Preparation of Ag/C fiber with nanostructure through in situ thermally induced redox reaction between PVA and AgNO3 and its catalysis for 4‐nitrophenol reduction

A novel synthesized Ag/C fibrous catalyst based on in situ thermally induced redox reaction of PVA/AgNO₃ composite fibers was proposed. Utilizing the plasticization and complexation of AgNO₃ solution, the melt spinning of PVA/AgNO₃ composites was accomplished. Through the in situ thermally induced redox reaction on PVA/AgNO₃ composite fibers combined with carbonization of PVA and reduction of Ag+, the synthesized Ag/C fibrous catalyst was prepared with nanosilver particles with average diameter of 130 nm immobilized on the loose microstructural carbon layers. The synthesized Ag/C fibrous catalyst exhibited excellent catalytic activity and reused for at least five cycles for the reduction of 4‐nitrophenol, which may hold great promise in effective and eco‐friendly waste water treatment.     

Plasmonic Ag/AgCl‐modified bismuth subcarbonate with enhanced visible light photocatalytic activity

Plasmonic Ag/AgCl‐modified bismuth subcarbonate (Bi₂O₂CO₃) composites were prepared by a multistep process with hydrothermal, deposition, and photoreduction in the absence of organic capping agents. The properties of the obtained Ag/AgCl/Bi₂O₂CO₃ samples were characterized using X‐ray diffraction, field emission scanning electron microscopy and X‐ray photoelectron, UV–visible diffuse reflectance, and photoluminescence spectroscopies. The results reveal that Ag/AgCl nanoparticles are dispersed on the Bi₂O₂CO₃ surface to achieve plasmonic Ag/AgCl/Bi₂O₂CO₃. The Ag/AgCl/Bi₂O₂CO₃ nanocomposites show improved rhodamine B (RhB) adsorption capacity and photocatalytic activity compared with pure Bi₂O₂CO₃ and Ag/AgCl. In addition, the Ag/AgCl/Bi₂O₂CO₃ composite with 20 wt% Ag/AgCl exhibits the highest photocatalytic activity and remains stable for the photodegradation of RhB under visible light. The enhanced photocatalytic activity of Ag/AgCl/Bi₂O₂CO₃ may be attributed to the surface plasmon resonance effect of in situ generated Ag nanoparticles and synergistic effect of Ag/AgCl and Bi₂O₂CO₃, which increase the separation efficiency of photogenerated electron–hole pairs under visible light irradiation.     

In situ nitroxide‐mediated polymerization of styrene promoted by the N‐tert‐butyl‐α‐isopropylnitrone/bpo pair: ESR investigations

The styrene polymerization initiated by benzoyl peroxide (BPO) in the presence of N‐tert‐butyl‐α‐isopropylnitrone as nitroxide precursor is well‐controlled provided that a prereaction between the nitrone and BPO is carried out in suitable conditions prior to polymerization at a higher temperature. Electron spin resonance (ESR) spectroscopy was implemented to probe the nitroxides formed during both steps, that is, the prereaction and polymerization, and to get crucial information regarding the structure of the nitroxides responsible for the polymerization control. ESR studies combined with first principles calculations have evidenced that nitroxides observed during the prereaction in the presence of styrene and during the polymerization steps consist of a mixture of two macronitroxides. One is formed by the addition of a growing polystyrene chain to the nitrone as would be expected. However, the second one results from the addition of a polystyrene chain to tert‐butyl nitroso that is in situ formed presumably by decomposition of the first macronitroxide type. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Au/Ag复合纳米笼在表面增强拉曼光谱中的应用

