Near‐infrared electrochromic poly(aryl ether)s based on isolated electroactive tetraphenyl‐p‐phenylenediamine moieties

A series of near‐infrared (NIR) electrochromic aromatic poly(aryl ether)s containing N,N,N′,N′‐tetraphenyl‐p‐phenylenediamine (TPPA) moieties in the backbone were prepared from the high‐temperature polycondensation reactions of a biphenol monomer, 2,5‐bis(diphenylamino)hydroquinone, with difluoro compounds. The obtained polymers were readily soluble in many organic solvents and showed useful levels of thermal stability associated with high glass‐transition temperatures (182–205 °C) and high char yields (higher than 40% at 800 °C in nitrogen). The polymer films showed reversible electrochemical oxidation with high contrast ratio both in the visible range and NIR region, and also exhibited high coloration efficiency (CE), low switching time, and stability for electrochromic operation. The polyether TPPA‐a thin film revealed good CE in visible (CE = 217 cm²/C) and NIR (CE = 192 cm²/C) region with reversible electroactive stability (over 500 times within 5% loss relative to its initial injected charge). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5378–5385, 2009     

Novel UV‐induced photografting process for preparing poly(tetrafluoroethylene)‐based proton‐conducting membranes

A novel process comprising the UV‐induced photografting of styrene into poly(tetrafluoroethylene) (PTFE) films and subsequent sulfonation has been developed for preparing proton‐conducting membranes. Although under UV irradiation the initial radicals were mainly generated on the surface of the PTFE films by the action of photosensitizers such as xanthone and benzoyl peroxide, the graft chains were readily propagated into the PTFE films. The sulfonation of the grafted films was performed in a chlorosulfonic acid solution. Fourier transform infrared and scanning electron microscopy were used to characterize the grafted and sulfonated membranes. With a view to use in fuel cells, the proton conductivity, water uptake, and mechanical properties of the prepared membranes were measured. Even through the degree of grafting was lower than 10%, the proton conductivity in the thickness direction of the newly prepared membranes could reach a value similar to that of a Nafion membrane. In comparison with γ‐ray radiation grafting, UV‐induced photografting is very simple and safe and is less damaging to the membranes because significant degradation of the PTFE main chains can be avoided. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2624–2637, 2007     

Proton‐conducting polymers based on benzimidazoles and sulfonated benzimidazoles

A sulfonated derivative of polybenzimidazole is reported, and its properties are analyzed in comparison with related polybenzimidazole proton‐conducting materials. Poly(2,5‐benzimidazole), poly(m‐phenylenebenzobisimidazole), and poly[m‐(5‐sulfo)‐phenylenebenzobisimidazole] were prepared by condensation of the corresponding monomers in polyphosphoric acid. Several adducts of these polymers with phosphoric acid were prepared. The resulting materials were characterized by chemical analysis, Fourier transform infrared spectroscopy, and thermogravimetric analysis; also, the dc conductivity of doped and undoped derivatives was measured. Similar to what has been observed for the commercial polybenzimidazole polymer (also examined here for comparison), the title polymers exhibit high thermal stability. Furthermore, their doping with phosphoric acid leads to a significant increase in conductivity from less than 10^?11 Scm^?1 for the undoped polymers to 10^?4 Scm^?1 (both at room temperature) for their acid‐loaded derivatives. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3703–3710, 2002     

Synthesis and characterization of sulfonated copolyethersulfones

The present article deals with the synthesis and characterization of some sulfonated copolyethersulfones. The synthetic approach differs from the post sulfonation approach traditionally reported in the literature. The synthetic procedure is based on the use of sulfonated monomers which are then reacted with previously synthesized telechelic hydoxy‐ended poly (ether sulpnone)s. Combining the MALDI‐TOF MS and ¹H NMR analyses, with SEC‐Viscometry and TGA measurements, we demonstrate a powerful tool for characterizing the chemical composition, end chains, degree of sulfonation (DS) and molecular mass distribution (MMD) of disulfonated poly(arylene ether‐sulfone) copolymers. The characterization techniques allowed to determine the exact nature of the copolymers synthesized and to reveal some interesting features about the reaction. DMA data show that the glass transition temperature of sulfonated copolymers with similar DS increase as raise their MMD. Copolymers with a DS of 10–11 mol % reach a T_g of 244–246 °C. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3010–3023, 2010     

