Effect of arrangement of nano and micro barium titanate (BaTiO3) particles on the enhanced dielectric constant of high‐density polyethylene (HDPE)/BaTiO3

The aim of this study is to improve the dielectric and mechanical properties of HDPE/BaTiO₃ composites by binary BaTiO₃ particles, when the volume fraction of BaTiO₃ is constant. In this study, it was found that the pack density of binary BaTiO₃ particles in HDPE/BaTiO₃ composite relies on particle ratio and volume fraction of small particles. It is found that the addition of 50 vol % 1600 nm BaTiO₃ particles can boost the dielectric constant of HDPE control from 2 to 30 (14 times higher) at 40 Hz and 19 (8.5 times higher) at 40 MHz, respectively. When the particle ratio was 4, the substitution of 10 vol % 1600 nm BaTiO₃ particles by 10 vol % 400 nm BaTiO₃ particles can further enhance the dielectric constant of HDPE/L‐BT (10/10) from 30 to 50 (67% increase) at 40 Hz and from 19 to 42 (121% increase) at 40 MHz, respectively, without greatly influencing the volume resistivity of HDPE composites. In addition, the thermal conductivity of HDPE with binary BaTiO₃ particles were all above 2.0 W/(m•K). © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 1101–1108     

Reduced percolation thresholds of immiscible conductive blends

The DC conductivity of polymer blends composed of poly(ethylene‐co‐vinyl acetate) (EVA) and high density polyethylene (HDPE), where a conductive carbon black (CB) had been preferentially blended into the HDPE, were investigated to establish the percolation characteristics. The blends exhibited reduced percolation thresholds and enhanced conductivities above that of the individually carbon filled HDPE and EVA. The percolation threshold of the EVA/HDPE/CB composites was between 3.6 and 4.2 wt % carbon black, where the volume resistivity changed by 8 orders of magnitude. This threshold is at a significantly lower carbon content than the individually filled HDPE or EVA. At a carbon black loading of 4.8 wt %, the EVA/HDPE/CB composite exhibits a volume resistivity which is approximately 14 and 11 orders of magnitude lower than the HDPE/CB and EVA/CB systems, respectively, at the same level of incorporated carbon black. The dielectric response of the ternary composites, at a temperature of 23°C and frequency of 1 kHz, exhibited an abrupt increase of ca. 252% at a carbon concentration of 4.8 wt %, suggesting that the percolation threshold is somewhat higher than the range predicted from DC conductivity measurements. Percolating composites with increasing levels of carbon black exhibit significantly greater relative permittivity and dielectric loss factors, with the composite containing 6 wt % of carbon black having a value of ϵ′ ≈ 79 and ϵ″ ≈ 14. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1899–1910, 1999     

Synthesis of PVDF/BiFeO3 nanocomposite and observation of enhanced electrical conductivity and low‐loss dielectric permittivity at percolation threshold

A novel two‐phase polymer nanocomposite film comprising of polyvinylidene fluoride (PVDF) and nanocrystalline (～90 nm) semiconducting multiferroic BiFeO₃ (BFO) have been fabricated by hot‐molding technique. Such flexible thick nanocomposite films, semicrystalline in nature, exhibited extraordinarily high effective dielectric permittivity ε_eff ～ 10³ (compared with that of pure PVDF) near the low percolation threshold (f_c = 0.12) at room temperature (RT) and the films also possessed low dielectric loss (～0.18). The polarization‐electric field (P‐E) hysteresis loops are displayed at RT, which indicate ferroelectric like behavior of PVDF still persists in the percolative nanocomposite. There is also large increase of remanent polarization of BFO in the composite indicating improvement of the multiferroic behavior of BFO embedded in the PVDF polymer. The sample also indicates good fatigue endurance. Formation of microcapacitors and percolative behavior are correlated to explain the obtained results based on the special geometry of the BFO nanofillers. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Electric,dielectric, and dynamic mechanical behavior of carbon black/styrene‐butadiene‐styrene composites

