Humic acid‐derived hierarchical porous carbon preparation using vacuum freeze‐drying for electric double layer capacitors

Electric double layer capacitors (EDLCs) preserve charge by reversible physisorption of electrolyte ions on the surface of porous active materials. Therefore, engineering a reasonable pore structure and reducing oxygen‐containing groups of carbon materials are efficient approaches to enable rapid ion diffusion pathways and long life span, respectively. Here, humic acid (HA)‐derived hierarchical porous carbon was fabricated by vacuum freeze‐drying, KOH activation, and subsequent annealing. The macropores were generated from the vacancies where the ice crystals in the HA–KOH gels initially occupied during vacuum‐freeze drying, while abundant micropores were created from homogeneous KOH activation. In addition, subsequent annealing further reduced the oxygen‐containing groups. When used as EDLC electrodes in 1 mol/L TEABF₄/PC organic electrolyte, they could give a high capacitance of 150 F/g at 0.05 A/g and excellent rate performance of 81% (with capacitance of 121.46 F/g at 10 A/g). More importantly, the hierarchical porous carbon displays superior capacity retention of 85.6% after 10,000 cycles at 1 A/g at 2.7 V.     

A novel freeze‐dried storage and preparation method for the determination of mycophenolic acid in plasma by high‐performance liquid chromatography

Plasma samples were conventionally stored at freezing conditions until the time of detection. Such a technique, when carried out over an extended period, is energy consuming; in addition, preparation and transportation of stored samples is inconvenient. In this study, a freeze‐dried storage and preparation method was proposed to determine the presence of mycophenolic acid (MPA) in plasma. Fresh plasma samples were freeze‐dried using a device, and then stored at ambient temperature. After the stored samples were soaked with methanol spiked with the internal standard, high‐performance liquid chromatography was conducted to detect MPA. The proposed method was demonstrated to be precise and accurate over the linear range of 0.5–50 μg mL⁻¹, with both intra‐ and inter‐day precision being <7% and biases <10%. The freeze‐dried samples were stable at ambient temperature for at least 40 days. This method was also successfully applied to the pharmacokinetic study of MPA in healthy volunteers. Pharmacokinetic parameters, such as maximum plasma concentration, time point of maximum plasma concentration and elimination half‐life, among others, were consistent with the results in the published study. This proposed technique was proved to be simple, reproducible and energy saving. This approach could also simplify the storage and analysis of samples in clinical and scientific drug research.     

Rapid Detection of Serum Procalcitonin by Immunochromatograghy Technology Based on Freeze‐dried Up‐conversion Nanoparticles/Antibody Conjugates

Procalcitonin (PCT) is a sensitive and specific biomarker for sepsis diagnosis and widely used as a biomarker to improve the diagnosis of bacterial infections and to guide the antibiotic therapy. In our work, an improved up‐converting nanoparticle (UCP) technology based on the immunochromatographic assay (UPT‐ICA) was developed for rapid and quantitative detection of PCT. In order to further improve the accuracy, sensitivity and stability of the assay on the basis of our previous study, the UCP coupling with monoclonal antibody of PCT (UCP‐Ab1) was freeze‐dried under certain conditions. And the detections of PCT levels with UCP‐Ab1 conjugates before and after freeze‐drying were evaluated. The results show that, compared to the UCP‐Ab1 conjugates without freeze‐drying, the detection sensitivity of freeze‐dried UCP‐Ab1 is slightly improved, having a lower immunochromatogragh background and better stability. This improved method can provide a rapid, accurate, and relatively easy way for the clinical detection of PCT.     

