Simple and convenient analytical method for the direct determination of chlorine species by ETV-ICP-AES using tungsten boat furnace vaporiser and exchangeable small sample cuvettes

A tungsten boat furnace vaporiser and an exchangeable sample cuvette system were applied for the direct determination of chlorine in plastic samples by electrothermal vaporisation inductively coupled plasma atomic emission spectrometry. Each piece of plastic samples was moulded into a thin film, and weighed into small sample cuvettes. An ethanolic solution of the modifier potassium hydroxide and an organic solvent were added to each sample cuvette. The contents including the plastic piece were spread over the bottom of each sample cuvette by warming on a hotplate. After the preparation, one of the cuvettes was placed in the tungsten boat furnace equipped with the electrothermal vaporiser. The temperature was gradually elevated. At the flash vaporisation step of 1800 °C, the analyte was vaporised and introduced into the ICP to measure an atomic emission assignable to Cl I 134.724 nm. A widely spread thin layer of the plastic facilitated its rapid evaporation and introduction into an ICP atomic emission spectrometer. Since all the chlorine species were on-furnace decomposed to form potassium chloride during the pretreatment, the solid samples were analysed using a calibration curve prepared from the aqueous standard solutions. By using this system, a detection limit of 1.5 μg g⁻¹ of chlorine in solid plastic samples was established when a sample amount taken of 2 mg was studied. The exchangeable sample cuvette technique makes it possible to measure a number of sample sequentially by preparing a lot of sample cuvettes prior to analysis. Approximately 20 batches could be vaporised per hour. Analytical results of some plastic samples that were analysed by this technique are given in this report.     

A new approach of direct sample-digestion before vaporization for determination of a metal in rocks by inductively coupled plasma atomic emission spectrometry.

A new approach to sample digestion, subsequent vaporization and introduction to an inductively coupled plasma (ICP) atomic emission spectrometer was developed for the direct determination of magnesium. To each small sample cuvette made of tungsten, a ground rock sample was precisely weighed. The cuvette was situated on a tungsten boat furnace. Ammonium fluoride solution was added to the cuvette as a chemical modifier. After the on-furnace digestion has been completed, the analyte, magnesium, in the cuvette was vaporized and introduced into the ICP atomic emission spectrometer. Since the powdered samples were wet-digested in the sample cuvettes prior to vaporization, they could be analyzed by using a calibration curve prepared from aqueous standard solutions. This method was applied to the determination of magnesium in several standard reference materials with satisfactory results.     

Direct determination of lead in biological samples by electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) after furnace-fusion in the sample cuvette-tungsten boat furnace

The newly conceived electrothermal vaporization (ETV) system using a tungsten boat furnace (TBF) sample cuvette was designed for the direct analysis of solid samples with detection by inductively coupled plasma mass spectrometry (ICP-MS). Into this small sample cuvette, a solid mixture of the biological samples and diammonium hydrogenphosphate powder as a fusion flux was placed and situated on a TBF. Tetramethylammonium hydroxide solution was added to the mixture. After the on-furnace digestion had been completed, the analyte in the cuvette was vaporized and introduced into the ICP mass spectrometer. The solid samples were analyzed by using a calibration curve prepared from the aqueous standard solutions. The detection limit was estimated to be 5.1 pg of lead, which corresponds to 10.2 ng g(-1) of lead in solid samples when a prepared sample amount of 1.0 mg was applied. The relative standard deviation for 8 replicate measurements obtained with 100 pg of lead was calculated to be 6.5%. The analytical results for various biological samples are described.     

Direct determination of lead in biological samples by electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) after furnace-fusion in the sample cuvette-tungsten boat furnace

The newly conceived electrothermal vaporization (ETV) system using a tungsten boat furnace (TBF) sample cuvette was designed for the direct analysis of solid samples with detection by inductively coupled plasma mass spectrometry (ICP-MS). Into this small sample cuvette, a solid mixture of the biological samples and diammonium hydrogenphosphate powder as a fusion flux was placed and situated on a TBF. Tetramethylammonium hydroxide solution was added to the mixture. After the on-furnace digestion had been completed, the analyte in the cuvette was vaporized and introduced into the ICP mass spectrometer. The solid samples were analyzed by using a calibration curve prepared from the aqueous standard solutions. The detection limit was estimated to be 5.1 pg of lead, which corresponds to 10.2 ng g^–1 of lead in solid samples when a prepared sample amount of 1.0 mg was applied. The relative standard deviation for 8 replicate measurements obtained with 100 pg of lead was calculated to be 6.5%. The analytical results for various biological samples are described.     

