有序Au/Ag纳米碗阵列的简易制备及其表面增强拉曼散射性能

通过湿法化学合成基于SiO₂胶体晶体的大面积有序Au/Ag纳米碗(Au/AgNB)阵列。首先,在玻璃基板上组装3D SiO₂胶体晶体作为模板。然后,以Au纳米颗粒(AuNP)为种子,通过原位生长法在SiO₂模板上沉积一层Au纳米壳(AuNS)。再通过HCHO还原Ag⁺成Ag⁰,进一步在AuNS表面沉积Ag纳米壳,形成Ag/Au双纳米壳(Ag/AuNS)阵列。最后通过丙烯酸酯改性双向取向聚丙烯(BOPP)膜方便地获得了单层有序反转Ag/AuNB阵列。这种有序Au/AgNB阵列具有更佳的表面增强拉曼散射(SERS)活性,其SERS分析增强因子(AEF)可达2.23×10⁷。     

有序Au/Ag纳米碗阵列的简易制备及其表面增强拉曼散射性能

通过湿法化学合成基于SiO₂胶体晶体的大面积有序Au/Ag纳米碗(Au/AgNB)阵列。首先,在玻璃基板上以3D SiO₂胶体晶体作为模板。然后,在Au纳米颗粒(AuNP)种子的帮助下,通过原位生长方法在模板上沉积一层Au纳米壳(AuNS)。再通过HCHO还原Ag⁺使AuNS表面进一步沉积Ag纳米壳,形成Ag/Au双纳米壳(Ag/AuNS)阵列。通过丙烯酸酯改性双向取向聚丙烯(BOPP)方便地获得了单层有序反转Ag/AuNB阵列。这种有序Au/AgNB阵列具有更佳的表面增强拉曼散射(SERS)活性,其SERS分析增强因子(AEF)可达2.23×10⁷。     

Silver nanocubes monolayers as a SERS substrate for quantitative analysis

Surface-enhanced Raman scattering (SERS) is a powerful spectroscopic tool in quantitative analysis of molecules, where the substrate plays a critical role in determining the detection performance. Herein, a silver nanocubes/polyelectrolyte/gold film sandwich structure was prepared as a reproducible, high-performance SERS substrate by the water/oil interfacial assembly method. In addition to the hot spots on the nanocubes surface, the edge-to-edge interspace of the Ag nanocubes led to marked enhancement of the SERS intensity, with a limit of detection of 10^?11 mol/L and limit of quantitation of 10^?10 mol/L for crystal violet. When rhodamine 6G and crystal violet were co-adsorbed on the Ag nanocube surfaces, the characteristic SERS peaks of the two molecules remained well resolved and separated, and the peak intensities varied with the respective concentration, which could be exploited for concurrent detection of dual molecules. Results from this work indicate that organized ensembles of Ag nanocubes can serve as effective SERS substrate can for sensitive analysis for complex molecular systems.     

Synthesis of Ag nanobars in the presence of single-crystal seeds and a bromide compound, and their surface-enhanced Raman scattering (SERS) properties

This Article describes the synthesis of Ag nanobars with different aspect ratios using a seed-mediated method and evaluation of their use for surface-enhanced Raman scattering (SERS). The formation of Ag nanobars was found to critically depend on the introduction of a bromide compound into the reaction system, with ionic salts being more effective than covalent molecules. We examined single-crystal seeds with both spherical and cubic shapes and found that Ag nanobars grown from spherical seeds had much higher aspect ratios than those grown from cubic seeds. The typical product of a synthesis contained nanocrystals with three different morphologies: nanocubes, nanobars with a square cross section, and nanobars with a rectangular cross section. Their formation can be attributed to the difference in growth rates along the three orthogonal <100> directions. The SERS enhancement factor of the Ag nanobar was found to depend on its aspect ratio, its orientation relative to the laser polarization, and the wavelength of excitation.     

