Bis(β‐enaminoketonato) vanadium (III or IV) complexes as catalysts for olefin polymerization

Bis(β‐enaminoketonato) vanadium(III) complexes ( 2a–c ) [O(R₁)C?C(H)_xC(R₂)?NC₆H₅]₂VCl(THF) and the corresponding vanadium(IV) complexes ( 3a–c ) [O(R₁)C?C(H)_xC(R₂)? NC₆H₅]₂VO (R₁ = ? (CH₂)₄? , R₂ = H, x = 0, a ; R₁ = ? C₆H₅, R₂ = H, x = 1, b ; R₁ = ? C₆H₅, R₂ = ? C₆H₅, x = 1, c ) have been synthesized from VCl₃(THF)₃ and VOCl₂(THF)₂, respectively, by treating with 2.0 equivalent β‐enaminoketonato ligands in tetrahydrofuran. Structures of 2b and 3a–c were further confirmed by X‐ray crystallographic analysis. The complexes were investigated as the catalysts for ethylene polymerization in the presence of Et₂AlCl. Complexes 2a–c and 3a–c exhibited high catalytic activities (up to 23.76 kg of PE/mmol_V h bar), and afforded polymers with unimodal molecular weight distributions at 70 °C indicating the good thermal stability. The catalytic behaviors were influenced not only by the oxidation state of the catalyst precursors but also by the ligand structures. Complexes 2a–c and 3a–c were also effective catalyst precursors for ethylene/1‐hexene copolymerization. The influence of polymerization parameters such as reaction temperature, Al/V molar ratio and hexene feed concentration on the ethylene/hexene copolymerization behaviors have bee also investigated in detail. In addition, the agents such as AlMe₃, AlⁱBu₃, MeMgBr, MgCl₂, and ZnEt₂ were applied to control the molecular weight and molecular weight distribution modal. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3062–3072, 2010     

Copolymerization of norbornene with ω‐alkenylaluminum as a precursor comonomer for introduction of carbonyl moieties

Norbornene copolymers functionalized with methyl ester group or carboxy group are facilely synthesized by the copolymerization of norbornene and 7‐octenyldiisobutylaluminum (ODIBA) with ansa‐dimethylsilylene(fluorenyl)(t‐butylamido)dimethyltitanium ( 1 ) activated by Ph₃CB(C₆F₅)₄, and the sequential CO₂/methanolysis reactions or CO₂/hydrolysis reactions, respectively. The methanolysis and the hydrolysis are simply switched by engaging acidic methanol or acidic aqueous acetone as the quenching/washing solution, respectively. Meanwhile, the increase of ODIBA in the copolymerization abruptly decreases the yield and number–average molecular weight (M_n) of the product. However, the addition of triisobutylaluminum (8 mM) and the use of excess Ph₃CB(C₆F₅)₄ (twofold of 0.4 mM of 1 ) significantly increase the yield, accompanying the increase in the M_n and the narrowing of the molecular weight distribution (M_w/M_n), especially in the case of the use of excess Ph₃CB(C₆F₅)₄. The yield (g polymer/g monomers), M_n, and M_w/M_n reach up to 0.82, 341,000, and 1.46, respectively, at a copolymerization condition. The carboxy groups in the norbornene copolymers are controlled in the range of 0–1.8 mol % in high polymer yields with high M_n and narrow M_w/M_n accompanied by the decrease in the contact angle with water from 104° to 89°. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5085–5090     

Synthesis,structural characterization,and olefin polymerization behavior of vanadium(III) complexes bearing bidentate phenoxy‐phosphine ligands

