Facile synthesis of amphiphilic gels by frontal free‐radical polymerization

We report a new facile strategy for quickly synthesizing poly(2‐hydroxyethyl acrylate‐co‐vinyl versatate) amphiphilic gels with excellent physicochemical properties by frontal free‐radical polymerization. The appropriate amounts of 2‐hydroxyethyl acrylate, vinyl versatate (VeoVa 9) and ammonium persulfate initiator were mixed together at ambient temperature in the presence of N‐methyl‐2‐pyrrolidone as the solvent medium. Frontal polymerization (FP) was initiated by heating the wall of the tube with a soldering iron. Once initiated, no further energy was required for the polymerization to occur. The dependence of the front velocity and front temperature on the initiator concentration was investigated. The front temperatures were between 132 and 157 °C, depending on the initiator concentration. The morphology, swelling rate, and swelling behavior of amphiphilic gels prepared via FP were comparatively investigated on the basis of scanning electron microscopy, water contact angle, and swelling measurements. Results show that the amphiphilic gels prepared via FP behave with good swelling capacity both in water and organic solvents. The FP can be exploited as an alternative means for synthesis of amphiphilic gels with additional advantages of fast and efficient way. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 823–831, 2010     

Facile synthesis of poly(DMC‐co‐HPA) hydrogels via infrared laser ignited frontal polymerization and their adsorption–desorption switching performance

In this work, we report a versatile infrared laser ignited frontal polymerization technique for the fabrication of a series of poly(DMC‐co‐HPA) hydrogels (DMC = methacryloxyethyltrimethyl ammonium chloride, HPA = hydroxypropyl acrylate). Because the method is based on the exothermic reaction, no further energy is required in the reaction once it is initiated. Moreover, we have found the polymerization process is a pure frontal polymerization model without involving any other reaction process. The dependence of frontal velocity and temperature on the reaction time is thoroughly discussed. The as‐prepared hydrogels are pH‐responsive and their maximum equilibrium swelling ratio could reach ～3,890%. Also, the as‐prepared poly(DMC‐co‐HPA) hydrogels capable of adsorption/desorption switching performance can be utilized for heavy metal ion removal in wastewater treatments. Interestingly, the hydrogels can float on the water surface after intaking heavy metal ions by the combination of kerosene and polyoxyethylene sorbitan monolaurate (Tween 20) in hydrogel components, greatly enhancing treatment efficiency. We believe the method described herein to rapidly construct functional hydrogels with the ability to remove heavy metal ions may find unique applications in emergency processing of water pollution. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2085–2093     

A facile pathway for the fast synthesis of colloidal crystal‐loaded hydrogels via frontal polymerization

In this work, a dually sensitive colloidal crystal (CC)‐loaded hydrogel has been synthesized via frontal polymerization (FP) in a facile and rapid way. First, a polystyrene CC film was fabricated by vertical deposition on the inner wall of a test tube. Then, a mixture of acrylic acid (AAc), 2‐hydroxyethyl methacrylate (HEMA), and glycerol along with the initiator and crosslinker was added to this test tube to carry out FP, resulting in the formation of CC‐loaded hydrogel. The influence of the mass ratios of HEMA/AAc on front velocity and temperatures were studied. The swelling behavior, the morphology, and the stimuli‐responsive behavior of the CC‐loaded hydrogels prepared via FP were thoroughly investigated on the basis of swelling measurement, scanning electron microscopy, and reflection spectra. Results show that the as‐prepared CC‐loaded hydrogels exhibit excellent dual sensitivity to both methanol concentrations and pH values with very short response time, which can be observed visually without the aid of instruments. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Polymer hydrogels of 2‐hydroxyethyl acrylate and acrylic acid obtained by frontal polymerization

