TiO2 sol-gel derived amperometric biosensor for H2O2 on the electropolymerized phenazine methosulfate modified electrode

A novel hydrogen peroxide biosensor was developed based on the immobilization of horseradish peroxidase (HRP) in a TiO(2) sol-gel matrix on an electropolymerized phenazine methosulfate (PMS) modified electrode surface. Such membranes are of interest due to their high surface area, biological compatibility, and ease of fabrication. HRP entrapped in the TiO(2) matix was stable and retained its activity to a large extent. Cyclic voltammetry and amperometric measurements were employed to demonstrate the feasibility of electron transfer between immobilized HRP and the glassy carbon electrode via electropolymerized PMS. The influence of various experimental parameters such as operating potential, pH, temperature, and stability was investigated for optimum analytical performance. The biosensor provided a wide linear calibration range from 4.0x10(-6) M to 1.0x10(-3) M, with a detection limit of 8.0x10(-7) M at a signal-to-noise ratio of 3. The sensor retained 80% of its original activity after two months of operation.     

A novel biosensor for specific determination of hydrogen peroxide: catalase enzyme electrode based on dissolved oxygen probe

A biosensor for the specific determination of hydrogen peroxide was developed using catalase (EC 1.11.1.6) in combination with a dissolved oxygen probe. Catalase was immobilized with gelatin by means of glutaraldehyde and fixed on a pretreated teflon membrane served as enzyme electrode. The electrode response was maximum when 50 mM phosphate buffer was used at pH 7.0 and at 35 degrees C. The biosensor response depends linearly on hydrogen peroxide concentration between 1.0x10(-5) and 3.0x10(-3) M with a response time of 30 s. The sensor is stable for >3 months so in this period >400 assays can be performed.     

Fabrication of herbicide biosensors based on the inhibition of enzyme activity that catalyzes the scavenging of hydrogen peroxide in a thylakoid membrane.

A novel herbicide biosensor with a thylakoid modified membrane electrode is presented. Thylakoid, isolated from spinach leaves, was entrapped in a membrane of poly (vinylalcohol) with the styrylpyridinium group (PVA-SbQ). The thylakoid membrane was fixed on the surface of a platinum electrode. It was found that the enzymes in thylakoid kept their activity for several months in the membrane. The oxidative current of hydrogen peroxide in a Tris-HCl buffer solution (pH 7.4) was detected at the modified electrode by a differential pulse voltammetric method. In the presence of herbicides, the oxidation current from the hydrogen peroxide decreased due to an inhibitor effect on the enzymes in thylakoid compared with that in the absence of the herbicides. The changes in the oxidation current at the electrode were proportional to the herbicide concentrations. The sensor could be used to detect herbicides in concentration ranges of 3 x 10(-9) - 1.5 x 10(-7) M for paraquat, 1 x 10(-8) - 3 x 10(-7) M for diuron, 4 x 10(-8) - 3 x 10(-6) M for prometryn, 5 x 10(-8) - 5 x 10(-6) M for atrazine and 1 x 10(-7) - 5 x 10(-6) M for ametryn, respectively. The enzyme activity on scavenging hydrogen peroxide in the modified PVA-SbQ membrane was examined.     

Facile and controllable preparation of glucose biosensor based on Prussian blue nanoparticles hybrid composites

A glucose biosensor based on polyvinylpyrrolidone (PVP) protected Prussian blue nanoparticles (PBNPs)-polyaniline/multi-walled carbon nanotubes hybrid composites was fabricated by electrochemical method. A novel route for PBNPs preparation was applied in the fabrication with the help of PVP, and from scanning electron microscope images, Prussian blue particles on the electrode were found nanoscaled. The biosensor exhibits fast current response (<6 s) and a linearity in the range from 6.7x10(-6) to 1.9x10(-3) M with a high sensitivity of 6.28 microA mM(-1) and a detection limit of 6x10(-7) M (S/N=3) for the detection of glucose. The apparent activation energy of enzyme-catalyzed reaction and the apparent Michaelis-Menten constant are 23.9 kJ mol(-1) and 1.9 mM respectively, which suggests a high affinity of the enzyme-substrate. This easy and controllable construction method of glucose biosensor combines the characteristics of the components of the hybrid composites, which favors the fast and sensitive detection of glucose with improved analytical capabilities. In addition, the biosensor was examined in human serum samples for glucose determination with a recovery between 95.0 and 104.5%.     