Vanadium(III) complexes bearing phenoxy‐phosphine ligands ( 2a–g ) (2‐R₁‐4‐R₂‐6‐PPh₂‐C₆H₂O)VCl₂(THF)₂ ( 2a : R₁ = R₂ = H; 2b : R₁ = F, R₂ = H; 2c : R₁ = Ph, R₂ = H; 2d : R₁ = tBu, R₂ = H; 2e : R₁ = R₂ = Me; 2f : R₁ = R₂ = tBu; 2g : R₁ = R₂ = CMe₂Ph) were prepared from VCl₃(THF)₃ by treating with 1.0 equiv of the ligand in tetrahydrofuran (THF) in the presence of excess triethylamine (TEA). The reaction of VCl₃(THF)₃ with 2.0 equiv of the ligand in THF in the presence of excess TEA afforded vanadium(III) complexes bearing two phenoxy‐phosphine ligands ( 3c–f ). These complexes were characterized by FTIR and mass spectrum as well as elemental analyses. Structures of 2f and 3c were further confirmed by X‐ray crystallographic analyses. Complexes 2a–g and 3c–f were employed as the catalysts for ethylene polymerization under various reaction conditions. On activation with Et₂AlCl, these complexes exhibited high catalytic activities (up to 41.3 kg PE/mmol_V·h·bar) even at high temperature (70°C), and produced high molecular weight polymer with unimodal molecular weight distributions, indicating the polymerization took place in a single‐site nature. Complexes 3c–f displayed better thermal stability than the corresponding complexes 2a–g under similar conditions. In addition, copolymerizations of ethylene and 1‐hexene with precatalysts 2a–g were also explored in the presence of Et₂AlCl. Catalytic activity, comonomer incorporation, and properties of the resultant polymers can be controlled over a wide range by tuning catalyst structures and reaction parameters.© 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Ethylene polymerization by the new chromium catalysts based on amino‐pyrrolide ligands

A series of amino‐pyrrolide ligands ( 1–4a ) and their derivatives amino‐thiophene ligand ( 5a ), amino‐indole ligand ( 6a ) were prepared. Chromium catalysts, which were generated in situ by mixing the ligands with CrCl₃(thf)₃ in toluene, were tested for ethylene polymerization. The preliminary screening results revealed that the tridentate amino‐pyrrolide ligands containing soft pendant donor, 3a, 4a /CrCl₃(thf)₃ systems displayed high catalytic activities towards ethylene polymerization in the presence of modified methyaluminoxane. The electronic and steric factors attached to the ligand backbone significantly affected both the catalyst activity and the polymer molecular weight. Complex 4b was obtained by the reaction of CrCl₃(thf)₃ with one equivalent of the lithium salts of 4a , which was the most efficient ligand among the tested ones. The effect of polymerization parameters such as cocatalyst concentration, ethylene pressure, reaction temperature, and time on polymerization behavior were investigated in detail. The resulting polymer obtained by 4b display wax‐like and possess linear structure, low molecular weight, and unimodal distribution. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 713–721, 2009     

Preparation of novel cyclic olefin copolymer with high glass transition temperature

A series of novel cyclic olefin copolymers (COCs), including ethylene/tricyclo[4.3.0.1^2,5]deca‐3‐ene (TDE), ethylene/tricyclo[4.4.0.1^2,5]undec‐3‐ene (TUE), and ethylene/tricyclo[6.4.0.1^9,12]tridec‐10‐ene (TTE) copolymers, have been synthesized via effective copolymerizations of ethylene with bulk cyclic olefin comonomers using bis(β‐enaminoketonato) titanium catalysts ( 1a [PhN?C(CH₃)CHC(CF₃)O]₂TiCl₂; 1b : [PhN?C(CF₃)CHC(Ph)O]₂TiCl₂). With modified methylaluminoxane as a cocatalyst, both catalysts exhibit high catalytic activities, producing high molecular weight copolymers with high comonomer incorporations and unimodal molecular weight distributions. The microstructures of obtained ethylene/COCs are established by combination of ¹H, ¹³C NMR, ¹³C DEPT, HSQC ¹H? ¹³C, and ¹H? ¹H COSY NMR spectra. DSC analyses indicate that the glass transition temperature (T_g) increases with the enhancement of comonomer volume (TDE < TUE < TTE). High T_g value up to 180 °C is easily attained in ethylene/TTE copolymer with the low content of 35.8 mol %. TGA analyses reveal that these copolymers all possess high thermal stability with degradation temperatures (T_d) higher than 370 °C in N₂ and air. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3144–3152     

