Conjugation of bioactive groups to poly(lactic acid) and poly[(lactic acid)-co-(glycolic acid)] films

A novel PLA-based polymer containing reactive pendent ketone or hydroxyl groups was synthesized by the copolymerization of L-lactide with epsilon-caprolactone-based monomers. The polymer was activated with NPC, resulting in an amine-reactive polymer which was then cast into thin polymeric films, either alone or as part of a blend with PLGA, before immersion into a solution of the cell adhesion peptide GRGDS in PBS buffer allowed for conjugation of GRGDS to the film surfaces. Subsequent 3T3 fibroblast cell adhesion studies demonstrated an increase in cellular adhesion and spreading over films cast from unmodified PLGA. Hence the new polymer can be used to obtain covalent linkage of amine-containing molecules to polymer surfaces.     

Comparison of the growth and degradation of poly(glycolic acid) and poly(ε‐caprolactone) brushes

The growth and degradation of poly(glycolic acid) (PGA) and poly(ε‐caprolactone) (PCL) brushes were compared. Using tin (octanoate) as the catalyst, optimal conditions were found for growth of each polyester brush from the hydroxy‐terminated silicon surface via ring‐opening polymerization. PCL brushes grew thicker at elevated temperatures but the thickest PGA brushes grew at room temperature. Unlike bulk polyesters that can degrade under both acidic and basic conditions, the confined surface polyester brushes only degraded under neutral or basic conditions. The degradation mechanism of grafted polyester brushes was probed through a blocking test. It was shown that the terminal hydroxy groups of these polyester brushes were essential to the degradation process indicating a preferential backbiting mechanism. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4643–4649     

Poly(allyl glycidyl ether)-A versatile and functional polyether platform

Allyl glycidyl ether, polymerized from potassium alkoxide/naphthalenide initiators under both neat and solution conditions was shown to be a highly-controlled process. In both cases, molar masses (10-100 kg/mol) were determined by the reaction stoichiometry, and low polydispersity indices (1.05-1.33) could be obtained with a full understanding of the dominant side reaction, isomerization of the allyl side chain, being developed. The degree of isomerization of allyl to cis-prop-1-enyl ether groups (0 - 10 % mol.) was not correlated to the molar mass or polydispersity of the polymer but was dictated by the polymerization temperature. This allows the extent of isomerization to be reduced to essentially zero under either melt or solution conditions at polymerization temperatures of less than 40 °C.     

Poly(thioester)s

Syntheses and properties of aliphatic and aromatic polythioesters (PTEs) were reviewed including polythiocarbonates and polythiourethanes. The content is subdivided into the following sections: PTEs of aliphatic α‐mercapto carboxylic acid, PTEs of ω‐mercapto carboxylic acids, PTEs derived from α,ω‐dimercapto alkanes, aromatic poly(thioester)s, aliphatic poly(thiocarbonate)s, aliphatic poly(thiourethane)s and aromatic polythiocarbonates. The synthetic strategies reviewed in this article include anionic and cationic ring‐opening polymerizations, polycondensations in bulk, polycondensations in solutions, interfacial polycondensations and in vitro enzymatic polycondensations.     

Photochemically Cross‐linked Poly(aryl ether ketone) Rings

Summary: Macrocyclic phenyl ether ketones were prepared via pseudo high dilution condensation. Irradiation of these rings with UV light in a solution containing isopropyl alcohol as hydrogen donor resulted in a photo‐induced reduction of benzophenone to benzopinacol and the formation linked macrocycles. These rings can be heated to undergo ring‐opening polymerization and produce a polymer network or they can be added to a polycondensation reaction to prepare poly(ether ether ketones) with variable degrees of cross‐linking.

Photochemical cross‐linking of PEK rings and ring opening polymerization (n: 2–6). (a) hν, iPrOH, DCM; (b) CsF, 260 °C (polymer 3 ); (c) 4,4′–difluorobenzophenone, hydroquinone, diphenylsulphone, K₂CO₃, 260 °C (2% polymer 4 ; 6% polymer 5 ).     

Poly(lactic acid) composites with poly(lactic acid)‐modified carbon nanotubes

This work reports the study of the effect of chemical functionalization of carbon nanotubes on their dispersion in poly(lactic acid). The nanotubes were functionalized by the 1,3‐dipolar cycloaddition reaction, generating pyrrolidine groups at the nanotube surface. Further reaction of the pyrrolidine groups with poly(lactic acid) was studied in solution and in the polymer melt. The former involved refluxing the nanotubes in a dimethylformamide/polymer solution; the latter was carried out by direct melt mixing in a microcompounder. The carbon nanotubes collected after each process were characterized by thermogravimetry and by X‐ray photoelectron spectroscopy, showing evidence of polymer bonded to the nanotube surface only when the reaction was carried out in the polymer melt. The composites with polymer modified nanotubes present smaller average agglomerate area and a narrower agglomerate area distribution. In addition, they show improved tensile properties at low CNT concentration and present lower electrical resistivity. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3740–3750     

