections occurring at the d-spacings, 3.2892, 3.2431, 2.9022 and 2.6041 Å confirm the presence of sanidine structure in the mineral. Sanidine shows five prominent characteristic infrared absorption bands in the region 1200–950, 770–720, 590–540 and 650–640 cm⁻¹. The Raman spectrum shows the strongest band at 512 cm⁻¹ characteristic of the feldspar structure, which contains four membered rings of tetrahedra. The UV–vis–NIR absorption spectrum had strong absorption features at 6757, 5780 and 5181 cm⁻¹ due to the combination of fundamental OH– stretching. The bands at 11236 and 8196 cm⁻¹and the strong, well-defined band at (30303 cm⁻¹ attest the presence of Fe²⁺ and Fe³⁺, respectively, in the sample. The signals at g = 4.3 and 3.7 are interpreted in terms of Fe³⁺ at two distinct tetrahedral positions Tl and T2 of the monoclinic crystal structure The ²⁹Si NMR spectrum shows two peaks at −97 and −101 ppm corresponding to T2 and T1, respectively, and one peak in ²⁷Al NMR for Al(IV).     

Synthesis and spectroscopic properties of a new bipyridine-bipyrazoyl(pyridine)-thiocyanato-ruthenium(II) complex

The complex [Ru(II)(dcbpyH₂)(bdmpp)NCS](PF₆) (1) (where dcbpyH₂ is 2,2′-bipyridine-4,4′-dicarboxylic acid, bdmpp is 2,6-bis(3,5-dimethyl-N-pyrazoyl)pyridine,) is synthesized and characterized extensively by ¹H NMR and ¹³C NMR 1D and 2D, mass spectroscopy, cyclic voltammetry, electronic absorption spectroscopy and IR. The half-wave potential of the Ru(II)/Ru(III) redox couple was measured at E_1/2=+0.795 V versus Ag/AgCl in CH₃CN. The complex presents three intense metal-to-ligand charge transfer (MLCT) (d_M→π_L*) absorption bands centered at 383 (=21 300 M⁻¹ cm⁻¹), 432 (=22 400 M⁻¹ cm⁻¹) and 475 nm (=23 400 M⁻¹ cm⁻¹), respectively. The absorbance is extremely strong between 400 and 500 nm and even at 620 nm, the extinction coefficient is still high (=3768 M⁻¹ cm⁻¹). The strong π-acceptor property of the trans-isothiocyanate ligand compared with the Cl⁻ ligand is probably the cause of the blue-shift observed in complex 1. These properties make the complex potentially promising for the photosensitization process. The incorporation of TiO₂ photoelectrodes derivatized with this complex into a solar cell using a composite polymer/inorganic oxide solid-state electrolyte confirmed its sensitizing ability. Incident monochromatic photon-to-current conversion efficiency (IPCE) values of about 30% and overall energy conversion efficiency (η) of 1.7% were obtained.     

Comparative studies on hydrolysis of bis(p-nitrophenyl) phosphate catalyzed by short- and long-alkyl-multiamine metallomicelles

Four short- and long-alkyl-multiamine ligands L¹–L⁴ have been synthesized and characterized. The catalytic efficiency of complex CuL¹ and functional metallomicelles CuL²–CuL⁴ were comparatively investigated for the hydrolysis of bis(p-nitrophenyl) phosphate (BNPP) in buffered solution at 30 °C. The ternary kinetic model for metallomicellar catalysis was suggested to analyze the experimental data. The kinetic and thermodynamic parameters k^′_N, K_T and pK_a were obtained. The results indicated that the complexes with 1:1 ratio of ligands L²–L⁴ to copper(II) ion were the kinetic active catalysts, and the deprotonized Cu(II) complex formed by activated water molecule was the real active species for BNPP catalytic hydrolysis. The real rate constant of the reaction catalyzed by CuL¹–CuL⁴ was 4.00 × 10⁻⁶, 7.44 × 10⁻⁵, 1.42 × 10⁻⁴ and 4.10 × 10⁻⁴ s⁻¹, respectively. The effects of ligand and microenvironment on the hydrolytic reaction of BNPP have been discussed in detail.     

