Effect of ausforming temperature and strain on the bainitic transformation kinetics of a low carbon boron steel

The effect of ausforming temperature and strain on the bainitic transformation kinetics was investigated in a low carbon boron steel. A new mechanism, which is based on the competition between the increase in nucleation rate and the decrease in average volume of bainite sheaf after deformation, is proposed. The increase in nucleation rate is due to the decrease in boron concentration at the grain boundaries after small deformation and the formation of sub-grain boundaries at the grain interior after large deformation. The decrease in average volume of bainite sheaf is ascribed to the frequent impingement of bainite sub-units after deformation. The increase in nucleation rate after deformation results in the decrease in incubation time, which is confirmed from the experiment. The increase in nucleation rate overcomes the decrease in average volume of bainite sheaf, resulting in the increase in transformation velocity and volume fraction after small deformation. On the contrary, the decrease in the average volume of bainite sheaf overcomes the increase in nucleation rate after large deformation, leading to the decrease in transformation velocity and volume fraction of bainite.     

Thermodynamically equilibrium roton states of nanoparticles in molten and vapour phases

We show a possibility for a thermodynamically equilibrium nanocrystalline structure consisting of nanosized solid inclusions to appear in a melt just beyond the melting curve. Thermodynamic stability of the nanocrystalline structure in the melt results from the free energy lowering due to rotational motion of nanoparticles. The main contribution to the reduction of the free energy of the system is due to an increase in the rotational entropy and change in formation energy of nanocrystals, i.e. the nanocrystalline structure in the melt, like vacancies in a crystal, is an equilibrium defect structure of the melt. It is demonstrated that similar nanocrystalline structures can also appear in the vapour phase in the form of liquid nanodrops and in liquid solutions, e.g. in He II.     

XPS and SIMS investigation on the role of nitrogen in Si nanocrystals formation

Since the demonstration of optical gain in silicon nanocrystals, in the last few years several papers appeared in the literature reporting gain measurements in silicon nanocrystals embedded in a silica matrix produced by different techniques. However, it is still unclear which are the structural, physical and chemical factors that contribute to enhance photoluminescence and gain in this type of samples. In particular, the presence and the role of nitrogen in the SiO₂ matrix are in fact supposed to be essential factors in understanding the gain mechanism.In fact it is possible to obtain similar samples with very different nitrogen content in the silica matrix changing one of the precursor gases used in the deposition process, thus evidencing the structural and chemical differences introduced by the presence of nitrogen. In this paper SIMS and XPS analysis of two series of similar samples, but with a very different nitrogen content, will be presented and compared. The data collected at different annealing temperatures, together with ellipsometric measurements, give important information on the role played by the nitrogen present in the matrix in the process of silicon nanocrystal formation. Moreover, we demonstrate that the annealing process causes always some oxidation of the sample surface and that nitrogen is incorporated in the material from the annealing atmosphere in nitrogen free samples.     

Changes in ADC caused by tensile loading of rabbit achilles tendon: evidence for water transport

Water diffusion measurements were performed on rabbit Achilles tendons during static tensile loading and tendons in an unloaded state. The apparent diffusion coefficient (ADC) was measured along two directions: parallel and perpendicular to the long axis of the tendon. Tendons were studied after being prepared in two ways: (a) after being stored frozen in phosphate-buffered saline (PBS) and (b) freshly isolated. Statistically significant directional anisotropy was observed in the ADC in all tendons. The ADC was significantly greater in the direction parallel to the long axis of the tendon than in the perpendicular direction. The anisotropy is attributed to the greater restrictions seen by the water molecules in the perpendicular direction and is consistent with the known geometry of the tendon. Storage in PBS caused tendons to swell. This increased the ADC measured along both directions and reduced the anisotropy. The existence of anisotropy in the ADC was not related to the orientation of the specimen in the magnet. The ADC increased along both directions following the application of a 5-N tensile load; the increase was greatest along the perpendicular axis of the tendon. In order to determine whether load-related changes in the ADC reflected changes in interfibrilar spacing, we used electron microscopy to measure load-related changes in fibril spacing. Load-related changes in fiber spacing could not account for the observed changes in the ADC. The increase in ADC caused by loading was attributed to the extrusion of tendon water into a bulk phase along the outside surface of the tendon. In PBS-stored samples, enough fluid was extruded that it could be visualized. The transient response of the ADC to a 5-N tensile load was also studied. The absolute ADC in both directions increased with loading and recovered to baseline upon unloading. The transient changes in ADC, for both loading and unloading, had a mean time constant of approximately 15 min. The magnitude of the load-induced transient ADC changes was comparable to that seen in the static-loading experiments.     