Synthesis and proton conductivity studies of polystyrene‐based triazole functional polymer membranes

In this study, poly(vinylbenzylchloride) (PVBC) was produced by free‐radical polymerization of 4‐vinylbenzylchloride, and then it was functionalized with 3‐amino‐1,2,4‐triazole (ATri) and 1H‐1,2,4‐triazole (Tri). The composition of the polymers was verified by elemental analysis, and the structure was characterized by Fourier transform infrared and ¹³C‐nuclear magnetic resonance spectra. PVBC was modified by ATri with 68% and Tri with 50% yield. The polymers were doped with trifluoromethanesulfonic acid (TA) at various molar ratios, X = 0.5, 1, 2, and 3 with respect to aminotriazole and triazole units. Proton transfer from TA to the triazole rings was proved with Fourier transform infrared spectroscopy. Thermogravimetric analysis showed that the samples are thermally stable up to approximately 200 °C. Differential scanning calorimetry results illustrated the homogeneity of the materials. Under anhydrous conditions, PVBCATri3TA and PVBCTri3TA showed highest proton conductivity of 0.086 and 0.042 S/cm, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and characterization of sulfonated poly(phthalazinone ether ketone) for proton exchange membrane materials

As a novel class of proton exchange membrane materials for use in fuel cells, sulfonated poly(phthalazinone ether ketone)s (SPPEKs) were prepared by the modification of poly(phthalazinone ether ketone). Sulfonation reactions were conducted at room temperature with mixtures of 95–98% concentrated sulfuric acid and 27–33% fuming sulfuric acid with different acid ratios, and SPPEK was obtained with a degree of sulfonation (DS) in the desired range of 0.6–1.2. The presence of sulfonic acid groups in SPPEK was confirmed by Fourier transform infrared analysis, and the DS and structures were characterized by NMR. The introduction of sulfonic groups into the polymer chains increased the glass‐transition temperature above the decomposition temperature and also led to an overall decrease in the decomposition temperature. Membrane films were cast from SPPEK solutions in N,N‐dimethylacetamide. Water uptakes and swelling ratios of SPPEK membrane films increased with DS, and SPPEKs with DS > 1.23 were water‐soluble at 80 °C. Proton conductivity increased with DS and temperature up to 95 °C, reaching 10^?2S/cm. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 497–507, 2003     

Direct copolymerization of sulfonated poly(phthalazinone arylene ether)s for proton‐exchange‐membrane materials

Sulfonated poly(phthalazinone ether ketone) (SPPEK) copolymers and sulfonated poly(phthalazinone ether sulfone) (SPPES) copolymers containing pendant sodium sulfonate groups were prepared by direct copolymerization. The reaction of disodium 3,3′‐disulfonate‐4,4′‐difluorobenzophenone (SDFB‐Na), 4,4′‐difluorobenzophenone (DFB), and 4‐(4‐hydroxyphenyl)‐1(2H)‐phthalazinone (DHPZ) at 170 °C in N‐methyl‐2‐pyrrolidione containing anhydrous potassium carbonate gave SPPEKs. SPPESs were similarly obtained with 3,3′‐disulfonate‐4,4′‐difluorophenyl sulfone, 4‐fluorophenyl sulfone (DFS), and DHPZ as monomers. The sulfonic acid groups, being on deactivated positions of the polymer backbone, were expected to be hydrolytically more stable than postsulfonated polymers. Fourier transform infrared and ¹H NMR were used to characterize the structures and degrees of sulfonation of the sulfonated polymers. Membrane films of SPPEKs with SDFB‐Na/DFB molar feed ratios of up to 60/40 and SPPESs with sulfonated 4‐fluorophenyl sulfone/DFS molar feed ratios of up to 50/50 were cast from N,N‐dimethylacetamide polymer solutions. Membrane films in acid form were then obtained by the treatment of the sodium‐form membrane films in 2 N sulfuric acid at room temperature. An increase in the number of sulfonate groups in the copolymers resulted in an increased glass‐transition temperature and enhanced membrane hydrophilicity. The sodium‐form copolymers were thermally more stable than their acid forms. The proton conductivities of the acid‐form copolymers with sulfonated monomer/unsulfonated monomer molar feed ratios of 0.5 and 0.6 were higher than 10^?2 S/cm and increased with temperature; they were less temperature‐dependent than those of the postsulfonated products. SPPESH‐50 showed higher conductivity than the corresponding postsulfonated poly(phthalazinone ether sulfone). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2731–2742, 2003     