Biosensor based on paraffin/graphite modified with sweet potato tissue for the determination of hydroquinone in cosmetic cream in organic phase

An organic-phase biosensor based on paraffin/graphite modified with sweet potato (Ipomoea batatas (L.) Lam.) tissue as the source of peroxidase was developed and used for determining hydroquinone in cosmetic creams. This enzyme in the presence of hydrogen peroxide catalyses the oxidation of hydroquinone to p-quinone which electrochemical reduction back to hydroquinone was obtained at a peak potential of -0.22 V. The recovery of hydroquinone from two samples ranged from 99.1 to 104.1% and a rectilinear analytical curve for hydroquinone concentration from 7.5x10(-5) to 1.6x10(-3) M (r=0.9991) were obtained. The detection limit was 8.1x10(-6) M and relative standard deviation was <1.0% for a solution containing 7.3x10(-4) M hydroquinone and 1.0x10(-3) M hydrogen peroxide in 0.10 M tetrabutylammonium bromide methanol-phosphate buffer solution (95:5% v/v) (n=10). The results obtained for hydroquinone in cosmetic creams using the proposed biosensor are in close agreement with those obtained using a Pharmacopoeia procedure at the 95% confidence level.     

A simple method to fabricate a chitosan-gold nanoparticles film and its application in glucose biosensor

A novel film of chitosan-gold nanoparticles is fabricated by a direct and facile electrochemical deposition method and its application in glucose biosensor is investigated. HAuCl(4) solution is mixed with chitosan and electrochemically reduced to gold nanoparticles, which can be stabilized by chitosan and electrodeposited onto glassy carbon electrode surfaces along with the electrodeposition of chitosan. Then a model enzyme, glucose oxidase (GOD) is immobilized onto the resulting film to construct a glucose biosensor through self-assembly. The resulting modified electrode surfaces are characterized with both AFM and cyclic voltammetry. Effects of chitosan and HAuCl(4) concentration in the mixture together with the deposition time and the applied voltage on the amperometric response of the biosensor are also investigated. The linear range of the glucose biosensor is from 5.0 x 10(-5) approximately 1.30 x 10(-3) M with a Michaelis-Menten constant of 3.5 mM and a detection limit of about 13 microM.     

Electrochemical detection of DNA hybridization by using a zirconia modified renewable carbon paste electrode

A simple, polishable and renewable DNA biosensor was fabricated based on a zirconia modified carbon paste electrode. Zirconia was mixed with graphite powder and paraffin wax to produce the paste for the electrode, and response-optimized at 56% graphite powder, 19% ZrO(2) and 25% paraffin wax. An oligonucleotide probe with a terminal 5'-phosphate group was attached to the surface of the electrode via the strong affinity of zirconia for phosphate groups. DNA immobilization and hybridization were characterized by cyclic voltammetry and differential pulse voltammetry, using methylene blue as indicator. Examination of changes in response with complementary or non-complementary DNA sequences showed that the developed biosensor had a high selectivity and sensitivity towards hybridization detection (< or =2x10(-10) M complementary DNA detectable). The surface of the biosensor can be renewed quickly and reproducibly (signal RSD+/-4.6% for five successive renewals) by a simple polishing step.     

Determination of salicylate in blood serum using an amperometric biosensor based on salicylate hydroxylase immobilized in a polypyrrole-glutaraldehyde matrix

The use of an amperometric biosensor for the salicylate determination in blood serum is described. The biosensor is based on salicylate hydroxylase (EC 1.14.13.1) electropolymerized onto a glassy carbon-working electrode with polypyrrole and glutaraldehyde, to improve the biosensor lifetime. The hexacyanoferrate (II) was also incorporated to work as a redox mediator to minimize possible interferences. The salicylate is enzymatically converted to catechol, which is monitored amperometrically by its electrooxidation at+0.170 V versus SCE (saturated calomel electrode). Salicylate determination was carried out maintaining the ratio between beta-NADH and salicylate at 4:1 (30 degrees C). The amperometric response of the biosensor was linearly proportional to the salicylate concentration between 2.3x10(-6) and 1.4x10(-5) mol l(-1), in 0.1 mol l(-1) phosphate buffer (pH 7.8), containing 0.1 mol l(-1) KCl and 5.0x10(-4) mol l(-1) Na(2)H(2)EDTA, as supporting electrolyte. The recovery studies, in the presence of several interfering compounds, showed recoveries between 96.4 and 104.8%. The useful lifetime of the biosensor in the concentration range evaluated was at least 40 days, in continuous use. Blood serum samples analyzed by this biosensor showed a good correlation compared to the spectrophotometric method (Trinder) used as reference, presenting relative deviations lower than 7.0%.     

