Double responsive copolymer hydrogels prepared by frontal polymerization

Frontal polymerization was successfully used to synthesize copolymer hydrogels of poly(N‐vinylcaprolactam‐co‐itaconic acid). All materials were characterized by response to stimuli (pH and/or temperature), depending on the itaconic acid content. Namely, relatively low amounts of this latter were found to be crucial for determining the degree of swelling. In particular, hydrogels behave differently if swollen at pH values that are higher or lower of 7–8, and exhibit temperature response as well (lower critical solution temperature at ca. 30 °C), which makes these materials potentially interesting for biomedical applications. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2166–2170     

Polymer hydrogels of 2‐hydroxyethyl acrylate and acrylic acid obtained by frontal polymerization

In this work, we report on the synthesis and characterization of homopolymers and copolymers of acrylic acid and 2‐hydroxyethyl acrylate prepared by the use of the frontal polymerization (FP) technique. Tetraethyleneglycoldiacrylate was used as a crosslinker and benzoyl peroxide as an initiator. The maximum temperatures reached by the front were in the range between 214 °C and 296 °C. Besides, front velocities ranged between 3.9 and 10.8 cm/min, the latter being one of the highest values reported so far in the FP literature. Differential scanning calorimetry was used to estimate the conversion degree, which was always comprised between 90% and 96%, and to determine the glass transition temperatures, which were found to be dependent on the composition, with values ranging from 13 °C to 168 °C. Moreover, the obtained materials were allowed to swell in aqueous solutions at various pH. The samples exhibit a moderate increase of the swelling ratio percentage (SR%) at pH ≈ 5–6, and a sudden and larger SR% increase at pH ≈ 12–13 depending on the composition, thus indicating the obtainment of pH‐responsive polymer hydrogels. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Thermoresponsive super water absorbent hydrogels prepared by frontal polymerization

Frontal polymerization was used as an alternative technique for the preparation of super water absorbent hydrogels obtained from acrylamide and 3‐sulfopropyl acrylate, potassium salt (SPAK) in the presence of N,N′‐methylene‐bisacrylamide as a crosslinker. All samples were synthesized in dimethyl sulfoxide, and their swelling behavior in water was investigated. It was found that their features are dependent on the monomer ratio used, which influenced the porous morphology, and consequently, the swelling capability. The swelling ratio ranges from about 1000% for the acrylamide homopolymer up to 14,000% for the sample containing 87.5 mol % of SPAK, thus indicating that this parameter can be easily tuned by using the appropriate monomer ratio. The affinity towards water was eventually confirmed by contact angle analysis. Polymer hydrogels made from at least 62.5 mol % SPAK exhibit a thermoresponsive behavior, with a lower critical solution temperature of ～30 °C. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2486–2490, 2010     

Dual responsive poly(N‐isopropylacrylamide) hydrogels having spironaphthoxazines as pendant groups

Stimuli responsive hydrogels (PNIPAAm‐MSp) with a thermoresponsive backbone and photochromic pendant groups were synthesized via free radical polymerization using N‐isopropylacrylamide, modified spironaphthoxazines with a polymerizable double bond (MSp) as photochromic monomer, the crosslinker N,N′‐methylenebis(acrylamide) and the initiator 2,2′‐azobis(isobutyronitrile) in dimethylsulfoxide. The polymers are dual responsive, in that poly(N‐isopropylacrylamide) (PNIPAAm) responds to temperature changes whereas the pendant spironaphthoxazines respond to light. Irradiation enhanced the water absorption of the polymers while increases in temperature decreased it. The irradiated PNIPAAm‐MSp showed best water absorption at 0 °C (Q = 3.25) while water desorbed at higher temperatures (35 °C; Q = 0.30); where Q is the amount of water absorbed by a gram of dry polymer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3318–3325, 2009     

Synthesis and characterization of graphene‐containing thermoresponsive nanocomposite hydrogels of poly(N‐vinylcaprolactam) prepared by frontal polymerization