Preparation and characterization of layer‐by‐layer self‐assembly membrane based on sulfonated polyetheretherketone and polyurethane for high‐temperature proton exchange membrane

A concept of preparing high‐temperature proton exchange membranes with layer‐by‐layer (LBL) self‐assembly technique was proposed and the sulfonated polyetheretherketone (SPEEK) and polyurethane (PU) with 200 LBL deposition cycles denoting (SPEEK/PU)₂₀₀ membrane was prepared in this research. Owing to the strong electrostatic interaction between ? group in SPEEK and ? C? N⁺ group in PU, (SPEEK/PU)₂₀₀ membrane with LBL self‐assembly structure showed a favorable structural stability. The phosphoric acid (PA)‐doped (SPEEK/PU)₂₀₀ membrane showed a higher proton conductivity relative to PA doped SPEEK/PU membrane by solution casting method (SPEEK/PU)₂₀₀/40%PA membrane possessed a proton conductivity value of 2.90 × 10^?2 S/cm at 150 °C under anhydrous conditions. The LBL self‐assembly structure provided a possibility to reduce the negative effect from polymer skeleton blocking charge carrier species even immobilizing protons. Moreover, the (SPEEK/PU)₂₀₀ membrane presented the particularly noteworthy mechanical property even with PA doping. The tensile stress values at break were 72.8 and 24.1 MPa, respectively, for (SPEEK/PU)₂₀₀ and (SPEEK/PU)₂₀₀/40%PA membrane at room temperature, which were obviously higher than the reported values of 15.9 and 2.81 MPa for SPEEK/PU and SPEEK/PU/60%PA membrane. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 3446–3454     

Highly proton conducting proton‐exchange membranes based on fluorinated poly(arylene ether ketone)s with octasulfonated segments

A new bisphenol monomer containing a pair of electron‐rich tetra‐arylmethane units was designed and synthesized. Based on this monomer, along with commercial 4,4′‐(hexafluoroisopropylidene)diphenol A and 4,4′‐difluorobenzophenone, a series of novel poly(arylene ether ketone)s containing octasulfonated segments of varying molar percentage (x) (6F‐SPAEK‐x) were successfully synthesized by polycondensation reactions, followed by sulfonation. Tough, flexible, and transparent membranes, exhibiting excellent thermal stabilities and mechanical properties were obtained by casting. 6F‐SPAEK‐x samples exhibited appropriate water uptake and swelling ratios at moderate ion exchange capacities (IECs) and excellent proton conductivities. The highest proton conductivity (215 mS cm⁻¹) is observed for hydrated 6F‐SPAEK‐15 (IEC = 1.68 meq g⁻¹) at 100 °C, which is more than 1.5 times that of Nafion 117. Furthermore, the 6F‐SPAEK‐10 membrane exhibited comparable proton conductivity (102 mS cm⁻¹) to that of Nafion 117 at 80 °C, with a relatively low IEC value (1.26 meq g⁻¹). Even under 30% relative humidity, the 6F‐SPAEK‐20 membrane (2.06 meq g⁻¹) showed adequate conductivity (2.1 mS cm⁻¹) compared with Nafion 117 (3.4 mS cm⁻¹). The excellent comprehensive properties of these membranes are attributed to well‐defined nanophase‐separated structures promoted by strong polarity differences between highly ionized and fluorinated hydrophobic segments. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 25–37     