Studies of the interaction between Aloe-emodin and DNA and preparation of DNA biosensor for detection of PML-RARalpha fusion gene in acute promyelocytic leukemia

The interaction of Aloe-emodin (AE) with salmon sperm DNA in 0.1M Tris-HCl buffer (pH 4.4) and at the DNA-modified glassy carbon electrode (GCE) was systemically studied with voltammetry and ultraviolet-visible (UV-vis) spectroscopy. AE had excellent electrochemical activity on the GCE with a couple of redox peaks. We propose that AE can intercalate into DNA strands forming a nonelectroactive complex, which results in the decrease of the reduction peak current of AE. The Langmuir adsorption constants of AE at ss- and dsDNA/GCE were (2.1+/-0.4)x10(5) and (2.7+/-0.2)x10(5)M(-1), respectively. The difference between AE at ss- and dsDNA has been used for the preparation of a sequence-specific DNA electrochemical biosensor for detection of PML-RARalpha fusion gene in acute promyelocytic leukemia (APL) with a detection limit of 6.7x10(-8)M and a linear range from 1.5x10(-8) to 1.5x10(-7)M. The selectivity of ssDNA-modified electrode was also described.     

Enzyme-functionalized gold nanowires for the fabrication of biosensors

Gold nanowires were prepared by an electrodeposition strategy using nanopore polycarbonate (PC) membrane, with the average diameter of the nanowires about 250 nm and length about 10 microm. The nanowires prepared were dispersed into chitosan (CHIT) solution and stably immobilized onto glassy carbon electrode (GCE) surface. The electrochemical behavior of gold nanowire modified electrode and its application to the electrocatalytic reduction of hydrogen peroxide (H(2)O(2)) were investigated. The modified electrode allows low potential detection of hydrogen peroxide with high sensitivity and fast response time. Moreover, the good biocompatibility of nanometer-sized gold, the vast surface area of the nanowire-structure make it ideal for adsorption of enzymes for the fabrication of biosensors. Glucose oxidase was adsorbed onto the nanowire surface to fabricate glucose biosensor as an application example. The detection of glucose was performed in phosphate buffer (pH 6.98) at -0.2 V. The resulting glucose biosensor exhibited sensitive response, with a short response time (<8 s), a linear range of 10(-5)-2 x 10(-2) M and detection limit of 5 x 10(-6) M.     

Covalent attachment of glucose oxidase to an Au electrode modified with gold nanoparticles for use as glucose biosensor

A feasible method to fabricate glucose biosensor was developed by covalent attachment of glucose oxidase (GOx) to a gold nanoparticle monolayer modified Au electrode. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) of ferrocyanide followed and confirmed the assemble process of biosensor, and indicated that the gold nanoparticles in the biosensing interface efficiently improved the electron transfer between analyte and electrode surface. CV performed in the presence of excess glucose and artificial redox mediator, ferrocenemethanol, allowed to quantify the surface concentration of electrically wired enzyme (Gamma(E)(0)) on the basis of kinetic models reported in literature. The Gamma(E)(0) on proposed electrode was high to 4.1 x 10(-12) mol.cm(-2), which was more than four times of that on electrode direct immobilization of enzyme by cystamine without intermediate layer of gold nanoparticles and 2.4 times of a saturated monolayer of GOx on electrode surface. The analytical performance of this biosensor was investigated by amperometry. The sensor provided a linear response to glucose over the concentration range of 2.0 x 10(-5)-5.7 x 10(-3) M with a sensitivity of 8.8 microA.mM(-1).cm(-2) and a detection limit of 8.2 microM. The apparent Michaelis-Menten constant (K(m)(app)) for the sensor was found to be 4.3 mM. In addition, the sensor has good reproducibility, and can remain stable over 30 days.     

An amperometric horseradish peroxidase inhibition biosensor for the determination of phenylhydrazine

An amperometric horseradish peroxidase (HRP) inhibition biosensor has been substantially constructed by the help of N,N-dicyclohexylcarbodiimide (DCC), N-hydroxysuccinimide (NHS). The preparation steps and the biosensor response to phenylhydrazine were monitored by electrochemical impedance spectroscopy (EIS), cyclic voltammetry, and chronoamperometry. The proposed biosensor could be applied to determine phenylhydrazine in a 0.10 M phosphate buffer solution containing 1.2 mM hydroquinone and 0.50 mM H(2)O(2) by phenylhydrazine, inhibiting the catalytic activity of the HRP enzyme in the reduction of H(2)O(2). The system was optimized to realize a reliable determination of phenylhydrazine in the range of 2.5 x 10(-7) to 1.1 x 10(-6) M with a detection limit of 8.2 x 10(-8) M and a correlation coefficient of 0.999. The modified electrode displayed good reproducibility, sensitivity and stability for the determination of phenylhydrazine.     