In this work, we report on the synthesis and characterization of homopolymers and copolymers of acrylic acid and 2‐hydroxyethyl acrylate prepared by the use of the frontal polymerization (FP) technique. Tetraethyleneglycoldiacrylate was used as a crosslinker and benzoyl peroxide as an initiator. The maximum temperatures reached by the front were in the range between 214 °C and 296 °C. Besides, front velocities ranged between 3.9 and 10.8 cm/min, the latter being one of the highest values reported so far in the FP literature. Differential scanning calorimetry was used to estimate the conversion degree, which was always comprised between 90% and 96%, and to determine the glass transition temperatures, which were found to be dependent on the composition, with values ranging from 13 °C to 168 °C. Moreover, the obtained materials were allowed to swell in aqueous solutions at various pH. The samples exhibit a moderate increase of the swelling ratio percentage (SR%) at pH ≈ 5–6, and a sudden and larger SR% increase at pH ≈ 12–13 depending on the composition, thus indicating the obtainment of pH‐responsive polymer hydrogels. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Facile synthesis of poly(hydroxyethyl acrylate) by frontal free‐radical polymerization

We report the first synthesis of poly(hydroxyethyl acrylate) (PHEA) without solvent by free‐radical frontal polymerization (FP) at ambient pressure. In a typical run, the appropriate amounts of reactant (hydroxyethyl acrylate) and initiator (1,1‐di(tert‐butylperoxy)‐3,3,5‐trimethylcyclohexane) (Luperox 231) were mixed together at ambient pressure. FP was initiated by heating the wall of the tube with a soldering iron, and the resultant hot fronts were allowed to self‐propagate throughout the reaction vessel. Once initiated, no further energy was required for polymerization to occur. To study the macrokinetics, we also produced PHEA frontally with ammonium persulfate as initiator and dimethyl sulfoxide as the solvent. The dependences of the front velocity and front temperature on the initiator concentration and reactant dilution were investigated. The front temperatures were between 124 and 157 °C, depending on the ammonium persulfate concentration. Thermogravimetric analysis indicates that PHEA prepared by FP with ammonium persulfate as initiator had higher thermal stability than solvent‐free frontally prepared PHEA with Luperox 231 as initiator. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 873–881, 2007     

Facile and quick synthesis of poly(N‐methylolacrylamide)/polyhedral oligomeric silsesquioxane graft copolymer hybrids via frontal polymerization

We report on a new strategy for fabricating well‐defined POSS‐based polymeric materials with and without solvent by frontal polymerization (FP) at ambient pressure. First, we functionalize polyhedral oligomeric silsesquioxane (POSS) with isophorone diisocyanate (IPDI). With these functionalized POSS‐containing isocyanate groups, POSS can be easily incorporated into a poly(N‐methylolacrylamide) (PNMA) matrix via FP in situ. Constant velocity FP is observed without significant bulk polymerization. The morphology and thermal properties of POSS‐based hybrid polymers prepared via FP are comparatively investigated on the basis of scanning electronic microscopy (SEM) and thermogravimetric analysis (TGA). Results show that the as‐prepared POSS‐based polymeric materials exhibit a higher glass transition temperature than that of pure PNMA, ascribing to modified POSS well‐dispersed in these hybrid polymers. Also, the products with different microstructures display different thermal properties. The pure PNMA exhibits a featureless morphology, whereas a hierarchical morphology is obtained for the POSS‐based polymeric materials. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1136–1147, 2009     

Synthesis and characterization of graphene‐containing thermoresponsive nanocomposite hydrogels of poly(N‐vinylcaprolactam) prepared by frontal polymerization

Thermoresponsive poly(N‐vinylcaprolactam) nanocomposite hydrogels containing graphene were successfully prepared by frontal polymerization. High concentration of graphene (5.0 mg/mL) was obtained by direct graphite sonication in the self‐same liquid monomer, thus avoiding any chemical manipulation and obtaining “real” graphene as nanofiller instead of one of its more or less oxidized derivative, which is what generally reported in published reports. Furthermore, the corresponding nanocomposites were obtained without using any solvent to be eventually removed. The materials were fully characterized by RAMAN, SEM, and TEM, and their swelling behavior and rheological properties were investigated. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