Ethylene polymerization by the chromium catalysts based on bidentate [O,PO] or [S,P] ligands

Novel chromium catalysts based on bidentate phenoxy‐phosphinoyl (HO‐2R₁‐4R₂‐6(Ph₂P?O)C₆H₂: R₁ = R₂ = H, 3a ; R₁ = tBu, R₂ = H, 3b ; R₁ = R₂ = tBu, 3c ; R₁ = R₂ = cumyl, 3d ; R₁ = anthracenyl, R₂ = H, 3e ) and thiophenol‐phosphine (HS‐2R₁‐4R₂‐6(Ph₂P)C₆H₂: R₁ = R₂ = H, 4a ; R₁ = SiMe₃, R₂ = H, 4b ) were prepared and characterized. Treatment with modified methyaluminoxane, these catalysts displayed moderate to high‐catalytic activities for ethylene polymerization. The activities of them were higher than those of the corresponding catalysts based on bidentate phenoxy‐phosphine ligands. Both the coordinated donors and the ortho‐substituent of the ligands played an important role in improving catalytic activity. The effects of reaction parameters, such as cocatalyst and Al/Cr molar ratio as well as reaction temperature, on ethylene polymerization behaviors were investigated in detail for two favorable catalytic systems, 3b /CrCl₃(thf)₃ and 4b /CrCl₃(thf)₃. Catalyst 4b /CrCl₃(thf)₃ displayed higher catalytic activity and better temperature tolerance for ethylene polymerization than 3b /CrCl₃(thf)₃. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 311–319, 2010     

Novel vanadium(III) complexes with tridentate phenoxy‐phosphine [O,P(O),O] ligands: Synthesis,characterization, and catalytic behavior of ethylene polymerization and copolymerization with 10‐undecen‐1‐ol

A series of novel vanadium(III) complexes bearing tridentate phenoxy‐phosphine [O,P,O] ligands and phosphine oxide‐bridged bisphenolato [O,P?O,O] ligands, which differ in the steric and electronic properties, have been synthesized and characterized. These complexes were characterized by Fourier transform infrared spectroscopy (FTIR) and mass spectra as well as elemental analysis. Single‐crystal X‐ray diffraction revealed that complexes 3c and 4e adopt an octahedral geometry around the vanadium center. In the presence of Et₂AlCl as a cocatalyst, these complexes displayed high catalytic activities up to 22.8 kg PE/mmol_V.h.bar for ethylene polymerization, and produced high‐molecular‐weight polymers. Introducing additional oxygen atom on phosphorus atom of [O,P,O] ligands has resulted in significant changes on the aspect of steric/electronic effect, which has an impact on polymerization performance. 3c and 4c /Et₂AlCl catalytic systems were tolerant to elevated temperature (70 °C) and yielded unimodal polyethylenes, indicating the single‐site behavior of these catalysts. By pretreating with equimolar amounts of alkylaluminums, functional α‐olefin 10‐undecen‐1‐ol can be efficiently incorporated into polyethylene chains. 10‐Undecen‐1‐ol incorporation can easily reach 14.6 mol % under the mild conditions. Other reaction parameters that influenced the polymerization behavior, such as reaction temperature, Al/V (molar ratio), and comonomer concentration, are also examined in detail. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Ethylene/α‐olefin copolymerization with bis(β‐enaminoketonato) titanium complexes activated with modified methylaluminoxane