Novel Silver/Poly(vinyl alcohol) Nanocomposites for Surface‐Enhanced Raman Scattering‐Active Substrates

Summary: Surface‐enhanced Raman scattering (SERS)‐active substrates with high enhancement were prepared by an in situ reduction method. Novel silver/poly(vinyl alcohol) (PVA) nanocomposite films were obtained, in which the silver nitrate, poly(γ‐glutamic acid) (PGA), and PVA acted as precursor, stabilizer, and polyol reducant, respectively. The UV‐visible spectra of the as‐fabricated films showed that the surface plasmon resonance (SPR) absorption band was narrow and of a stronger intensity, which indicates that the Ag nanoparticle size distribution on the substrate was highly uniform. This finding was further confirmed by X‐ray diffraction (XRD), transmission electron microscopy (TEM), and field‐emission scanning electron microscope (FE‐SEM) measurements. It was found that a PGA‐stabilized PVA nanocomposite film revealed the presence of well‐dispersed spherical silver nanoparticles with an average diameter of 90 nm. The new substrate presents high SERS enhancement and the enhanced factor is estimated to be 10⁶ for the detection of benzoic acid.

The Raman scattering enhancement factor for the Raman spectra of benzoic acid on the various nanocomposite films.     

Silver Nanoparticle Thin Films with Nanocavities for Surface‐Enhanced Raman Scattering

The formation of nanometer‐sized gaps between silver nanoparticles is critically important for optimal enhancement in surface‐enhanced Raman scattering (SERS). A simple approach is developed to generate nanometer‐sized cavities in a silver nanoparticle thin film for use as a SERS substrate with extremely high enhancement. In this method, a submicroliter volume of concentrated silver colloidal suspension stabilized with cetyltrimethylammonium bromide (CTAB) is spotted on hydrophobic glass surfaces prepared by the exposure of the glass to dichloromethysilane vapors. The use of a hydrophobic surface helps the formation of a more uniform silver nanoparticle thin film, and CTAB acts as a molecular spacer to keep the silver nanoparticles at a distance. A series of CTAB concentrations is investigated to optimize the interparticle distance and aggregation status. The silver nanoparticle thin films prepared on regular and hydrophobic surfaces are compared. Rhodamine 6G is used as a probe to characterize the thin films as SERS substrates. SERS enhancement without the contribution of the resonance of the thin film prepared on the hydrophobic surface is calculated as 2×10⁷ for rhodamine 6G, which is about one order of magnitude greater than that of the silver nanoparticle aggregates prepared with CTAB on regular glass surfaces and two orders of magnitude greater than that of the silver nanoparticle aggregates prepared without CTAB on regular glass surfaces. A hydrophobic surface and the presence of CTAB have an increased effect on the charge‐transfer component of the SERS enhancement mechanism. The limit of detection for rhodamine 6G is estimated as 1.0×10^?8 M . Scanning electron microscopy and atomic force microscopy are used for the characterization of the prepared substrate.     

Silver nanoparticles embedded temperature-sensitive nanofibrous membrane as a smart free-standing SERS substrate

To develop a smart free-standing surface enhanced Raman scattering(SERS) substrate,silver nanoparticles(AgNPs) embedded temperature-sensitive nanofibrous membrane was fabricated by electrospinning their aqueous solution containing the copolymer poly(N-isopropylacrylamide-co-Nhydroxymethylacrylamide),followed by heat treatment to form crosslinking structure within its constituent nanofibers.To avoid negative effect of the additive like stabilizer and the reactant like reductant on their SERS efficiency,the AgNPs were in-situ synthesized through reducing Ag~+ions dissolved in the polymer solution by ultraviolet irradiation.The prepared hybrid nanofibrous membrane with high stability in aqueous medium can reach its swelling or deswelling equilibrium state within 15 seconds with the medium temperature changing between 25℃and 50℃alternately.When it was used as a free-standing SERS substrate,10~(-12) mol/L of 4-nitrothiophenol in aqueous solution can be detected at room temperature,and elevating detection temperature can further lower its low detection limit.Since its generated SERS signal has desirable reproducibility,it can be used as SERS substrate for quantitative analysis.Moreover,the hybrid membrane as SERS substrate is capable of real-time monitoring the reduction of 4-nitrothiophenol into 4-aminothiophenol catalyzed by its embedded AgNPs,and the detected intermediate indicates that the reaction proceeds via a condensation route.     

Silver Molecularly Imprinting Polymer for the Determination of p-Nitroaniline by Surface Enhanced Raman Scattering

Molecular imprinting and surface enhanced Raman scattering (SERS) were used to prepare a core-shell Ag@molecularly imprinting polymer (MIP) for the determination of p-nitroaniline. The obtained Ag@MIP exhibits a detection limit of 10^?12 M, which demonstrates higher sensitivity toward p-nitroaniline than conventional approaches. In addition, the Ag@MIP shows good recyclability, and simultaneously offers better stability and high SERS activity for recognizing target molecules. To characterize the high SERS activity of the SERS-MIP hybrid material, a possible mechanism for the SERS substrate is proposed involving enhancement by the MIP. This study is expected to provide an alternative approach for the determination of p-nitroaniline in aqueous environments.     