Differential scanning calorimetry study on thermal behaviors of freeze‐dried poly(L‐lactide) from dilute solutions

Glass transition, cold crystallization, and melting of freeze‐dried poly(L‐lactide) (PLLA) prepared from dilute 1,4‐dioxane solutions were investigated by differential scanning calorimetry (DSC). Conventional DSC measurements of heating scans revealed that freeze‐dried PLLA prepared from a 0.07 wt % solution undergoes a two‐step cold crystallization (or reorganization) with a lower exotherm appearing at about 78 °C and with a higher broad exotherm between 110–155 °C. The peak temperature of the former exotherm is about 50 K lower than that observed for a reference bulk sample. Step‐scan mode DSC, which provides information essentially equivalent to that obtained from the temperature‐modulated DSC, revealed that the glass‐transition temperature is about 6 K lower than that of the reference bulk. These findings suggest enhanced chain mobility for freeze‐dried PLLA. Freeze‐dried PLLA that crystallized at 80 °C for 40 min was revealed to contain a rather large amount of rigid amorphous material (42%). © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 115–124, 2005     

Freeze‐Drying‐Assisted Synthesis of Hierarchically Porous Carbon/Germanium Hybrid for High‐Efficiency Lithium‐Ion Batteries

Herein, an approach is reported to prepare porous a carbon/Ge (C/Ge) hybrid. In this hybrid, Ge nanoparticles are closely embedded in a highly conductive and flexible carbon matrix. Such a hybrid features a high surface area (128.0 m² g^?1) and a hierarchical micropore–mesopore structure. When used as an anode material in lithium‐ion batteries (LIBs), the as‐prepared hybrid [C/Ge (60.37 %)] exhibits an improved lithium storage performance with regard to its capacity and rate capability compared to its counterparts. More specifically, it can maintain a specific capacity as high as 906 mAh g^?1 at a high current density of 0.6 A g^?1 after 50 cycles. The excellent lithium storage performance of the C/Ge (60.37 %) sample can be attributed to synergetic effects between the carbon matrix and Ge nanoparticles. The method we adopted is simple and effective, and can be extended to fabricate other nanomaterials.     

Temperature‐induced solid‐to‐solid transformation in helical homochiral coordination polymers

The reactions of (R)‐ and (S)‐4‐(1‐carboxyethoxy)benzoic acid (H₂CBA) with 1,3‐bis(2‐methyl‐1H‐imidazol‐1‐yl)benzene (1,3‐BMIB) ligands afforded a pair of homochiral coordination polymers (CPs), namely, poly[[[μ‐1,3‐bis(2‐methyl‐1H‐imidazol‐1‐yl)benzene][μ‐(S)‐4‐(1‐carboxylatoethoxy)benzoato]zinc(II)] monohydrate], {[Zn(C₁₀H₈O₅)(C₁₄H₁₄N₄)]·H₂O}_n or {[Zn{(S)‐CBA}(1,3‐BMIB)]·H₂O}_n ( 1‐L ), and poly[[[μ‐1,3‐bis(2‐methyl‐1H‐imidazol‐1‐yl)benzene][μ‐(R)‐4‐(1‐carboxylatoethoxy)benzoato]zinc(II)] monohydrate] ( 1‐D ). Three kinds of helical chains exist in compounds 1‐D and 1‐L , which are constructed from Zn^II atoms, 1,3‐BMIB ligands and/or CBA^2? ligands. When the as‐synthesized crystals of 1‐L and 1‐D were further heated in the mother liquor or air, poly[[μ‐1,3‐bis(2‐methyl‐1H‐imidazol‐1‐yl)benzene][μ‐(S)‐4‐(1‐carboxylatoethoxy)benzoato]zinc(II)], [Zn(C₁₀H₈O₅)(C₁₄H₁₄N₄)]_n or [Zn{(S)‐CBA}(1,3‐BMIB)]_n ( 2‐L ), and poly[[μ‐1,3‐bis(2‐methyl‐1H‐imidazol‐1‐yl)benzene][μ‐(R)‐4‐(1‐carboxylatoethoxy)benzoato]zinc(II)] ( 2‐D ) were obtained, respectively. The single‐crystal structure analysis revealed that 2‐L and 2‐D only contained one type of helical chain formed by Zn^II atoms and 1,3‐BMIB and CBA^2? ligands, which indicated that the helical chains were reconstructed though solid‐to‐solid transformation. This result not only means the realization of helical transformation, but also gives a feasible strategy to build homochiral CPs.     