Donor–acceptor‐based poly(toluidine‐co‐chloroaniline)s: Synthesis and characterization

A series of poly(o‐/m‐toluidine‐co‐o‐/m‐chloroaniline) copolymers of different compositions were synthesized by an emulsion method with ammonium persulfate as the oxidant. The conductivity of the copolymers was two to five orders of magnitude higher than that of the homopolymers poly(o‐toluidine) and poly(m‐chloroaniline). Among the copolymers, the copolymer of o‐toluidine and m‐chloroaniline exhibited a maximum conductivity of 0.14 S cm^?1. The conductivity of these copolymers was also higher than that of poly(aniline‐co‐chloroaniline). The properties of the copolymers were greatly influenced by the positions of the substituents and the concentrations of the individual monomers in the feed. All the copolymers were completely soluble in polar solvents such as dimethyl sulfoxide and showed higher heat stability as the chloroaniline concentration increased. These effects could be interpreted in terms of extensive hydrogen bonding and interchain linking and, therefore, higher electron delocalization in these copolymers due to the presence of electron‐rich toluidine rings adjacent to electron‐deficient chloroaniline. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1579–1587, 2005     

Synthesis and properties of novel benzimidazole‐containing sulfonated polyethersulfones for fuel cell applications

A novel series of benzimidazole‐containing sulfonated poly(arylene sulfones)s with controllable amount of basic 2,6‐bis(benzimidazol‐2‐yl)pyridine (BIP) and sulfonic acid groups have been prepared by the copolycondensation of a new BIP‐containing arylene difluoride monomer (DFSBIP) with a sulfonated arylene difluoride (DSDFS) and 4,4′‐biphenol (BP). All the resulting polymers have high molecular weights, good thermal stability, and can form uniform and tough membranes by simple solution casting. Because of the strong acid–base interaction between BIP and sulfonic acid groups, ionic crosslinking networks forms that resulted in polymer membranes with good dimensional stability in water even at high temperature (e.g., 100 °C). The ion exchange capacity (IEC) of the polymer membranes was investigated through a new simple pH‐determination method. A comparison between the experimental IEC values with the calculated ones based on the polymer structures indicated that each BIP unit interacted with one sulfonic acid group. Thus, by controlling the relative content of BIP units and sulfonate groups in the polymers, the intra‐ and intermolecular acid–base interactions could be readily optimized so as to achieve polymers with high IEC values, high proton conductivities as well as low swelling ratios, demonstrating good potential for proton exchange membrane applications. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1920–1929, 2009     

Morphological study on water‐borne conducting polyaniline‐poly(ethylene oxide) blends

Conducting polyaniline‐poly(ethylene oxide) blends were prepared from their aqueous solutions. The blends displayed an electrical conductivity percolation threshold as low as 1.83 wt % of polyaniline loading. As demonstrated by scanning electron microscopy, polarized optical microscopy, and wide‐angle X‐ray diffraction studies, the conducting polyaniline took a fibrillar morphology in the blend, and it existed only in the amorphous phase of poly(ethylene oxide). A three‐phase model combining morphological factors instead of a two‐phase model was proposed to explain the low‐conductivity percolation threshold. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 605–612, 2002; DOI 10.1002/polb.10114     

9,9‐Diaryl‐4,5‐diazafluorene‐based Cardo polymer; Synthesis and characteristic properties

To open out new aspects of 9,9‐diarylfluorene (DAF)‐based polymers with high performances, 9,9‐(4‐hydroxyphenyl)‐4,5‐diazafluorene ( N‐BPF ) was designed as a new cardo structure and the properties of poly(ether ketone)s ( N‐PEKs ) containing N‐BPF skeletons were examined in detail. N‐PEKs were synthesized in high yields via polycondensation of N‐BPF with difluoroarenes. N‐PEKs showed cardo polymer‐specific properties such as high thermal stability and high solubility in organic solvents. The addition of p‐toluenesulfonic acid (TsOH) to N‐PEK resulted in the formation of network polymer based on interchain hydrogen bonds. It turned out that the films of network polymer are flexible and transparent and exhibit high refractive index and low birefringence. The effects of feed ratio of TsOH to N‐PEK were also evaluated on the mechanical properties of network polymer. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4541–4549     