Copolymerizations of ethylene with α‐olefins (i.e., 1‐hexene, 1‐octene, allylbenzene, and 4‐phenyl‐1‐butene) using the bis(β‐enaminoketonato) titanium complexes [(Ph)NC(R₂)CHC(R₁)O]₂TiCl₂ ( 1a : R₁ = CF₃, R₂ = CH₃; 1b : R₁ = Ph, R₂ = CF₃; and 1c : R₁ = t‐Bu, R₂ = CF₃), activated with modified methylaluminoxane as a cocatalyst, have been investigated. The catalyst activity, comonomer incorporation, and molecular weight, and molecular weight distribution of the polymers produced can be controlled over a wide range by the variation of the catalyst structure, α‐olefin, and reaction parameters such as the comonomer feed concentration. The substituents R₁ and R₂ of the ligands affect considerably both the catalyst activity and comonomer incorporation. Precatalyst 1a exhibits high catalytic activity and produces high‐molecular‐weight copolymers with high α‐olefin insertion. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6323–6330, 2005     

Hydrogen effects in propylene polymerization reactions with titanium‐based Ziegler–Natta catalysts. II. Mechanism of the chain‐transfer reaction

Hydrogen is a very effective chain‐transfer agent in propylene polymerization reactions with Ti‐based Ziegler–Natta catalysts. However, measurements of the hydrogen concentration effect on the molecular weight of polypropylene prepared with a supported TiCl₄/dibutyl phthalate/MgCl₂ catalyst show a peculiar effect: hydrogen efficiency in the chain transfer significantly decreases with concentration, and at very high concentrations, hydrogen no longer affects the molecular weight of polypropylene. A detailed analysis of kinetic features of chain‐transfer reactions for different types of active centers in the catalyst suggests that chain transfer with hydrogen is not merely the hydrogenolysis reaction of the Ti? C bond in an active center but proceeds with the participation of a coordinated propylene molecule. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1899–1911, 2002     

Application of thiol‐ene click chemistry to preparation of functional polyethylene with high molecular weight and high polar group content: Influence of thiol structure and vinyl type on reactivity

A series of functional polyethylenes have been simply and efficiently synthesized via the combination of regioselective ethylene/5‐vinyl‐2‐norbornene (VNB) copolymerization using [PhNC(CF₃)CHCO(Ph)]₂TiCl₂ catalyst and following ultraviolet light initiated thiol‐ene click reaction. On treatment of ethylene/VNB copolymer with different thiols including mercaptoethanol, 1‐thioglycerol, methyl mercaptoacetate, methyl mercaptopropionate, 2‐mercaptoethylamine, mercaptoacetic acid, and mercaptopropanoic acid, various polar groups have been successfully introduced into the polyethylene. Except 2‐mercaptoethylamine, the functionalizations are quite efficient with the degree of functionalization higher than 94%, which is independent of thiol structure and double bond content. The content of polar group in functional polyethylene can be tuned in a wide range of 0–30 mol %. Gel permeation chromatography profiles indicate all functional polyethylenes that have very high molecular weights (160–336 kg/mol) with homogeneous formation. Besides, systematic investigation of the influence of vinyl type and thiol structure on reactivity has been also carried out. By treatment of mercaptoethanol with different copolymers (ethylene/VNB, ethylene/5‐ethylidene‐2‐norbornene, and ethylene/dicyclopentadiene copolymer), the order of vinyl reactivity can be summarized as terminal > internal > cyclic double bond. For different thiols, the reactivity has the sequence of SHCH₂COOH > SHCH₂COOCH₃ > SHCH₂CH₂COOH > SHCH₂CH₂COOCH₃ > SHCH₂CH(OH)CH₂OH > SHCH₂CH₂OH > SHCH₂CH₂NH₂, which is depended on the solubility and the electron‐withdrawing inductive effect of polar group. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Kinetic elucidation of comonomer‐induced chemical and physical activation in heterogeneous ziegler‐natta propylene polymerization

