Preparation of diatomite–TiO<Subscript>2</Subscript> composite for photodegradation of bisphenol-A in water

To enhance the photodegradation performance of pure titanium dioxide (TiO₂), diatomite was used as a porous carrier to immobilize TiO₂ powders using calcination method. The photodegradation of bisphenol-A (BPA; 4,4′-isopropylidenediphenol), which has been listed as one of endocrine disrupting chemicals, was carried out in a batch suspension reactor using pure TiO₂ powders and diatomite–TiO₂ composites, respectively. Under the controlled conditions, the photocatalytic efficiencies of the BPA degradation by the diatomite–TiO₂ composites can be found to be higher than those by pure TiO₂ powders. This result should be attributable to the accessibility of the BPA molecules to the surface of TiO₂ particle in the modified photocatalysts, showing that the enrichment of the organic solute enhanced the rate of photodegradation on the diatomite–TiO₂ composite. However, the photodegradation efficiency was not dependent on the pore properties of these TiO₂ photocatalysts. The experimental results further indicated that the photodegradation kinetics for the destruction of BPA in water followed the first-order model well. The apparent first-order reaction constants (k _obs), thus obtained from the fittings of the model, were in line with the destruction-removal efficiencies of BPA in all the photocatalytic experiments.     

Mechanochemical Activation of Cu–CeO<Subscript>2</Subscript> Mixture as a Promising Technique for the Solid-State Synthesis of Catalysts for the Selective Oxidation of CO in the Presence of H<Subscript>2</Subscript>

A new ecologically clean method for the solid-phase synthesis of oxide copper–ceria catalysts with the use of the mechanochemical activation of a mixture of Cu powder (8 wt %) with CeO₂ was developed. It was established that metallic copper was oxidized by oxygen from CeO₂ in the course of mechanochemical activation. The intensity of a signal due to metallic Cu in the X-ray diffraction analysis spectra decreased with the duration of mechanochemical activation. The Cu¹⁺, Cu²⁺, and Ce³⁺ ions were detected on the sample surface by X-ray photoelectron spectroscopy. The application of temperature-programmed reduction (TPR) made it possible to detect two active oxygen species in the reaction of CO oxidation in the regions of 190 and 210–220°C by a TPR-H₂ method and in the regions of 150 and 180–190°C by a TPR-CO method. It is likely that the former species occurred in the catalytically active nanocomposite surface structures containing Cu–O–Ce bonds, whereas the latter occurred in the finely dispersed particles of CuO on the surface of CeO₂. The maximum conversion of CO (98%, 165°C) reached by the mechanochemical activation of the sample for 60 min was almost the same as conversion on a supported CuO/CeO₂ catalyst.     

Theoretical study of reaction mechanism for Se + O<Subscript>3</Subscript>

The reaction mechanism of Se + O₃ on the singlet potential energy has been investigated at CCSD(T)/6-311++G(2df,2pd) level of theory based on the geometric parameters optimized at the B3LYP/6-311++G(3df,3pd) level of theory. The calculated results show that the reactants are firstly associated into the adduct Se–O₃ with any intrinsic barrier. Subsequently, through a variety of transformations of isomer Se–O₃, two kinds of products P₁(SeO₃(D_3h)) and P₂(SeO + ³O₂) are obtained. The breakage and formation of the chemical bonds in the reaction have been studied by the topological analysis of electronic density. The topological analysis results show that the ring transitional structure region does not only occur in cis-OSeOO → SeO₃(C_s) process but also occur in SeO₃(C_s) → SeO₃(D_3h).     