Magnetic Ti3C2Tx/Fe3O4/Ag substrate for rapid quantification of trace sulfonamides in aquatic products by surface enhanced Raman spectroscopy

Surface-enhanced Raman scattering (SERS) spectroscopy has been employed as a rapid analysis technology for food security inspection recently. Nowadays, it is still a great challenge to rapidly quantify multiple trace antibiotics potentially abused in aquaculture industry. In this work, a magnetic Ti₃C₂T_x/Fe₃O₄/Ag substrate was prepared for the development of a reliable rapid SERS quantification method for multiple trace sulfonamides in aquatic products. This magnetic substrate had good uniformity, reproducibility, stability and SERS activity. Moreover, this substrate could integrate the magnetic separation-enrichment and matrix clean-up without cross contamination, which endowed it with good selectivity and anti-interference capability during real sample analysis. The electromagnetic enhancement and chemical enhancement mechanism of this magnetic substrate were studied in detail to reveal its good separation-enrichment performance and SERS activity. Finally, a rapid SERS quantification method was established and practically applied for trace phthalic sulfathiazole (PST) and silver sulfadiazine (SSD) in aquatic products by using Ti₃C₂T_x/Fe₃O₄/Ag magnetic substrates. Trace PST and SSD could be actually detected and quantified as 55.9 µg/kg and 64.0 µg/kg in aquatic products, respectively. Good recoveries of 83.9%–116% with relative standard deviations (RSDs) of 0.5%–3.2% for PST and 80.2%–102% with RSDs of 1.3%–5.8% for SSD were obtained. This work proposed an efficient and reliable method for rapid quantification of trace multiple sulfonamides in complex aquatic samples during food security inspection.     

Coating of silver nanoparticles (AgNPs) on glass fibers by a chemical method as plasmonic surface-enhanced Raman spectroscopy (SERS) sensors to detect molecular vibrations of Doxorubicin (DOX) drug in blood plasma

In the present study, Doxorubicin (DOX) drug in healthy blood plasma was the focus of the investigation by surface-enhanced Raman scattering (SERS). In recent years, chemotherapy has been the most popular treatment for various types of cancer; however, its adverse side effects on the patient's health have made a negative aspect regarding the use of this technique. DOX is the most common chemotherapy drug and is used for the treatment of an extensive range of human malignancies. The surface-enhanced Raman scattering (SERS) is a precise technique for the detection of chemicals and biomaterials with significantly low concentrations. The glass fiber substrates coated with silver nanoparticles (AgNPs) have been used to detect DOX. First, the Tollens' method was applied to prepare the AgNPs, and the characteristics of fabricated AgNPs were evaluated using ultraviolet–visible spectroscopy (UV–Vis) and X-ray diffraction (XRD). Then, AgNPs were coated on the glass fiber substrate by a chemical method. Finally, the enhancement of the Raman signal resulted from the molecular vibrations of DOX was evaluated using these SERS-active substrates as plasmonic and Raman spectroscopy sensors. Afterward, for making the sensors practical, the DOX in blood plasma were deposited on the fabricated sensors, and the Raman vibrations were evaluated. The SERS-active substrates, AgNPs deposited on glass fiber substrates, were fabricated for the detection of DOX in and out of the blood plasma; the limit of detection (LOD) for both was 10^?10 M, and the mean relative standard deviation at concentrations of 10^?10 M of DOX out of blood plasma, and 10^?10 M of DOX in blood plasma were obtained to be 3.76% and 3.61%, respectively for ten repeated measurements in which the AgNPs were SERS-active substrates of the biosensors for detecting the DOX. In addition, the enhancement factor was calculated both experimentally and via finite-difference time-domain (FDTD) simulation, which was 29.76 × 10³ and 24.95 × 10³, respectively. Therefore, these SERS-active substrates can be used to develop microsensors and show positive results for SERS-based investigations.     