铅基反应堆燃料组件间隙横流周期性研究

燃料组件内冷却剂的横流对反应堆堆芯的换热有很大影响,为研究铅基反应堆燃料组件内冷却剂的横向速度分布,对CiADS反应堆燃料组件组件局部的7,19棒束的单螺距及多螺距多种几何进行建模和CFD（Computational Fluid Dynamics）模拟,并对其间隙内横向速度进行分析。研究表明: 19棒束组件内通道、角通道的相邻间隙内横向速度的分布在组件轴向和横向上有明显周期性,横向上根据两个内通道间隙平移旋转的位置关系由一个间隙的结果经过平移一定相位角度可以得到另一个间隙分布结果,沿轴向多螺距模型每个螺距长度内横向速度分布一致。7棒束组件在相同类型通道内横向速度分布大小及趋势与19棒束一致。少棒束单螺距组件结果进行横向及轴向的周期性延拓可以得到多棒束多螺距模型间隙内的横流分布。Cross flow of a coolant in fuel assembly had a great impact on the heat transfer of a reactor core. In order to study the characteristics of the cross flow in lead-based fast reactor assemblies, the CiADS fuel assemblies were used as research object. Fine geometric models and CFD simulation of 7 and 19 pin bundle and multi-pitch length assemblies based on CiADS fuel assemblies were carried out. The distribution of the cross flow velocity in several geometric models was compared and analyzed. The results show that the distribution of the cross flow velocity in gaps of interior and corner channel in 19 pin bundle has obvious periodicity in both axial and horizontal direction. In the horizontal direction, the results of one gap can be translated by a certain phase angle to obtain another gap distribution result according to the positional relationship of the translational rotations of the two internal channel gaps. The distribution of cross flow velocity is uniform in each pitch length of multi-pitch model in the axial direction. And the distribution of transverse flow in gaps of 7 pin bundle is similar to the distribution in the same kind of gaps in 19 pin bundle. The results of fewer pin bundle with single pitch length can be periodically extended in axial and transverse direction to obtain the characteristics of cross flow in geometric models with multi-pitch length and more rods.     

Ni,Ti, and NiTi laser ablation in vacuum and in water to deposit thin films or to generate nanoparticles in solution

An ns Nd:YAG pulsed laser was used to deposit thin films in a vacuum and to generate nanoparticles in the water of Ni, Ti, and NiTi alloys. Laser ablation was measured in terms of removing mass per laser pulse. The laser-generated plasma in vacuum was characterized in terms of temperature and energy of emitted particles. The ablation in water produces nanoparticles with dimensions of the order of 25 nm and solutions with concentrations of the order of some mg/ml. The NiTi alloy stoichiometry is well reported in the deposited thin film and in the composition of the produced nanoparticles.     

Dynamic feature analysis in bidirectional pedestrian flows

Analysis of dynamic features of pedestrian flows is one of the most exciting topics in pedestrian dynamics. This paper focuses on the effect of homogeneity and heterogeneity in three parameters of the social force model, namely desired velocity, reaction time, and body size, on the moving dynamics of bidirectional pedestrian flows in the corridors. The speed and its deviation in free flows are investigated. Simulation results show that the homogeneous higher desired speed which is less than a critical threshold, shorter reaction time or smaller body size results in higher speed of flows. The free dynamics is more sensitive to the heterogeneity in desired speed than that in reaction time or in body size. In particular, an inner lane formation is observed in normal lanes. Furthermore, the breakdown probability and the start time of breakdown are focused on. This study reveals that the sizes of homogeneous desired speed, reaction time or body size play more important roles in affecting the breakdown than the heterogeneities in these three parameters do.     

