Crystallization behavior of isotactic propylene‐1‐hexene random copolymer revealed by time‐resolved SAXS/WAXD techniques

The crystallization behavior of isotactic propylene‐1‐hexene (PH) random copolymer having 5.7% mole fraction of hexene content was investigated using simultaneous time‐resolved small‐angle X‐ray scattering (SAXS) and wide‐angle X‐ray diffraction (WAXD) techniques. For this copolymer, the hexene component cannot be incorporated into the unit cell structure of isotactic polypropylene (iPP). Only α‐phase crystal form of iPP was observed when samples were melt crystallized at temperatures of 40 °C, 60 °C, 80 °C, and 100 °C. Comprehensive analysis of SAXS and WAXD profiles indicated that the crystalline morphology is correlated with crystallization temperature. At high temperatures (e.g., 100 °C) the dominant morphology is the lamellar structure; while at low temperatures (e.g., 40 °C) only highly disordered small crystal blocks can be formed. These morphologies are kinetically controlled. Under a small degree of supercooling (the corresponding iPP crystallization rate is slow), a segmental segregation between iPP and hexene components probably takes place, leading to the formation of iPP lamellar crystals with a higher degree of order. In contrast, under a large degree of supercooling (the corresponding iPP crystallization rate is fast), defective small crystal blocks are favored due to the large thermodynamic driving force and low chain mobility. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 26–32, 2010     

Structure development in multistage stretching of PTFE films

The structure of expanded poly(tetrafluoroethylene) (ePTFE) films that were produced by uniaxial or biaxial stretching of a calendared sheet were studied by wide angle X‐ray diffraction (WAXD), small angle X‐ray scattering, differential scanning calorimetry (DSC), and scanning electron microscopy. The molecular orientation of the stretched films was analyzed by WAXD flat films and pole figures. Biaxial orientation factors were computed to interpret the level of orientation quantitatively. DSC scans showed that oriented samples exhibited two melting peaks, one at the commonly observed temperature in the range 340–345 °C and one around 380 °C. The possible causes of this high‐temperature melting peak and its relation to previously described processes is discussed. The microporous nature of the ePTFE films is also briefly discussed. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Solidification of syndiotactic polystyrene by a continuous cooling transformation approach

Syndiotactic polystyrene (sPS) was solidified from the melt under drastic conditions according to a continuous cooling transformation methodology developed by the authors, which covered a cooling rate range spanning from approximately 0.03 to 3000 °C/s. The samples produced, structurally homogeneous across both their thickness and surface, were analyzed by macroscopic methods, such as density, wide‐angle X‐ray diffraction (WAXD), and microhardness (MH) measurements. The density was strictly related to the phase content, as confirmed by WAXD deconvolution. The peculiar behavior encountered (the density first decreasing and then increasing with the cooling rate) was attributed to the singularity of the phases formed in sPS; that is, one of the crystalline phases (α) was less dense than the amorphous phase, and the latter, in turn, was less dense than the other crystalline phase (β). With an increasing cooling rate, the thermodynamically stable phase (β) disappeared first, and it was followed by the α phase. On the other hand, the MH values remarkably depended on the amount of the β phase, the α‐phase content influencing the mechanical properties only to a minor extent. The behavior of the crystallization kinetics was described through a modified multiphase Kolmogoroff–Avrami–Evans model for nonisothermal crystallization. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2688–2699, 2007     

Copolymerization of propylene with higher α‐olefins in the presence of the syndiospecific catalyst i‐Pr(Cp)(9‐Flu)ZrCl2/MAO

The catalyst system i‐Pr(Cp)(9‐Flu)ZrCl₂/methylaluminoxane was used for the synthesis of random syndiotactic copolymers of propylene with 1‐hexene, 1‐dodecene, and 1‐octadecene as comonomers. An investigation of the microstructure by ¹³C NMR spectroscopy revealed that the stereoregularity of the copolymers decreased because of an increase in skipped insertions in the presence of the higher 1‐olefin. The melting temperature of the copolymers, as measured by differential scanning calorimetry (DSC), decreased linearly with increasing comonomer content independently of the comonomer nature. During the DSC heating cycle, an exothermic peak indicating a crystallization process was observed. The decrease in the crystallization temperature with higher 1‐olefin content, measured by crystallization analysis fractionation, indicated a small but significant dependence on the nature of the comonomer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 128–140, 2002     

