光纤激光器直接输出的高功率贝塞尔超短脉冲

构建了一种能够直接输出高功率贝塞尔超短脉冲的光纤激光放大器. 该方案基于在光纤端面特殊设计和制备的微型负轴锥镜, 针对常规超短脉冲光纤激光放大系统所设计, 不需要引入其他分立整形器件, 避免了目前基于轴锥透镜产生贝塞尔光束的通用方法所带来的额外烦琐准直工作, 极大简化了产生贝塞尔光束的方法. 其中的微型负轴锥镜由聚焦粒子束刻蚀法在一段掺镱大模场光子晶体光纤的端面制备, 它和光纤激光系统中的固有准直透镜构成了集成化的光束整形器件. 基于数值模拟结果成功搭建的系统与理论设计一致, 直接输出了在米量级具有高度准直无衍射特性的啁啾皮秒贝塞尔超短脉冲波包, 平均功率高达10.1 W, 对应脉冲能量178 nJ, 经过光栅对压缩后脉冲宽度可达140 fs. 关键词： 衍射 超短脉冲产生 光纤器件 光纤激光器     

All-normal-dispersion femtosecond fiber laser with pulse energy above 20 nJ

We report a study of the scaling and limits to pulse energy in an all-normal-dispersion femtosecond fiber laser. Theoretical calculations show that operation at large normal cavity dispersion is possible in the presence of large nonlinear phase shifts, owing to strong pulse shaping by spectral filtering of the chirped pulse in the laser. Stable pulses are possible with energies of tens of nanojoules. Experimental results from Yb-doped fiber lasers agree with the trends of numerical simulations. Stable and self-starting pulses are generated with energies above 20 nJ, and these can be dechirped to <200 fs duration. Femtosecond pulses with peak powers near 100 kW are thus available from this simple and practical design.     

皮秒光纤激光脉冲两个关键问题的研究

窄带耗散孤子锁模光纤激光器可以产生接近变换限制的皮秒脉冲,但受非线性相移的限制,输出脉冲重复频率不能通过增加腔长来降低,脉冲能量仅在0.1 nJ以下,严重制约着这类皮秒脉冲的实际应用。提出一种通过耦合器抽取腔内脉冲能量、抑制腔内非线性相移积累,进而允许增加腔长来降低窄带耗散孤子皮秒光纤激光脉冲重复频率的方法。运用该方法,成功地将激光器重复频率由35.2 MHz降低到了1.77 MHz,且脉冲时频特性保持不变。提出了一种基于级间FBG陷波滤波的抑制皮秒脉冲光纤放大中光谱展宽的方法。通过简单地使用级间陷波滤波器,既可窄化第一级光纤放大器后的输出脉冲谱宽,允许采用第二级光纤放大器进一步提升脉冲能量,而且,还可将脉冲重塑为近高斯形,利用高斯脉冲光谱展宽斜率小的特点,允许第二级光纤放大器将脉冲能量提升得更高。利用该方法,在RMS（均方值）谱宽保持0.4 nm以内的前提下,10 ps脉冲经标准单模光纤放大器后,能量可由0.2 nJ可提升到10 nJ以上。     

Enhanced red-shifted radiation by pulse trapping in photonic crystal fibers with two zero-dispersion wavelengths

A theoretical investigation on the two pulses copropagation and the red-shifted radiation generation in a photonic crystal fiber with two zero-dispersion wavelengths are presented. It is found the intensity of the red-shifted radiation components can be enhanced when the fiber is pumped with two pulses and the pulse trapping occurs. As the input peak power of the pump pulse is increased under the phenomenon of pulse trapping, the intensity of the red-shift radiation can be further enhanced. The above effects can be explained by the energy transfer from the Raman soliton to the red-shifted radiation components due to the effect of pulse trapping and the effect of higher-order dispersion.     

Double-clad fiber laser design for particle image velocimetry and material science applications

We have developed models to design actively Q-switched Yb-doped Double-Clad fiber lasers in various configurations. Based on these simulations, we present the design of two specific cavities: the first one is able to emit a pair of sub-nanosecond pulses separated by more than 500 ns for Particle Imagery Velocimetry applications. The time delay between the pulses can be adjusted by proper choice of the length of an un-doped fiber inserted in the cavity. The second cavity designed allows to emit long 150 ns pulses exceeding a few millijoules per pulse. Applications concern in this case materials science and combustion. In all cases, the rise time of the EOM is an essential parameter.     