We have kinetically elucidated the origins of activity enhancement because of the addition of comonomer in Ziegler‐Natta propylene polymerization, using stopped‐flow and continuously purged polymerization. Stopped‐flow polymerization (with the polymerization time of 0.1–0.2 s) enabled us to neglect contributions of physical phenomena to the activity, such as catalyst fragmentation and reagent diffusion through produced polymer. The propagation rate constant k_p and active‐site concentration [C*] were compared between homopolymerization and copolymerization in the absence of physical effects. k_p for propylene was increased by 30% because of the addition of a small amount of ethylene, whereas [C*] was constant. On the contrary, both k_p (for propylene) and [C*] remained unchanged by the addition of 1‐hexene. Thus, only ethylene could chemically activate propylene polymerization. However, continuously purged polymerization for 30 s resulted in much more significant activation by the addition of comonomer, clearly indicating that the activation phenomenon mainly arises from the physical effects. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Facile,efficient functionalization of polyethylene via regioselective copolymerization of ethylene with cyclic dienes

The copolymerizations of ethylene with cyclic dienes [dicyclopentadiene (DCPD) and 2,5‐norbornadiene (NBD)] using bis(β‐enaminoketonato)titanium complexes [PhN = C(R₂)CHC(R₁)O]₂TiCl₂ ( 1a : R₁ = CF₃, R₂ = CH₃; 1b : R₁ = t‐Bu, R₂ = CF₃; 1c : R₁ = Ph, R₂ = CF₃) have been investigated. In the presence of modified methylaluminoxane, these complexes exhibited high catalytic activities in the copolymerization of ethylene with DCPD or NBD, affording high molecular weight copolymers with unimodal molecular weight distributions. ¹H and ¹³C‐NMR spectra reveal ethylene/DCPD copolymerizations by catalysts 1a – c proceeds through the enchainment of norbornene ring. Catalysts 1a and 1c showed a tendency to afford alternating copolymers. More noticeably, catalysts 1b and 1c bearing bulky substituents on the ligands promote ethylene/NBD copolymerization without crosslinking, affording the copolymer containing intracyclic double bonds. The NBD incorporation as high as 27.2 mol % has been achieved by catalyst 1c . Moreover, the microstructures of the copolymers were further confirmed by the measurement of reactivity ratios and dyad monomer sequences as well as mean sequence lengths. The intracyclic double bonds of ethylene/DCPD or ethylene/NBD copolymers can be fully converted into polar groups such as epoxy, amine, silane, and hydroxyl groups under mild conditions. Convenient synthesis of hydroxylated polyethylene can be provided for the first time through the ring opening reaction of epoxide. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1764–1772, 2010     

Propylene Polymerization Performance of Isolated and Aggregated Ti Species Studied Using a Well‐Designed TiCl3/MgCl2 Ziegler‐Natta Model Catalyst

In propylene polymerization with MgCl₂‐supported Ziegler‐Natta catalysts, it is known that the reduction of TiCl₄ with alkylaluminum generates Ti³⁺ active species, and at the same time, leads to the growth of TiCl_x aggregates. In this study, the aggregation states of the Ti species were controlled by altering the Ti content in a TiCl₃/MgCl₂ model catalyst prepared from a TiCl₃ · 3C₅H₅N complex. It is discovered that all the Ti species become isolated mononuclear with a highly aspecific feature below 0.1 wt.‐% of the Ti content, and that the isolated aspecific Ti species are more efficiently converted into highly isospecific ones by the addition of donors than active sites in aggregated Ti species.