表面增强拉曼光谱（SERS）技术是一种基于贵金属纳米结构基底对被检测物进行高灵敏度检测的一种方法.具有特殊纳米结构的贵金属表面受到激光的照射时，金属表面的自由电子会受到极大的振荡，当入射光频率与振荡频率相近时，则会发生表面等离子体共振现象（SPR），使金属表面的局域电场强度极大增强，入射光强度和散射光强度都得到成倍的放大，从而使吸附在贵金属纳米结构表面的分子的拉曼散射信号得到有效的增强.使用NaBH₄还原-酸刻蚀模板法，制备了八面体Au/Ag复合纳米笼，其形貌规整，尺寸均匀约为600 nm，无Cu₂O模板的残留，Au元素均匀负载在Ag纳米笼上，质量分数约为16.8%；Au/Ag复合纳米笼的紫外可见吸收峰相对于Ag纳米笼发生了红移，更重要的是，Au和Ag元素协同赋予了复合纳米笼超高的SERS灵敏度和重复性，Au/Ag复合纳米笼实现了对罗丹明6G的痕量检测（5×10^-14 mol/L），通过时域有限差分法（FDTD）模拟证实：这主要归因于等离子共振作用产生的高电磁场强度；此外，Au元素的加入使Au/Ag复合纳米笼具有优异的抗氧化性和化学稳定性，即使在1%的H₂O₂溶液中浸泡3 h，仍然能够保持优异的SERS性能.八面体Au/Ag复合纳米笼有望成为一种具有应用前景的高灵敏度、高稳定性的SERS基底.     

Morphology diagram of PE gel films in wide range temperature‐strain space: An in situ SAXS and WAXS study

Deformation‐induced structural evolution of polyethylene (PE) gel films were investigated by in situ synchrotron radiation SAXS and WAXS techniques during stretching at temperatures from 25°C to 110°C. The structural evolutions along tensile strains showed distinct behaviors in the four temperature regions divided by $T_{{\alpha }_{\mathrm{I}}}$ and $T_{{\alpha }_{\mathrm{II}}}$ given by DMA and the onset point of melting measured by DSC, respectively, which was determined by the coupling effects of external stretching field and temperature. Finally, the morphological diagrams of PE gel films on distinct scales including long period of lamellae, crystallinity, and crystal size in 2D temperature‐strain space were established, which can give a direct sight of membrane morphologies and act as a map for processing parameters selection. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 748–757     

Quantitative characterization of chemical degradation of heat‐treated wood surfaces during artificial weathering using XPS

The X‐ray photoelectron spectroscopy (XPS) study of three heat‐treated North American wood species (jack pine, birch and aspen) was carried out to evaluate chemical modifications occurring on the wood surface during artificial weathering for different times. The results suggest that the weathering reduces lignin content (aromatic rings) at the surface of heat‐treated wood, consequently, the carbohydrates content increases. This results in surfaces richer in cellulose and poorer in lignin. Heat‐treated wood surfaces become acidic due to weathering, and the acidity increases as the weathering time increases. Three possible reasons are given to account for the increase of acidity during weathering. The lignin content increases, whereas the hemicelluloses content decrease due to heat treatment. Heat‐treated woods have lower acidity to basicity ratios than the corresponding untreated woods for all three species because of the decrease in carboxylic acid functions mainly present in hemicelluloses. The wood composition changes induced by weathering are more significant compared to those induced by heat treatment at wood surface. Exposure to higher temperatures causes more degradation of hemicelluloses, and this characteristic is maintained during weathering. However, the wood direction has more effect on chemical composition modification during weathering compared to that of heat treatment temperature. The heat‐treated jack pine is affected most by weathering followed by heat‐treated aspen and birch. This is related to differences in content and structure of lignin of softwood and hardwood. The use of XPS technique has proved to be a reliable method for wood surface studies. Copyright © 2012 John Wiley & Sons, Ltd.     

Electron spin resonance study on chemical‐crosslinking reaction mechanisms of polyethylene using a chemical agent. VI. Effect of α‐methyl styrene dimer

The effect of α‐methyl styrene dimer (AMSD), which is used as a scorch retarder, on the reaction mechanisms of the chemical crosslinking of polyethylene (PE) with dicumyl peroxide (DCP) at high temperatures was investigated using electron spin resonance. When AMSD was added to PE containing DCP, the AMSD radical was observed; however, the PE alkyl radical or allyl radical presence was not detected. At 145 °C, crosslinking was obstructed as a result of the reaction between AMSD and alkyl radicals. As the temperature increased, AMSD fragmented to form 2‐phenyl‐2‐propyl and double bonds in PE. This generation of double bonds, however, accelerated crosslinking at 180 °C and was more effective than when AMSD was not present. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2151–2156, 2001     