Electrothermal vaporization system using furnace-fusion technique for the determination of lead in botanical samples by inductively coupled plasma atomic emission spectrometry

A new approach to sample digestion, subsequent vaporization and introduction into an inductively coupled plasma atomic emission spectrometer was developed for the direct determination of lead. To each small sample cuvette made of tungsten, a mixture of a ground solid sample and powdered diammonium hydrogenphosphate was precisely weighed. The cuvette was positioned onto the tungsten boat furnace (TBF) incorporating a vaporizer. Tetramethylammonium hydroxide solution was added. Then the cuvette was heated and maintained at a wet-digestion temperature to decompose the solid sample. After digestion, the temperature was elevated to generate the analyte vapor for introduction into a plasma. Since the solid samples were wet-digested in the sample cuvettes before vaporization, they could be analyzed by using a calibration curve prepared from aqueous standard solutions. This method was applied to the determination of lead in several biological materials with satisfactory results.     

Electrothermal vaporization system using furnace-fusion technique for the determination of lead in botanical samples by inductively coupled plasma atomic emission spectrometry

A new approach to sample digestion, subsequent vaporization and introduction into an inductively coupled plasma atomic emission spectrometer was developed for the direct determination of lead. To each small sample cuvette made of tungsten, a mixture of a ground solid sample and powdered diammonium hydrogenphosphate was precisely weighed. The cuvette was positioned onto the tungsten boat furnace (TBF) incorporating a vaporizer. Tetramethylammonium hydroxide solution was added. Then the cuvette was heated and maintained at a wet-digestion temperature to decompose the solid sample. After digestion, the temperature was elevated to generate the analyte vapor for introduction into a plasma. Since the solid samples were wet-digested in the sample cuvettes before vaporization, they could be analyzed by using a calibration curve prepared from aqueous standard solutions. This method was applied to the determination of lead in several biological materials with satisfactory results.     

Sensitive determination of bromine and iodine in aqueous and biological samples by electrothermal vaporization inductively coupled plasma mass spectrometry using tetramethylammonium hydroxide as a chemical modifier

A procedure for the simultaneous determination of bromine and iodine by inductively coupled plasma (ICP) mass spectrometry was investigated. In order to prevent the decrease in the ionization efficiencies of bromine and iodine atoms caused by the introduction of water mist, electrothermal vaporization was used for sample introduction into the ICP mass spectrometer. To prevent loss of analytes during the drying process, a small amount of tetramethylammonium hydroxide solution was placed as a chemical modifier into the tungsten boat furnace. After evaporation of the solvent, the analytes instantly vaporized and were then introduced into the ICP ion source to detect the (79)Br(+), (81)Br(+), and (127)I(+) ions. By using this system, detection limits of 0.77 pg and 0.086 pg were achieved for bromine and iodine, respectively. These values correspond to 8.1 pg mL(-1) and 0.91 pg mL(-1) of the aqueous bromide and iodide ion concentrations, respectively, for a sampling volume of 95 microL. The relative standard deviations for eight replicate measurements were 2.2% and 2.8% for 20 pg of bromine and 2 pg of iodine, respectively. Approximately 25 batches were vaporizable per hour. The method was successfully applied to the analysis of various certified reference materials and practical situations as biological and aqueous samples. There is further potential for the simultaneous determination of fluorine and chlorine.     

Determination of Trace Chlorine in Fine Ceramics by ICP-AES Using Tungsten Boat Furnace Vaporizer and Exchangeable Sample Cuvette System as a Direct Solid Sampler

A new approach to simple solid sample digestion, subsequent vaporization, and introduction into an inductively coupled plasma was developed for the direct determination of chlorine in fine ceramic materials by atomic emission spectrometry. To each small sample cuvette made of tungsten, a powder sample was placed and weighed accurately. Following an addition of modifier solution, the cuvette was positioned on the tungsten boat furnace incorporated an electrothermal vaporizer. Then, the analyte in the sample cuvette was vaporized and introduced into the plasma; the major components of ceramic being retained. The solid ceramic samples were analyzed by using an external calibration curve prepared with the aqueous standard solutions. The detection limit of chlorine was estimated to be 0.71 ng, which corresponds to 59 ng g^?1 of the chlorine concentration in solid ceramic materials. The relative standard deviation was calculated to be 3.2%. The analytical results in various ceramic materials are described.     