Poly(propylene isophthalate), poly(propylene succinate), and their random copolymers: Synthesis and thermal properties

Poly(propylene isophthalate) (PPI), poly(propylene succinate) (PPS), and poly(propylene isophthalate/succinate) (PPI‐PPS) random copolymers were synthesized and characterized in terms of chemical structure and molecular weight. The thermal behavior was examined by TGA and DSC. All the polymers showed a good thermal stability. At room temperature, they appeared as semicrystalline materials, except 20PPI‐PPS and 30PPI‐PPS: the main effect of copolymerization was a lowering in the amount of crystallinity and a decrease of T_m with respect to homopolymers. A crystalline phase of PPI and PPS was evidenced at high content of PI or PS units, respectively. Amorphous samples were obtained after melt quenching and an increment of T_g, with the increment of PI units, was observed. This behavior was explained as due to the presence of stiff phenylene groups. The Wood equation described well T_g‐composition data. Lastly, the presence of a rigid‐amorphous phase was evidenced in copolymers, differently from the two homopolymers. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 310–321, 2007.     

Synthesis of polyethylene and polypropylene containing fluorene units in the side chain

Copolymerizations of ethylene or propylene and allyl monomers containing 9‐fluorenyl group, diallyl‐di‐9‐fluorenylsilane (DAFS), 9,9‐diallylfluorene (DAF), and 9‐allylfluorene (AF), were investigated with various zirconocene catalysts using methylaluminoxane as a cocatalyst. The bridged zirconocene catalysts, especially a syndioselective catalyst, showed a higher reactivity for all the comonomers than the nonbridged catalysts. DAFS was mainly incorporated into the polymer chain via cyclization insertion, whereas DAF was copolymerized via both 1,2‐ and cyclization insertions. Cyclization selectivity, ratio of cyclized insertion unit, of DAF in the copolymerization with propylene was higher than that in the copolymerization with ethylene. Copolymerization with AF yielded low‐molecular weight copolymer because of frequent chain transfer reaction. Optical properties of the propylene based‐copolymers were investigated by UV‐vis and photoluminescence spectroscopy, and absorption‐ and emission‐derived from fluorenyl groups were detected in the copolymers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3542–3552, 2010     

Effect of the γ‐form crystal on the thermal fractionation of poly(propylene‐co‐ethylene)

The effect of the γ‐form crystal on the thermal fractionation of a commercial poly(propylene‐co‐ethylene) (PPE) has been studied by differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction (WAXD) techniques. Two thermal fractionation techniques, stepwise isothermal crystallization (SIC) and successive self‐nucleation and annealing (SSA), have been used to characterize the molecular heterogeneity of the PPE. The results indicate that the SSA technique possesses a stronger fractionation ability than that of the SIC technique. The heating scan of the SSA fractionated sample exhibits 12 endothermic peaks, whereas the scan of the SIC fractionated sample only shows eight melting peaks. The WAXD observations of the fractionated PPE samples prove that the content of the γ‐form crystals formed during the thermal treatment of the SIC technique is much higher than that of the SSA treatment. The former is 57.4%, whereas the later is 12.6%. The effect of theγ‐form crystals on thermal fractionation ability is discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4320–4325, 2004     

Preferential formation of electroactive crystalline phases in poly(vinylidene fluoride)/organically modified silicate nanocomposites

The role of organically modified silicate (OMS), Lucentite STN on the formation of β‐crystalline phase of poly(vinylidene fluoride) (PVDF) is investigated in the present study. The OMS was solution blended with PVDF and cast on glass slide to form PVDF‐OMS nanocomposites. Solution cast samples were subjected to various thermal treatments including annealing (AC‐AN), melt‐quenching followed by annealing (MQ‐AN), and melt‐slow cooling (MSC). Fourier‐transform infrared spectroscopy (FT‐IR), wide angle X‐ray diffraction (WAXD), and differential scanning calorimetry (DSC) were used to investigate the crystalline structure of thermally treated samples. As a special effort, the combination of in situ thermal FT‐IR, WAXD, and DSC studies was utilized to clearly assess the thermal properties. FT‐IR and WAXD results of MQ‐AN samples revealed the presence of β‐phase of PVDF. Ion‐dipole interaction between the exfoliated clay nanolayers and PVDF was considered as a main factor for the formation of β‐phase. Melt‐crystallization temperature and subsequent melting point were enhanced by the addition of OMS. Solid β‐ to γ‐crystal phase transition was observed from in situ FT‐IR and WAXD curves when the representative MQ‐AN sample was subjected to thermal scanning. Upon heating, β‐phase was found to disappear through transformation to the thermodynamically stable γ‐phase rather than melting directly. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2173–2187, 2008     