The conductivity of styrene‐butadiene‐styrene block copolymers containing different amounts of extraconductive carbon black (CB) was investigated as a function of the mold temperature. The composites exhibited reduced percolation thresholds (between 1.0 and 2.0 vol % CB). The dynamic mechanical analysis characterization revealed that the glass‐rubber‐transition temperatures of both segments were not affected by the CB addition, although the damping of the polybutadiene phase displayed a progressive drop with an increase in the CB concentration. The normalized curves of tan δ/tan δ_max (where tan δ represents the value of the loss tangent at any measurement temperature and tan δ_max represents the loss tangent peak value at the corresponding temperature T_max) versus T/T_max (where T is the temperature and T_max is the maximum temperature), corresponding to both polystyrene and polybutadiene phases as well as the activation energy related to the glass‐rubber‐transition process, did not present any significant change with the addition of CB. The dielectric analysis revealed the presence of two relaxation peaks in the composite containing 1.5 vol % CB, the magnitude of which was strongly influenced by the frequency, being attributed to interfacial Maxwell‐Wagner‐Sillars relaxations caused by the presence of different interfaces in the composite. The mechanical properties were not affected by the presence of CB at concentrations of up to 2.5 vol %. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2983–2997, 2003     

Effect of AlN content on the performance of brominated epoxy resin for printed circuit board substrate

Polymer matrix composites, based on brominated epoxy, a type of material widely used in printed circuit boards (PCBs), as matrix and AlN particle as filler were prepared. The influences of AlN content on the mechanical, thermal, and electrical properties of the composites were investigated by uniaxial tensile test, TMA, thermal conductivity measurement, DMA, and dielectric properties measurement. It was found that the properties of composites monotonically varied with AlN content except that maximum tensile strength and strain of composites corresponded to a filler content of 10 wt %. The results of DMA also showed the AlN reinforcement was more pronounced above T_g, and the peak area of tan δ versus T curves decreased with AlN content, which implied the damping capacity of the composite gradually decreased. The increase in T_g and decrease in damping were probably due to strong interaction between the AlN and epoxy matrix inhibiting the mobility of the epoxy chain. In addition, different theoretical models reported in the literature were used to predict the E, CTE, k, and D_k, and compared with the experimental data. Finally, suitable models were recommended in the present materials system. For the significant improvement of performance of epoxy, we can conclude that these composite materials may be promising for PCB substrate. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1662–1674, 2007     

Temperature-dependent dielectric relaxation study of binary mixture using the time domain reflectometry method

Dielectric relaxation study of N,N-dimethylformamide (DMF) has been carried out with butylene glycol (BLG, i.e. 1,4-butanediol) at different temperatures. Time domain reflectometry in reflection mode has been used to measure the reflection coefficient in the frequency range from 10?MHz to 20?GHz. The dielectric parameters, static dielectric permittivity (ε ₀) and relaxation time (τ), have been obtained by Fourier transform and least squares fit methods. The experimental results show non-linear variation in dielectric permittivity, and relaxation time with volume fraction of BLG confirms the structural formation due to the intermolecular interaction between DMF and BLG. The variations in excess permittivity (ε^E ), excess inverse relaxation times (1/τ) ^E and Kirkwood correlation factors (g ^eff?;g?^f ) for the binary mixtures have also been reported in this article.     

Fluoropolyethers end‐capped by polar functional groups. II. Effect of catalyst and reagents concentration,solvent nature,and temperature on reaction kinetics of α,ω‐bis(hydroxy)‐terminated fluoropolyethers with cycloalyphatic and aromatic diisocyanates