Generation of a methylbismuth species and its electrothermal vaporization for the determination of bismuth by inductively coupled plasma mass spectrometry

Inorganic bismuth(III) was converted to a methylbismuth species, possibly trimethylbismuth, by a thermochemical reaction with methyllithium. It instantly vaporized and was then introduced into the ICP ion source to detect the 209Bi signal. Utilizing an exchangeable small sample cuvette placed on the tungsten boat furnace for the reaction was very favorable from the viewpoints of easy handling, no memory effect, and maintenance of furnace conditions. In this manner, the analyte was vaporized at quite a low temperature (150 degrees C). The detection limit (3sigma) was 0.13 pg of bismuth and the precision in relative standard deviation for 5.0 pg of bismuth was determined to be 3.8% (n = 7).     

Generation of a methylbismuth species and its electrothermal vaporization for the determination of bismuth by inductively coupled plasma mass spectrometry

Inorganic bismuth(III) was converted to a methylbismuth species, possibly trimethylbismuth, by a thermochemical reaction with methyllithium. It instantly vaporized and was then introduced into the ICP ion source to detect the ²⁰⁹Bi signal. Utilizing an exchangeable small sample cuvette placed on the tungsten boat furnace for the reaction was very favorable from the viewpoints of easy handling, no memory effect, and maintenance of furnace conditions. In this manner, the analyte was vaporized at quite a low temperature (150 °C). The detection limit (3σ) was 0.13 pg of bismuth and the precision in relative standard deviation for 5.0 pg of bismuth was determined to be 3.8% (n = 7). Received: 6 June 1999 / Revised: 31 August 1999 / /Accepted: 23 September 1999     

Electrothermal vaporization for the determination of halogens by reduced pressure inductively coupled plasma mass spectrometry

Trace level quantities of some halogen elements are determined by coupling tungsten filament electrothermal vaporization (ETV) with reduced pressure argon inductively coupled plasma mass spectrometry (ICP-MS). Microliter aqueous samples of chlorides, bromides and iodides were loaded on the tungsten wire, where they were dried at constant current and then vaporized by using a high-capacity condenser discharge. On decreasing the pressure of the plasma, analyte intensity increased sharply. The reduced pressure ICP is seen to give a much narrower, more intense signal profile. The detection limits for bromine and chlorine improved about 10 times compared with an atmospheric pressure ICP ionization source. An electron collision ionization mechanism may contribute most to halogen ionization for reduced pressure ICP. The linear dynamic range was over three orders of magnitude. The precision was generally between 3–8%. Matrix effect was investigated with Na as a matrix element. Absolute detection limits for the elements studied are in the picogram to subnanogram range.     

Determination of cadmium by an improved double chamber electrothermal vaporization inductively coupled plasma atomic emission spectrometry

An improved double chamber electrothermal vaporization (ETV) system was designed. A new inner chamber and its bottom plate made of quartz glass were attached with carrier support gas inlet port for the determination of cadmium by inductively coupled plasma atomic emission spectrometry (ICP-AES). The use of the inner chamber in combination with the plate played important roles to transport the metal vapor efficiently into argon ICP. Ten-μl sample aliquots were dried at 100 °C and subsequently heated at 1000 °C on the tungsten boat furnace. The evolved vapor was swept into the ICP source through PTFE tubing and the inner chamber by a 0.8 l/min H₂ (7%)-Ar carrier gas. The performance parameters of ETV-ICP-AES such as temperature program and gas flow rate were evaluated using cadmium standard solution. Under the optimized experimental conditions, the best attainable detection limit at Cd II 214.438 nm line was 0.2 ng/ml with linear dynamic ranges of 50 to 10,000 ng/ml for cadmium. The instrumental precision expressed as the relative standard deviation (RSD) from ten replicate measurements of 10,000 ng/ml for cadmium by ETV-ICP-AES was 0.85%. The present method has been successfully applied to the determination of cadmium in zinc-base materials.     