Crystallization kinetics and morphology of biodegradable poly(butylene succinate‐co‐propylene succinate)s

The crystallization behavior of biodegradable poly(butylene succinate) and copolyesters poly(butylene succinate‐co‐propylene succinate)s (PBSPS) was investigated by using ¹H NMR, DSC and POM, respectively. Isothermal crystallization kinetics of the polyesters has been analyzed by the Avrami equation. The 2.2‐2.8 range of Avrami exponential n indicated that the crystallization mechanism was a heterogeneous nucleation with spherical growth geometry in the crystallization process of polyesters. Multiple melting peaks were observed during heating process after isothermal crystallization, and it could be explained by the melting and recrystallization model. PBSPS was identified to have the same crystal structure with that of PBS by using wide‐angle X‐ray diffraction (WAXD), suggesting that only BS unit crystallized while the PS unit was in an amorphous state. The crystal structure of polyesters was not affected by the crystallization temperatures, too. Besides the normal extinction crosses under the POM, the double‐banded extinction patterns with periodic distance along the radial direction were also observed in the spherulites of PBS and PBSPS. The morphology of spherulites strongly depended on the crystallization temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 420–428, 2007     

Ductile–brittle‐transition phenomenon in polypropylene/ethylene‐propylene‐diene rubber blends obtained by dynamic packing injection molding: A new understanding of the rubber‐toughening mechanism

For a more complete understanding of the toughening mechanism of polypropylene (PP)/ethylene‐propylene‐diene rubber (EPDM) blends, dynamic packing injection molding was used to control the phase morphology and rubber particle orientation in the matrix. The relative impact strength of the blends increased at low EPDM contents, and then a definite ductile–brittle (D–B) transition was observed when the EPDM content reached 25 wt %, at which point blends should fail in the ductile mode with conventional molding. Wide‐angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), and scanning electron microscopy (SEM) were used to investigate the shear‐induced crystal structure, morphology, orientation, and phase separation of the blends. WAXD results showed that the observed D–B transition took place mainly for a constant crystal structure (α form). Also, no remarkable changes in the crystallinity and melting point of PP were observed by DSC. The highly oriented and elongated rubber particles were seen via SEM at high EPDM contents. Our results suggest that Wu's criterion is no longer valid when dispersed rubber particles are elongated and oriented. The possible fracture mechanism is discussed on the basis of the stress concentration in a filler‐dispersed matrix. It can be concluded that not only the interparticle distance but also the stress fields around individual particles play an important role in polymer toughening. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2086–2097, 2002     

Long‐term X‐ray stimulated crystallization of poly(N‐methyldodecano‐12‐lactam) in blend with poly(styrene‐stat‐acrylic acid)

The effect of X‐ray irradiation on crystallization of the blend of poly(N‐methyldodecano‐12‐lactam) (PMDL) with 29.5% of statistical copolymer poly(styrene‐stat‐acrylic acid) (PSAA) was studied using DSC, WAXD, and solid‐state ¹³C NMR methods. Significant acceleration of crystallization was found in the as‐prepared X‐ray irradiated (XI), that is, WAXD‐measured, samples compared with the nonirradiated (NI) ones. In the XI blend, the incubation period was shortened and crystallization proceeded at significantly higher rate. In the asymptote, after 100–120 days, both NI and XI samples reached the same final crystallinity of about 18%. The second DSC runs indicated that the stimulating effect of X‐ray irradiation was eliminated by heating the sample during the first run. The ¹³C NMR studies have shown that PMDL chains crystallize exclusively in cis conformation on the C? N bond. Both in neat PMDL and in the blend with PSAA, the XI samples contained a significantly higher proportion of cis conformers in amorphous phase than the NI samples. It is suggested that energy absorbed by the sample during the standard WAXD measurement helps overcome the barrier of the trans/cis transition in the PMDL molecules. This opens the way to the formation of a higher number of critical equilibrium nuclei and, finally, results in accelerated crystallization of the XI samples. No irreversible changes were found in the XI samples. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 311–321, 2008     

Controlled crystallization of poly(vinylidene fluoride) chains from mixed solvents composed of its good solvent and nonsolvent