基于耗散孤子种子的啁啾脉冲光纤放大系统输出特性

以不同滤波器带宽下获得的全正色散光纤激光器耗散孤子作为啁啾脉冲放大(CPA)系统的种子脉冲, 研究了光栅对和光纤展宽器CPA系统输出脉冲的可压缩性. 结果表明, 对于大能量耗散孤子种子脉冲, 当CPA系统采用正色散光纤展宽器时, 光纤群速色散与自相位调制之间的相互作用不仅可抑制耗散孤子脉冲光谱调制的影响, 还可使脉冲在光纤展宽器中自相似演化, 从而可提高CPA输出脉冲的可压缩性. 通过优化光纤展宽器长度, 对于耗散孤子种子源, 采用光纤展宽器的CPA系统输出脉冲可压缩性与主脉冲所占脉冲总能量之比均优于采用光栅对展宽器时的情况.     

Manipulating vector solitons with super-sech pulse shapes

Theoretical simulations about manipulating vector solitons with super-sech pulse shapes are conducted based on an optical fiber system. By changing the temporal pulses' parameters when the orthogonally polarized pulses have the same or different input central wavelengths, the output modes in orthogonal directions will demonstrate different properties. When the input orthogonal modes have the same central wavelength, the “2+2” pseudo-high-order vector soliton can be generated when the time delay is changed. While under the condition of different central wavelengths, orthogonal pulses with multiple peaks accompanied with two wavelengths can be achieved through varying the projection angle, time delay or phase difference. Our simulations are helpful to the study of optical soliton dynamics in optical fiber systems.     

Synchronization and coherent addition of three pulsed fiber lasers by mutual injection and phase modulation

The coherent beam addition of pulsed fiber lasers is an effective way to improve the average power and the peak pulse power. We demonstrate a new architecture based on mutual injection and phase modulation to generate synchronous pulsed fiber lasers. Firstly, we realize the synchronization of the pulses of three fiber lasers using this technique. Secondly, coherent addition of three synchronous pulsed fiber lasers is obtained. Experimental results show that the three fiber lasers are phase locked and have good temporal and spatial coherence under mutual injection locking. This method can be extended to combine more beams.     

High-energy femtosecond stretched-pulse fiber laser with a nonlinear optical loop mirror

A stretched-pulse fiber laser with a nonlinear optical loop mirror (NOLM) that produces 100-fs pulses with 1-nJ energy is demonstrated. These results constitute a 30-fold increase in pulse energy over previously reported femtosecond fiber lasers with a NOLM. Compared with previous stretched-pulse lasers, this laser offers a cleaner spectrum and improved stability, with comparable pulse duration and energy. Implications for the construction of truly environmentally stable lasers are discussed.     

High-energy, high-power ytterbium-doped Q-switched fiber laser

We report on a Q -switched, cladding-pumped, ytterbium-doped large-mode-area fiber laser operating at 1090 nm that is capable of generating 2.3 mJ of output pulse energy at a 500-Hz repetition rate and more than 5 W of average output power at higher repetition rates in a high-brightness beam (M(2) = 3) . Using a similar fiber with a smaller core, we generated >0.5-mJ pulses in a diffraction-limited beam. Our results represent a threefold increase in pulse energy over previously published values for Q-switched fiber lasers and firmly establish fiber lasers as compact, multiwatt, multimillijoule pulse sources with large scope for both industrial and scientific applications.     

High-energy soliton pulse generation with a passively mode-locked Er/Yb-doped multifilament-core fiber laser

We report the generation of high-energy short pulses from a mode-locked erbium/ytterbium-doped large-mode-area multifilament-core fiber laser operating in the purely anomalous dispersion regime. The self-starting fiber laser emits 400 mW of average output power at a pulse repetition rate of 44 MHz, corresponding to a pulse energy of 9.1 nJ. The laser produces near transform-limited output pulses with pulse duration of 1.6 ps, corresponding to 5 kW peak power. This new type of low-nonlinearity fibers demonstrates the power and energy scaling potential of fiber-based short pulse lasers in the eye-safe region.     

