Advantages of compound‐specific stable isotope measurements over bulk measurements in studies on plant uptake of intact amino acids

Increasing interest in the ability of plants to take up amino acids has given rise to questions on the accuracy of the commonly used bulk method to measure and calculate amino acid uptake. This method uses bulk measurements of ¹³C and ¹⁵N enrichment in plant tissues after application of dual‐labelled amino acids but some authors have recommended the use of compound‐specific stable isotope (CSI) analysis of the plants' amino acids instead. However, there has never been a direct evaluation of both methods. We conducted a field study applying dual‐labelled (¹³C, ¹⁵N) amino acids (glycine, valine, tyrosine and lysine) to soil of a Plantago lanceolata monoculture. Root and shoot samples were collected 24 h after label application and the isotope composition of the plant tissues was investigated using bulk and CSI measurements. Enrichment of ¹³C in the case of CSI measurements was limited to the applied amino acids, showing that no additional ¹³C had been incorporated into the plants' amino acid pool via the uptake of tracer‐derived C‐fragments. Compared with this rather conservative indicator of amino acid uptake, the ¹³C enrichment of bulk measurements was 8, 5, 1.6 and 6 times higher for fine roots, storage roots, shoot and the whole plant, respectively. These findings show that the additional uptake of tracer‐derived C‐fragments will result in a considerable overestimation of amino acid uptake in the case of bulk measurements. We therefore highly recommend the use of CSI measurements for future amino acid uptake studies due to their higher accuracy. Copyright © 2009 John Wiley & Sons, Ltd.     

New protocol for compound‐specific radiocarbon analysis of archaeological bones

Rationale

For radiocarbon results to be accurate, samples must be free of contaminating carbon. Sample pre‐treatment using a high‐performance liquid chromatography (HPLC) approach has been developed at the Oxford Radiocarbon Accelerator Unit (ORAU) as an alternative to conventional methods for dating heavily contaminated bones. This approach isolates hydroxyproline from bone collagen, enabling a purified bone‐specific fraction to then be radiocarbon dated by accelerator mass spectrometry (AMS).

Methods

Using semi‐preparative chromatography and non‐carbon‐based eluents, this technique enables the separation of underivatised amino acids liberated by hydrolysis of extracted bone collagen. A particular focus has been the isolation of hydroxyproline for single‐compound AMS dating since this amino acid is one of the main contributors to the total amount of carbon in mammalian collagen. Our previous approach, involving a carbon‐free aqueous mobile phase, required a two‐step separation using two different chromatographic columns.

Results

This paper reports significant improvements that have been recently made to the method to enable faster semi‐preparative separation of hydroxyproline from bone collagen, making the method more suitable for routine radiocarbon dating of contaminated and/or poorly preserved bone samples by AMS. All steps of the procedure, from the collagen extraction to the correction of the AMS data, are described.

Conclusions

The modifications to the hardware and to the method itself have reduced significantly the time required for the preparation of each sample. This makes it easier for other radiocarbon facilities to implement and use this approach as a routine method for preparing contaminated bone samples.

     

Isolation and desalting with cation‐exchange chromatography for compound‐specific nitrogen isotope analysis of amino acids: application to biogeochemical samples

We have established a procedure for removing interfering materials from extracts of geological and biological samples, in order to determine precise compound‐specific nitrogen isotopic compositions of amino acids. We employed cation‐exchange chromatography of protein and non‐protein amino acids prior to derivatization for gas chromatographic separation. The average recovery of a standard amino acid solution was better than 94%, without nitrogen isotope fractionation during the cation‐exchange chromatography. We applied the procedure to various environmental samples including ‘hard’ (calcareous, siliceous, rock and sediment samples) and ‘soft’ materials (aggregated microbial samples and biological soft tissue samples). We conclude that cation‐exchange chromatography is a pre‐treatment procedure which should be widely useful for the determination of compound‐specific nitrogen isotopic compositions of amino acids. Copyright © 2010 John Wiley & Sons, Ltd.     

Hydropyrolysis over a platinum catalyst as a preparative technique for the compound‐specific carbon isotope ratio measurement of C27 steroids

Compound‐specific stable carbon isotope analysis by gas chromatography/combustion/isotope ratio mass spectrometry (GC/C/IRMS) is an important method for the determination of the ¹³C/¹²C ratios of biomolecules such as steroids, for a wide range of applications. However, steroids in their natural form exhibit poor chromatographic resolution, while derivatisation adds carbon thereby corrupting the stable isotopic composition. Hydropyrolysis with a sulphided molybdenum catalyst has been shown to defunctionalise the steroids, while leaving their carbon skeleton intact, allowing for the accurate measurement of carbon isotope ratios. The presence of double bonds in unsaturated steroids such as cholesterol resulted in significant rearrangement of the products, but replacing the original catalyst system with one of platinum results in higher conversions and far greater selectivity. The improved chromatographic performance of the products should allow GC/C/IRMS to be applied to more structurally complex steroid hormones and their metabolites. Copyright © 2010 John Wiley & Sons, Ltd.     

Use of a temperature‐programmable injector coupled to gas chromatography–combustion–isotope ratio mass spectrometry for compound‐specific carbon isotopic analysis of polycyclic aromatic hydrocarbons

Compound‐specific isotopic analysis (CSIA) can provide information about the origin of analysed compounds; for instance, polycyclic aromatic hydrocarbons (PAHs) in aerosols. This could be a valuable tool in source apportionment of particulate matter (PM) air pollution. Because gas chromatography–combustion–isotope ratio mass spectrometry (GC‐C‐IRMS) analysis requires an amount of at least 10 ng of an individual PAH, a high concentration of PAHs in the injected extract is needed. When the concentration is low a large volume injector creates the possibility of introducing a satisfactory amount of individual PAHs. In this study a temperature‐programmable injector was coupled to GC‐C‐IRMS and injection parameters (solvent level, transfer column flow, transfers time) were optimised using six solid aromatic compounds (anthracene, fluoranthene, pyrene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene) dissolved in n‐pentane and EPA 610 reference mixture. CSIA results for solid PAHs were compared with results obtained for the single components analysed by elemental analysis–isotope ratio mass spectrometry. The injection method was validated for two sample injection volumes, 50 and 100 µL. This method was also compared with commonly used splitless injection. To be included in the study, measurements had to have an uncertainty lower than 0.5‰ for and a minimum peak height of 200 mV. The lower concentration limits at which these criteria were fulfilled for PAHs were 30 mg/L for 1 µL in splitless injection and 0.3 and 0.2 mg/L for 50 and 100 µL, respectively, in large volume injection. Copyright © 2009 John Wiley & Sons, Ltd.