微波消解-ICP-AES测定鄱阳湖流域沉积物中微量元素

为了研究鄱阳湖沉积物中微量元素近几年来随季节、年度及沿程的变化情况,对2003年和2005年不同季节采集的鄱阳湖流域各采样点底泥进行了ICP-AES测定.结果表明,鄱阳湖沉积物中各元素的含量随着季节和年度变化而发生一定改变,枯水期普遍大于丰水期;南矶山2005年Cu和Pb含量较2003年有所降低;蔡家湾则与南矶山相反;姚公渡2005年Cu含量也较2003年低,Pb含量则高于2003年;与鄱阳湖流域底泥背景值相比,所测几个样点的Cu,Pb,Cr和Zn含量均在一定程度上超标;除大坞河外,其余各样点As含量均在背景值范围内;从饶河到鄱阳湖入湖口处,各元素含量呈逐渐降低趋势.文章提出的研究方法操作简便,效率高,劳动强度低.     

在NaCl和HTAB共存条件下甲基纤维素溶液凝胶化行为

利用流变仪研究了甲基纤维素(MC)溶液在NaCl、十六烷基三甲基溴化铵(HTAB)以及两者共存下MC溶液的凝胶化行为,发现其凝胶化温度随着NaCl浓度的增加而下降,随着HTAB浓度的增加而上升;但是MC/NaCl的凝胶化温度保持不变,与HTAB浓度 无关,而MC/HTAB溶液的凝胶化温度则随着NaCl浓度的增加而下降．以上的实验结果表明,在NaCl存在下,HTAB将被诱导形成胶束,因此MC/NaCl的凝胶化温度保持不变;反之,当NaCl不存在时,HTAB将优先吸附到MC上而不会在溶液中形成胶束,尽管其浓度     

水溶液中微量Cu元素的激光诱导光谱检测

采用普通打印纸作为基底置于含有痕量重金属离子的水溶液中,用于富集溶液中的重金属Cu元素,烘干后用激光诱导击穿光谱进行定量分析。该方法克服了用激光诱导击穿光谱方法直接分析液相样品中重金属含量时存在水的溅射和灵敏度低等不足。实验中选用324.7 nm的光谱线作为分析线,研究了光谱强度与富集时间的关系,建立了用于溶液中Cu元素定量测量的校正曲线,检测限达到0.023 mg·L-1。为水体中重金属检测提供了一个可行的具有良好灵敏度分析技术。     

CPL技术在空间飞行器上的应用

本文对ＣＰＬ技术进行了简要概述,介绍了其工作原理与工作特性,并讨论了ＣＰＬ技术在空间飞行器上的可能应用方式。其中,对ＣＰＬ技术应用于空间设备的散热进行了全面阐述,并给予理论分析;此外,对ＣＰＬ技术应用于空间设备的主动热控制,也作了简要介绍;对ＣＰＬ技术未来有发展前景的应用方式进行了展望。     

石墨狭缝中甲烷吸附的分子动力学模拟

用分子动力学模拟研究石墨狭缝中甲烷的吸附,考察狭缝宽度和温度对甲烷吸附的影响.模拟发现甲烷在石墨狭缝中出现分层现象,吸附层中甲烷具有类液特征,第一吸附层内甲烷中总有两个氢原子的连线与另外两个氢原子的连线分别位于平行于狭缝壁的两个平面内,游离层中甲烷呈现气体的特征;碳原子间的平均作用势说明吸附层中甲烷分子间结合能力大于游离层,吸附态是甲烷在石墨狭缝中的主要赋存形式之一;伦敦力以及由吸附层净电荷产生的电场力是甲烷吸附和分层的主要原因;甲烷的吸附量随狭缝宽度增大或温度升高而减少,当狭缝宽度小于16.46Å时,甲烷仅以吸附形态存在.甲烷在第一吸附层中的扩散能力最弱、游离层中最强,甲烷扩散系数随狭缝宽度的增大或温度的升高而增大.     