Development of uncoated near-spherical gold nanoparticles for the label-free quantification of Lactobacillus rhamnosus GG by surface-enhanced Raman spectroscopy

The Surface-enhanced Raman spectroscopy (SERS) method based on gold nanoparticles as SERS substrate was investigated for the label-free detection and quantification of probiotic bacteria that are widely used in various pharmaceutical formulations. Indeed, the development of a simple and fast SERS method dedicated to the quantification of bacteria should be very useful for the characterization of such formulations in a more convenient way than the usually performed tedious and time-consuming conventional counting method. For this purpose, uncoated near-spherical gold nanoparticles were developed at room temperature by acidic treatment of star-like gold nanoparticle precursors. In this study, we first investigated the influence of acidic treatment conditions on both the nanoparticle physicochemical properties and SERS efficiency using Rhodamine 6G (R6G) as “model” analyte. Results highlighted that an effective R6G Raman signal enhancement was obtained by promoting chemical effect through R6G-anion interactions and by obtaining a suitable aggregation state of the nanoparticles. Depending on the nanoparticle synthesis conditions, R6G SERS signals were up to 10²–10³-fold greater than those obtained with star-like gold nanoparticles. The synthesized spherical gold nanoparticles were then successfully applied for the detection and quantification of Lactobacillus rhamnosus GG (LGG). In that case, the signal enhancement was especially due to the combination of anion-induced chemical enhancement and nanoparticle aggregation on LGG cell wall consecutive to non-specific interactions. Both the simplicity and speed of the procedure, achieved under 30 min, including nanoparticle synthesis, sample preparation, and acquisition of SERS spectra, appeared as very relevant for the characterization of pharmaceutical formulations incorporating probiotics.

Graphical abstract

     

Pt nanodendrites with (111) crystalline facet as an efficient,stable and pH-universal catalyst for electrochemical hydrogen production

High-performance nanomaterial catalysts for hydrogen evolution reaction via electrochemical water splitting are significant to the development of hydrogen energy. In this work, we report a robust and highly active catalyst fabricated through direct electrochemical deposition of Pt nanodendrites at the surface of activated carbon (Pt NDs). Owing to the large electrochemically active area and the exposed (111) facet of Pt, Pt NDs exhibits outstanding activity towards hydrogen evolution reaction with a low requiring overpotential of 0.027 V at 10 mA/cm² and Tafel slope of ≈ 22 mV/dec in acidic media. In addition, the hydrogen yield of Pt NDs is 30%–45% larger than that of commercial Pt/C at the same Pt loadings. Moreover, Pt NDs exhibits excellent long-term durability whose hydrogen production efficiency remains unchanged after six-hour hydrogen production, while the efficiency of commercial Pt/C catalyst decayed 9% under the same circumstance. Considering the superiority of catalytic activity and stability, this Pt NDs present great potentiality towards practical hydrogen production application.     

SERS and FDTD simulation of gold nanoparticles grafted on germanium wafer via galvanic displacement

Uniform and dense Au nanoparticles grown on Ge (Au/Ge) were fabricated by a facile galvanic displacement method and employed as surface‐enhanced Raman scattering (SERS) substrates. The substrates exhibited excellent reproducibility in the detection of rhodamine 6G aqueous solution with a relative standard deviation of <20%. The substrate showed a high Raman enhancement factor of 3.44 × 10⁶. This superior SERS sensitivity was numerical confirmed by the three‐dimensional finite‐difference time‐domain method, which demonstrated a stronger electric field intensity (|E/E₀|²) distribution around the Au nanoparticles grown on Ge. This facile and low‐cost prepared Au/Ge substrate with high SERS sensitivity and reproducibility might have potential applications in monitoring in situ reaction in aqueous solution. Copyright © 2014 John Wiley & Sons, Ltd.     

Highly reproducible surface-enhanced Raman scattering-active Au nanostructures prepared by simple electrodeposition: Origin of surface-enhanced Raman scattering activity and applications as electrochemical substrates

The fabrication of effective surface-enhanced Raman scattering (SERS) substrates has been the subject of intensive research because of their useful applications. In this paper, dendritic gold (Au) rod (DAR) structures prepared by simple one-step electrodeposition in a short time were examined as an effective SERS-active substrate. The SERS activity of the DAR surfaces was compared to that of other nanostructured Au surfaces with different morphologies, and its dependence on the structural variation of DAR structures was examined. These comparisonal investigations revealed that highly faceted sharp edge sites present on the DAR surfaces play a critical role in inducing a high SERS activity. The SERS enhancement factor was estimated to be greater than 10⁵, and the detection limit of rhodamine 6G at DAR surfaces was 10⁻⁸ M. The DAR surfaces exhibit excellent spot-to-spot and substrate-to-substrate SERS enhancement reproducibility, and their long-term stability is very good. It was also demonstrated that the DAR surfaces can be effectively utilized in electrochemical SERS systems, wherein a reversible SERS behavior was obtained during the cycling to cathodic potential regions. Considering the straightforward preparation of DAR substrates and the clean nature of SERS-active Au surfaces prepared in the absence of additives, we expect that DAR surfaces can be used as cost-effective SERS substrates in analytical and electrochemical applications.     