Thermoresponsive poly(N‐vinylcaprolactam) nanocomposite hydrogels containing graphene were successfully prepared by frontal polymerization. High concentration of graphene (5.0 mg/mL) was obtained by direct graphite sonication in the self‐same liquid monomer, thus avoiding any chemical manipulation and obtaining “real” graphene as nanofiller instead of one of its more or less oxidized derivative, which is what generally reported in published reports. Furthermore, the corresponding nanocomposites were obtained without using any solvent to be eventually removed. The materials were fully characterized by RAMAN, SEM, and TEM, and their swelling behavior and rheological properties were investigated. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

A facile pathway for the fast synthesis of colloidal crystal‐loaded hydrogels via frontal polymerization

In this work, a dually sensitive colloidal crystal (CC)‐loaded hydrogel has been synthesized via frontal polymerization (FP) in a facile and rapid way. First, a polystyrene CC film was fabricated by vertical deposition on the inner wall of a test tube. Then, a mixture of acrylic acid (AAc), 2‐hydroxyethyl methacrylate (HEMA), and glycerol along with the initiator and crosslinker was added to this test tube to carry out FP, resulting in the formation of CC‐loaded hydrogel. The influence of the mass ratios of HEMA/AAc on front velocity and temperatures were studied. The swelling behavior, the morphology, and the stimuli‐responsive behavior of the CC‐loaded hydrogels prepared via FP were thoroughly investigated on the basis of swelling measurement, scanning electron microscopy, and reflection spectra. Results show that the as‐prepared CC‐loaded hydrogels exhibit excellent dual sensitivity to both methanol concentrations and pH values with very short response time, which can be observed visually without the aid of instruments. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Stimuli‐responsive buckling mechanics of polymer films

Thin polymer films may undergo a wide variety of elastic instabilities that include global buckling modes, wrinkling and creasing of surfaces, and snapping transitions. Traditionally, these deformations have usually been avoided as they often represent a means of mechanical failure. However, a new trend has emerged in recent years in which buckling mechanics can be harnessed to endow materials with beneficial functions. For many such applications, it is desirable that such deformations happen reversibly and in response to well‐defined signals or changes in their environment. While significant progress has been made on understanding and exploiting each type of deformation in its own right, here we focus on recent advances in the control and application of stimuli‐responsive mechanical instabilities. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1441–1461     

Synthesis of stimuli‐responsive macroazoinitiators and their use as an inistab toward hairy polymer latex particles

Stimuli‐responsive macroazoinitiators with central azo unit have been synthesized by atom transfer radical polymerization (ATRP) of 2‐(dimethylamino)ethyl methacrylate or 2‐(diethylamino)ethyl methacrylate in 2‐propanol at 25 °C. The mean degree of polymerization of the polymer chains besides the azo group was fixed between 25 and 60. ¹H NMR, gel permeation chromatography, UV‐Vis spectrophotometer, and surface tensiometer were used to characterize the stimuli‐responsive macroazoinitiators in terms of their chemical structure, molecular weight, polydispersity, and pH‐responsive behavior, respectively. Eventually, dispersion polymerization of styrene using the poly[2‐(diethylamino)ethyl methacrylate] (PDEA) macroazoinitiator as an inistab (initiator + stabilizer) in 2‐propanol medium was conducted. Near‐monodisperse 98 nm polystyrene (PS) latex particles with pH‐responsive PDEA hair were successfully synthesized. The PS latex particles with the PDEA hair can be dispersed in acidic aqueous media where the PDEA hair was protonated and was solvated, and can be flocculated in basic aqueous media where the PDEA hair was deprotonated and was precipitated. This dispersion‐flocculation cycle was reversible. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3431–3443, 2009     

Structural design of stimuli‐responsive bioconjugated hydrogels that respond to a target antigen