电热蒸发进样电感耦合等离子体原子发射光谱（ETV－ICP－AES）联用技术研究

本文采用国产部件组装了一套ＥＴＶ－ＩＣＰ－ＡＥＳ仪器体系，对装置的连接及操作参数进行优化。深入系统地考察了分析物的蒸发过程和传输过程，提出了难熔元素的蒸发和传输机理。研究了ＥＴＶ－ＩＣＰ－ＡＥＳ中基体效应，提出了以聚四氟乙烯为氟化剂，氟化辅助ＥＴＶ－ＩＣＰ－ＡＥＳ测定难熔元素的新方法，应用于环境和生物标样中痕量元素分析，获得满意结果。     

Study on the direct analysis of solid powder biological samples using fluorination assisted electrothermal vaporization inductively coupled plasma atomic emission spectrometry with PTFE slurry modifier

A method has been described for the direct determination of Ti, Cu, Mn, Cr and Cd in solid biological samples without any chemical pretreatment by fluorination assisted electrothermal vaporization inductively coupled plasma atomic emission spectrometry (ETV-ICP-AES) with slurry sampling. A polytetrafluorethylene (PTFE) emulsion was used as a fluorinating reagent to promote the vaporization of the analytes from the graphite furnace. The interface between furnace device and ICP torch and the main factors affecting the analytical signal were investigated systematically. The detection limits for the determination of Ti, Cu, Mn, Cr and Cd are 6.3, 4.7, 10, 13 and 278 ng/mL, respectively; the relative standard deviations are in the range of 1.5 (Mn) ∼4.0% (Cd) after optimization of the operating conditions. The recommended approach has been applied to directly determine the trace elements of interest in the Chinese traditional medicine Loulu and in the solid biological standard reference material (peach leaves, GBW 08501) with satisfactory results. Received: 28 December 1998 / Revised: 9 February 1999 / Accepted: 12 February 1999     

蒸发/氧化法预处理-ICP/AES方法测定油品中的金属元素含量

原油及重油中金属元素含量的分析对于炼油工艺具有非常重要的意义。目前,国内外常用的金属含量的分析方法有等离子体发射光谱法(ICP/AES)和原子吸收光谱(AAS)法,特别是ICP/AES方法,由于可实现多种元素的同时测定,且分析速度快、灵敏度高,故应用最为广泛。无论选用哪种方法,测定     

Transport efficiencies and analytical determinations with electrothermal vaporization employing electrostatic precipitation and electrothermal atomic spectroscopy

Analyte transport efficiencies of solid as well as liquid samples were determined for electrothermal vaporization (ETV). A graphite furnace of the boat-in-tube type was employed for ETV. The generated aerosol was transported by an argon flow via a tubing into an external precipitator and deposited on a L’vov platform with a corona-like discharge. The sample on the secondary platform was analysed with a laboratory-constructed coherent forward scattering multielement spectrometer. For determining the analyte transport efficiencies, the comparative measurements were carried out with standard solutions dosed directly on the platform in the spectrometer furnace. The simultaneously investigated elements were Cu, Fe and Mn in the standard reference material BCR CRM 189 wholemeal flour and in a multielement standard solution containing approximately the same element ratio as certified for the solid sample. ETV boat-to-L’vov platform transport efficiencies of approximately 19% for Cu, 24% for Fe and 19% for Mn were calculated for both solid samples and multielement standard solutions. Cu, Fe and Mn in wholemeal flour were determined simultaneously by calibrating against aqueous multielement standard solutions injected into the boat as well as by the standard addition method. The results agree satisfactorily, the deviations from the certified values are below 10% and the relative standard deviations are typically 5–8%. The limits of detection are 250 pg for Cu (λ=324.8 nm), 230 pg for Fe (λ=248.3 nm) and 90 pg for Mn (λ=279.8 nm), loaded into the ETV boat.     