夏秋两季洱海、太湖表层混合层的深度变化特征及其机理分析

湖泊表层混合层深度的变化不仅影响湖泊水生生态系统的演变, 而且影响流域的局地气候、降水量的时空格局等. 基于2008年夏秋两季洱海(高原湖泊)和太湖(平原湖泊)的气象与水温廓线观测资料, 分析探讨了两湖表层混合层深度的变化特征及其机制. 结果表明: 夏季洱海能维持持续的分层现象, 秋季有明显的日分层现象, 而在相应的两季中, 太湖仅可能存在日分层现象; 洱海表层混合层深度较同期太湖更浅; 太湖两季的表层混合层深度变化较洱海频繁, 即太湖水体混合与分层的交替过程对气象条件的响应较洱海更为迅速. 太湖这类浅水湖泊, 水深是抑制其存在稳定、持续分层的关键因素, 在合适的辐射条件下, 可形成日分层现象; 而洱海这类深度的湖泊, 净热量通量是影响其是否存在持续、稳定分层的主要因子. 该研究为进一步探讨湖泊与大气两种湍流运动的耦合机制及水生生态环境演替规律等提供了有力的参考.     

降雨对无线激光通信的影响

通过激光信号在雨介质中传输的实验发现,在大雨环境下,激光信号透射率要比在小雨或微雨的情况下大。这说明光信号在小雨时衰减较大,在大雨时衰减较小。这一现象与人们通常所认为的有所不同。针对降雨对激光信号的影响,根据Mie散射理论和Weibull雨滴尺寸分布模型,分析了不同尺寸的粒子对光的散射作用以及对衰减效率因子的影响,推导出单球粒子对光波的衰减公式,得到了衰减与降雨率的确定关系。通过数值计算发现,与小粒子相比大粒子的前向散射光强更大且更加集中;激光信号在雨介质中传输时,衰减系数在小雨时较大,中雨、大雨时较小,暴雨时不断增大。这一结果与实际情况较吻合,为激光在通信系统中的应用提供了一定的理论依据。     

Caffeine as non-toxic corrosion inhibitor for copper in aqueous solutions of potassium nitrate

Different electrochemical methods were employed in order to confirm the ability of caffeine (1,3,7-trimethylxanthine) to inhibit the corrosion processes of copper in aqueous potassium nitrate solutions in the absence and in the presence of chloride. Some experiments were repeated in potassium perchlorate in order to compare the influence of the medium. The interaction between the organic compound and the electrode surface occurs independently of the electrode potential. However, maximum interaction was observed at 0.0 V (Ag/AgCl) in aerated solutions, and at −0.25 V (Ag/AgCl) in deaerated solutions.The presence of the organic compound adsorbed on the electrode surface was confirmed by comparing the voltammograms of copper electrode in the absence and presence of 1.5 mmol L⁻¹ of dissolved caffeine. The same results were observed by comparing polarization curves in the absence and in the presence of caffeine.Anodic currents decrease noticeably in the presence of the organic compound. Chronoamperometric experiments were conclusive to prove the inhibitor capability of caffeine to decrease the corrosion dissolution processes of copper under anodic polarization.     

梯度磁场作用下光纤中磁流体光透射特性研究的建模与分析

对光纤中磁流体在梯度磁场作用下的光透射特性进行了研究,提出光纤中磁流体的光透射率变化主要来源于梯度磁场引起的磁流体密度分布变化。根据郎之万函数和流体理论,推导了光纤中磁流体在梯度磁场作用下的密度分布,并根据Beer-Lambert定律,得到磁流体光功率透射衰减和纳米粒子局部密度的关系,从而建立光纤中磁流体在梯度磁场作用下光透射特性的理论模型。进而对光纤中磁流体在不同梯度磁场作用下的光透射功率进行数值分析,得到不同磁场强度和磁场梯度下光纤中磁流体透射功率的变化规律。最后将数值分析的结果和实验数据进行对比,验证了模型的合理性, 同时也验证了梯度磁场作用下磁流体光透射功率的变化主要来源于磁流体密度分布变化的推论。     