A comparative kinetic study of the dibutyltin dilaurate (DBTDL) and 1,4‐diazabicyclo[2,2,2]octane (DABCO) catalyzed reactions of α,ω‐bis(hydroxy)‐terminated fluoropolyethers (FPEs)—Z‐DOLs and Z‐DOL TXs—of various molecular weights and purity, with 4,4′‐dicyclohexylmethane diisocyanate (H₁₂MDI), isophorone diisocyanate (IPDI) and 2,4‐toluene diisocyanate (TDI) was carried out in different solvents. An analytical method was used to follow the kinetics of the reactions at four different temperatures. The rate of NCO disappearance measured by two independent methods—IR spectroscopy and chemical titration were found to be very close. Straight proportionality between rate constants k_cat and catalyst concentration was found. But in some cases for the DBTDL catalyzed reactions effect of catalyst saturation along with appearance of the limiting DBTDL concentration C_lim below which the rate of reaction was close to zero were observed. Reactivity of Z‐DOLs in the tin‐catalyzed urethane reactions was found to decrease with their storage time at RT due to the slow hydrolysis of the end  COOR groups impurities, which give the corresponding acids that act as a strong inhibitor of the DBTDL activity. These acid admixtures have no influence on the DABCO catalyzed reactions. For the DBTDL and DABCO catalyzed reactions of Z‐DOLs with IPDI the dependence of effective rate constants k_eff (where k_eff = k_cat · 0.01/[DBTDL] and catalyst concentration is taken in mol % based on IPDI) on total reagents concentration were found to be described by curves with a maximum. Critical reagents concentration, after which the relationship k_eff = f (C) changes from proportional to inverse proportional, seems do not substantially depend on the solvent nature. Hydrogenated analog poly(ethylene glycol) MW 400 (PEG‐400) differs greatly from Z‐DOLs: only steady decrease of k_eff was observed with increase of reagents concentration C from 5 up to 95 wt %. Activation energies for all the studied reactions are within the range of 10.8–16.7 kcal/mol. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2579–2602, 2000     

Dielectric relaxation study of N -methyl formamide with glycols using time domain reflectometry technique

The dielectric relaxation study that is static dielectric permittivity (∈₀) and relaxation time (τ) of amide of N-methyl formamide (NMF) with increasing volume percent propylene glycol (PLG) and BLG has been carried out at different temperatures. The time domain reflectometry (TDR) technique has been used to measure reflection coefficient in frequency range of 10 MHz to 20 GHz. The dielectric parameters have been obtained by fitting experimental data with the Havriliak–Negami equation. The experimental observation shows that the static dielectric permittivity and relaxation time decreases with increasing temperature. The experimental observation also shows that the static dielectric permittivity decreases and relaxation time increases with increasing percentage volume of Propylene glycol (PLG) and Butylene glycol (BLG) in NMF. The nature of (?₀) and (τ) is same for the temperature ranges (20, 30, and 40°C). The thermodynamic parameters enthalpy (ΔH) and entropy (ΔS) of the binary mixture are also reported in this work.     

Syntheses,structures, dielectric and ferroelectric properties of a chiral coordination compound with m-nitro-benzoic acid

One polar noncentrosymmetric complex, [Zn(phen)(H₂O)₂L]L (HL = m-nitro-benzoic acid, phen = 1,10-phenanthroline) has been prepared and characterized. The title complex is crystallized in a noncentrosymmetric space group P2₁. The compound is a typical ferroelectric and its electric hysteresis loop shows a remnant polarization (P _r) of ca. 0.04?μC?cm^?2 and coercive field (E _c) of 1.26?V/cm. It may be a potential ferroelectric with a relatively large spontaneous polarization (P _s) of 0.11?μC?cm^?2. Moreover, permittivity property measurements reveal a dielectric constant (? _r) of 5.63 and dielectric loss (tan δ) of 2.5%.     

Improving the gas barrier,mechanical and thermal properties of poly(vinyl alcohol) with molybdenum disulfide nanosheets

New multifunctional materials with both high structural and gas barrier performances are important for a range of applications. Herein we present a one‐step mechanochemical process to prepare molybdenum disulfide (MoS₂) nanosheets with hydroxy functional groups that can simultaneously improve mechanical strength, thermal conductivity, and gas permittivity of a polymer composite. By homogeneously incorporating these functionalized MoS₂ nanosheets at low loading of less than 1 vol %, a poly(vinyl alcohol) (PVA) polymer exhibits elongation at break of 154%, toughness of 82 MJ/m³, and in‐plane thermal conductivity of 2.31 W/m K. Furthermore, this composite exhibits significant gas barrier performance, reducing the permeability of helium by 95%. Under fire condition, the MoS₂ nanosheets form thermally stable char, thus enhancing the material's resistance to fire. Hydrogen bonding has been identified as the main interaction mechanism between the nanofillers and the polymer matrix. The present results suggest that the PVA composite reinforced with 2D layered nanomaterial offers great potentials in packaging and fire retardant applications. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 406–414     