Separation of phosphorous by liquid–liquid extraction for the measurement of <Superscript>32</Superscript>P

Phosphorous containing radioisotope waste was separated and determined by liquid–liquid extraction method through liquid scintillation counter (LSC). In this process, ammonium phosphate was converted to phosphomolybdate (PMo) by the reaction of ammonium molybdate (Mo) in HCl solution (0.02 M) and maximum UV/VIS absorbance (λ_max) 218 nm was observed. The PMo solution was extracted with TOA (Tri-n-Octylamine)/xylene mixture and λ_max 290 nm was found for this organic layer. Absorbance of aqueous and organic layer was linear through concentration. The impurities such as Co, Cr, Gd, etc. remain in aqueous layer by treating with Mo which was determined by ICP-AES and AAS. The quenching correction curve for ³²P was calculated using LSC results. No counting change was observed as the volume of quenchers increased. The recovery was 98% and 81% for the extraction and separation process from the test using H₃³²PO₄ as standard tracer.     

An aptameric molecular beacon-based “Signal-on” approach for rapid determination of rHuEPO-α

The aim of this work is to describe the first example of aptameric molecular beacon (MB)-based probe for the detection of recombinant human erythropoietin (rHuEPO-α) in physiological buffer, using a novel 35 nt ssDNA aptamer (807-35 nt) originally isolated by Systematic Evolution of Ligands by Exponential enrichment (SELEX) technique in our laboratory. Both “Signal-on” and “Signal-off” MB modes were developed, respectively, in which the conformational alteration of aptamer before and after binding to rHuEPO-α can be demonstrated in terms of the correspondingly fluorescent changes. Comparing with “Signal-off” mode, “Signal-on” mode provided higher sensitivity, while with the addition of target rHuEPO-α, quenching between fluorescent 807-35 nt aptamer (F-Apt) and a short quencher-labeled complementary sequence (QDNA) was disturbed by the specific binding between rHuEPO-α and F-Apt. QDNA was thus loosened and released from F-Apt, leading to a consequently full fluorescent restoration. Systematic optimization of parameters in “Signal-on” mode were carried out, the choice of QDNA length, the hybridization site of a small supplementary DNA (SDNA) stabilizer, and the existence of Mg²⁺ cation played essential roles for the performance characterization. A convenient and sensitive determination of rHuEPO-α with a LOD of 0.4 nM was achieved.     

Synthesis of 2,2′-Biindolyls; Potential Intermediates for Indolocarbazole Alkaloids

The synthesis of 2,2′-biindolyls oxygenated in the benzenoid ring is reported. Wittig-Horner reaction of the phosphonate esters of 1-benzenesulfonyl-2- bromomethyl-3-substituted indoles with o-nitrobenzaldehydes followed by deoxygenation with triethyl phosphite gave 2,2′-biindolyls.     

Preparation of SiO<Subscript>2</Subscript>–ZrO<Subscript>2</Subscript> xerogel and its application for the removal of organic dye

SiO₂–ZrO₂ xerogel was prepared via a sol–gel method followed by ambient pressure drying. The xerogel was characterized by X-ray diffraction, thermal analysis, fourier transform infrared spectroscopy, scanning electron microscopy, and nitrogen adsorption/desorption analysis. The results showed that the SiO₂–ZrO₂ xerogel was amorphous and possessed a three-dimensional network structure with a narrow distribution of pore size. Its specific surface area reached up to 525.6?m²/g after 600?°C heat treatment, with a pore volume of 1.16?cm³/g and an average pore size of 8.5?nm. In order to explore the potential application of the SiO₂–ZrO₂ xerogel for the removal of organic dyes, its adsorption capacity was studied by removal of Rhodamine B (RhB) from aqueous solution through batch experiments. The results showed that the adsorption process of RhB onto SiO₂–ZrO₂ xerogel was slightly promoted under acidic conditions and significantly inhibited under strong alkaline conditions. And adsorption equilibrium can be achieved in 30?min. The kinetic data of the adsorption were analyzed using pseudo-first-order and pseudo-second-order models. The results indicated that the pseudo-second-order model described the adsorption mechanism better. The sorption behavior was evaluated by Langmuir and Freundlich isotherm models. The results suggested that the Langmuir model could accurately describe the experimental data and the adsorption capacity q_max was 177.7?mg/g. Thermodynamic analysis revealed that the adsorption of RhB onto the SiO₂–ZrO₂ xerogel was both spontaneous and exothermic in nature. Thus, the as-prepared SiO₂–ZrO₂ xerogel might be used as an adsorbent for wastewater treatment, especially for the removal of dyes.