Lewis Acid‐Induced N‐Methyleneamines as Initiators in the Synthesis of Secondary Amine‐Terminated Polymers

Summary: The cationic polymerization of poly(tert‐butyl vinyl ether) using N‐methyleneamine equivalents derived from a Lewis acid/1,3,5‐trimethylhexahydro‐1,3,5‐triazine (TMTA) co‐initiating system is reported. The resulting polymers possessed secondary amine functionality at the chain terminus, verified by derivatization with 4‐chloro‐7‐nitrobenzo‐2‐oxa‐1,3‐diazole (NBD‐Cl) and subsequent analysis with GPC‐UV (470 nm) and ¹H NMR.

Use of N‐methyleneamine equivalents lacking aryl substituents to afford amine‐terminated poly(tert‐butyl vinyl ether).     

Synthesis and characterization of sulfonated poly(benzoxazole ether ketone)s by direct copolymerization as novel polymers for proton-exchange membranes

A new series of sulfonated poly(benzoxazole ether ketone)s (SPAEKBO-X) were prepared by the aromatic nucleophilic polycondensation of 4,4′-(hexafluoroisopropylidene)-diphenol with 2,2′-bis[2-(4-fluorophenyl)benzoxazol-6-yl]hexafluoropropane and sodium 5,5′-carbonylbis-2-fluorobenzenesulfonate in various ratios. Fourier transform infrared and ¹H NMR were used to characterize the structures and sulfonic acid contents of the copolymers. The copolymers were soluble in N-methyl-2-pyrrolidinone, N,N-dimethylacetamide, and N,N-dimethylformamide and could form tough and flexible membranes. The protonated membranes were thermally stable up to 320 °C in air. The water uptake, hydrolytic and oxidative stability, and mechanical properties were evaluated. At 30–90 °C and 95% relative humidity, the proton conductivities of the membranes increased with the sulfonic acid content and temperature and almost reached that of Nafion 112. At 90–130 °C, without external humidification, the conductivities increased with the temperature and benzoxazole content and reached above 10⁻² S/cm. The SPAEKBO-X membranes, especially those with high benzoxazole compositions, possessed a large amount of strongly bound water (>50%). The experimental results indicate that SPAEKBO-X copolymers are promising for proton-exchange membranes in fuel cells, and their properties might be tailored by the adjustment of the copolymer composition for low temperatures and high humidity or for high temperatures and low humidity; they are especially promising for high-temperature applications. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2273–2286, 2007     

Synthesis and properties of novel sulfonated polyimides containing 1,5‐naphthylene moieties

A series of novel sulfonated polyimides (equivalent weight per sulfonic acid = 310–744 g/equiv) containing 10–70 mol % 1,5‐naphthylene moieties were synthesized as potential electrolyte materials for high‐temperature polymer electrolyte fuel cells. The polycondensation of 1,4,5,8‐naphthalene tetracarboxylic dianhydride, 4,4′‐diamino‐2,2′‐biphenyldisulfonic acid, and 1,5‐diaminonaphthalene gave the title polymer electrolytes. The polyimide electrolytes were high‐molecular‐weight (number‐average molecular weight = 36.0–350.7 × 10³ and weight‐average molecular weight = 70.4–598.5 × 10³) and formed flexible and tough films. The thermal properties (decomposition temperature > 260 °C, no glass‐transition temperature), stability to oxidation, and water absorption were analyzed and compared with those of perfluorosulfonic acid polymers. The polyimide containing 20 mol % 1,5‐naphthylene moieties showed higher proton conductivity (0.3 S cm^?1) at 120 °C and 100% relative humidity than perfluorosulfonic acid polymers. The temperature and humidity dependence of the proton conductivity was examined. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3901–3907, 2003     

Synthesis and characterization of SPE membrane based on sulfonated FEP‐g‐acrylic acid by radiation induced graft copolymerization for PEM fuel cell