First solvent‐free synthesis of poly(N‐methylolacrylamide) via frontal free‐radical polymerization

We report the first synthesis of poly (N‐methylolacrylamide) (PNMA) via free‐radical frontal polymerization (FP) with solid monomers at ambient pressure. The appropriate amounts of reactants (N‐methylolacrylamide) (NMA) and initiator (ammonium persulfate) were mixed together at ambient temperature without solvent. FP was initiated by heating the wall of the tube with a soldering iron, and the resultant hot fronts were allowed to self‐propagate throughout the reaction vessel. Once initiated, no further energy was required for polymerization to occur. To suppress the fingers of molten monomer, a small amount of nanosilica was added. We also produced PNMA with dimethyl sulfoxide (DMSO) or N‐methyl‐2‐pyrrolidone, as solvent by FP, to study the macrokinetics in FP of PNMA without fillers. The front velocity and front temperature dependence on the ammonium persulfate and N‐methyl‐2‐pyrrolidone concentration were investigated. The polymer was analyzed by thermogravimetric analysis. Results show that without postpolymerization solvent removal, waste production can be reduced. Solvent‐free FP could be exploited as a means for preparation of PNMA with the potential advantage of higher throughput than solvent‐based methods. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4322–4330, 2007     

Facile synthesis of fluorescent quantum dot‐polymer nanocomposites via frontal polymerization

We report an available approach for quickly fabricating CdS QD‐polymer nanocomposites via frontal polymerization (FP). First, we synthesized (3‐mercaptopropyl)‐1‐trimethoxysilane (MPS)‐capped CdS quantum dots (QDs). With these MPS‐capped CdS QDs containing mercapto groups, MPS‐capped CdS QDs can be easily incorporated into a poly(N‐methylolacrylamide) (PNMA) matrix via FP. A variety of features for preparing QD‐polymer nanocomposites, such as initiator concentration and CdS concentration, were thoroughly investigated. The fluorescence properties of QD‐polymer nanocomposites prepared via FP are comparatively investigated on the basis of ultraviolet–visible (UV–vis) spectra and photoluminescence (PL) spectra. Results show that the PL intensity of QD‐polymer nanocomposites prepared via the FP method is superior to that obtained by the traditional batch polymerization (BP) method. In addition, by measuring the changes of PL intensity of the samples immersed in different concentrations of copper acetate solution, we found the QD‐polymer nanocomposites can be ultrasensitive to copper ions. This FP process can be exploited as a facile and rapid way for synthesis QD‐polymer nanocomposites on a large scale, avoiding the fluorescence quenching of nanocrystals during incorporation nanocrystals into polymer matrices. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2170–2177, 2010     

Synthesis of transition‐metal‐ion‐selective poly(N‐isopropylacrylamide) hydrogels by the incorporation of an Aza crown ether

A functionalized cyclam was synthesized by the attachment of a polymerizable acryloyl group to one of the four nitrogens on the cyclam molecule. The polymerization of the functionalized cyclam was performed with N‐isopropylacrylamide and N,N′‐methylene bisacrylamide, and the gels obtained were studied in the presence of different transition‐metal‐ion solutions. There was a drastic difference in the phase‐transition temperature (T_c) of the poly(N‐isopropylacrylamide) (PNIPAAm)/cyclam gel in comparison with the pure PNIPAAm gel. For the described system, a T_c shift of 15 °C was obtained. The presence of functionalized cyclam increased the hydrophilicity and T_c of the aforementioned polymer gels in deionized water (at pH 6) because of the presence of protonated amino moieties. The PNIPAAm/cyclam gels showed a dependence of the swelling behavior on pH. T_c of the pure PNIPAAm gel was weakly influenced by the presence of any transition‐metal ions, such as Cu²⁺, Ni²⁺, Zn²⁺, and Mn²⁺. The addition of Cu²⁺ or Ni²⁺ to the PNIPAAm/cyclam gel reduced T_c of the polymer gel, and a shift of approximately 12 °C was observed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1594–1602, 2003     