Open image in new window

     

Synthesis of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@PPy–MWCNT nanocomposite and its application for extraction of ultra-trace amounts of PAHs from various samples

In the present study, multi-walled carbon nanotube oxide was immobilized on the pyrrole magnetic nanoparticles. Application of the synthesized material was investigated for the magnetic solid-phase extraction (MSPE) of polycyclic aromatic hydrocarbons (PAHs), from the environmental samples. Determinations of the analytes were performed with gas chromatography–mass spectrometry. The structure and morphology of Fe₃O₄@PPy–MWCNT were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, thermal gravimetric analysis, and vibrating sample magnetometer. Performance of MSPE is mainly affected by extraction time, sorbent amount, sample solution volume, and eluent type and volume. In this study, the best possible performance of MSPE has been achieved using a combination of central composite design and Bayesian regularized artificial neural network technique. Under the optimum extraction conditions, linear range between 0.5 and 250 µg L^?1 (R ² > 0.994), preconcentration factors from 232 to 403 and limits of detection ranging from 0.1 to 0.3 µg L^?1 were obtained. Relative standard deviations for intra-day and inter-day precision were 3.3–5.1% and 3.7–5.6%, respectively. In addition, feasibility of the method was demonstrated by extraction and determination of PAHs from some real samples containing tap water, hookah water as well as soil samples, and relative recovery in the range of 85.4–106.8% was obtained. This MSPE method provides several advantages, such as high extraction efficiency, minimum sorbent for extraction of the analytes from high sample volumes, convenient extraction procedure, and short analysis times.     

Synthesis of TCPP–Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@S/RGO and its application for purification of water

A one-step green-chemistry method was applied to prepare sulfur/reduced graphene oxide (S/RGO). The synthesized S/RGO was modified by 5,10,15,20-tetrakis(4-carboxyphenyl)porphyrin (TCPP) and Fe₃O₄ nanoparticles to form TCPP–Fe₃O₄@S/RGO. The prepared composites were investigated by X-ray diffraction (XRD) analysis, Fourier-transform infrared (FT-IR) spectroscopy, X-ray photoelectron spectroscopy (XPS), energy-dispersive X-ray (EDX) mapping, and transmission electron microscopy (TEM) and scanning electron microscopy (SEM) imaging. Diffuse reflectance spectroscopy (DRS) was used to determine the photocatalytic ability of S/RGO and TCPP–Fe₃O₄@S/RGO. In addition, photocatalytic degradation of a hazardous dye (methylene blue) by the TCPP–Fe₃O₄@S/RGO composite under visible-light irradiation is reported. The results demonstrate synthesis of TCPP–Fe₃O₄@S/RGO by an environmentally friendly method with excellent degradation effect.     

The Biosynthesis of Barbamide—A Radical Pathway for “Biohalogenation”?

A stereoselective chlorination of a methyl group and the preference of cleavage of nonactivated primary C−H bonds in one of the methyl groups with respect to a weaker tertiary C−H bond in the course of the biosynthesis of barbamide point to a surprising, new mechanism of “biohalogenation” (see schematic diagram).     

Use of integrated intensities of X-ray powder diffraction patterns of Mg<Subscript>1 − x</Subscript>Zn<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>O solid solutions for the quantitative determination of their composition

X-ray diffraction spectra were obtained for polycrystalline samples of Mg_{1 ? x} Zn _x O solid solutions (x = 0.3, 0.5, 0.6, and 0.7) by X-ray powder diffraction. The theoretical integrated intensity ratio between the 111 and 002 reflections was plotted versus the percentage of zinc in the solid solutions. The possibility of extracting information on polycrystalline samples (the composition and the presence of microstructural features) from comparison of the theoretical and experimental integrated intensity ratios between the 111 and 002 reflections was investigated. The Le Bail procedure for the extraction of integrated intensities from X-ray powder diffraction patterns, followed by the use of these intensities in calculations with the SHELX-97 program package, was tested for the determination of the zinc fraction in polycrystalline samples of Mg_{1 ? x} Zn _x O solid solutions.     