Estimation of the agglomeration structure for conductive particles and fiber‐filled high‐density polyethylene through dynamic rheological measurements

A study on the correlation between electrical percolation and viscoelastic percolation for carbon black (CB) and carbon fiber (CF) filled high‐density polyethylene (HDPE) conductive composites was carried out through an examination of the filler concentration (?) dependence of the volume resistivity (ρ) and dynamic viscoelastic functions. For CB/HDPE composites, when ? was higher than the modulus percolation threshold (?_G ～ 15 vol %), the dynamic storage modulus (G′) reached a plateau at low frequencies. The relationship between ρ and the normalized dynamic storage modulus (G_c^′/G_p^′, where G_c^′ and G_p^′ are the dynamic storage moduli of the composites and the polymer matrix, respectively) was studied. When ? approached a critical value (?_r), a characteristic change in G_c^′/G_p^′ appeared. The critical value (G_c^′/G^′_p)c was 9.80, and the corresponding ?_r value was 10 vol %. There also existed a ? dependence of the dynamic loss tangent (tan δ) and a peak in a plot of tan δ versus the frequency when ? approached a loss‐angle percolation (?_δ = 9 vol %). With parameter K substituted for A, a modified Kerner–Nielson equation was obtained and used to analyze the formation of the network structure. The viscoelastic percolation for CB/HDPE composites could be verified on the basis of the modified equation, whereas no similar percolation was found for CF/HDPE composites. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1199–1205, 2004     

Thermorheological analysis of PVC blends

The effect of temperature on dynamic viscoelastic measurements of miscible poly (vinyl chloride) (PVC)/ethylene‐vinyl acetate–carbon monoxide terpolymer (EVA‐CO) and immiscible PVC/high‐density polyethylene (HDPE) and PVC/chlorinated polyethylene (CPE) molten blends is discussed. PVC plasticized with di(2 ethyl hexyl) phthalate (PVC/DOP) and CaCO₃ filled HDPE (HDPE/CaCO₃) are also considered for comparison purposes. Thermorheological complexity is analyzed using two time–temperature superposition methods: double logarithmic plots of storage modulus, G′, vs. loss modulus, G″, and loss tangent, tan δ, vs. complex modulus, G*, plots. Both methods reveal that miscible PVC/EVA‐CO and PVC/DOP systems are thermorheologically complex, which is explained by the capacity of PVC to form microdomains or crystallites during mixing and following cooling of the blends. For immiscible PVC/HDPE and PVC/CPE blends the results of log G′ vs. log G″ show temperature independence. However, when tan δ vs. log G* plots are used, the immiscible blends are shown to be thermorheologically complex, indicating that the morphology observed by microscopy and constitued by a PVC phase dispersed in a HDPE or CPE matrix, is reflected by this rheological technique. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 469–477, 2000     

Study of electrical,mechanical, and nanoscale free‐volume properties of NBR and EPDM rubber reinforced by bentonite or kaolin

The effect of Na bentonite, Ca bentonite, and kaolin fillers on the macrostructure and microstructure of acrylonitrile butadiene rubber, ethylene propylene diene rubber, and their blend (50/50) was studied through electrical and mechanical measurements, as well as with positron annihilation lifetime spectroscopy. The real part of permittivity (ε′), dielectric loss (ε″), and the crosslinking density were found to increase with increasing filler content. The increase of crosslinking density of the blend with increasing amount of fillers reflects a decrease in the equilibrium swelling up to 21.50 wt % compared with that of the unfilled blends. The mechanical investigation showed pronounced increase in the tensile strength, and in elongation at break with the addition of up to 21.50 wt % of filler. In addition, comparing between different fillers showed that the reinforcing effect of Na bentonite is more effective than Ca bentonite and kaolin but the physico‐mechanical of Ca bentonite is less than that for kaolin. The positron annihilation lifetime measurements revealed that the free‐volume properties were strongly affected by the amount and type of filler, in particular, the free‐volume fraction was dramatically decreased with increasing filler content. Furthermore, correlations were made between the free‐volume parameters and both electrical and mechanical properties. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1825–1838, 2009     