Tm:germanate fiber laser: tuning and Q-switching

A Tm:germanate fiber laser produced >0.25 mJ/ pulse in a 45 ns pulse. It is capable of producing multiple Q-switched pulses from a single pump pulse. With the addition of a diffraction grating, Tm:germanate fiber lasers produced a wide, but length dependent, tuning range. By selecting the fiber length, the tuning range extends from 1.88 to 2.04 μm. These traits make Tm:germanate lasers suitable for remote sensing of water vapor. PACS 42.55.Wd; 42.55.Xi     

Generation of 2-nJ pulses from a femtosecond ytterbium fiber laser

We report a mode-locked ytterbium fiber laser that generates femtosecond pulses with energies as large as 2.2 nJ. This represents a 20-fold improvement in pulse energy compared with that of previously reported femtosecond Yb fiber lasers. The laser produces pulses as short as 52 fs, which are to our knowledge the shortest pulses to date from a Yb fiber laser. The laser is diode pumped by a wavelength-division multiplexing coupler, which leads to excellent stability.     

氧化石墨烯被动锁模掺镱光纤激光器多脉冲现象的实验研究

利用氧化石墨烯作为可饱和吸收体,在被动锁模全正常色散掺镱光纤激光器中研究了多脉冲的现象,在同一抽运功率不同偏振态下,实验获得了矩形脉冲谐波锁模、耗散孤子谐波锁模、准谐波锁模,脉冲峰值周期性调制,脉冲簇、脉冲束、混沌多重脉冲的多脉冲现象,插入激光腔内的2nm窄带滤波器具有限制增益带宽、对脉冲塑形、诱导多脉冲产生的作用,调节偏振控制器相当于改变腔内增益,是实现不同类型多脉冲现象的主要原因,本实验研究有利于加深对多脉冲动力学行为在正常色散区域氧化石墨烯锁模掺镱光纤激光器中的理解。     

8 ns fiber laser Q switched by the resonant saturable absorber mirror

We demonstrate that resonant high-modulation-depth saturable absorbers allow efficient pulse shortening in Q-switched lasers. Using a 70% modulation depth resonant saturable absorber mirror we achieved 8 ns pulses that are close to the limit set by the cavity length and are, to our knowledge, the shortest pulses demonstrated to date from passively Q-switched fiber lasers.     

High-repetition-rate pulsed fiber laser based on virtually imaged phased array

High-repetition-rate(HRR) pulsed fiber lasers have attracted much attention in various fields. To effectively achieve HRR pulses in fiber lasers, dissipative four-wave-mixing mode-locking is a promising method. In this work, we demonstrated an HRR pulsed fiber laser based on a virtually imaged phased array(VIPA), serving as a comb filter. Due to the high spectral resolution and low polarization sensitivity features of VIPA, the 30 GHz pulse with high quality and high stability could be obtained. In the experiments, both the single-waveband and dual-waveband HRR pulses were achieved. Such an HRR pulsed fiber laser could have potential applications in related fields, such as optical communications.     

Coherence of supercontinua generated by ultrashort pulses compressed in optical fibers

Femtosecond fiber lasers together with nonlinear fibers are compact, reliable, all-fiber supercontinuum sources. Maintaining an all-fiber configuration, however, necessitates pulse compression in an optical fiber, which can lead to nonlinearities for subhundred femtosecond, nanojoule pulses. In this work we show that using large-mode-area fibers for pulse compression mitigates the nonlinearity, resulting in compressed pulses with significantly reduced satellite pulses. Consequently, supercontinua generated with these pulses are shown to have as much as a 10 dB increase in coherence fringe contrast. By using a hybrid highly nonlinear fiber-photonic crystal fiber, the continuum can be extended to visible wavelengths while still maintaining high coherence.     

Ultrafast pulse sources based on multi-mode optical fibers

Ultrafast pulse sources based on multi-mode optical fibers are discussed. High-power passively mode-locked fiber lasers based on multi-mode rare-earth-doped optical fibers greatly exceed the power limitations of single-mode oscillators. Ultrafast multi-mode fiber amplifiers operating in conjunction with multi-mode oscillators provide even higher power levels, where nonlinear propagation effects enable pulse compression to below 100 fs. Multi-mode fiber oscillators can be combined with single-mode Raman-shifting fibers to produce widely wavelength-tunable sources of femtosecond pulses. Further amplification in Yb fibers allows for the generation of sub-100-fs pulses with W-level average powers.     

全光纤激光器自启动锁模特性的理论研究

分析了带非线性放大光纤环的全光纤激光器的自启动锁模特性，得到了计算该激光器中光脉冲的有效能量增益的理论模型．结果表明，激光器的自启动锁模同掺Ｅｒ３＋光纤的增益及纤芯的有效截面积有关，并计算了自启动锁模的阈值峰值功率大小．应用本文的理论模型能成功地解释观察到的实验现象．