     

Olefin polymerization and copolymerization by complexes bearing [ONNO]‐Type salan ligands: Effect of ligand structure and metal type (titanium,zirconium, and vanadium)

A series of novel titanium(IV) complexes bearing tetradentate [ONNO] salan type ligands: [Ti{2,2′‐(OC₆H₃‐5‐t‐Bu)₂‐NHRNH}Cl₂] (Lig¹TiCl₂: R = C₂H₄; Lig²TiCl₂: R = C₄H₈; Lig³TiCl₂: R = C₆H₁₂) and [Ti{2,2′‐(OC₆H₂‐3,5‐di‐t‐Bu)₂‐NHC₆H₁₂NH}Cl₂] (Lig⁴TiCl₂) were synthesized and used in the (co)polymerization of olefins. Vanadium and zirconium complexes: [ M{2,2′‐(OC₆H₃‐3,5‐di‐t‐Bu)₂‐NHC₆H₁₂NH}Cl₂] (Lig⁴VCl₂: M = V; Lig⁴ZrCl₂: M = Zr) were also synthesized for comparative investigations. All the complexes turned out active in 1‐octene polymerization after activation by MAO and/or Al(i‐Bu)₃/[Ph₃C][B(C₆F₅)₄]. The catalytic performance of titanium complexes was strictly dependent on their structures and it improves for the increasing length of the aliphatic linkage between nitrogen atoms (Lig¹TiCl₂ << Lig²TiCl₂ < Lig³TiCl₂) and declines after adding additional tert‐Bu group on the aromatic rings (Lig³TiCl₂ < Lig⁴TiCl₂). The activity of all titanium complexes in ethylene polymerization was moderate and the properties of polyethylene was dependent on the ligand structure, cocatalyst type, and reaction conditions. The Et₂AlCl‐activated complexes gave polymers with lover molecular weights and bimodal distribution, whereas ultra‐high molecular weight PE (up to 3588 kg mol^?1) and narrow MWD was formed for MAO as a cocatalyst. Vanadium complex yielded PE with the highest productivity (1925.3 kg mol_v^?1), with high molecular weight (1986 kg mol^?1) and with very narrow molecular weight distribution (1.5). Copolymerization tests showed that titanium complexes yielded ethylene/1‐octene copolymers, whereas vanadium catalysts produced product mixtures. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2111–2123     

Preparation of high cis‐1,4 polyisoprene with narrow molecular weight distribution via coordinative chain transfer polymerization

High cis‐1,4 polyisoprene with narrow molecular weight distribution has been prepared via coordinative chain transfer polymerization (CCTP) using a homogeneous rare earth catalyst composed of neodymium versatate (Nd(vers)₃), dimethyldichlorosilane (Me₂SiCl₂), and diisobutylaluminum hydride (Al(i‐Bu)₂H) which has strong chain transfer affinity is used as both cocatalyst and chain transfer agent (CTA). Differentiating from the typical chain shuttling polymerization where dual‐catalysts/CSA system has been used, one catalyst/CTA system is used in this work, and the growing chain swapping between the identical active sites leads to the formation of high cis‐1,4 polyisoprene with narrowly distributed molecular weight. Sequential polymerization proves that irreversible chain termination reactions are negligible. Much smaller molecular weight of polymer obtained than that of stoichiometrically calculated illuminates that, differentiating from the typical living polymerization, several polymer chains can be produced by one neodymium atom. The effectiveness of Al(i‐Bu)₂H as a CTA is further testified by much broad molecular weight distribution of polymer when triisobutylaluminum (Al(i‐Bu)₃), a much weaker chain transfer agent, is used as cocatalyst instead of Al(i‐Bu)₂H. Finally, CCTP polymerization mechanism is validated by continuously decreased M_w/M_n value of polymer when increasing concentration of Al(i‐Bu)₂H extra added in the Nd(ver)₃/Me₂SiCl₂/Al(i‐Bu)₃ catalyst system. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Living regioselective copolymerization of ethylene with nonconjugated bicyclic dienes using (salicylaldiminato)(β‐enaminoketonato) titanium catalysts

