Multiresidue-matrix solid-phase dispersion method for determining 16 organochlorine pesticides and polychlorinated biphenyls in fish

Summary An effective, multiresidue-matrix, solid-phase dispersion — extraction (MSPD) and GC-MS method for the determination of 16 organochlorine pesticides (OCPs), as well as polychlorinated biphenyls (PCBs) from the level chlorination in fish is described. The method uses an octadecylsilyl-derivatized silica and Florisil-based MSPD co-column for direct, on-line clean-up. Recoveries calculated from five different fortification levels are >85% in all cases for OCPs, except for heptachlor and 4,4-DDT where recoveries of 78% and 81% are ob-tained, and >95% for PCBs. Detection limits determined for the OCPs vary from 19.6–91.1 ng g^–1, and from 71.4–111.2 ng g^–1 for the two to five chlorine-containing PCBs. The method has been applied to the analysis of fish grown in Er-Jen river (Taiwan) and method may serve as a screening protocol for the determination of OCPs and PCBs in fish.     

基质固相萃取-气相色谱电子捕获检测器同时测定大米中12种有机氯农药残留量

建立了大米中12种有机氯农药气相色谱-电子捕获检测器检测方法.采用基质固相分散(Matrix Solid Phase Disperse, MSPD)技术进行样品前处理, 用气相色谱-电子捕获检测器进行快速定性定量分析.基质固相分散集提取、过滤、净化于一步完成, 避免了样品均化、转溶、乳化、浓缩造成的待测农药组分的损失, 大大提高了方法的准确度和精密度.12种有机氯农药的添加回收率在83%～103%之间,相对标准偏差为2.2%～19%.     

Optimisation of a matrix solid-phase dispersion method for the determination of organophosphate compounds in dust samples

A fast and inexpensive sample preparation procedure based on the matrix solid-phase dispersion (MSPD) technique is proposed for the isolation of several organophosphate esters (mainly employed as flame retardants and plasticizers) from indoor dust samples. Extraction and clean-up were carried out in a single step and target compounds were determined by gas chromatography (GC) with nitrogen-phosphorus detection (NPD). The main parameters affecting extraction yield and selectivity, such as type and amount of dispersant material, clean-up co-sorbent and extraction solvent, were evaluated and optimised. Under final conditions, 0.5 g of dust were dispersed with equal amounts of anhydrous sodium sulphate and Florisil, and loaded on the top of a polypropylene cartridge containing 0.5 g of alumina. The dispersed sample was washed with 2 mL of n-hexane to remove the least polar interferences and analytes were eluted with 3 mL of acetone. Recoveries of the proposed method for spiked samples ranged from 80 to 116%, and the day-to-day variability remained between 5 and 10%. Data on levels of organophosphate species in dust from private houses and vehicle cabins are provided. In both cases, the lowest concentrations corresponded to the short chain, non-chlorinated, alkyl organophosphates, whereas mean values above 1 μg g⁻¹ were measured for the rest of analytes.     

Simultaneous determination of pyrethroid,organophosphate, and organochlorine pesticides in fish tissue using tandem solid-phase extraction clean-up

A method was developed for the simultaneous analysis of pyrethroid, organophosphate, and organochlorine pesticides in fish tissue. Different extraction solvents and solid-phase extraction clean-up procedures were tested. The best approach was to extract by sonication with acetonitrile and 10%?methanol, followed by clean-up of extracts using C₁₈, Florisil and Na₂SO₄ tandem solid-phase extraction cartridges. Gas chromatography with an electron-capture detector was used for analyte determination. All 26 target pesticides were detected using the new method in a single analytical run. The method detection limits ranged from 0.13 to 1.40?µg/kg, while recoveries of the analytes ranged from 86.1 to 133.8%?with relative standard deviations?≤12.1%?at a spiked concentration of 5?µg/kg. The method was developed to assess possible pesticide contamination in fish collected from lakes at a proposed Illinois National Guard Armory site.     

Development of a matrix solid-phase dispersion method for the determination of polycyclic aromatic hydrocarbons in sewage sludge samples

A new, single-step extraction and purification method based on matrix solid-phase dispersion (MSPD) was developed to determine 17 polycyclic aromatic hydrocarbons (PAHs) in sewage sludge samples. The MSPD method consists of sample homogenisation, exhaustive extraction and clean-up by a single process. The different operational parameters of the method, such as the type of dispersant, type and amount of additives, clean-up co-sorbent and extractive solvent were evaluated. Reversed-phase (C18) and polymeric (Oasis HLB and Oasis MAX) materials, as well as normal phase sorbents (Florisil, silica, neutral alumina) and an inert support (sand) were tested to assess the sorbents effect on the yield and selectivity of the MSPD process. Analysis of extracts was performed by high performance liquid chromatography (HPLC) coupled with fluorescence detection.Quantification limits obtained for all of these considered compounds (between 0.0001 and 0.005 μg g⁻¹ dry mass) were well below of the limits recommended in the EU. The extraction yields for the different compounds obtained by MSPD ranged from 76.3% to 103.6%. On the other hand, the extraction efficiency of the optimised method is compared with that achieved by microwave-assisted extraction and the method was applied to the analysis of real sewage sludge samples. A certified reference material (sewage sludge (BCR 088)) and a reference material (sewage sludge (RTC-CNS312-04)) were used to validate the proposed method.     