Stimuli‐responsive bioconjugated hydrogels that can respond to a target antigen (antigen‐responsive hydrogels) were prepared by introducing antigen‐antibody bindings as reversible crosslinks into the gel networks. The preparation conditions of the antigen‐responsive hydrogels and the mechanism of the antigen‐responsive behavior were investigated, focusing on bioconjugated hydrogel structures. This article also focuses on the effect of semi‐interpenetrating polymer network (semi‐IPN) structures on the antigen‐responsive swelling/shrinking behavior of bioconjugated hydrogels with antigen‐antibody bindings. The preparation conditions and the network structures of the bioconjugated hydrogels are discussed in relation to designing antigen‐responsive hydrogels. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2144–2157, 2009     

3‐D Interdigitated electrodes for uniform stimulation of electro‐responsive hydrogels for biomedical applications

Stimuli‐responsive hydrogels are continuing to increase in demand in biomedical applications. Occluding a blood vessel is one possible application which is ideal for a hydrogel because of their ability to expand in a fluid environment. However, typically stimuli‐responsive hydrogels focus on bending instead of radial uniform expansion, which is required for an occlusion application. This article focuses on using an interdigitated electrode device to stimulate an electro‐responsive hydrogel in order to demonstrate a uniform swelling/deswelling of the hydrogel. A Pluronic‐bismethacrylate (PF127‐BMA) hydrogel modified with hydrolyzed methacrylic acid, in order to make it electrically responsive, is used in this article. An interdigitated electrode device was manufactured containing Platinum electrodes. The results in this paper show that the electrically biased hydrogels deswelled 230% more than the non‐biased samples on average. The hydrogels deswelled uniformly and showed no visual deformations due to the electrical bias. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1523–1528     

Stimuli‐Responsive Semi‐Fluorinated Polymer Brushes on Porous Silica Substrates

Summary: A diblock copolymer brush consisting of poly(methyl acrylate)‐block‐poly(pentafluoropropyl acrylate) (Si/SiO₂//PMA‐b‐PPFA) was synthesized on a porous silica substrate. The brush was exposed to selective solvents, as well as thermal treatments, to induce a surface rearrangement. The rearrangement resulted in the selective loss or creation of an ultrahydrophobic layer by location of the fluoropolymer segment. This work demonstrates that surface rearrangements observed on flat surfaces can be transferred to porous substrates.

Image of a water droplet in contact with an Si/SiO₂//PMA‐b‐PPFA ultrahydrophobic polymer brush, synthesized from a porous silica substrate.     

Stimulus‐responsive polymers based on 2‐hydroxypropyl acrylate prepared by RAFT polymerization

Homopolymerization and diblock copolymerization of 2‐hydroxypropyl acrylate (HPA) has been conducted using reversible addition fragmentation chain transfer (RAFT) chemistry in tert‐butanol at 80 °C. PHPA homopolymers were obtained with high conversions and narrow molecular weight distributions over a wide range of target degrees of polymerization. Like its poly(2‐hydroxyethyl methacrylate) isomer, PHPA homopolymer exhibits inverse temperature solubility in dilute aqueous solution, with cloud points increasing systematically on lowering the mean chain length. The nature of the end groups is shown to significantly affect the cloud point, whereas no effect of concentration was observed over the PHPA concentration range investigated. Various thermoresponsive PHPA‐based diblock copolymers were prepared via one‐pot syntheses in which the second block was either permanently hydrophilic or pH‐responsive. Preliminary studies confirmed that poly(ethylene oxide)‐poly(2‐hydroxypropyl acrylate) (PEO₄₅‐PHPA₄₈) and poly(2‐hydroxypropyl acrylate)‐ poly(2‐hydroxyethyl acrylate) (PHPA₄₉‐PHEA₆₈)diblock copolymers formed well‐defined PHPA‐core micelles in 10 mM sodium nitrate solution at 40 °C and 70 °C with mean hydrodynamic diameters of 20 nm and 35 nm, respectively. In contrast, most other PHPA‐based diblock copolymers investigated formed larger colloidal aggregates in 10 mM NaNO₃ solution at elevated temperatures. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2032–2043, 2010     