Study of the effect of methods for liquid-phase synthesis of nanopowders on the structure and physicochemical properties of ceramics in the CeO<Subscript>2</Subscript>–Y<Subscript>2</Subscript>O<Subscript>3</Subscript> system

Two alternative chemical synthesis methods—cryotechnological coprecipitation of hydroxides and cocrystallization of salts—were used for preparing (CeO₂)_1–x (Y₂O₃) _x nanopowders (x = 0.10, 0.15, 0.20) with a mean coherent scattering domain size of ~7–11 nm and S _sp = 2.1–97.5 m²/g. From these nanopowders, ceramic nanomaterials with mean coherent scattering domain sizes of ~61–85 nm were synthesized. It was studied how the phase composition, microstructure, and electrical transport properties of the produced samples depend on the Y₂O₃ content of a CeO₂-based solid solution and on the synthesis method. It was shown that, in the series (CeO₂)_1–x (Y₂O₃) _x (x = 0.10, 0.15, 0.20), the solid solution (CeO₂)_0.90(Y₂O₃)_0.10 has the highest ionic conductivity with the ion transport number t _i = 0.73 (600°C). In its physicochemical characteristics, this ceramic can be used as a solid electrolyte of intermediate-temperature fuel cells.     

Graphic model for calculating the entropy of С<Subscript>11</Subscript>Н<Subscript>24</Subscript> alkanes with allowance for multiple non-valence interactions through three atoms along the chain of a molecule

A fourteen-constant graphic scheme is proposed for evaluating the thermodynamic properties of branched paraffin hydrocarbons. Absolute entropy S_{f, 298 gas} of 159 alkanes, of which 157 alkanes have yet to be studied experimentally, are calculated using 105 experimental data S_{f, 298 K, gas} for alkanes CН₄–С₃₂Н₆₆.     

Thermal properties of Nafion–TiO<Subscript>2</Subscript> composite electrolytes for PEM fuel cell

Thermal analysis has been used to evaluate the stability, glass transition, and water retention of Nafion based polymer–ceramic electrolytes. These electrolytes are envisioned as promising replacement of Nafion in fuel cells operating above 100 °C. The polymeric matrix prepared by casting exhibits lower crystallinity than the extruded Nafion, a feature that affects the water absorption properties. The addition of titania-based nanotubes and nanoparticles to the polymer has enhanced the water retention at high temperatures (~130 °C) and the glass transition temperature, respectively. Such results are important for the design of composite electrolytes for the operation of fuel cells at high temperatures.     

Palladium-catalyzed cross-coupling of α-bromocarbonyls and allylic alcohols for the synthesis of α-aryl dicarbonyl compounds

The palladium-catalyzed coupling of olefins and organohalides is a versatile approach for synthesizing complex molecules from simple starting materials. We have developed a palladium-catalyzed coupling of α-bromocarbonyl compounds with allylic alcohols for the generation of acyclic aryl-substituted dicarbonyl compounds. The reaction proceeds via a tandem olefin insertion of an α-acyl radical followed by a 1,2-aryl migration. In addition to providing preliminary evidence for a free radical mediated mechanism, we demonstrate unprecedented levels of 1,3-stereoinduction for the 1,2-migration step.     

p<Emphasis Type="Italic">K</Emphasis><Subscript>a</Subscript> measurements for the SAMPL6 prediction challenge for a set of kinase inhibitor-like fragments