Preparation and characterization of nematic polyazomethine/single‐walled carbon nanotube composites prepared by in situ polymerization

The synthesis and characterization of a series of nematic SWNT‐polyazomethine composites are described. The composites were prepared by in situ polymerization in the presence of 1 wt % of chemically modified SWNTs in such a way that they were either dispersed or covalently bonded to the polymeric matrix. The presence of the SWNTs did not alter the thermal behavior of the polymer matrix and, therefore, highly oriented fibers could be melt‐extruded from the composites at moderate temperatures, as revealed by structural and morphological studies. Preliminary tests on tensile properties indicate that strength and stiffness were improved when compared with fibers without CNTs, particularly when SWNTs were covalently bonded to the polymeric matrix. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2361–2372, 2009     

X‐ray photoelectron spectroscopy and the pattern recognition method—their application to surface studies in CoPd alloys

In the present work, polycrystalline CoPd alloys in varying range of bulk atomic percent composition (Co30Pd70, Co50Pd50 and Co70Pd30) are investigated by means of X‐ray photoelectron spectroscopy (XPS). The results of conventional XPS quantitative multiline (ML) approach are compared to the results obtained on the basis of XPS lines shape analysis, where the selected XPS or X‐ray induced Auger electron (XAES) transitions, are processed using the pattern recognition method known as the fuzzy k‐nearest neighbour (fkNN) rule. The fkNN rule is applied to the following spectra line shapes: Pd MNV, Co 2p, Co LMM, Pd 3d and valence band, analysing electrons in a varying range of selected kinetic energies. Both methods showed the surface segregation of Pd in Co30Pd70 and Co50Pd50 alloys. The results of the ML, the binding energy shift (ΔBE) analysis and the fkNN rule remained in agreement. Discrepancies in quantitative results obtained using different approaches are discussed within the accuracy of the applied methods, differences due to mean escape depth (MED) of electrons in considered transitions, their depth distribution function, the sensitivity of electron transition line shape on the environmental change (weaker effect for the inner shell transitions, and stronger effect for the outer shell transitions and Auger electron spectroscopy (AES) electrons transitions) and the non‐uniform depth profile concentrations. Copyright © 2005 John Wiley & Sons, Ltd.     

Formation of pore‐filled ion‐exchange membranes with in situ crosslinking: Poly(vinylbenzyl ammonium salt)‐filled membranes

Robust, polyelectrolyte‐filled, microporous membranes were prepared by the introduction and crosslinking of a preformed polymer within the pores of a poly(propylene) host membrane. Specifically, poly(vinylbenzyl chloride) (PVBCl) was reacted with piperazine or 1,4‐diaminobicyclo[2.2.2]octane in an N,N‐dimethylformamide (DMF) solution contained in the pores of the microporous base membrane. The remaining chloromethyl groups were reacted with an amine, such as trimethylamine, to form positively charged ammonium sites. This simple two‐step procedure gave dimensionally stable, anion‐exchange membranes in which the degree of crosslinking and the mass loading were determined by the concentration of PVBCl and crosslinker in the starting DMF solution. The incorporated polyelectrolyte gel was evenly distributed within the pores of the host membrane with no surface layers present. The membranes are fully characterized. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 807–820, 2001     

Relevance of a prereaction for the in situ NMP of styrene using the C‐Phenyl‐N‐tert‐butylnitrone/2,2′‐azobis(isobutyronitrile) pair