Polyamide‐6/natural clay mineral nanocomposites prepared by solid‐state shear milling using pan‐mill equipment

The polyamide‐6 (PA6)/natural clay mineral nanocomposites were successfully prepared by solid‐state shear milling method without any treatment of clay mineral and additives. PA6/clay mixture was pan‐milled to produce PA6/clay compounding powder, using pan‐mill equipment. The obtained powder as master batch was diluted with neat PA6 to prepare composites by a twin‐screw extruder. The clay silicate layers were found to be partially exfoliated and dispersed homogeneously at nanometer level in PA6 matrix. The rheological measurements and mechanical properties of nanocomposites were characterized. The shear viscosities of nanocomposites were higher than that of pure PA6, and tensile strength and tensile modulus increased, but Izod impact strength decreased, with increasing concentration of clay. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 249–255, 2006     

Studies on target tissue distribution of ginsenosides and epimedium flavonoids in rats after intravenous administration of Jiweiling freeze‐dried powder

A simple and rapid liquid chromatography–mass spectrometry (LC‐MS) method was developed and validated for analysis of ginsenoside Rb₁, Rb₂, Rc, Rd, Re, Rf, Rg₁, icariin and epimedin A, B, C in rat target tissues (spinal cord, brain, muscle and sciatic nerve) after intravenous administration of Jiweiling freeze‐dried powder using genistein as an internal standard (IS). The tissue samples were treated by protein precipitation with methanol prior to HPLC and chromatographic separation was performed on a C₁₈ column utilizing a gradient elution program with acetonitrile and 0.1% formic acid aqueous. Electrospray ionization (ESI) source was employed and the 11 analytes and IS were detected by multiple reaction monitoring (MRM) scanning under the negative ionization mode. Higher sensitivity was achieved and the optimized mass transition ion‐pairs (m/z) for quantitation were selected. The calibration curves were linear over the investigated concentration ranges with correlation coefficients higher than 0.995. The intra‐ and inter‐day RSDs were all less than 10% with the relative error (RE) within ±9.3%. The mean extraction recoveries for all compounds were between 93.3 and 106%. The proposed method was successfully applied to investigate the target tissue distribution of the 11 compounds in rat after intravenous administration of Jiweiling freeze‐dried powder. Copyright © 2011 John Wiley & Sons, Ltd.     

Automated determination of venlafaxine in human plasma by on‐line SPE‐LC‐MS/MS. Application to a bioequivalence study

A new automated SPE‐LC‐ESI‐MS/MS method was developed and validated to quantify venlafaxine in human plasma using fluoxetine as an internal standard. The analytes were automatically extracted from plasma by C18 SPE cartridges, separated on a C8 RP column and analyzed by MS in the multiple reaction‐monitoring (MRM) mode. The method has a chromatographic run time of 4.0 min and a linear calibration curve over the range of 0.25–200 ng/mL (r >0.997). The between‐run precisions, based on the percent RSD for replicate quality controls (0.75; 80, and 200 ng/mL), were < 8.5% for all concentrations. The between‐run accuracies, based on the percent relative error, were < 4.0%. This method was successfully employed in a bioequivalence study of two venlafaxine capsule formulations (test formulation from Eurofarma (Brazil) and Efexor XR, reference formulation, from Wyeth‐Whitehall, Brazil) in 48 healthy volunteers of both sexes who received a single 150 mg dose of each formulation. More than 3000 samples were analyzed eliminating the analyst's exposure to hazardous organic solvents normally employed in off‐line liquid–liquid extractions. The 90% confidence interval (CI) of the individual ratio geometric mean for Test/Reference was 91.6–103.4% for AUC_{0–48 h} and 102.2–112.6% for C_max. Since both 90% CI for AUC_{0–48 h} and C_max were included in the 80–125% interval proposed by the US Food and Drug Administration (FDA) and the Brazilian National Health Surveillance Agency (ANVISA), the test formulation was considered bioequivalent to Efexor XR according to both the rate and extent of absorption.     