Study on the direct analysis of solid powder biological samples using fluorination assisted electrothermal vaporization inductively coupled plasma atomic emission spectrometry with PTFE slurry modifier

A method has been described for the direct determination of Ti, Cu, Mn, Cr and Cd in solid biological samples without any chemical pretreatment by fluorination assisted electrothermal vaporization inductively coupled plasma atomic emission spectrometry (ETV-ICP-AES) with slurry sampling. A polytetrafluorethylene (PTFE) emulsion was used as a fluorinating reagent to promote the vaporization of the analytes from the graphite furnace. The interface between furnace device and ICP torch and the main factors affecting the analytical signal were investigated systematically. The detection limits for the determination of Ti, Cu, Mn, Cr and Cd are 6.3, 4.7, 10, 13 and 278 ng/mL, respectively; the relative standard deviations are in the range of 1.5 (Mn) ∼4.0% (Cd) after optimization of the operating conditions. The recommended approach has been applied to directly determine the trace elements of interest in the Chinese traditional medicine Loulu and in the solid biological standard reference material (peach leaves, GBW 08501) with satisfactory results. Received: 28 December 1998 / Revised: 9 February 1999 / Accepted: 12 February 1999     

Signal enhancement effect of halogen matrix in electrothermal vaporization-inductively coupled plasma-mass spectrometry

In tungsten furnace electrothermal vaporization(ETV)-inductively coupled plasma mass spectrometry(ICP-MS), the presence of halogen matrices caused a signal enhancement for volatile elements such as Zn, Cd and Pb, whose halides melting and boiling points were relatively low. In order to clarify the mechanism of signal enhancement in ETV-ICP-MS, the effects of chemical interaction between analytes and halogen matrices on the surface of ETV furnace, the transport efficiency of vaporized analytes from the furnace into the ICP and the physical properties of the ICP itself and of the micro plasma (interface plasma) in the interface region between the sampling and the skimmer cones were investigated by atomic absorption and atomic emission spectrometry. Among the effects mentioned above, neither the chemical interaction on the surface of the ETV furnace nor the transport efficiency of vaporized analytes could be related to the analyte signal enhancements. The degree of enhancement was found to depend on the ionization potential of the coexisting halogen and was not caused by a variation in the physical properties of the ICP but rather by a variation of those of the interface plasma. These results suggest that the halogen matrices may affect the physical properties of the interface plasma, contributing to the promotion of the ionization of analytes.     

Determination of vanadium and titanium in steel by inductively coupled plasma atomic emission spectrometry with modified use of a tungsten boat furnace atomizer for atomic absorption spectrometry

For electrothermal sample introduction, a commercially available tungsten boat atomizer for atomic absorption spectrometry (AAS) was transferred to a vaporizer for inductively coupled plasma atomic emission spectrometry (ICP-AES). The modification retained as much of the original design of the atomizer as possible, so that the apparatus could be switched easily between conventional tungsten boat furnace (TBF)-AAS and TBF-ICP-AES. By using this system, a procedure for the determination of vanadium and titanium in steel was investigated. The detection limits (S/N=3) of vanadium and titanium were 3.9 and 1.5 ng ml^?1, respectively. The relative standard deviations for five replicate determinations were ca. 3% for both elements. The calibration graphs were linear up to 100 μg ml^?1 vanadium(V) and 10 μg ml^?1 titanium(IV). Results of analyses of some low-alloy steel samples are given.     

High-resolution continuum source electrothermal absorption spectrometry of AlBr and CaBr for the determination of bromine

Molecular absorption spectra of AlBr and CaBr, produced in a graphite furnace, were investigated using a high-resolution echelle spectrometer equipped with a xenon short-arc lamp as continuum source. The analytical usability of the spectra for the determination of bromine was studied. To this end, the molecular absorptions of AlBr at 278.914 nm and CaBr at 625.315 nm were evaluated. Apart from strong absorption bands of CaF around 625.3 nm, which disturb the use of CaBr, no spectral interferences were observed for both AlBr and CaBr. Regarding chemical interference with matrix substances, the molecular absorption of AlBr and CaBr is influenced in a different way. While the sensitivity of the CaBr absorption is susceptible to chloride, aluminum, potassium and sodium ions, there is no significant effect on the AlBr absorption. In contrast, the inorganic acids (nitric, phosphoric, and sulfuric) have an influence on AlBr, but not on the CaBr molecular absorption. Therefore, the two methods complement each other and each has its own application area. Regarding real samples, a salt sample from the death sea and an organic pharmaceutical were evaluated. The results were in good agreement with those derived from two independent methods and with an existing reference value. Relative standard deviations were found in the range of 5%. The limit of detection for bromine was about 2 ng for both AlBr and CaBr molecular absorption; the dynamic range was linear at least up to 250 ng Br.