Screen-printed electrode based on AChE for the detection of pesticides in presence of organic solvents

A screen-printed biosensor for the detection of pesticides in water miscible organic solvents is described based on the use of p-aminophenyl acetate as acetylcholinesterase substrate. The oxidation of p-aminophenol, product of the enzymatic reaction was monitored at 100 mV vs. Ag/AgCl screen-printed reference electrode. Miscible organic solvents as ethanol and acetonitrile were tested. The acetylcholinesterase (AChE) was immobilised on a screen-printed electrode surface by entrapment in a PVA-SbQ polymer and the catalytic activity of immobilised AChE was studied in the presence of different percentages of organic solvents in buffer solution. The sensor shows good characteristics when experiments were performed in concentrations of organic solvents below 10%. No significant differences were observed when working with 1 and 5% acetonitrile in the reaction media. Detection limits as low as 1.91x10(-8) M paraoxon and 1.24x10(-9) M chlorpyrifos ethyl oxon were obtained when experiments are carried out in 5% acetonitrile.     

Electrochemical characterization of biosensor based on nitrite reductase and methyl viologen co-immobilized glassy carbon electrode

Nitrite reductase (NiR, nitric-oxide: ferricytochrome c oxidoreductase, EC 1.7.2.1) and methyl viologen (MV) were co-immobilized on glassy carbon electrode (GCE, d=3 mm) by polymer entrapment, and the electrode was tested as an electrochemical biosensor for amperometric determination of nitrite. The immobilization was performed by sequential loading and drying of a homogeneous mixture of poly(vinyl alcohol) (PVA), NiR and MV, followed by poly(allylamine hydrochloride) (PAH) solution, and finally hydrophilic polyurethane (HPU) dissolved in chloroform. The positively charged PAH layer could effectively keep immobilized cationic MV from diffusing through the membrane, holding mediator tightly near or on the electrode surface. The working principle of the biosensor was based on MV mediated electron transfer between electrode and immobilized NiR. The response time (t(90%)) of the biosensor was about 20 s and sensitivity was 11.8 nA/ microM (2.5 mU NiR) with linear response range of 1.5-260 microM (r(2)=0.996) and detection limit of 1.5 microM (S/N=3). Lineweaver-Burk plot showed that Michaelis-Menten constant (K(m,app)) was about 770 microM. The biosensor showed durable storage stability for 24 days (stored in ambient air at room temperature) retaining 80% of its initial activity, and showed satisfactory reproducibility (relative standard deviation (R.S.D.)=3.8%, n=9). Interference study showed that chlorate, chloride, sulfite, sulfate did not interfere with the nitrite determination, however, nitrate interfered with the determination with relative sensitivity of 38% (ratio of sensitivity for nitrate to that for nitrite). In addition to the full characterization of the biosensor, kinetic study was also conducted in solution and the homogeneous rate constant (k(2)) between NiR and MV were determined by chronoamperometry to be 5.8 x 10(5) M(-1) s(-1).     

Amperometric hydrogen peroxide biosensor based on horseradish peroxidase-labeled nano-Au colloids immobilized on poly(2,6-pyridinedicarboxylic acid) layer by cysteamine.

A sensitive hydrogen peroxidase (H2O2) amperometric sensor based on horseradish peroxidase (HRP)-labeled nano-Au colloids has been proposed. Nano-Au colloids were immobilized by the thiol group of cysteamine, which was associated with the carboxyl groups of poly(2,6-pyridinedicarboxylic acid) (PPDA). With the aid of the hydroquinone, the sensor displayed excellent electrocatalytical response to the reduction of H2O2. Compared with the non-Au-colloid modified electrode, i.e., PPDA/HRP, the Au-colloid modified electrode exhibited better performance characteristics, including stability, reproducibility, sensitivity and accuracy. The biosensor shows a linear response to H2O2 in the range of 3.0 x 10(-7) - 2 x 10(-3) M. The detection limit was 1.0 x 10(-7) M.     

Amperometric biosensor for hydrogen peroxide based on direct electrocatalysis by hemoglobin immobilized on gold nanoparticles/1,6-diaminohexane modified glassy carbon electrode.