Partially renewable copolyesters prepared from acetalized d‐glucitol by solid‐state modification of poly(butylene terephthalate)

The backbone of poly(butylene terephthalate) (PBT) was modified with 2,4:3,5‐di‐O‐methylene‐D ‐glucitol (Glux) using solid‐state modification (SSM). The obtained copolyesters proved to have a non‐random overall chemical microstructure. The thermal properties of these semicrystalline, block‐like, Glux‐based materials were extraordinary, showing higher melting points, and glass transition temperatures compared with other sugar‐based copolyesters prepared by SSM. These remarkable thermal properties were a direct result of the inherently rigid structure of Glux and the relatively slow randomization of the block‐like chemical microstructure of the Glux‐based copolyesters in the melt. SSM proved to be a versatile tool for preparing partially biobased copolyesters with superior thermal properties. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 164–177     

Determination of Cd, Co, Cr, Cu, Fe, Mn, Ni and Pb in natural waters, alkali and alkaline earth salts by electrothermal atomic absorption spectrometry after preconcentration by column solid phase extraction

Methods are described for the determination of trace and ultra trace amounts of Cd, Co, Cr, Cu, Fe, Mn, Ni and Pb in natural waters, alkali and alkaline earth salts. Separation and preconcentration of trace metals is achieved by a column solid phase extraction procedure using silica gel modified with derivatives of dithiocarbamates — Na-DDTC (sodium diethyldithio-carbamate and HMDTC (ammonium hexamethylene-dithiocarbamate) as column packing material. The influence of the sorbent preparation procedure on the degree of sorption of the trace analytes is examined for different pH values of the sample solution. Isobutylmethyl ketone (IBMK) is proposed as an effective eluent for quantitative elution of retained metal ions. Optimal instrumental parameters for ETAAS determination of preconcentrated elements in organic eluate are presented. Practical application of sorbents in analysis of natural waters and alkali and alkaline earth salts is demonstrated. Proposed preconcentration procedure combined with ETAAS determination of trace analytes allows the determination of 0.04 g l^–1 Cd, 0.1 g l^–1 Cr, Cu, and Mn and 0.3 g l^–1 Co, Fe, Ni and Pb in natural waters and 1.10^–7% Cd, 3.10^–7% Cr and Mn, 7.10^–7% Co, Ni and Pb and 2.10^–6% Cu and Fe in alkali and alkaline earth salts.     

New apparatus for the in-situ observation of a freeze drying process

This work presents the performances of a new apparatus developed for thein-situ observation of a freeze drying (lyophilization) phenomenon. The results obtained on the lyophilization kinetics performed on a standard mixture (aqueous saturated NaCl solution) are presented.     

Analytical evaluation of pseudopotential matrix elements with Gaussian‐type solid harmonics of arbitrary angular momentum

An efficient formalism for evaluating pseudopotential matrix elements with Gaussian‐type solid harmonics of arbitrary angular momentum is presented. It is based on the tensor coupling technique, which is especially well suited for treating Gaussian‐type solid harmonics of arbitrary angular momentum. Closed analytical expressions are derived for the matrix elements as well as for their nuclear displacement derivatives. The efficiency of the implementation into our new parallel density functional program PARA GAUSS and the quality of the pseudopotential approach is tested for a set of representative molecules and cluster models. To this end the results of pseudopotential calculations are compared to those of nonrelativistic and scalar‐relativistic all‐electron calculations. © 2000 John Wiley & Sons, Inc. Int J Quant Chem 79: 209–221, 2000     

Rapid Determination of the Antioxidant Capacity of Lettuce by an E‐Tongue Based on Flow Injection Coulometry