Synthesis of low‐polydispersity poly(N‐ethylmethylacrylamide) by controlled radical polymerizations and their thermal phase transition behavior

Controlled radical polymerizations of N‐ethylmethylacrylamide (EMA) by atom transfer radical polymerization and reversible addition‐fragmentation chain transfer processes were investigated in detail for the first time, employing complementary characterization techniques including gel permeation chromatography, ¹H NMR spectroscopy, and matrix‐assisted laser desorption ionization time‐of‐flight mass spectrometry. In both cases, relatively good control of the polymerization of EMA was achieved, as revealed by the linear evolution of molecular weights with monomer conversions and the low polydispersity of poly(N‐ethylmethylacrylamide) (PEMA). The thermal phase transitions of well‐defined PEMA homopolymers with polydispersities less than 1.2 and degrees of polymerization up to 320 in aqueous solution were determined by temperature‐dependent turbidity measurements. The obtained cloud points (CPs) vary in the range of 58–68 °C, exhibiting inverse molecular weight and polymer concentration dependences. Moreover, the presence of a carboxyl group instead of an alkyl one at the PEMA chain end can elevate its CP by ～3–4 °C. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 60–69, 2008     

Heterotactic‐specific radical polymerization of N‐isopropylacrylamide and phase transition behavior of aqueous solution of heterotactic poly(N‐isopropylacrylamide)

Radical polymerization of N‐isopropylacrylamide (NIPAAm) in toluene at low temperatures, in the presence of fluorinated‐alcohols, produced heterotactic polymer comprising an alternating sequence of meso and racemo dyads. The heterotacticity reached 70% in triads when polymerization was carried out at ?40 °C using nonafluoro‐tert‐butanol as the added alcohol. NMR analysis revealed that formation of a 1:1 complex of NIPAAm and fluorinated‐alcohol through C?O···H? O hydrogen bonding induces the heterotactic specificity. A mechanism for the heterotactic‐specific polymerization is proposed. Examination of the phase transition behavior of aqueous solutions of heterotactic poly(NIPAAm) revealed that the hysteresis of the phase transition between the heating and cooling cycles depended on the average length of meso dyads in poly(NIPAAm). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2539–2550, 2009     

Interpretation of the polyelectrolyte and antipolyelectrolyte effects of poly(N‐vinylimidazole‐co‐sodium styrenesulfonate) hydrogels

Hydrogels of N‐vinylimidazole (VI) and sodium styrenesulfonate (SSS) were synthesized in aqueous solution by radical crosslinking copolymerization with N,N′‐methylene‐bis(acrylamide) as crosslinker. Swelling in several saline solutions was measured for hydrogel samples synthesized with different comonomer concentrations (C_T = 10, 25, or 40%) and with SSS mole fractions covering a broad range (f_SSS = 0–0.7), while the crosslinker ratio was 2 wt % in all cases. The degree of swelling in aqueous solution with a specific ionic strength (μ), plotted versus the SSS composition of the feed, shows a minimum for any set of samples synthesized with a fixed C_T. The dependence of swelling on μ shows both polyelectrolyte (f_SSS beyond the minimum) and antipolyelectrolyte behaviors (in the low f_SSS limit). It was found that the nonGaussian factor of the crosslinking density and the polymer‐solvent interaction parameter increase with f_SSS for any C_T. Moreover, in the low f_SSS limit, the osmotic swelling pressure is governed not only by the ionic contribution, but also by the polymer‐solvent mixing and, the concentration of mobile counterions inside the gel is not proportional to the net fixed charge but to the addition of cationic and anionic side groups, what discards the formation of ionic pairs. The antipolyelectrolyte effect is interpreted as due to the increasing protonation of VI as μ goes up. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1683–1693, 2007     