Synthesis and characterization of amphiphilic block copolymer of polyphosphoester and poly(L‐lactic acid)

Aliphatic polyesters and polyphosphoesters (PPEs) have received much interest in medical applications due to their favorable biocompatibility and biodegradability. In this work, novel amphiphilic triblock copolymers of PPE and poly(L ‐lactic acid) (PLLA) with various compositions were synthesized and characterized. The blocky structure was confirmed by GPC analyses. These triblock copolymers formed micelles composed of hydrophobic PLLA core and hydrophilic PPE shell in aqueous solution. Critical micellization concentrations of these triblock copolymers were related to the polymer compositions. Incubation of micelles at neutral pH followed by GPC analyses revealed that these polymer micelles were hydrolysized and resulted in decreased molecular weights and small oligomers, whereas its degradation in basic and acid mediums was accelerated. MTT assay also demonstrated the biocompatibility against HEK293 cells. These biodegradable polymers are potential as drug carriers for biomedical application. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6425–6434, 2008     

N‐heterocyclic carbenes as organocatalysts in controlled/living ring‐opening polymerization of O‐carboxyanhydrides derived from l‐lactic acid and l‐mandelic acid

An organocatalytic approach to controlled/living ring‐opening polymerizations (ROPs) of O‐carboxyanhydrides (OCAs) using N‐heterocyclic carbenes (NHCs) as nucleophilic catalysts has been investigated. NHCs with different structures were used in order to compare the catalytic performances in the ROP of OCA of l ‐lactic acid. ¹H NMR, SEC, and MALDI‐TOF MS measurements of the products clearly indicated a controlled/living manner of the polymerization. The controlled/living nature was further confirmed by kinetic and chain extension experiments. Additionally, polylol initiators were used to produce α,ω‐dihydroxy telechelic, 3‐, and 4‐armed star‐shaped polymers. Moreover, star‐shaped diblock copolymer, bearing methyl and phenyl side groups, has been successfully synthesized with OCA/NHC system. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 . 52, 2306–2315     

Hierarchical Self‐Assembly of Double‐Crystalline Poly(ferrocenyldimethylsilane)‐block‐poly(2‐iso‐propyl‐2‐oxazoline) (PFDMS‐b‐PiPrOx) Block Copolymers

The step‐wise solution self‐assembly of double crystalline organometallic poly(ferrocenyldimethylsilane)‐block‐poly(2‐iso‐propyl‐2‐oxazoline) (PFDMS‐b‐PiPrOx) diblock copolymers is demonstrated. Two block copolymers are obtained by copper‐catalyzed azide‐alkyne cycloaddition (CuAAC), featuring PFDMS/PiPrOx weight fractions of 46/54 (PFDMS₃₀‐b‐PiPrOx₇₅) and 30/70 (PFDMS₃₀‐b‐PiPrOx₁₅₅). Nonsolvent induced crystallization of PFDMS in acetone leads in both cases to cylindrical micelles with a PFDMS core. Afterward, the structures are transferred into water for sequential temperature‐induced crystallization of the PiPrOx corona, leading to hierarchical double crystalline superstructures, which are investigated using scanning electron microscopy, wide angle X‐ray scattering, and differential scanning calorimetry.

     

A Functionalized Cyclic Lactide Monomer for Synthesis of Water‐Soluble Poly(Lactic Acid) and Amphiphilic Diblock Poly(Lactic Acid)

Biodegradable and bioabsorbable poly(lactic acid)s are one of the most important biomedical materials. However, it is difficult to introduce the functional groups into poly(lactic acid)s in order to improve their hydrophilicity and degradation rate. Here the authors describe the synthesis of functionalized cyclic lactide monomer 3,6‐bis(benzyloxymethyl)‐1,4‐dioxane‐2,5‐dione (BnLA) using an advanced synthetic route. Water‐soluble hydroxyl‐functionalized homopoly(lactic acid) (P(OH)LA) is synthesized via ring‐opening polymerization (ROP) of BnLA, followed by a hydrogenolytic deprotection reaction. Amphiphilic diblock poly(lactic acid) (P(OH)LA‐PLA) is synthesized via ROP of DL‐lactide using PBnLA as an initiator, followed by a hydrogenolytic deprotection reaction. P(OH)LA‐PLA is able to form polymeric micelles with the diameter of sub‐100 nm.