Poly(vinylidene fluoride) (PVDF) chains with the same expanded state were obtained by dissolving PVDF resin in good solvent. Then, the crystallization of PVDF chains from mixed solvents composed of its good solvent and nonsolvent was investigated. N,N‐dimethylformamide (DMF) and ethanol were used as good solvent and nonsolvent of PVDF, respectively. The crystalline phases of PVDF were characterized by Fourier transform infrared (FTIR) spectroscopy and wide angle X‐ray diffraction (WAXD). For the crystallization of PVDF chains from mixed solvents, low ethanol content favored the formation of β phase, while high ethanol content resulted predominantly in the α phase. Different crystallization morphology was observed from the scanning electron microscopy (SEM) images. The obvious spherulite morphology disappeared with the increase in ethanol content in mixed solvent. According to thermal analyses, the crystallized PVDF from mixed solvents with high ethanol content had lower onset melting temperatures than that from low ethanol content. Smaller lamellar thickness calculated from WAXD data reasoned the low onset melting temperatures. The above results indicated that the crystallization of PVDF chains from mixed solvent was a “controlled” process by ethanol content. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 575–581, 2010     

Cocrystallization phenomena in novel poly(diethylene terephthalate‐co‐thiodiethylene terephthalate) copolyesters

Poly(diethylene terephthalate‐co‐thiodiethylene terephthalate) (PDET/TDET) copolymers of various compositions were synthesized and characterized in terms of chemical structure and molecular weight. The thermal behavior was examined by thermogravimetric analysis and differential scanning calorimetry. All the polymers showed a good thermal stability. At room temperature they appeared as semicrystalline materials: the main effect of copolymerization was a lowering in the amount of crystallinity and a decrease of melting temperature with respect to homopolymers. WAXD measurements indicated that cocrystallization occurs over an extended composition range and three different crystalline phases have been identified. In particular, the applicability of Wendling–Suter's equation has been checked for the PDET/TDET copolymers with TDET unit content ranging from 60 to 90 mol %. Amorphous samples were obtained after melt quenching and a decrease of T_g as the content of TDET units is increased was observed. This behavior was explained as due to the presence of flexible C? S? C bonds in the polymeric chain. Lastly, the Fox equation well described T_g‐composition data. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1562–1571, 2006     

Structure characterization of copolymers of ethylene and 1‐octadecene

Four ethylene‐1‐octadecene copolymers and the corresponding polyethylene homopolymer, synthesized with a metallocene catalyst, have been analyzed by using three characterization techniques in the solid state: differential scanning calorimetry, wide‐angle X‐ray diffraction, and Raman spectroscopy. Very important annealing effects are observed in the copolymers with higher comonomer content while standing at room temperature, in such a way that the enthalpies of melting derived from the first and second melting are different. The X‐ray diffractograms have been analyzed in terms of amorphous and crystalline components, determining both the crystallinity and the position of the different reflections. The variation of the unit cell parameters has been calculated from those reflections. No indication of a possible participation of the relatively long 1‐octadecene branches in the crystallization can be deduced from the X‐ray data. The degree of crystallinity has also been determined from the Raman spectra, following two procedures. The results indicate that the crystallinities deduced from the band at 1416 cm⁻¹ are much lower than those derived from the other two characterization techniques. On the contrary, the data from the 1060 cm⁻¹ band are practically coincident with the X‐ray determinations. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1440–1448, 2000     

Synthesis and characterization of a series of wholly aromatic copolyesters containing 2‐(α‐phenylisopropyl)hydroquinone moiety

Two series of new wholly aromatic thermotropic copolyesters containing the 2‐(α‐phenylisopropyl)hydroquinone (PIHQ) moiety have been synthesized and their basic properties such as glass transition temperature (T_g), melting temperature (T_m), thermal stability, crystallinity, and liquid crystallinity were studied by differential scanning calorimetry (DSC), thermogravimetry (TG), and wide‐angle X‐ray diffractometry (WAXD) and on a polarizing microscope. The first series was prepared from acetylated PIHQ, terephthalic acid (TPA), and 2,6‐naphthalenedicarboxylic acid (NDA), and the second series from acetylated PIHQ, TPA, and 1,1′‐biphenyl‐4,4′‐dicarboxylic acid (BDA). The T_g values (152–168°C) of the two series are not much different, although the values for the first series appear slightly higher. The T_m values (287–378°C) and the degree of crystallinity of the first series are appreciably greater than those of the second series. Such differences can be explained by the geometric structure of NDA and BDA moieties. All of the present polyesters are thermotropic and nematic. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 881–889, 1999     