Dielectric loss of high-density polyethylene below 4.2°K

Drawing of oxidized high-density polyethylene (HDPE) and subsequent annealing greatly reduce the low-temperature dielectric loss when the electric field is applied perpendicular to the draw direction. This supports our model (J. Polym. Sci. Polym. Phys. Ed., 15 , 43 (1977)) of the proton moving parallel to the c axis of the PE crystal. A particular antioxidant (Ionox 330) in unoxidized HDPE induces a dielectric loss with a frequency and temperature dependence which differs from that for the loss in oxidized HDPE. The antioxidant loss seems to be an overlapping of tunneling and a thermal activation process. The possibility that the hydroperoxide group in the PE crystal is the origin of the loss in oxidized HDPE was theoretically examined in a manner similar to that used for the hydroxyl group in the previous paper. Results suggest that the hydroperoxide group is less probable than hydroxyl as the origin of the low-frequency loss in HDPE.     

Synthesis and characterization of high nitrile content polyimides as dielectric films for electrical energy storage

Three new isomeric diamines containing three, oxy‐linked benzonitriles (3BCN), one of which is asymmetric (meta, para, or m, p), are synthesized in a 3‐step sequence. Polycondensation of these diamines and four common dianhydrides (6FDA, OPDA, BTDA, and PMDA) in N,N‐dimethylacetamide via poly(amic acid) precursors and thermal curing at temperatures up to 300 °C lead to three series of tough, creasable polyimide (PI) films (tensile moduli = 1.63 ? 2.86 GPa). Among these PIs, two PMDA‐based PIs possess relatively high crystallinity and two OPDA‐based PIs, low crystallinity, whereas all 6FDA‐ and BTDA‐based PIs, and m,m‐3BCN‐OPDA‐PI are amorphous, readily soluble in common polar aprotic solvents. Thermally stable and having high T_g (216 ? 341 °C), these PIs lose 5% weight around 493–503 °C in air and 463–492 °C in nitrogen. Dielectric properties have been evaluated by broadband dielectric spectroscopy (BDS) and electric displacement‐electric‐field (D‐E) loop measurements. D‐E loop results show an increase in high temperature permittivity (at 190 °C/1 kHz) from 2.9 (for parent PI CP2 with no nitrile group) to as high as 4.9 for these PIs, while keeping their dielectric loss relatively low. Thus, an increase in dipole moment density by the presence of three neighboring CN per repeat unit can increase the overall permittivity, which could be further enhanced by sub‐T_g mobility of para‐phenylene linkages (BDS results). Published 2014. J. Polym. Sci., Part A: Polym. Chem. 2014 J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 422–436     

Dielectric properties of PANI-PEG nanocomposites filled with silica media for antistatic applications

The dielectric investigations of porous synthetic silica gel modified with polyaniline (PANI) and polyethylene glycol (PEG) polyblend at various concentrations are demonstrated in this paper. By using the chemical oxidative process to embed polyaniline (PANI) and polyethylene glycol (PEG) into a silica matrix, conducting gel nanocomposites were synthesized. For various dopant concentrations, the dielectric permittivity (ε′), D.C. conductivity (σ_dc), loss tangent (tanδ) and dielectric loss (ε″) were investigated. The samples were characterized using differential thermal analysis/thermogravimetric analysis, Fourier transform infrared spectroscopy and high-resolution transmission electron microscopy. Depending on the co-blend content, PANI-PEG modified silica structures produce nanoparticles ranging in size from 9.9 to 48.1 nm. The variation of DC conductivity (σ_dc) with PANI/PEG content shows Maxwell-Wagner Sillars (MWS) effect confirming the role of the conjugation and the structural order.     

Preparation and properties of silylated PTFE/SiO2 organic–inorganic hybrids via sol–gel process