Determining the net charge and protonation states populated by a small molecule in an environment of interest or the cost of altering those protonation states upon transfer to another environment is a prerequisite for predicting its physicochemical and pharmaceutical properties. The environment of interest can be aqueous, an organic solvent, a protein binding site, or a lipid bilayer. Predicting the protonation state of a small molecule is essential to predicting its interactions with biological macromolecules using computational models. Incorrectly modeling the dominant protonation state, shifts in dominant protonation state, or the population of significant mixtures of protonation states can lead to large modeling errors that degrade the accuracy of physical modeling. Low accuracy hinders the use of physical modeling approaches for molecular design. For small molecules, the acid dissociation constant (pK_a) is the primary quantity needed to determine the ionic states populated by a molecule in an aqueous solution at a given pH. As a part of SAMPL6 community challenge, we organized a blind pK_a prediction component to assess the accuracy with which contemporary pK_a prediction methods can predict this quantity, with the ultimate aim of assessing the expected impact on modeling errors this would induce. While a multitude of approaches for predicting pK_a values currently exist, predicting the pK_as of drug-like molecules can be difficult due to challenging properties such as multiple titratable sites, heterocycles, and tautomerization. For this challenge, we focused on set of 24 small molecules selected to resemble selective kinase inhibitors—an important class of therapeutics replete with titratable moieties. Using a Sirius T3 instrument that performs automated acid–base titrations, we used UV absorbance-based pK_a measurements to construct a high-quality experimental reference dataset of macroscopic pK_as for the evaluation of computational pK_a prediction methodologies that was utilized in the SAMPL6 pK_a challenge. For several compounds in which the microscopic protonation states associated with macroscopic pK_as were ambiguous, we performed follow-up NMR experiments to disambiguate the microstates involved in the transition. This dataset provides a useful standard benchmark dataset for the evaluation of pK_a prediction methodologies on kinase inhibitor-like compounds.     

Bimetallic Co–Ni/TiO<Subscript>2</Subscript> catalysts for selective hydrogenation of cinnamaldehyde

Bimetallic Co–Ni catalysts in the composition range Co_(1?x)Ni_x with x?=?0.0, 0.2, 0.3, 0.4, 0.5, 0.6, 0.8 and 1.0, with total metal loading of 15% w/w and supported on TiO₂-P25, have been prepared by chemical reduction of the metal acetates by glucose in aqueous alkaline medium and characterized by XRD, TEM, TPR, XPS and H₂-TPD techniques. Selective hydrogenation of cinnamaldhyde (CAL) to hydrocinnamaldehyde (HCAL), cinnamyl alcohol (COL) and hydrocinnamyl alcohol (HCOL) has been investigated at 20 bar pressure, in the temperature range 120–140 °C. Co/Ni crystallite sizes in the range 6.0?±?1 nm are observed by TEM. TPR and XPS results indicate the formation of nanoscale Co–Ni alloys, which tend to weaken M–H bond strength, as revealed by H₂-TPD measurements. Ni/TiO₂ displays very high conversion of CAL (86.9%) with high selectivity (78.7%) towards HCAL formation at 140 °C. Co/TiO₂, on the other hand, exhibits relatively lower CAL conversion (55%) and higher selectivity (61.3%) for COL formation at the same temperature. However, bi-metallic Co–Ni catalysts in the composition range x?=?0.3–0.6 display very high conversion (>?98%) due to alloy formation and weakening of M–H bonds. Bimetallic Co_0.7Ni_0.3 catalyst displays high conversion of CAL (98.1%) and high selectivity (82.9%) towards HCOL. Overall CAL hydrogenation activity at 140 °C, when expressed as TOF, displays a maximum value at the composition Co_0.5Ni_0.5. Activity and selectivity patterns have been rationalized based on the reaction pathways observed on the catalysts and the influence of Co–Ni alloy formation and M–H bond strength. Thus, a synergetic effect, originating from an appropriate composition of base metal catalysts and reaction conditions, could result in hydrogenation activity comparable with noble metal based catalysts.     