In this article, we compare two routes for carrying out in situ nitroxide‐mediated polymerization of styrene using the C‐phenyl‐N‐tert‐butylnitrone (PBN)/2,2′‐azobis(isobutyronitrile) (AIBN) pair to identify the best one for an optimal control. One route consists in adding PBN to the radical polymerization of styrene, while the other approach deals with a prereaction between the nitrone and the free radical initiator prior to the addition of the monomer and the polymerization. The combination of ESR and kinetics studies allowed demonstrating that when the polymerization of styrene is initiated by AIBN in the presence of enough PBN at 110 °C, fast decomposition of AIBN is responsible for the accumulation of dead polymer chains at the early stages of the polymerization, in combination with controlled polystyrene chains. On the other hand, PBN acts as a terminating agent at 70 °C with the formation of a polystyrene end‐capped by an alkoxyamine, which is not labile at this temperature but that can be reactivated and chain‐extended by increasing the temperature. Finally, the radical polymerization of styrene is better controlled when the nitrone/initiator pair is prereacted at 85 °C for 4 h in toluene before styrene is added and polymerized at 110 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1085–1097, 2009     

Controlled radical polymerization of styrene mediated by the C‐phenyl‐N‐tert‐butylnitrone/AIBN pair: Kinetics and electron spin resonance analysis

Kinetics of the free radical polymerization of styrene at 110 °C has been investigated in the presence of C‐phenyl‐N‐tert‐butylnitrone (PBN) and 2,2′‐azobis(isobutyronitrile) (AIBN) after prereaction in toluene at 85 °C. The effect of the prereaction time and the PBN/AIBN molar ratio on the in situ formation of nitroxides and alkoxyamines (at 85 °C), and ultimately on the control of the styrene polymerization at 110 °C, has been investigated. As a rule, the styrene radical polymerization is controlled, and the mechanism is one of the classical nitroxide‐mediated polymerization. Only one type of nitroxide (low‐molecular‐mass nitroxide) is formed whatever the prereaction conditions at 85 °C, and the equilibrium constant (K) between active and dormant species is 8.7 × 10^?10 mol L^?1 at 110 °C. At this temperature, the dissociation rate constant (k_d) is 3.7 × 10^?3 s^?1, the recombination rate constant (k_c) is 4.3 × 10⁶ L mol^?1 s^?1, whereas the activation energy (E_a,diss.), for the dissociation of the alkoxyamine at the chain‐end is ～125 kJ mol^?1. Importantly, the propagation rate at 110 °C, which does not change significantly with the prereaction time and the PBN/AIBN molar ratio at 85 °C, is higher than that for the thermal polymerization at 110 °C. This propagation rate directly depends on the equilibrium constant K and on the alkoxyamine and nitroxide concentrations, as well. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1219–1235, 2007     

XPS of oxygen atoms on Ag(111) and Ag(110) surfaces: Accurate study with SAC/SAC‐CI combined with dipped adcluster model

O1s core‐electron binding energies (CEBE) of the atomic oxygens on different Ag surfaces were investigated by the symmetry adapted cluster‐configuration interaction (SAC‐CI) method combined with the dipped adcluster model, in which the electron exchange between bulk metal and adsorbate is taken into account properly. Electrophilic and nucleophilic oxygens (O_elec and O_nuc) that might be important for olefin epoxidation in a low‐oxygen coverage condition were focused here. We consider the O1s CEBE as a key property to distinguish the surface oxygen states, and series of calculation was carried out by the Hartree–Fock, Density functional theory, and SAC/SAC‐CI methods. The experimental information and our SAC/SAC‐CI results indicate that O_elec is the atomic oxygen adsorbed on the fcc site of Ag(111) and that O_nuc is the one on the reconstructed added‐row site of Ag(110) and that one‐ and two‐electron transfers occur, respectively, to the O_elec and O_nuc adclusters from the silver surface. © 2013 Wiley Periodicals, Inc.     

In situ investigations of the interaction of small inorganic acidifying molecules in humidified air with polycrystalline metal surfaces by means of TM‐AFM,IRRAS, and QCM