Surface-enhanced Raman scattering for quantitative detection of ethyl carbamate in alcoholic beverages

Ethyl carbamate, a by-product of fermentation and storage with widespread occurrence in fermented food and alcoholic beverages, is a compound potentially toxic to humans. In this work, a new approach for quantitative detection of ethyl carbamate in alcoholic beverages, based on surface-enhanced Raman scattering (SERS), is reported. Individual silver-coated gold nanoparticle colloids are used as SERS amplifiers, yielding high Raman enhancement of ethyl carbamate in three kinds of alcoholic beverages (vodka, Obstler, and white rum). The characteristic band at 1,003 cm^-1, which is the strongest and best reproducible peak in the SERS spectra, was used for quantitative evaluation of ethyl carbamate. The limit of detection, which corresponds to a signal-to-noise ratio of 3, was 9.0?×?10^-9 M (0.8 μg?·?L^-1), 1.3?×?10^-7 M (11.6 μg?·?L^-1), and 7.8?×?10^-8 M (6.9 μg?·?L^-1), respectively. Surface-enhanced Raman spectroscopy offers great practical potential for the in situ assessment and identification of ethyl carbamate in the alcoholic beverage industry.     

Au nanoparticles grafted on Fe3O4 as effective SERS substrates for label-free detection of the 16 EPA priority polycyclic aromatic hydrocarbons

Several methods and materials have been explored for the sensitive and practicable detection of polycyclic aromatic hydrocarbons (PAHs). However, it is still a challenge to develop simple and cost-effective sensing techniques for PAHs. Herein we report the synthesis and construction of Fe₃O₄@Au SERS substrate. This magnetic substrate was composed by Fe₃O₄ microspheres and Au NPs. The size, morphology, and surface composition of Fe₃O₄@Au were characterized by multiple complimentary techniques including scanning electron microscopy, X-ray photoelectron spectroscopy, and X-ray powder diffraction. The spatial distributions of electro-magnetic field enhancement around Fe₃O₄@Au was calculated using finite difference time domain (FDTD) simulations. As a result of its remarkable sensitivity, the Fe₃O₄@Au-based SERS assay has been applied to detect the 16 EPA priority PAHs. The LODs achieved by our method (100–5 nM, 16.6–1.01 μg L⁻¹) make it promising for the rapid screening of highly contaminated cases. As a proof-of-concept study, the substrate was applied in SERS sensing of PAHs in river matrix. The 16 PAHs could be differentiated based upon their characteristic SERS peaks. Most importantly, the detection was successfully conducted using a portable Raman spectrometer, which could be used for on-site monitoring of PAHs.     

Gas-Phase Deposited Plasmonic Nanoparticles Supported on 3D-Graphene/Nickel Foam for Highly SERS Detection

In this work, we proposed a novel three-dimensional (3D) plasmonic nanostructure based on porous graphene/nickel foam (GNF) and gas-phase deposited Ag nanoparticles (NPs).Ag NPs with high density were directly deposited on the surface of 3D GNF by performing a novel cluster beam deposition approach. In comparison with traditional Ag substrate(SiO₂/Ag), such hot-spots enriched 3D nanostructure showed extremely high electromag-netic field enhancement under incident light irradiation which could be used as a sensitive chemical sensor based on surface enhanced Raman scattering (SERS). The experimental results demonstrated that the proposed nanostructure showed superior SERS performance in terms of Raman signal reproducibility and sensitivity for the probe molecules. 3D full-wave simulation showed that the enhanced SERS performance in this 3D hierarchical plasmonic nanostructure was mainly obtained from the hot-spots between Ag NPs and the near-field coupling between Ag NPs and GNF sca olds. This work can provide a novel assembled SERS substrate as a SERS-based chemical sensor in practical applications.     