Stimuli‐responsive brush‐shaped conjugated polymers with pendant well‐defined poly(vinyl ether)s

For the synthesis of brush‐shaped conjugated polymers consisting of a poly(phenylene butadiynylene) backbone and well‐defined poly(vinyl ether) (polyVE) side chains, we designed polyVE‐based macromonomers bearing a diethynyl benzene group at the terminus and applied them to the grafting through synthesis. The macromonomer (DE‐PIBVE) was synthesized by living cationic polymerization of isobutyl VE (IBVE) using a functionalized initiator (TMS‐DEVE‐TFA) having a TMS protected diethynyl benzene moiety, followed by deprotection of the TMS groups. As a result, we succeeded in the synthesis of the target brush‐shaped conjugated polymers [poly(DE‐PIBVE)] by oxidative coupling reaction of the diethynyl benzene groups. We found that the solution of poly(DE‐PIBVE) with a specific side chain length exhibited solvatochromism and thermochromism depending on the polarity of the media employed. This phenomenon was attributed to self‐assembly in polar media due to the intermolecular π–π interaction between neighboring conjugated polymer backbones, where the self‐assembly behavior would be closely related to the pendant polyVE structure. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3318–3325     

Synthesis and physicochemical characterization of biodegradable and pH‐responsive hydrogels based on polyphosphoester for protein delivery

In this work, a series of biodegradable and pH‐responsive hydrogels based on polyphosphoester and poly(acrylic acid) are presented. A novel biodegradable macrocrosslinker α‐methacryloyloxyethyl ω‐acryloyl poly(ethyl ethylene phosphate) (HEMA‐PEOP‐Ac) was synthesized by first ring‐opening polymerization of the cyclic monomer 2‐ethoxy‐2‐oxo‐1,3,2‐dioxaphospholane using HEMA as the initiator and Sn(Oct)₂ as catalyst, and subsequent conversion of hydroxyl into vinyl group. The hydrogels were then fabricated by the copolymerization of the macromonomer with acrylic acid, and their swelling/deswelling and degradation behaviors were investigated. The results demonstrated that the crosslinking density and pH values of media strongly influenced both the swelling ratio and the degradation rate of the hydrogels. The rheological properties of these hydrogels were also studied from which the storage modulus (G′) showed clear dependence on the crosslinking density. MTT and “live/dead” assay showed that these hydrogels were compatible to fibroblast cells, not exhibiting apparent cytotoxicity even at high concentrations. Moreover, in vitro bovine serum albumin release from these hydrogels was also investigated, and it could be found that the release profiles showed a burst effect followed by a continuous release phase, and the release rate was inversely proportional to the crosslinking density of hydrogels. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1919–1930, 2010     

Thermoresponsive super water absorbent hydrogels prepared by frontal polymerization of N‐isopropyl acrylamide and 3‐sulfopropyl acrylate potassium salt

Super water absorbent polymer hydrogels were synthesized by frontal polymerization. These materials were obtained by copolymerizing N‐isopropyl acrylamide (NIPAAm) and 3‐sulfopropyl acrylate potassium salt (SPAK) in the presence of N,N′‐methylene‐bis‐acrylamide as a crosslinker. It was found that their swelling behavior in water can be easily tuned by using either the appropriate monomer ratio or the amount of the crosslinker used. Namely, the swelling ratio was found to range from about 1000% for the NIPAAm homopolymer in the presence of 5.0 mol % of crosslinker, up to 35,000% for the sample containing 87.5 mol % of SPAK and 1.0 mol % of crosslinker. The affinity toward water was also confirmed by contact angle analysis. Moreover, the obtained hydrogels exhibit a thermoresponsive behavior, with a lower critical solution temperature of about 28–30 °C. This value is close to that of poly(NIPAAm) but with a swelling capability that dramatically increases as the amount of SPAK increases. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of thermo‐responsive poly(N‐vinylcaprolactam)‐containing block copolymers by cobalt‐mediated radical polymerization