Semi-empirically derived petrophysical and thermodynamical coefficients of permselective shales—Implications on ore mineralization

Phenomenological coefficients of shale–electrolyte systems may offer a glimpse into probable matrix-permeability and solute-exclusionary relationships. Shales from unexposed Upper Cretaceous Period Mancos Shale and from Permian Period Abo Formation were cut into thin wafers, placed in custom built osmometers and a chemical potential applied across them giving rise to induced osmotic flow. This in turn spawned matrix unique constants namely mechanical filtration coefficient L_P (m³ N⁻¹ s⁻¹), diffusional mobility per unit osmotic pressure L_PD (m³ N⁻¹ s⁻¹), osmotic flow coefficient; L_D (m³ N⁻¹ s⁻¹), reflection coefficient σ (dimensionless) at zero gradients of temperature and hydrostatic pressure. Considering intrinsic relationships between these constants where and L_PD = −σL_P, we have ascertained that the bentonitic fossiliferous Mancos shale had a lower L_P and a higher σ compared to the kaolinitic and siliceous shale from Abo Formation indicating a higher degree of compaction post-diagenesis (lower porosity) and higher filtration efficiency. Mechanistic processes involved in solute transport and matrix morphology indicate key multi-scale transformations, ionic- and atomic-exchange competitions on high energy sites like cation-exchange sites, isomorphic substitution at argillaceous mineral edges, atomic-clipping within basal spacing, preferential pathway migration, dead-end pores that give rise to localized solute exclusionary processes and solute attenuation giving rise to anomalous osmotic gradients.     

An unprecedented Cu–Schiff base complex existing as two different trinuclear units with strong antiferromagnetic couplings

A new tetradentate N₂O₂ donor Schiff base ligand [OHC₆H₄CHNCH₂CH₂CH(CH₂CH₃)NCHC₆H₄OH = H₂L ] was obtained by 1:2 condensation of 1,3-diaminopentane with salicylaldehyde and has been used to synthesise an unusual copper(II) complex whose asymmetric unit presents two structurally different almost linear trinuclear units [Cu₃(μ-L)₂(ClO₄)₂] [Cu₃(μ-L)₂(H₂O)(ClO₄)₂] (1). The ligand and the complex were characterised by elemental analysis, FT-IR, ¹H NMR and UV–Vis spectroscopy in addition electrochemical and single crystal X-ray diffraction studies were performed for the complex. The magnetic properties of 1 reveal the presence of strong intra-trimer (J₁ = −202(3) cm⁻¹ and J₂ = −233(3) cm⁻¹) as well as very weak inter-trimer (zJ′ = −0.11(1) cm⁻¹) antiferromagnetic interactions.     

One-step fabrication of three-dimensional porous calcium carbonate–chitosan composite film as the immobilization matrix of acetylcholinesterase and its biosensing on pesticide

This work reports on a novel nanosized calcium carbonate–chitosan (nanoCaCO₃–chi) composite film fabricated by a one-step co-electrodeposition method. The generated nanoCaCO₃-based matrix possessed a three-dimensional (3D) porous, network-like structure, providing a favorable and biocompatible microenvironment to immobilize enzyme. By using such a composite film as enzyme immobilization matrix, a highly sensitive and stable acetylcholinesterase (AChE) sensor was achieved for determination of methyl parathion as a model of organophosphate pesticides (OPs) compounds. The inhibition of methyl parathion was proportional to its concentration ranging from 0.005–0.2 to 0.75–3.75 μg mL⁻¹. The detection limit was found to be as low as 1 ng mL⁻¹ (S/N = 3). The designed biosensor exhibited good reproducibility and acceptable stability.     

Palladized aluminum electrode covered by Prussian blue film as an effective transducer for electrocatalytic oxidation and hydrodynamic amperometry of N-acetyl-cysteine and glutathione

The mediated oxidation of N-acetyl cysteine (NAC) and glutathione (GL) at the palladized aluminum electrode modified by Prussian blue film (PB/Pd–Al) is described. The catalytic activity of PB/Pd–Al was explored in terms of Fe^III[Fe^III(CN)₆]/Fe^III[Fe^II(CN)₆]¹⁻ system by taking advantage of the metallic palladium layer inserted between PB film and Al, as an electron-transfer bridge. The best mediated oxidation of NAC and GL on the PB/Pd–Al electrode was achieved in 0.5 M KNO₃ + 0.2 M potassium acetate of pH 2. The mechanism and kinetics of the catalytic oxidation reactions of the both compounds were monitored by cyclic voltammetry and chronoamperometry. The charge transfer-rate limiting step as well as overall oxidation reaction of NAC or GL is found to be a one-electron abstraction. The values of transfer coefficients α, catalytic rate constant k and diffusion coefficient D are 0.5, 3.2 × 10² M⁻¹ s⁻¹ and 2.45 × 10⁻⁵ cm² s⁻¹ for NAC and 0.5, 2.1 × 10² M⁻¹ s⁻¹ and 3.7 × 10⁻⁵ cm² s⁻¹ for GL, respectively. The modifying layers on the Pd–Al substrate have reproducible behavior and a high level of stability in the electrolyte solutions. The modified electrode is exploited for hydrodynamic amperometry of NAC and GL. The amperometric calibration graph is linear in concentration ranges 2 × 10⁻⁶–40 × 10⁻⁶ for NAC and 5 × 10⁻⁷–18 × 10⁻⁶ M for GL and the detection limits are 5.4 × 10⁻⁷ and 4.6 × 10⁻⁷ M, respectively.