     

Poly(p‐phenylene methylene)‐based block copolymers by mechanistic transformation

The synthesis of poly(p‐phenylene methylene) (PPM)‐based block copolymers such as poly(p‐phenylene methylene)‐b‐poly(ε‐caprolactone) and poly(p‐phenylene methylene)‐b‐polytetrahydrofuran by mechanistic transformation was described. First, precursor PPM was synthesized by acid‐catalyzed polymerization of tribenzylborate at 16 °C. Then, this polymer was used as macroinitiators in either ring‐opening polymerization of ε‐caprolactone or cationic ring‐opening polymerization of tetrahydrofuran to yield respective block copolymers. The structures of the prepolymer and block copolymers were characterized by GPC and ¹H NMR investigations. The composition of block copolymers as determined by ¹H NMR and TGA analysis was found to be in very good agreement. The thermal behavior and surface morphology of the copolymers were also investigated, respectively, by differential scanning calorimetry and atomic force microscopy measurements, and the contribution of the major soft segment has been observed. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Functional Polyolefins: Poly(ethylene)‐graft‐Poly(tert‐butyl acrylate) via Atom Transfer Radical Polymerization From a Polybrominated Alkane

Poly(cis‐cyclooctene) is synthesized via ring‐opening metathesis polymerization in the presence of a chain‐transfer agent and quantitatively hydrobrominated. Subsequent graft polymerization of tert‐butyl acrylate (tBA) via Cu‐catalyzed atom transfer radical polymerization (ATRP) from the non‐activated secondary alkyl bromide moieties finally results in PE‐g‐PtBA copolymer brushes. By varying the reaction conditions, a series of well‐defined graft copolymers with different graft densities and graft lengths are prepared. The maximum extent of grafting in terms of bromoalkyl groups involved is approximately 80 mol%. DSC measurements on the obtained graft copolymers reveal a decrease in T_m with increasing grafting density.     

Synthesis of Poly(lactide)s with Modified Thermal and Mechanical Properties

The use of poly(lactide)‐based materials is, in part, limited by their physical and mechanical properties. This article reviews the methods that have been employed to enable enhancement of the materials properties through synthetic manipulation of the polymer structure including block copolymer synthesis and modification of the lactide monomer structure, focusing on the application of ring‐opening polymerization. In turn the effect of these structural modifications on the properties of the resultant materials are reported.

     

Ring‐opening polymerization of the cyclic dimer of poly(trimethylene terephthalate)

Poly(trimethylene terephthalate) (PTT) was prepared by the ring‐opening polymerization of its cyclic dimer. Antimony(III) oxide, titanium(IV) butoxide, dibutyltin oxide, and titanium(IV) isopropoxide were used as catalysts. Among the catalysts, titanium(IV) butoxide was the most effective for the same reaction conditions. A weight‐average molecular weight of 63,500 g/mol was obtained from ring‐opening poly merization at 265 °C for 2 h in the presence of 0.5 mol % titanium(IV) butoxide. The PTTs obtained from the polymerization catalyzed with increasing amounts of antimony(III) oxide showed increasing weight‐average molecular weights and reaction conversions. When 1 mol % antimony(III) oxide was used, the weight‐average molecular weight was 32,000 g/mol and the conversion was 82% after 1 h of polymerization at 265 °C. In the case of the polymer catalyzed by titanium(IV) butoxide under the same conditions, the weight‐average molecular weight and conversion were 40,000 g/mol and 77% when 0.25 mol % was used, whereas 0.5 mol % catalyst produced a weight‐average molecular weight of 27,000 g/mol and a conversion of 95%. To get an acceptable molecular weight and relatively high reaction conversion, a catalyst concentration of at least 0.5 mol % was found to be necessary, in contrast to conventional condensation polymerizations, which require only about one‐tenth of this amount of the catalyst. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6801–6809, 2006     

Synthesis and ring‐opening polymerization of macrocyclic (arylene thioether ketone) oligomers

Macrocyclic (arylene thioether ketone) oligomers together with a linear poly(phenylene sulfide ketone) oligomer were synthesized by a one‐step reaction. The macrocycles and linear oligomer were fully characterized by ¹³C‐NMR, H‐NMR, matrix assisted laser desorption/ionization time‐of‐flight mass spectrometry (MALDI‐TOF‐MS), differential scanning calorimetry (DSC) and FT‐IR. Uncatalyzed, simultaneously ring‐opening polymerization (ROP) of the macrocycles and the mixture of macrocycles and linear oligomer were carried out under dynamic heating conditions. The ROP temperature of the macrocycles decreased upon mixing it with the linear oligomer. The ROP conditions and mechanism were investigated and discussed. The macrocycles and their mixture show potential applications in high temperature adhesives and sealants. Copyright © 2006 John Wiley & Sons, Ltd.     