Initial atmospheric corrosion of copper, silver, and iron induced by humidity and oxidizing agents was studied in situ by three highly surface‐sensitive and complementary techniques: infrared reflection‐absorption spectroscopy (IRRAS), quartz crystal microbalance (QCM), and tapping‐mode atomic force microscopy (TM‐AFM). These techniques deliver information about the change of the topography of the sample surfaces with emphasis on the shape and lateral distribution of the corrosion products grown within the first 1300–2800 min of weathering (TM‐AFM), as well as chemical (IRRAS) and kinetic (QCM) data. A completely different mechanism of the initial stages of atmospheric corrosion of the three investigated metals could be observed. A uniform growth of corrosion products was seen on the copper surface (identified by IRRAS and XPS to be cuprite‐like) during exposure to synthetic air with 80% relative humidity (RH), whereas the iron surface remained unattacked. The investigations of the silver surface exposed to humidity revealed that silver is attacked by humidity and tends to form oxide and hydroxide surface species. While an increased humidity content of the surrounding atmosphere causes higher corrosion rates on copper, on the exposed silver sample only a change in the degradation mechanism could be observed. The addition of SO₂ to the humidified air causes the growth of so‐called ‘second‐order’ features on copper, identified to be CuSO₃ · xH₂O‐like, which reveals the formation of a new chemical species on the investigated surface. These features are placed on top of the homogeneous formed oxide layer and tend to form well‐defined islands. In contrast to copper, on a silver surface exposed to humidity and SO₂ no new chemical species are formed; nevertheless an increased corrosion rate could be observed owing to a change of the chemistry in the physisorbed water layer. Iron exposed to humidity and SO₂ still remains unattacked. An iron surface is attacked only if exposed to humidity and SO₂ and NO₂, which show a synergistic effect by the oxidation of four‐valent sulfur‐oxygen species by NO₂. Such an attack leads to the formation of pitting corrosion, which was observed in situ and time‐resolved. The pits mainly occur on predamaged surface structures, such as scratches caused from the polishing process of the samples, and therefore promote the initiation of the corrosion. The results obtained demonstrate the high potential of the surface‐sensitive methods applied for investigating the early stages of corrosion of different metals and for obtaining a better understanding of the molecular mechanisms during degradation. Copyright © 2007 John Wiley & Sons, Ltd.     

Polymerization kinetics of rac‐lactide initiated with alcohol/stannous octoate using in situ attenuated total reflectance‐fourier transform infrared spectroscopy: An initiator study

rac‐Lactide polymerization kinetics in THF at 72 °C were monitored in real‐time using mid‐infrared ATR‐FTIR spectroscopy, with diamond composite insertion probe and light conduit technology. Monomer concentration as a function of time was acquired using the 1240 cm^?1 resonance associated with the ? CO? O? C? stretch. Polymerizations were initiated with either n‐propanol (PrOH), ethylene glycol (EG), trimethylol propane (TMP), or pentaerythritol (PENTA) with the coinitiator stannous octoate (Sn(Oct)₂). Polymerizations were found to be reversible at high monomer conversions, with a residual monomer concentration at 72 °C (345 K) of 0.081 M. The polymerizations were internally first‐order with respect to monomer, indicating a constant concentration of propagating centers. For a typical reaction with [rac‐LA]₀ = 1.0 M, [PENTA]₀ = 1.3 × 10^?2 M, and [Sn(Oct)₂] = 2.5 × 10^?2 M, the first‐order rate constant, k_app was measured as 1.8 × 10^?4 s^?1. First‐order rate constants were determined to be independent of polymer architecture (i.e., initiator functionality) and proportional to [Sn(Oct)₂] for [Sn(Oct)₂]₀/[ROH]₀ ? 1, where [ROH]₀ represents the initial concentration of initiating hydroxyl groups. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 797–803, 2009     

Si 2p XPS spectrum of the hydrogen‐terminated (100) surface of device‐quality silicon

An experimental study of the Si 2p XPS spectrum at different take‐off angles of atomically flat, hydrogen‐terminated 1 × 1 Si(100) is reported. The observed spectrum can be described accurately by considering three additional contributions to the spectrum of elemental silicon. Each contribution is attributed to a chemical state of silicon on the basis of its chemical shift with respect to elemental silicon and the depth of the region where it was originated. Copyright © 2003 John Wiley & Sons, Ltd.     