A series of heteroligated (salicylaldiminato)(β‐enaminoketonato)titanium complexes [3‐^tBu‐2‐OC₆H₃CH?N(C₆F₅)] [PhN?C(CF₃)CHCRO]TiCl₂ [ 3a : R = Ph, 3b : R = C₆H₄Cl(p), 3c : R = C₆H₄OMe(p), 3d : R = C₆H₄Me(p), 3e : R = C₆H₄Me(o)] were synthesized and characterized. Molecular structures of 3b and 3c were further confirmed by X‐ray crystallographic analyses. In the presence of modified methylaluminoxane as a cocatalyst, these unsymmetric catalysts displayed favorable ability to incorporate 5‐vinyl‐2‐norbornene (VNB) and 5‐ethylidene‐2‐norbornene (ENB) into the polymer chains, affording high‐molecular weight copolymers with high‐comonomer incorporations and alternating sequence under the mild conditions. The comonomer concentration in the polymerization medium had a profound influence on the molecular weight distribution of the resultant copolymer. At initial comonomer concentration of higher than 0.4 mol/L, the titanium complexes with electron‐donating groups in the β‐enaminoketonato moiety mediated room‐temperature living ethylene/VNB or ENB copolymerizations. Polymerization results coupled with density functional theory calculations suggested that the highly controlled living copolymerization is probably a consequence of the difficulty in chain transfer of VNB (or ENB)‐last‐inserted species and some characteristics of living ethylene polymerization under limited conditions. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Living syndiospecific polymerization of propylene promoted by C1‐symmetric titanium complexes activated by dried MAO

A series of C₁‐symmetric titanium complexes with both salicylaldiminato and β‐enaminoketonato as the ligands have been synthesized and investigated as the catalysts for propylene polymerization. In the presence of dried methylaluminoxane (dMAO), the complex with bulky substituent tert‐butyl ortho to alkyl oxygen can promote living polymerization of propylene with improved catalytic activity at ambient temperature, producing high molecular weight syndiotactic polypropylenes (rrrr 90.2%) with narrow molecular weight distributions (M_w/M_n = 1.07–1.22), via a propagation of 1,2‐insertion of monomer and chain‐end control of stereoselectivity. The propagation of polymer chain is completely different from that mediated by FI catalysts (the titanium complexes with phenoxy‐imine chelate ligands) which favor 2,1‐insertion of monomer. The interaction between a fluorine and a β‐hydrogen of a growing polymer chain, negligible chain transfer to monomer and dMAO without any free AlMe₃ were responsible for the achievement of living propylene polymerization. The substituent ortho to alkyl oxygen determined the stereo structure of the resultant polypropylene. In the case of less steric congested complexes with two nonequivalent coordination positions, the growing polymer chain might swing back to the favorite coordination position (site‐epimerization), forming m dyads regioirregular units. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Ethylene homopolymerizaton and copolymerizaton by vanadium(III) complexes containing tridentate or tetradentate iminopyrrolyl ligands

Iminopyrrolyl vanadium(III) complexes 2a–b bearing tridentate ligands [C₄H₃NCH?NC₆H₄L]VCl₂(THF) [L = 2‐P(C₆H₅)₂ ( 2a ), 2‐SMe ( 2b )] and complexes 2c–d with tetradentate ligands [(C₄H₃NCH?N)₂R]VCl(THF) [R = 1,2‐C₆H₄ ( 2c ), 1,2‐C₂H₄ ( 2d )] have been synthesized in high yields. With diethylaluminium chloride as a cocatalyst, complexes 2a–d were investigated as efficient catalysts for ethylene polymerization under various reaction conditions, and exhibited high catalytic activity and remarkable thermal stability. With these complexes, high molecular weight polymers with unimodal molecular weight distributions were obtained, indicating that the polymerization reaction took place in a single‐site nature. Ethylene/1‐hexene copolymerizations were also investigated in the presence of Et₂AlCl. Both increasing ligand denticity and introducing softer atom into the sidearm of the ligands significantly influenced catalytic activity, comonomer incorporation, and the molecular weights of the resultant polymers, suggesting that both the steric and the electronic effects of the ligands played an important role in adjusting chain propagation and transfer rate. The chain transfer mechanisms involved in the copolymerization process were investigated by carefully analyzing the microstructure of the copolymers. The signals of vinyl, disubstituted and tri‐substituted vinylene double bond end groups were detected in the copolymer obtained by 2a /Et₂AlCl system but not in those by 2b–c /Et₂AlCl systems, indicating that bulky electron‐donating group, ? P(C₆H₅)₂, may lead to those unusual transfer reactions. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Ethylene polymerization and ethylene/hexene copolymerization by vanadium(III) complexes bearing bidentate phenoxy‐phosphine oxide ligands