Electrostatic field and charge distribution in small charged dielectric droplets

The charge distribution in small dielectric droplets is calculated on the basis of continuum medium approximation. There are considered charged liquid spherical droplets of methanol in the range of nanometer sizes. The problem is solved by the following way. We find the free energy of some ion in dielectric droplet, which is a function of distribution of other ions in the droplet. The probability of location of the ion in some element of volume in the droplet is a function of its free energy in this element of volume. The same approach can be applied to other ions in the droplet. The obtained charge distribution differs considerably from the surface distribution. The curve of the charge distribution in the droplet as a function of radius has maximum near the surface. Relative concentration of charges in the vicinity of the center of the droplet does not equal to zero, and it is the higher, the less is the total charge of the droplet. According to the estimates the model is applicable if the droplet radius is larger than 10 nm.     

Cytoskeletal involvement in cotton fiber growth and development

The organization of cellulose microfibrils in plant cell walls influences physical properties of the wall and thus cell expansion characteristics. Developing cotton fiber represents an excellent model system for the analysis of the biological regulation of cell wall patterns. Current research indicates that the cytoskeleton has a major role in directing the deposition and organization of cellulose microfibrils in the cell walls of many plant systems, including developing cotton fibers. Both microtubules and microfilaments appear to be involved in regulating changes observed in microfibril patterns during fiber development. The polylamellate architecture of the fiber wall can be attributed to changes in the orientation of cytoplasmic microtubules which appear to direct the orientation of microfibril deposition in each successive layer of the fiber wall. In the drug-induced absence of microtubules, cellulose is deposited in the fiber wall in a swirled pattern of bundled microfibrils. Interaction between adjacent microfibrils may influence cell wall organization on a localized level. In contrast to the direct involvement of microtubules on wall organization, microfilaments appear to be indirectly involved in the deposition of cellulose microfibrils. Current evidence indicates that microfilaments influence wall organization by controlling changes in microtubules patterns. Although a greater understanding of the relationship between the cytoskeleton and the fiber wall is needed, there is sufficient evidence to indicate that genetic manipulation of cytoskeletal components is one path toward future direct manipulation of cell expansion characteristic in many plant systems and may lead to improvements in the textile qualities of cotton fibers.     

The effect of magnetic field on plasma particles in dusty plasma

In this work, we present the investigation of the formation features and internal structure of dust clouds created in plasma of glow discharge in the external magnetic field corresponding to a range of moderate and strong fields, at which the ion component is magnetized. The analysis of the plasma magnetization in the presence of dust components is carried out. We defined the values of magnetic induction at which the changes in dynamics of plasma particles in magnetic field in light inert gases are expected. The experimental setup was built in two versions. For the purpose of generating of magnetic field, the first setup was equipped with ordinary magnetic coils, and the second one included a superconducting solenoid. The discharge tubes, the main chambers where plasma was ignited and maintained in a glow discharge in lowered pressure, also have certain peculiarities, which we describe below. While using helium as a bulk gas, our study focused only on the dust trap in the region of narrowing discharge current. For neon, we used two traps: the striation trap and one just mentioned above placed in the narrowing of the discharge tube. As a result, the steady dust structures in a glow discharge under the magnetization of ions and electrons were obtained for the first time. Dust structures were rotated and tended to form a dust cluster and shell structure. A number of parameters of magnetization achieved in experiments were calculated.     

忽地笑鳞茎中总生物碱含量的月动态变化

采用紫外分光光度法测定了不同月份忽地笑鳞茎中总生物碱含量,为确定适宜的采收时间提供实验依据。结果表明,忽地笑鳞茎中总生物碱含量随生长发育时期或月份不同存在一定差异,其中11月的最高,12月次之,1月的最低,最高值与最低值相比,约为2.6倍,差异达极显著水平(P<0.01)。精密度、稳定性实验及回收率等方法学考察表明,紫外分光光度法测定忽地笑鳞茎中总生物碱含量效果好,稳定性强,方法可靠。综合忽地笑鳞茎中总生物碱含量、中药材产量和土地利用率等因素考虑,以11月底前后采收比较适宜。