Thermo‐responsive block copolymers based on poly(N‐vinylcaprolactam) (PNVCL) have been prepared by cobalt‐mediated radical polymerization (CMRP) for the first time. The homopolymerization of NVCL was controlled by bis(acetylacetonato)cobalt(II) and a molecular weight as high as 46,000 g/mol could be reached with a low polydispersity. The polymerization of NVCL was also initiated from a poly(vinyl acetate)‐Co(acac)₂ (PVAc‐Co(acac)₂) macroinitiator to yield well‐defined PVAc‐b‐PNVCL block copolymers with a low polydispersity (M_w/M_n = 1.1) up to high molecular weights (M_n = 87,000 g/mol), which constitutes a significant improvement over other techniques. The amphiphilic PVAc‐b‐PNVCL copolymers were hydrolyzed into unprecedented double hydrophilic poly(vinyl alcohol)‐b‐PNVCL (PVOH‐b‐PNVCL) copolymers and their temperature‐dependent solution behavior was studied by turbidimetry and dynamic light scattering. Finally, the so‐called cobalt‐mediated radical coupling (CMRC) reaction was implemented to PVAc‐b‐PNVCL‐Co(acac)₂ precursors to yield novel PVAc‐b‐PNVCL‐b‐PVAc symmetrical triblock copolymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of Poly(2‐oxazoline)‐Based Hydrogels with Tailor‐Made Swelling Degrees Capable of Stimuli‐Triggered Compound Release

A 32‐membered library of poly(2‐oxazoline)‐based hydrogels of the composition p EtOx _m‐p PhOx _n‐p PBO _q (m/n = 150/0, 100/50, 50/100, and 0/150; q = 1.5–30) was prepared from 2‐ethyl‐ ( EtOx ), 2‐phenyl‐2‐oxazoline ( PhOx ), and phenylene‐1,3‐bis‐(2‐oxazoline) ( PBO ). The polymerizations were performed from ground monomer mixtures at 140 °C in a single‐mode microwave reactor in reaction times as short as 1 h. Purified hydrogels, containing no residual monomers, were obtained in yields of 95% or higher. Acid‐mediated hydrolysis rates as well as swelling degrees of the hydrogels were adjustable over a broad range; swelling degrees in water/ethanol/dichloromethane ranged from 0 to 13.8/11.7/20.0. The hydrogels could incorporate organic molecules according to in situ or post‐synthetic routines. Post‐synthetic routines enabled for the preparation of hydrogels from which the incorporated compounds were only released through diffusion processes if the solvent was changed or through hydrogel degradation if the pH was lowered.     

A “self‐pinning” adhesive based on responsive surface wrinkles

Surface wrinkles are interesting since they form spontaneously into well‐defined patterns. The mechanism of formation is well‐studied and is associated with the development of a critical compressive stress that induces the elastic instability. In this work, we demonstrate surface wrinkles that dynamically change in response to a stimulus can improve interfacial adhesion with a hydrogel surface through the dynamic evolution of the wrinkle morphology. We observe that this control is related to the local pinning of the crack separation pathway facilitated by the surface wrinkles during debonding, which is dependent on the contact time with the hydrogel. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Dual stimuli‐responsive polyamines derived from modified N‐vinylpyrrolidones through CuAAC click chemistry

The synthesis via copper(I)‐catalyzed azide alkyne cycloaddition (CuAAC) of three new monomer derivatives of N‐vinyl‐2‐pyrrolidone (VP) carrying cyclic pyrrolidine, piperidine, and piperazine groups and the corresponding copolymers with unmodified VP is shown. The systems bearing pyrrolidine and piperidine displayed both thermo‐ and pH‐response, which has not been reported previously for a polymer with polyvinylpyrrolidone (PVP) backbone. A broad modulation of the LCST with the copolymer composition and pH was observed in a temperature range 0–100 °C. The polymers carrying piperazine exhibited broad buffering regions and no thermosensitivity. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1098–1108