Facile synthesis of self‐healing gel via magnetocaloric bottom‐ignited frontal polymerization

A series of the self‐healing gels facilely fabricated by VI (N‐vinyl imidazole) and MAH‐β‐CD (β‐cyclodextrin grafted vinyl carboxylic acid groups) via bottom‐ignited frontal polymerization (BIFP) initiated by magnetocaloric effect. Once ignited the bottom phase, the heat upward propagates to generate the “front” in the upper phase. Then, no further energy is added to maintain the reaction and the whole polymerization process experiences within minutes. In this system, the dependence of frontal velocity and temperature, along with morphology, swelling capacity, mechanical property, and self‐healing efficiency, on the preparation parameters is investigated. Interestingly, the gels show good swelling capacity in the organic solvent, comparatively almost no absorption in water. Moreover, the as‐prepared gels exhibit excellent auto‐healing properties without any external stimuli at ambient temperature. The healed sample possesses 97% recovery of its tensile strength after 8 h healing time, which relies largely on the host–guest interaction between VI and MAH‐β‐CD. The results demonstrate that FP can be utilized as an efficient and energy‐saving method to synthesize self‐healing supramolecular gels. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2585–2593     

Rapid synthesis of poly(HPA‐co‐VeoVa 10) amphiphilic gels toward removal of toxic solvents via plasma‐ignited frontal polymerization

Atmospheric air plasma was created and applied in the frontal polymerization (FP) of fabricating poly(HPA‐co‐VeoVa 10) amphiphilic gels (HPA = 2‐hydroxypropyl acrylate, VeoVa 10 = vinyl versatate) with enhanced physicochemical properties. In plasma‐ignited frontal polymerization (PIFP), once ignited by air plasma, no further energy or treatment was required for the following polymerization. In this system, the comparison between PIFP and thermal frontal polymerization (TFP) was conducted and observed that PIFP and TFP differ considerably in terms of swelling capacity, morphology and component distribution of the products. This finding is of great importance that the simultaneous generation of active radicals in the initial stage can spread throughout reactant and anchor on the synthetic polymer with the assistance of FP. More interestingly, the PIFP‐synthesized copolymer possesses remarkable selective absorption towards organic solvents, which can be facilely manipulated by varying the weight ratios of HPA/VeoVa 10. Obviously, these polymer products could serve as an “organic solvent scavenger” in the field of industrial wastewater treatment. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of well‐defined 7‐arm and 21‐arm poly(N‐isopropylacrylamide) star polymers with β‐cyclodextrin cores via click chemistry and their thermal phase transition behavior in aqueous solution

The syntheses of well‐defined 7‐arm and 21‐arm poly(N‐isopropylacrylamide) (PNIPAM) star polymers possessing β‐cyclodextrin (β‐CD) cores were achieved via the combination of atom transfer radical polymerization (ATRP) and click reactions. Heptakis(6‐deoxy‐6‐azido)‐β‐cyclodextrin and heptakis[2,3,6‐tri‐O‐(2‐azidopropionyl)]‐β‐cyclodextrin, β‐CD‐(N₃)₇ and β‐CD‐(N₃)₂₁, precursors were prepared and thoroughly characterized by nuclear magnetic resonance and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry. A series of alkynyl terminally functionalized PNIPAM (alkyne‐PNIPAM) linear precursors with varying degrees of polymerization (DP) were synthesized via atom transfer radical polymerization (ATRP) of N‐isopropylacrylamide using propargyl 2‐chloropropionate as the initiator. The subsequent click reactions of alkyne‐PNIPAM with β‐CD‐(N₃)₇ and β‐CD‐(N₃)₂₁ led to the facile preparation of well‐defined 7‐arm and 21‐arm star polymers, namely β‐CD‐(PNIPAM)₇ and β‐CD‐(PNIPAM)₂₁. The thermal phase transition behavior of 7‐arm and 21‐arm star polymers with varying molecular weights were examined by temperature‐dependent turbidity and micro‐differential scanning calorimetry, and the results were compared to those of linear PNIPAM precursors. The anchoring of PNIPAM chain terminal to β‐CD cores and high local chain density for star polymers contributed to their considerably lower critical phase separation temperatures (T_c) and enthalpy changes during phase transition as compared with that of linear precursors. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 404–419, 2009     