Effect of potassium addition on bimetallic PtSn/θ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst for dehydrogenation of propane to propylene

PtSn/θ-Al₂O₃ catalysts with different amounts of K (0.14, 0.22, 0.49, 0.72, and 0.96 wt%) are prepared to investigate the K effects on the PtSn catalyst in propane dehydrogenation (PDH). KPtSn catalyst with 0.xx wt% K, 0.5 wt% Pt and 0.75 wt% Sn is designated as xx-KPtSn. PDH was performed at 873 K and a gas hourly space velocity (GHSV) of 53,000 mL/g_cat h. The temperature-programmed desorption (NH₃-TPD), temperature-programmed reduction (TPR) and CO chemisorption of the KPtSn catalysts with K added revealed the potassium addition blocked the acid sites, promoted the reduction of Sn oxide and decreased the Pt dispersion. The formations of cracking products and higher hydrocarbons on acid sites were suppressed by the K effect of blocking the acid sites. In contrast, K addition at more than 0.72 wt% rather increased cracking products and the amount of coke, resulting in the severe deactivation of catalysts. The high cracking products on the KPtSn catalysts with the high amount of K should not be related to the acid sites, because the acid sites were monotonously decreased with an increase in the amount of K. Instead, the potassium affected the characteristics of PtSn. The interaction between Pt and Sn could be weakened by enriching the reduced Sn, because the K component promoted the reduction of Sn oxide in the TPR experiments. Therefore, the 14-KPtSn catalyst with the low amount of K exhibits the highest stability and selectivity among the prepared KPtSn catalysts due to the compromise of the advantageous (blocking the acid sites) and bad (weakening the interaction between Pt and Sn) effects of the K addition in PDH.     

Synthesis and characterization of Pd nanoparticle-modified magnetic Sm<Subscript>2</Subscript>O<Subscript>3</Subscript>–ZrO<Subscript>2</Subscript> as effective multifunctional catalyst for reduction of 2-nitrophenol and degradation of organic dyes

In this study, Pd nanoparticle-modified magnetic Sm₂O₃–ZrO₂ material (Pd–Fe₃O₄–Sm₂O₃–ZrO₂) as multifunctional catalyst was fabricated and used for catalytic reduction of 2-nitrophenol compound, degradation of methylene blue and rhodamine B dyes, which are toxic pollutants. The magnetic material was used for the first time as a catalyst for the reduction and degradation studies. Pd nanoparticle-modified magnetic Sm₂O₃–ZrO₂ catalyst was prepared using the deposition–precipitation methods and were characterized by X-ray diffraction, scanning electron microscopy, atomic absorption spectrometry, Raman spectroscopy and BET surface analyzer. The Pd nanoparticle-modified magnetic Sm₂O₃–ZrO₂ material can lead to high catalytic activity for the reduction of 2-nitrophenol and degradation of rhodamine B and methylene blue with >?95% conversion within ~?2 and 80 s even when the content of Pd in it is as low as 5.8 wt%.     

cis‐Peptide Bonds: A Key for Intestinal Permeability of Peptides?

Recent structural studies on libraries of cyclic hexapeptides led to the identification of common backbone conformations that may be instrumental to the oral availability of peptides. Furthermore, the observation of differential Caco‐2 permeabilities of enantiomeric pairs of some of these peptides strongly supports the concept of conformational specificity driven uptake and also suggests a pivotal role of carrier‐mediated pathways for peptide transport, especially for scaffolds of polar nature. This work presents investigations on the Caco‐2 and PAMPA permeability profiles of 13 selected N‐methylated cyclic pentaalanine peptides derived from the basic cyclo(‐D ‐Ala‐Ala₄‐) template. These molecules generally showed moderate to low transport in intestinal epithelia with a few of them exhibiting a Caco‐2 permeability equal to or slightly higher than that of mannitol, a marker for paracellular permeability. We identified that the majority of the permeable cyclic penta‐ and hexapeptides possess an N‐methylated cis‐peptide bond, a structural feature that is also present in the orally available peptides cyclosporine A and the tri‐N‐methylated analogue of the Veber–Hirschmann peptide. Based on these observations it appears that the presence of N‐methylated cis‐peptide bonds at certain locations may promote the intestinal permeability of peptides through a suitable conformational preorganization.