Application of the ETD/PTR reactions in top‐down proteomics as a faster alternative to bottom‐up nanoLC‐MS/MS protein identification

Our goal was to compare two popular analytical techniques used nowadays in proteomic investigations for proteins/peptides sequencing and identification, a widely used nanoLC‐MS/MS approach applied in the bottom‐up proteomics and electron transfer dissociation/proton transfer reaction fragmentation preferably used when top‐down strategy is applied. Comparison was carried out with the aid of the ESI‐quadrupole ion‐trap instrument using the following criteria: total time of analysis including sample preparation, sequence coverage, Mascot scoring, capability to detect modifications, quality of the results as a function of protein molecular weight and sample consumption. Copyright © 2012 John Wiley & Sons, Ltd.     

Influence of the preparation conditions of Pd‐ZrO2 and AuPd‐ZrO2 nanoparticle–decorated functionalised MWCNTs: Electron spectroscopy study aided with the QUASES

The Pd, AuPd, and ZrO₂ nanoparticle–decorated functionalised multiwalled carbon nanotubes (f‐MWCNTs) were reported as efficient catalysts of formic acid (FA) electro‐oxidation. Different preparation conditions influence their chemical and structural properties analysed by X‐ray photoelectron spectroscopy aided with the quantitative analysis of surfaces by electron spectroscopy. Different reduction procedures such as NaBH₄, a polyol microwave‐assisted method (PMWA), and a high pressure microwave reactor (HPMWR) were applied for decorating ZrO₂/f‐MWCNTs with Pd and AuPd nanoparticles. The ZrO₂ nanoparticles are attached through oxygen groups to the surface of f‐MWCNTs. In NaBH₄ and HPMWR procedures, Pd nanoparticles precipitate predominantly on ZrO₂ of nearly nominal stoichiometry, whereas in PMWA procedure, Pd and AuPd nanoparticles precipitate predominantly on the surface of f‐MWCNTs, bridging with oxygen groups and ZrO_x (x < 2) and leading to Pd‐O‐Zr phase formation. Strong reducing procedures (NaBH₄ and FA) led to smaller Pd nanoparticle size, Pd oxide content, and PdO_x overlayer thickness in contrary to weak reduction procedures (HPMWR and PMWA). The highest content of Pd‐O‐Zr phase appeared for Pd predominant precipitation on ZrO₂ nanoparticles (HPMWR) in contrary to Pd and AuPd predominant precipitation on surface of f‐MWCNTs (NaBH₄ ~ FA > PMWA). Larger content of Pd‐O‐Zr phase in AuPd‐decorated ZrO₂/f‐MWCNTs in contrary to Pd‐decorated sample (PMWA) could be justified by different electronic properties of nanoparticles. The FA treatment of Pd and AuPd‐ZrO₂/f‐MWCNTs samples provided decreasing Pd oxide content, overlayer thickness, nanoparticle size, increasing nanoparticle surface coverage and density, amount of Pd‐O‐Zr, what results from reduction of oxygen groups bridging with Pd and ZrO_x nanoparticles, also through Pd‐O‐Zr phase.     

In situ doping polymerization of polyaniline microtubules in the presence of β‐naphthalenesulfonic acid

Conducting microtubules of Polyaniline (PANI) were synthesized for the first time by the “in situ doping polymerization” method in the presence of β‐naphthal‐ enesulfonic acid (NSA) as dopant. Different doping methods, such as “immerse doping” and “grind doping,” and different synthetic conditions, such as molar ratio of aniline (An) to NSA (An/NSA), concentration of NSA in the polymerization media, reaction temperature, and time were investigated to understand the formation of microtubules. It was found that the PANI–NSA microtubules can be formed only by the “in situ doping polymerization” method, and the above synthetic conditions strongly affect the formation of the PANI–NSA microtubules, especially the molar ratio of An to NSA. An optimal condition was found under which tubules with 1–3 μm in diameter and 10–50 μm in length were obtained. The morphology of PANI–NSA tubules was proved by SEM and TEM, and their backbone structure was characterized by FTIR, UV‐VIS, XPS, and X‐ray diffraction. Results of these measurements showed that the molecular structures of the resulted PANI–NSA microtubules were identical to that of PANI–HCl synthesized by conventional method. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 151–157, 1999