A Novel solid polymer electrolyte (SPE) membrane containing both ? COOH and ? SO₃H group has been prepared by simultaneous method of radiation grafting of acrylic acid onto FEP followed by sulfonation. The presence of weakly acidic acrylic acid controls the swelling in water while ? SO₃H group provides conductivity due to its strongly ionic characteristic. FEP‐g‐acrylic acid and its sulfonated derivatives were characterized by their properties. While the mechanical properties decreased, other properties such as ion exchange capacity (IEC), water uptake and ionic conductivity increased with increase in graft content. These properties further changed on sulfonation. Acrylic acid being weakly acidic in nature, conductivity values of the grafted membrane were quite low. However, introduction of strong ? SO₃H group resulted in conductivity closer to Nafion 117. Few sulfonated membranes have been tested with respect to H₂/O₂ fuel cell performance. Short‐term fuel cell test for 100 hr gave a stable performance. These membranes are less expensive compared to Nafion. Copyright © 2004 John Wiley & Sons, Ltd.     

Poly(ether ketone)s bearing pendent sulfonate groups via copolyacylation of a sulfonated monomer and isomeric AB‐type comonomers

Poly(ether ketone)s bearing pendent sulfonate groups (SPEK‐x/y/z) have been successfully synthesized via copolyacylation of a presulfonated monomer SBP and two isomeric AB‐type self‐condensable comonomers, that is, 4‐phenoxybenzoic acid (p‐POBA) and 3‐phenoxybenzoic acid (m‐POBA). Proton‐exchange membranes (PEMs) with precisely controlled ion‐exchange capacity (IEC) and high strength can be readily prepared from these ionomers. PEMs prepared from p‐POBA other than m‐POBA exhibit much higher dimensional stability and proton conductivity at elevated temperature above 60 °C, showing prominent isomeric (para vs. meta) effects of polymer structural units. Furthermore, properties of PEMs prepared from p‐POBA are optimized by tuning IEC. SPEK‐1.0/2.2/0 with an IEC of 1.84 mmol g^?1 exhibits acceptable swelling, much higher proton conductivity, and lower methanol permeability than commercial Nafion 115, implying potential application in direct methanol fuel cells. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 200–207     

Preparation and characterization of polyfuran/poly(2‐fluoroaniline) conducting composites

This article deals with the chemical synthesis and characterization of poly(2‐fluoroaniline) (P2FAn) and polyfuran (PFu) homopolymers and PFu/P2FAn and P2FAn/PFu composites. P2FAn and PFu homopolymers were synthesized using ammonium persulfate and antimony (III) chloride as catalyst, respectively. These homopolymers and composites were studied in the doped state using Fourier transform infrared spectroscopy and ultraviolet–visible absorption spectroscopy, thermogravimetric analysis, scanning electron microscopy, four‐probe conductivity technique, and Gouy Scale measurements. PFu/P2FAn and P2FAn/PFu composites were found to possess different thermal, conductivity, electronic, and morphological properties from each other when synthesis order of guest and host polymers was varied. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3359–3367, 2004     

Phase‐separated,conducting composites from polyaniline and benzobisthiazole rigid‐rod polymer

As an alternative method for processing polyaniline (PANI) from its conducting (protonated) state, vacuum casting of PANI from a methanesulfonic acid (MSA) solution provided films with electrical conductivity values of about 130–150 S/cm. In addition, we similarly prepared blended films of PANI · MSA and poly(p‐phenylene benzobisthiazole) (PBZT). This process eliminated the need for a subsequent protonation step and had the additional advantage that the conjugated PBZT may provide alternative conducting pathways. Conductivity values of the composite films ranged from 100 pS/cm to 124 S/cm, and the films displayed critical concentration behavior with a PANI threshold concentration of 2.75% and a critical exponent of 4. Transmission electron micrographs displayed phase‐separated regions with PANI forming a continuous network at high concentrations. Thermogravimetric analysis results demonstrated the thermal and thermooxidative stability advantage of the blends due to the PBZT component. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2539–2548, 2001