This work proposes the use of an electronic tongue based on flow injection coulometry for the rapid determination of the antioxidant capacity of fresh lettuce. The e‐tongue consisted of a series of 16 porous carbon electrodes, each poised at a fixed potential from +100 to +850 mV. Each injection leaded to a characteristic hydrodynamic voltammogram, whose profile reflects the composition of antioxidants. The correlation between the peak area recorded by each sensor and the 1,1‐Diphenyl‐2‐picryl‐hydrazyl (DPPH) assay was maximum ín the range of potentials between +400 and 750 mV (R2>0.97). Accordingly, the charge measured provided a direct and simple index of the antioxidant capacity. The practical utility of such index was initially demonstrated by determining the best extraction conditions. This consisted in freeze‐drying of lettuce followed by methanolic extraction. Later, the e‐tongue was used to evaluate the effect of storage (one week at 5 °C) on lettuce. The e‐tongue revealed that lettuce lost up to 25 % of their initial antioxidant activity during storage. However, when lettuce samples were pre‐treated with fast cooling or vacuum cooling, the decrease of the antioxidant index was limited to 14 and 15 %. Overall, the e‐tongue is a rapid, simple and sensitive method for the determination of the antioxidant capacity of fresh lettuce samples. Indirectly, these findings suggest also that lettuce may serve as potential dietary sources of natural phenolic antioxidants.     

Characterization of well‐defined poly(ethylene glycol) hydrogels prepared by thiol‐ene chemistry

Considering the large number of applications for hydrogels, a better understanding of the relation between molecular structure and mechanical properties for well‐defined hydrogel is essential. A new library has been compiled of poly(ethylene glycol) polymers (PEG) of different length end functionalized with diallyl, dithiol, and dimethacrylate, and crosslinked with complementary trifunctional crosslinkers. In this study, the hydrogels were initially analyzed by FT‐Raman and NMR to study the conversion ratio of the functional groups. The effects of solvent type, solid content concentration, curing time and length of the PEG chains on the final leaching, swelling and tensile properties of the hydrogels were studied. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Coaxing Solid‐State Phosphorescence from Tellurophenes

The synthesis of the first examples of tellurophenes exhibiting phosphorescence in the solid state and under ambient conditions (room temperature and in air) is reported. Each of these main‐group‐element‐based emitters feature pinacolboronates (BPin) as ring‐appended side groups. The nature of the luminescence observed was also investigated using computational methods.     

Investigation of the solid phase synthesis of tyrosine‐derived diphenol monomers with resin‐bound carbodiimide coupling reagents

Tyrosine‐derived pseudo‐polypeptides have recently been established as potential biomaterials. The bulk production of these polymers is dependant upon the convenient synthesis of tyrosine‐derived diphenolic monomers. Suitable solution phase methods for the synthesis of such monomers, with transient activated esters, have been reported previously by Kohn, J.; Langer, R. In Biomaterials Science: An Introduction to Materials in Medicine; Ratner, B. D.; Hoffman, A. S.; Schoen, F. J.; Lemons, J. E., Eds.; Academic Press: New York, 1996; pp 64–72. However, for all the methods reported by them, purification and isolation of the diphenol monomer involves rigorous extraction, column purification, or an extensive aqueous workup. These may lead to the incorporation of solvent‐based as well as inorganic impurities and also may lead to difficulties in the process scale‐up. In this article, an alternate and relatively more convenient method for the synthesis of tyrosine‐based diphenol monomers is reported. This involved the investigation of polymer resin‐bound carbodiimide in the solid‐phase synthesis of L‐tyrosine‐based diphenolic monomers. This method was found to eliminate the need for rigorous purification processes and was found to maintain reasonable yield as well as maintain purity of the final monomer product. The monomer was able to produce polymers of a reasonably high‐molecular‐weight and a narrow polydispersity. The amide bond formation by such a polymer‐tethered reagent can be described to follow a reverse‐Merrifield sense and the method is relatively convenient to scale up. The L‐tyrosine‐based diphenolic monomeric compound formed by this method was analyzed by NMR, Fourier transform infrared, and elemental microanalysis techniques for chemical structure and composition. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4906–4915, 2004