A study on poly(tetrafluoroethylene) (PTFE) reinforced with tetraethoxysilanes (TEOS) derived SiO₂ is described. It included the manufacturing process of SiO₂‐reinforced PTFE and the effects of silylation agent on the properties of the hybrid material, such as porosity, hydrophobic, thermal resistance, dielectric and mechanical properties, and microstructure. PTFE/SiO₂ hybrids of 50 wt % SiO₂ loading were prepared via a sol–gel process and were shaped by a two‐roll milling machine. Trimethylchlorosilane and hexamethydisilazane were used as the silylation agents. Our results showed that the water absorption and dielectric loss of PTFE/SiO₂ hybrid had significantly improved with silylation agent. The silylation process replaced Si? OH with Si? CH₃ on the surface of the TEOS‐derived silica colloidal particle. The existence of trimethylsilyl [? Si(CH₃)₃] on the surface of the modified PTFE/SiO₂ hybrid was confirmed via infrared and solid‐state ²⁹Si magic‐angle spinning nuclear magnetic resonance spectra. Nitrogen‐sorption techniques were used to characterize the modified and unmodified PTFE/SiO₂ hybrids. The microstructure of SiO₂ in the matrix was also evaluated with scanning electron microscopy and transmission electron microscopy. Our results showed that the silylated sol–gel‐derived PTFE/SiO₂ hybrids had exhibited high porosity (53.7%) with nanosize pores (10–40 nm) and nanosize colloidal particles (20–50 nm). This manifests itself as have the ultralow dielectric properties (D_k = 1.9 and D_f = 0.0021), low coefficient of thermal expansion (66.5 ppm/°C), high tensile modulus (141 MPa), excellent thermal resistance (T_d = 612 °C), and an increased hydrophobia (θ = 114°); moreover, the hydrophobic property of the PTFE/SiO₂ hybrid was thermally stable up to 400 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1789–1807, 2004     

Synthesis,characterization, and properties of polyurethanes containing 1,4:3,6‐dianhydro‐D‐sorbitol

Two‐ and three‐component polyurethanes containing 1,4:3,6‐dianhydro‐D ‐sorbitol (isosorbide) derived from glucose were synthesized using n‐BuSn(?O)OH·H₂O as a catalyst, and the thermal properties (T_g, T_d) of the polymers were investigated by differential scanning calorimetry and thermogravimetric analysis. We carried out molds for polyurethanes, the molds of polyurethanes were obtained. The dynamic mechanical analyzes showed that the storage modulus values of the three‐component polymers were constant to a higher temperature than those of the two‐component polymers. The storage moduli (E′), loss moduli (E″), and values of tan δ for the polymers were obtained. The rigidity of three‐component polymers was increased by the introduction of bisphenol A and diphenylmethane group to two‐component polymer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6025–6031, 2009     

Effects of thermal volume expansion on positive temperature coefficient effect for carbon black filled polymer composites

Polymeric positive temperature coefficient (PTC) materials have been prepared by incorporating carbon black (CB) into two different polymer matrices, crystalline high density polyethylene (HDPE) and amorphous polystyrene (PS). The effects of thermal volume expansion on the electrical properties of conductive polymer composites were studied. The volume fraction of conductive particles behaves like a switch from insulator to conductor in the polymeric PTC composite. Our mathematical model and experimental model have proved that the abrupt resistivity increase at PTC transition range and at the percolation curve close to the critical volume fraction for both polymeric PTC composites have the same conductive mechanism. The thermal expansion is one of the key factors responsible for the PTC effect and can be seen by comparing the PTC transition curves from model predictions and experiment. Furthermore, the model predicts PTC curves of CB/PS composite more successfully than it does for the CB/HDPE composite, and the reasons for this are also discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3078–3083, 2007     

Hyperbranched polybenzoxazoles incorporated polybenzoxazoles for high‐performance and low‐K materials

This paper reports an effective approach for the fabrication of low‐k polybenzoxazole (PBO) by covalent incorporation of hyperbranched PBO (HBPBO). Soluble o‐aminophenol‐terminated HBPBO was first synthesized by a one‐pot polycondensation, then covalently bonded to poly(hydroxyamide) ended with carbonyl chloride groups, PBO was finally obtained by thermal conversion of the precursor polymers. It was demonstrated that the thermal stability of PBO was not influenced by the incorporation of HBPBO due to their similar chemical compositions, while the glass transition temperature, elastic modulus and hardness were improved because of the linking effects of HBPBO to linear PBO chains. The dielectric constant of PBO was significantly reduced due to the disturbed chain packing of PBO by the globular HBPBO, and the intrinsic cavities in HBPBO, which increased free volume in the materials. Moreover, the material also exhibited reduced coefficient of thermal expansion as compared to neat PBO and low water absorption. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1623–1632