Poly(lactic acid) Polymerized by Aluminum Triflate

The ring-opening polymerization of L -lactide (LA) has been initiated by aluminum triflate (trifluoromethanesulfonate) in air using a simple glass tube at 100 °C without desiccation steps and stirring. It was found that the molecular weight of poly(lactic acid) (PLA) was increased by the addition of an alcohol as an initiator to the reaction mixture. The highest number averaged molecular weight, molecular weight distribution, and recovery of the obtained PLA at 100 °C for 6 h were 18,200, 1.20, and 73%, respectively. With the addition of a small percentage of alcohol and a long reaction time of the polymerization method with the re-addition of LA, PLA (ca. 80 wt%) with a higher molecular weight (ca. 30,000) initiated by the added alcohol was produced with PLA (ca. 20 wt%) with a lower molecular weight (ca. 2,000) initiated by impurities such as water, which exist in a monomer, initiator, or catalyst.     

Well‐defined poly(oxazoline)‐b‐poly(acrylate) amphiphilic copolymers: From synthesis by polymer–polymer coupling to self‐organization in water

In this contribution, we report on the self‐assembly in water of original amphiphilic poly(2‐methyl‐2‐oxazoline)‐b‐poly(tert‐butyl acrylate) copolymers, synthesized by copper‐catalyzed azide–alkyne cycloaddition (CuAAC) reaction. For such purpose, (poly(2‐methyl‐2‐oxazoline)) and (poly(tert‐butyl acrylate)) are first prepared by cationic ring‐opening polymerization and atom transfer radical polymerization, respectively. Well‐defined polymeric building blocks, ω‐N₃‐P(t‐BA) and α‐alkyne‐P(MOx), bearing reactive chain end groups, are accurately characterized by matrix‐assisted laser desorption ionization time‐of‐flight spectroscopy. Then, P(MOx)_n‐b‐P(t‐BA)_m are achieved by polymer–polymer coupling and are fully characterized by diffusion‐ordered NMR spectroscopy and size exclusion chromatography, demonstrating the obtaining of pure amphiphilic copolymers. Consequently, the latter lead to the formation in water of well‐defined monodisperse spherical micelles (R_H = 40–60 nm), which are studied by fluorescence spectroscopy, static light scattering, atomic force microscope, and transmission electronic microscopy. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Control of thermal properties and hydrolytic degradation in poly(lactic acid) polymer stars through control of isospecificity of polymer arms

The synthesis of a family of polymer stars with arms of varied tacticities is discussed. The effect of polymer tacticity on the physical properties of these polymer stars is dramatic. Dipentaerythritol cores support six poly(lactic acid) arms. Lewis acidic tin and/or aluminum catalysts control the polymerization to afford polymer stars of variable tacticity. Analysis of these polymers by ¹H NMR spectroscopy, thermogravimetric analysis, powder X‐ray diffraction, and differential scanning calorimetry reveals the effects of tacticity control on the physical properties of the polymer stars. Hydrolytic decomposition studies suggest that the degradation profile of a polymer star may also be tuned by stereochemical control. Differences between isotactic samples derived from rac‐lactide and L ‐lactide are heightened by longer arms of 50 and 100 monomer units. Control of polymer isospecificity shows that a ～70% isotacticity bias is necessary to induce crystallinity and alter the thermal and degradation properties of the material. Above 70% isotacticity, the degradation properties and thermal transitions can be further tuned across a relatively wide range. This technique allows for significant tunability to the physical properties of aliphatic polyester polymer stars. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparation of Stereoregular Isotactic Poly(mandelic acid) through Organocatalytic Ring‐Opening Polymerization of a Cyclic O‐Carboxyanhydride

Poly(mandelic acid) (PMA) is an aryl analogue of poly(lactic acid) (PLA) and a biodegradable analogue of polystyrene. The preparation of stereoregular PMA was realized using a pyridine/mandelic acid adduct (Py?MA) as an organocatalyst for the ring‐opening polymerization (ROP) of the cyclic O‐carboxyanhydride (manOCA). Polymers with a narrow polydispersity index and excellent molecular‐weight control were prepared at ambient temperature. These highly isotactic chiral polymers exhibit an enhancement of the glass‐transition temperature (T_g) of 15 °C compared to the racemic polymer, suggesting potential future application as high‐performance commodity and biomedical materials.     

Telechelic Poly(disulfide)s and Related Block Copolymer

In this communication, a mild, efficient, and generalized polycondensation route is developed for poly(disulfide)s from commercially available monomers 2,2′‐dithiodipyridine and 1,6‐hexanedithiol. Using the stoichiometric imbalance between the two monomers, it is possible to produce telechelic poly(disulfide)s of predictable molecular weight with reactive pyridyl disulfide groups at both the terminals of the chain. The two terminal pyridyl disulfide groups can be quantitatively replaced by a functional thiol using selective thiol‐disulfide exchange and thus produces functional telechelic poly(disulfide)s, which can be used as a macroinitiator to initiate ring‐opening poly­merization of a cyclic lactide monomer generating an ABA‐type triblock copolymer with degradable B block.