交联聚氨酯水分散体的合成

将硅氧烷封端的含亲水基团的线性聚氨酯预聚体分散于水中 ,获得稳定的聚氨酯分散体 .由于硅氧基团水解、缩合 ,在分散体粒子内产生扩链交联反应 ,生成了交联水基聚氨酯分散体 .透射电子显微镜研究表明分散体粒径小、分布宽 .扫描电子显微镜研究了成膜结构及成膜性能与粒径的关系 .溶胀实验计算获得的两交联点之间的平均分子量与理论平均分子量相符 .研究还发现此分散体膜在干燥过程中可进一步交联 .膜的水溶胀及机械性能表明 ,此分散体具有极大的工业应用价值 .     

环氧硅氧烷对丙烯酸酯类无皂涂料性能的影响

无皂乳液涂料;环氧硅氧烷对丙烯酸酯类无皂涂料性能的影响     

甲基丙烯酸二甲胺乙酯对光固化阴极电泳漆性能的影响

通过自由基共聚合得到丙烯酸树脂,然后用甲基丙烯酸异氰酸乙酯(MOI)对其改性,合成了既带有N,N-二甲胺基,又带有乙烯基的紫外光固化阴极电泳漆基体树脂。研究了甲基丙烯酸二甲胺乙酯(DMAE-MA)用量对改性丙烯酸树脂水分散体和漆膜性能的影响规律。结果表明,树脂分子链上引入DMAEMA后,其水分散性有较大改善,随DMAEMA用量增加,水分散体的粒径减小、粘度略有增加、稳定性增强,电泳沉积量和漆膜厚度增加,电泳沉积漆膜的初期含水率增加。综合考虑水分散体和漆膜的性能,丙烯酸树脂中DMAEMA质量分数以0．144左右为宜。     

高含氢聚甲基硅氧烷改性聚丙烯酸酯乳液的结构与涂层性能

高含氢聚甲基硅氧烷改性聚丙烯酸酯乳液的结构与涂层性能;高含氢聚甲基硅氧烷; 改性聚丙烯酸酯乳液; 核壳型共聚乳胶; 涂层剂     

新型环氧丙烯酸树脂增韧剂的合成

用马来酸酐和聚乙二醇1000合成具有反应活性端基的聚乙二醇,用红外与核磁共振进行了表征,并用其对环氧丙烯酸树脂进行改性;研究反应温度、反应时间对反应及产物性能的影响;用红外对反应性聚乙二醇和环氧丙烯酸树脂的固化物进行分析.结果表明,反应性聚乙二醇参与了环氧丙烯酸树脂的固化反应,可在交联网络中构成不同长度的柔性链段,显著地提高了环氧丙烯酸树脂的冲击强度.     

硅氧烷表面改性聚醚酯聚酰亚胺的研究

通过两种方法。即将γ-氨丙基封端的聚二甲基硅氧烷和对氨基苯甲酸酯封端的聚(四亚甲基)醚与均苯四甲酸二酐共缩聚,和将两种预制的聚酰胺酸溶液共混,合成了一组硅氧烷改性的聚醚酯聚酰亚胺材料。ESCA能谱和表面水接触角测量研究材料的表面性质发现,硅氧烷在材料表面富集,对聚醚酯聚酰亚胺材料具有显著的表面改性作用,硅氧烷改性的聚醚酯聚酰亚胺,其热稳定性能和气体透过性能有一定程度的提高,但抗张强度和介电性能有所降低。     

聚苯基硅氧烷与聚甲基苯基硅氧烷改性环氧树脂的合成与性能比较

热熔法制备了一系列聚苯基甲氧基硅氧烷(PPMS)、聚甲基苯基甲氧基硅氧烷(PMPS)改性环氧树脂,通过环氧值、红外光谱(IR)分析表明聚硅氧烷接枝了E-20环氧树脂且环氧基保持不变.探讨了有机硅含量对改性树脂固化体系耐热性能及韧性的影响.实验表明,当E-20环氧树脂与PPMS、PMPS的质量比为7∶3时,改性树脂固化体系的耐热性能明显提高,玻璃化转变温度(Tg)为95.8、88.3℃,分别比改性前提高了9.0℃和1.5℃;质量损失50%时的热分解温度(Td)为476.5、487.8℃,分别比改性前提高了58.3℃和69.5℃.与ED-30固化体系相比,EPMS-30固化物的耐热性能,韧性等力学性能提高的更加明显,并且还具有优良的涂膜性能.     

聚氨酯-聚甲基丙烯酸丁酯共聚体水分散体的制备及性能研究

研究了聚氨酯-聚甲基丙烯酸丁酯共聚体水分散体(PUBMA)的制备及其性能.首先采用电子转移再生催化剂原子转移自由基聚合(ARGET ATRP),以α-溴代异丁酸羟丁酯为引发剂,溴化铜(CuBr2)为催化剂,五甲基二乙烯三胺(PMDETA)为配体,辛酸亚锡(Sn(EH)2)为还原剂,制备了端羟基聚甲基丙烯酸丁酯(PBMA-OH).其次以聚醚二元醇(N220)、聚醚三元醇(N330)、PBMA-OH、甲苯-2,4-二异氰酸酯(TDI)、二羟甲基丙酸(DMPA)为原料,制备聚氨酯-聚甲基丙烯酸丁酯共聚体水分散体(PUBMA).研究了PBMA-OH含量对PUBMA水分散体及其薄膜性能的影响.结果表明成功制备了聚氨酯-聚甲基丙烯酸丁酯共聚体水分散体.随着PBMA-OH含量的增加,乳液粒径增大,分布变宽;力学性能和耐水性测试表明其薄膜的拉伸强度增大,从6 MPa增强至8 MPa,断裂伸长率降低,由1500％降至800％,耐水性变好.通过原子力显微镜(AFM)和动态热机械分析(DMA)测试说明PUBMA呈现两相分离形态,并且随着PBMA-OH的含量增加,PUBMA的玻璃化转变温度升高.     

改性苯丙乳液的合成及用于浸渍滤纸的研究

油品中的微量水分是降低油品质量,威胁发动机安全寿命的主要因素。为了制备优良的油水分离滤纸,本研究首先采用半连续乳液聚合法合成改性苯丙乳液,研究了乳化剂用量及比例、引发剂用量等对乳液稳定性的影响。结果显示,复合乳化剂用量为0.8-1.0 wt%,引发剂用量为0.8 wt%,交联单体用量为3 wt%,反应温度为80℃时,制备的改性苯丙乳液具有良好的稳定性,乳液粒径分布均匀。在上胶量为20±0.5 wt%时,此乳液浸渍的滤纸耐破度为304 kPa,拉伸强度为4.18 kN.m~(-1),耐水时间为24.0 h。水滴在浸渍滤纸表面上的接触角为110.2°,而煤油的接触角为25.6°。本研究为改性苯丙乳液在发动机滤纸上的应用提供了基础数据。     

渗透型改性环氧灌浆材料

以环氧树脂为主剂、脂肪族多胺为固化剂,以糠酮树脂、活性稀释剂糠醛丙酮、硅烷、Mannich型酚醛胺为主要改性材料的改性环氧灌浆材料,具有优异的渗透性,结合适当的施工工艺,可获得固化时间可调、固化物强度符合实际工程的渗透型改性环氧灌浆材料,并可用作多种用途。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.