Thermoresponsive super water absorbent hydrogels prepared by frontal polymerization of N‐isopropyl acrylamide and 3‐sulfopropyl acrylate potassium salt

Super water absorbent polymer hydrogels were synthesized by frontal polymerization. These materials were obtained by copolymerizing N‐isopropyl acrylamide (NIPAAm) and 3‐sulfopropyl acrylate potassium salt (SPAK) in the presence of N,N′‐methylene‐bis‐acrylamide as a crosslinker. It was found that their swelling behavior in water can be easily tuned by using either the appropriate monomer ratio or the amount of the crosslinker used. Namely, the swelling ratio was found to range from about 1000% for the NIPAAm homopolymer in the presence of 5.0 mol % of crosslinker, up to 35,000% for the sample containing 87.5 mol % of SPAK and 1.0 mol % of crosslinker. The affinity toward water was also confirmed by contact angle analysis. Moreover, the obtained hydrogels exhibit a thermoresponsive behavior, with a lower critical solution temperature of about 28–30 °C. This value is close to that of poly(NIPAAm) but with a swelling capability that dramatically increases as the amount of SPAK increases. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of thermo‐responsive poly(N‐vinylcaprolactam)‐containing block copolymers by cobalt‐mediated radical polymerization

Thermo‐responsive block copolymers based on poly(N‐vinylcaprolactam) (PNVCL) have been prepared by cobalt‐mediated radical polymerization (CMRP) for the first time. The homopolymerization of NVCL was controlled by bis(acetylacetonato)cobalt(II) and a molecular weight as high as 46,000 g/mol could be reached with a low polydispersity. The polymerization of NVCL was also initiated from a poly(vinyl acetate)‐Co(acac)₂ (PVAc‐Co(acac)₂) macroinitiator to yield well‐defined PVAc‐b‐PNVCL block copolymers with a low polydispersity (M_w/M_n = 1.1) up to high molecular weights (M_n = 87,000 g/mol), which constitutes a significant improvement over other techniques. The amphiphilic PVAc‐b‐PNVCL copolymers were hydrolyzed into unprecedented double hydrophilic poly(vinyl alcohol)‐b‐PNVCL (PVOH‐b‐PNVCL) copolymers and their temperature‐dependent solution behavior was studied by turbidimetry and dynamic light scattering. Finally, the so‐called cobalt‐mediated radical coupling (CMRC) reaction was implemented to PVAc‐b‐PNVCL‐Co(acac)₂ precursors to yield novel PVAc‐b‐PNVCL‐b‐PVAc symmetrical triblock copolymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

PEGDA‐based luminescent polymers prepared by frontal polymerization

Frontal polymerization (FP) of poly(ethylene glycol) diacrylate (PEGDA) was carried out using benzoyl peroxide (BPO) as radical initiator. In addition, a pyrene containing monomer, 1‐pyrenebutyl acrylate (PyBuAc), was incorporated as a fluorescent probe in order to obtain luminescent materials with different chromophore contents. The resulting polymers were characterized by FT‐IR spectroscopy in the solid state and their thermal properties were determined by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Moreover, the optical properties of these materials were studied by absorption and fluorescence spectroscopy. The maximum amount of the incorporated pyrene‐containing monomer into the polymer matrix was limited to 1 wt % by the polymerization process. The obtained labeled polymers poly(PEGDA‐co‐PyBuAc) exhibited a broad absorption band at 345 nm. The fluorescence spectra of these polymers exhibited mainly “monomer emission” so that no excimer emission was observed. It is possible to tune the color of the emitted light by varying the pyrene content in the samples. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2890–2897