A series of novel vanadium(III) complexes bearing bidentate phenoxy‐phosphine oxide [O,P=O] ligands, (2‐R₁‐4‐R₂‐6‐Ph₂P=O‐C₆H₂O)VCl₂(THF)₂ ( 2a : R₁ = R₂ = H; 2b : R₁ = F, R₂ = H; 2c : R₁ = tBu, R₂ = H; 2d : R₁ = Ph, R₂ = H; 2e : R₁ = R₂ = Me; 2f : R₁ = R₂ = tBu; 2g : R₁ = R₂ = CMe₂Ph) have been synthesized by adding 1 equiv of the ligand to VCl₃(THF)₃ dropwise in the presence of excess triethylamine. Under the same conditions, the adding of VCl₃(THF)₃ to 2.0 equiv of the ligand afforded vanadium(III) complexes bearing two [O,P=O] ligands ( 3c , 3f ). All the complexes were characterized by FTIR and mass spectra as well as elemental analysis. Structures of complexes 2c and 3c were further confirmed by X‐ray crystallographic analysis. On activation with Et₂AlCl and ethyl trichloroacetate, these complexes displayed high catalytic activities for ethylene polymerization (up to 26.4 kg PE/mmol_V·h·bar) even at high reaction temperature (70 °C) indicative of high thermal stability, and produced high molecular weight polymers with unimodal molecular weight distributions. Additionally, the complexes with optimized structure exhibited high catalytic activities for ethylene/1‐hexene copolymerization. Catalytic activity, comonomer incorporation, and polymer molecular weight can be controlled in a wide range via the variation of catalyst structure and the reaction parameters such as Al/V molar ratio, comonomer feed concentration, and reaction temperature. The monomer reactivity ratios r_E and r_H were determined according to ¹³C NMR spectra, which indicated these complexes preferred ethylene to 1‐hexene in the copolymerization. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5298–5306     

Ethylene polymerization of the new titanium complexes bearing a phosphine oxide‐bridged bisphenolato ligand

A series of novel titanium(IV) complexes combining a phosphine oxide‐bridged bisphenolato ligand TiCl₂{2,2′‐O?P‐R₃ (4‐R₂‐6‐R₁‐C₆H₂O)₂}(THF) ( 6a : R₁ = tBu, R₂ = H, R₃ = Ph; 6b : R₁ = Ph, R₂ = H, R₃ = Ph; 6c : R₁ = R₂ = tBu, R₃ = Ph; 6d : R₁ = R₂ = cumyl, R₃ = Ph; 6e : R₁ = tBu, R₂ = H, R₃ = PhF₅) were prepared by the reaction of corresponding bisphenolato ligands with TiCl₄ in THF. X‐ray analysis reveals that complex 6a adopts distorted octahedral geometry around the titanium center. These catalysts were performed for ethylene polymerization in the presence of modified methyaluminoxane (MMAO). The effects of reaction parameters on ethylene polymerization behaviors, such as cocatalyst concentration, polymerization temperature, and reaction time were studied in detail. In general, these new complexes exhibited high catalytic activity, good temperature tolerance, and long lifetime for ethylene polymerization. The resulting polymers possess high molecular weight, unimodal distribution, and linear structure. © Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7062–7073, 2008