Effect of shear on the crystallization of the poly(ether ether ketone)

The effect of shear on the crystallization behavior of the poly(ether ether ketone) (PEEK) has been investigated by means of ex situ wide‐angle X‐ray diffraction (WAXD), small‐angle X‐ray scattering, and differential scanning calorimetry (DSC). The changes of the intensity of WAXD patterns along shear direction of the PEEK induced by short‐term shear were observed when the samples crystallized at 330 °C. The results showed that the dimensions of the crystallites perpendicular to the (110) and (111) planes reduced with the increase of shear rate, whereas the dimensions of the crystallites perpendicular to (200) plane increased with the increase of shear rate. Moreover, increasing shear rate can lead to the increase of the crystallinity as well as the average thickness of the crystalline layers. Correspondingly, a new melting peak at higher temperature was found during the subsequent DSC scanning when the shear rate was increased to 30 s^?1. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 220–225, 2010     

Origin of the double melting peaks of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) with a high HV content as revealed by in situ synchrotron WAXD/SAXS analyses

We here reported the dual melting behaviors with a large temperature difference more than 50 °C without discernible recrystallization endothermic peak in isomorphous poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (P(HB‐co‐HV)) with a high HV content of 36.2 mol %, and the structure evolution upon heating was monitored by in situ synchrotron wide‐angle X‐ray diffraction/small‐angle X‐ray scattering (WAXD/SAXS) to unveil the essence of such double endothermic phenomena. It illustrated that the thinner lamellae with the larger unit cell and the thicker crystals having the smaller unit cell were melted around the first low and second high melting ranges, respectively. By analyzing in situ WAXD/SAXS data, and then coupling the features of melting behavior, the evolution of the parameters of both crystal unit cell and lamellar crystals, we proposed that the thinner unstable lamellae possess a uniform structure with HV units total inclusion, and the thicker stable lamellae reflect the sandwich structure with HV units partial inclusion. It further affirmed that the thicker sandwich and thinner uniform lamellae formed during the cooling and subsequent isothermal crystallization processes, respectively. These findings fully verify that it is the change of structure of lamellae rather than the melting/recrystallization that is responsible for double melting peaks of isomorphous P(HB‐co‐36.2%HV), and enhance our understanding upon multiple endothermic behaviors of polymers. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1453–1461     

Simultaneous wide‐angle X‐ray diffraction and differential scanning calorimetry analysis of the melting and recrystallization behavior of polyethylene and isotactic polypropylene containing cyclopentane units in the main chain

The melting and crystallization behavior of polyethylene and isotactic polypropylene containing 1,2‐ or 1,3‐disubstituted cyclopentane units in the main chain has been studied with simultaneous wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry. For the ethylene‐based copolymers, the position of a reflection peak in the WAXD patterns shifts to a low angle with the increasing acquired temperature. The temperature dependence on the axial length of the crystal lattice is more marked in the copolymers forming orthorhombic crystals (containing 1,2‐cyclopentane or 5.6 mol % 1,3‐cyclopentane units) than in those forming hexagonal crystals (containing 8.1 mol % 1,3‐cyclopentane units). For the isotactic propylene‐based copolymers, the position of the reflection peaks in the WAXD patterns is independent of the acquired temperature. The proportion of the γ form in the copolymer containing the 1,2‐cyclopentane units is higher than that in the copolymers containing the 1,3‐cyclopentane units. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1457–1465, 2004     

Effect of the comonomer content on the mechanical parameters and microhardness values in poly(ethylene‐co‐1‐octadecene) synthesized by a metallocene catalyst

Stress–strain and microhardness measurements were carried out on a series of copolymers of ethylene and 1‐octadecene with different comonomer contents in the corresponding homopolymer of ethylene, synthesized with a metallocene catalyst. The different mechanical properties, deduced from the stress–strain curves (Young's modulus, yield stress, deformation at break, and energy to break) are interpreted in terms of the crystallinity and molecular weight of the samples because these two characteristics show considerable variations with the comonomer content. The microhardness values are explained in terms of these properties, and they are also correlated with Young's moduli and yield stresses deduced from the stress–strain curves. Linear relations are found between microhardness and yield stress and between the logarithm of the microhardness and the logarithm of the elastic modulus. The properties deduced from these lines are compared with literature values. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 277–285, 2001