A facile strategy of an amperometric biosensor for hydrogen peroxide based on the direct electrocatalysis of hemoglobin (Hb) immobilized on gold nanoparticles (GNPs)/1,6-diaminohexane (DAH) modified glassy carbon electrode (GCE) has been described. A uniform monolayer film of DAH was initially covalently bound on a GCE surface by virtue of the electrooxidation of one amino group of DAH, and another amino group was modified with GNPs and Hb, successively. The fabrication process was characterized by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM). The proposed biosensor exhibited an effective and fast catalytic response to the reduction of H2O2 with good reproducibility and stability. A linear relationship existed between the catalytic current and the H2O2 concentration in the range of 1.5x10(-6) to 2.1x10(-3) M with a correlation coefficient of 0.998 (n=24). The detection limit (S/N=3) was 8.8x10(-7) M.     

A new enzyme electrode based on ascorbate oxidase immobilized in gelatin for specific determination of l-ascorbic acid

A biosensor for the specific determination of l-ascorbic acid in fruit juices and vitamin C tablets was developed using ascorbate oxidase (EC 1.10.3.3) from cucumber (Cucumis sativus L.) in combination with a dissolved oxygen probe. Ascorbate oxidase immobilized with gelatin using glutaraldehyde and fixed on pretreated teflon membrane served as an enzyme electrode. The phosphate buffer (50 mM, pH 7.5) and 35 degrees C were established as providing the optimum conditions. The biosensor response depends linearly on l-ascorbic acid concentration between 5.0x10(-5) and 1.2x10(-3) M with a response time 45 s. The biosensor is stable for more than 2 months, while more than 200 assays were performed. The results obtained for fruit juices and tablets were compared with DCIP (2,6 dichlorophenolindophenol) method.     

Determination of nitrite based on mediated oxidation at a carbon paste electrode modified with a ruthenium polymer

The use of carbon paste electrodes modified with [Ru(bpy)(2)(PVP)(10)Cl]Cl for the mediated detection of nitrite is described. This surface modifier substantially lowers the overpotential for nitrite oxidation, hence permitting its determination at a lower potential. Various electrode characteristics were optimized, including the modifier loading and the monitoring potential, using batch amperometry. Standard calibration curves yielded slopes of 0.30 microA/microM over the linear range 5 x 10(-8)-5 x 10(-4)M nitrite with a detection limit of 3 x 10(-8)M (1.38 ppb) nitrite. The modified electrode response was shown to be relatively stable over a period of 5 days with a signal diminution of 8%. Electrode-to-electrode precision was measured as 11.4%. Flow-injection studies indicated the suitability of this electrode as a detector in flowing streams.     

Construction of a l-lysine biosensor by immobilizing lysine oxidase on a gold-poly(o-phenylenediamine) electrode

The construction of a l-lysine biosensor on a Si-gold strip electrode (SGSE) is described in this study. The construction comprises (a) the formation of poly(o-phenylenediamine, o-PD) membrane on the electrode surface via electropolymerization and (b) the immobilization of lysine oxidase on the gold/poly(o-PD) electrode with glutaraldehyde. The behavior of the gold/poly(o-PD) electrode against H(2)O(2) and lysine, as well as the repeatability of the electropolymerization and the time stability of the polymer were studied. The study showed that the electropolymerization procedure is repeatable, and that the polymer is quite stable for at least 40 days. The biosensor showed a linear calibration curve in the range 0.01-1x10(-5) M (0.1-10 muM) lysine. The interfering effect of other amino acids on the biosensor performance was also studied and amperometric selectivity coefficients were calculated. The biosensor responded mainly against tyrosine and cysteine, while the response to phenylalanine, arginine, histidine and ornithine was very low. By changing the electropolymerization conditions, the effect of interferents was further reduced.     

An amperometric biosensor based on the coimmobilization of horseradish peroxidase and methylene blue on a beta-type zeolite modified electrode

A new biosensor for the amperometric detection of hydrogen peroxide was developed based on the coimmobilization of horseradish peroxidase (HRP) and methylene blue on a beta-type zeolite modified glassy carbon electrode without the commonly used bovine serum albumin-glutaraldehyde. The intermolecular interaction between enzyme and zeolite matrix was investigated using FT-IR. The cyclic voltammetry and amperometric measurement demonstrated that methylene blue co-immobilized with HRP in this way displayed good stability and could efficiently transfer electrons between immobilized HRP and the electrode. The sensor responded rapidly to H2O2 in the linear range from 2.5 x 10(-6) to 4.0 x 10(-3) M with a detection limit of 0.3 microM. The sensor was stable in continuous operation.