Silver overlayer-modified surface-enhanced Raman scattering-active gold substrates for potential applications in trace detection of biochemical species

Because Ag and Au nanoparticles (NPs) possess well-defined localized surface plasmon resonance (LSPR) they are popularly employed in the studies of surface-enhanced Raman scattering (SERS). As shown in the literature and in our previous studies, the advantage of SERS-active Ag NPs is their higher SERS enhancement over Au NPs. On the other hand, the disadvantage of SERS-active Ag NPs compared to Au NPs is their serious decay of SERS enhancement in ambient laboratory air. In this work, we develop a new strategy for preparing highly SERS-active Ag NPs deposited on a roughened Au substrate. This strategy is derived from the modification of electrochemical underpotential deposition (UPD) of metals. The coverage of Ag NPs on the roughened Au substrate can be as high as 0.95. Experimental results indicate that the SERS of Rhodamine 6G (R6G) observed on this developed substrate exhibits a higher intensity by ca. 50-fold of magnitude, as compared with that of R6G observed on the substrate without the deposition of Ag NPs. The limit of detection (LOD) for R6G measured on this substrate is markedly reduced to 2 × 10⁻¹⁵ M. Moreover, aging of SERS effect observed on this developed substrate is significantly depressed, as compared with that observed on a generally prepared SERS-active Ag substrate. These aging tests were performed in an atmosphere of 50% relative humidity (RH) and 20% (v/v) O₂ at 30 °C for 60 day. Also, the developed SERS-active substrate enables it practically applicable in the trace detection of monosodium urate (MSU)-containing solution in gouty arthritis without a further purification process.     

Non-labeling multiplex surface enhanced Raman scattering (SERS) detection of volatile organic compounds (VOCs)

In this paper, we report multiplex SERS based VOCs detection with a leaning nano-pillar substrate. The VOCs analyte molecules adsorbed at the tips of the nano-pillars produced SERS signal due to the field enhancement occurring at the localized surface plasmon hot spots between adjacent leaning nano-pillars. In this experiment, detections of acetone and ethanol vapor at different concentrations were demonstrated. The detection limits were found to be 0.0017 ng and 0.0037 ng for ethanol and acetone vapor molecules respectively. Our approach is a non-labeling method such that it does not require the incorporation of any chemical sensing layer for the enrichment of gas molecules on sensor surface. The leaning nano-pillar substrate also showed highly reproducible SERS signal in cyclic VOCs detection, which can reduce the detection cost in practical applications. Further, multiplex SERS detection on different combination of acetone and ethanol vapor was also successfully demonstrated. The vibrational fingerprints of molecular structures provide specific Raman peaks for different VOCs contents. To the best of our knowledge, this is the first multiplex VOCs detection using SERS. We believe that this work may lead to a portable device for multiplex, specific and highly sensitive detection of complex VOCs samples that can find potential applications in exhaled breath analysis, hazardous gas analysis, homeland security and environmental monitoring.     

3D aluminum/silver hierarchical nanostructure with large areas of dense hot spots for surface‐enhanced raman scattering

Plasmonic nanomaterials possessing large‐volume, high‐density hot spots with high field enhancement are highly desirable for ultrasensitive surface‐enhanced Raman scattering (SERS) sensing. However, many as‐prepared plasmonic nanomaterials are limited in available dense hot spots and in sample size, which greatly hinder their wide applications in SERS devices. Here, we develop a two‐step physical deposition protocol and successfully fabricate 3D hierarchical nanostructures with highly dense hot spots across a large scale (6 × 6 cm²). The nanopatterned aluminum film was first prepared by thermal evaporation process, which can provide 3D quasi‐periodic cloud‐like nanostructure arrays suitable for noble metal deposition; then a large number of silver nanoparticles with controllable shape and size were decorated onto the alumina layer surfaces by laser molecular beam epitaxy, which can realize large‐area accessible dense hot spots. The optimized 3D‐structured SERS substrate exhibits high‐quality detection performance with excellent reproducibility (13.1 and 17.1%), whose LOD of rhodamine 6G molecules was 10^?9 M. Furthermore, the as‐prepared 3D aluminum/silver SERS substrate was applied in detection of melamine with the concentration down to 10^?7 M and direct detection of melamine in infant formula solution with the concentration as low 10 mg/L. Such method to realize large‐area hierarchical nanostructures can greatly simplify the fabrication procedure for 3D SERS platforms, and should be of technological significance in mass production of SERS‐based sensors.