New method based on combining ultrasonic assisted miniaturized matrix solid-phase dispersion and homogeneous liquid-liquid extraction for the determination of some organochlorinated pesticides in fish

In this study, ultrasonic assisted miniaturized matrix solid-phase dispersion (US-MMSPD) combined with homogeneous liquid–liquid extraction (HLLE) has been developed as a new method for the extraction of organochlorinated pesticides (OCPs) in fish prior to gas chromatography with electron capture detector (GC-ECD). In the proposed method, OCPs (heptachlor, aldrin, DDE, DDD, lindane and endrin) were first extracted from fish sample into acetonitrile by US-MMSPD procedure, and the extract was then used as consolute solvent in HLLE process. Optimal condition for US-MMSPD step was as follows: volume of acetonitrile, 1.5 mL; temperature of ultrasound, 40 °C; time of ultrasound, 10 min. For HLLE step, optimal results were obtained at the following conditions: volume of chloroform, 35 μL; volume of aqueous phase, 1.5 mL; volume of double distilled water, 0.5 mL; time of centrifuge, 10 min. Under the optimum conditions, the enrichment factors for the studied compounds were obtained in the range of 185–240, and the overall recoveries were ranged from 39.1% to 81.5%. The limits of detection were 0.4–1.2 ng g⁻¹ and the relative standard deviations for 20 ng g⁻¹ of the OCPs, varied from 3.2% to 8% (n = 4). Finally, the proposed method has been successfully applied to the analysis of the OCPs in real fish sample, and satisfactory results were obtained.     

基质固相分散和GC-NCI-MS法分析果汁中拟除虫菊酯农药残留量

建立了基质固相分散法（MSPD）和气相色谱-负化学离子源-质谱法（GC—NCI—MS）应用于果汁中10种拟除虫菊酯农药残留量的快速分析方法，并对这些农药NCI—MS的阴离子结构与断裂机理进行初步探讨。采用以中性氧化铝为吸附刺、Florisil硅藻土为净化剂和乙酸乙酯为洗脱剂的MSPD样品前处理方法，以PCB103为内标物和GC—NCI—MS的选择离子监测方式（SIM）进行定性与定量分析。当样品的加标浓度水平为50、250μg／kg时，平均加标回收率为86．7％～114．8％，相对标准偏差为1.9％～14．1％；除氯菊酯农药的方法检出限（MDL）为14.7μg／kg外，其余农药的MDL大都小于1．0μg／kg；线性范围为10～500μg／kg，相关系数都大于0.997，在所分析的大部分果汁中至少分析出两种以上的拟除虫菊酯农药残留。     

An experimental design approach employing artificial neural networks for the determination of potential endocrine disruptors in food using matrix solid-phase dispersion

Matrix solid-phase dispersion (MSPD) as a sample preparation method for the determination of two potential endocrine disruptors, linuron and diuron and their common metabolites, 1-(3,4-dichlorophenyl)-3-methylurea (DCPMU), 1-(3,4-dichlorophenyl) urea (DCPU) and 3,4-dichloroaniline (3,4-DCA) in food commodities has been developed. The influence of the main factors on the extraction process yield was thoroughly evaluated. For that purpose, a 3^(4–1) fractional factorial design in further combination with artificial neural networks (ANNs) was employed. The optimal networks found were afterwards used to identify the optimum region corresponding to the highest average recovery displaying at the same time the lowest standard deviation for all analytes. Under final optimal conditions, potato samples (0.5 g) were mixed and dispersed on the same amount of Florisil. The blend was transferred on a polypropylene cartridge and analytes were eluted using 10 ml of methanol. The extract was concentrated to 50 μl of acetonitrile/water (50:50) and injected in a high performance liquid chromatography coupled to UV–diode array detector system (HPLC/UV–DAD). Recoveries ranging from 55 to 96% and quantification limits between 5.3 and 15.2 ng/g were achieved. The method was also applied to other selected food commodities such as apple, carrot, cereals/wheat flour and orange juice demonstrating very good overall performance.     

Trends and recent applications of matrix solid-phase dispersion

Matrix solid-phase dispersion (MSPD) is a sample-preparation technique with increasing acceptance in trace analysis of organic compounds using chromatographic and electro-driven separation techniques. It has been applied to the extraction and fractionation of a large number of substances from solid, semi-solid, and liquid matrices. Low sample and solvents consumption, straightforward application, and reduced cost, and its ability to simultaneously perform extraction and clean-up in a single step, are some of its major advantages. This review attempts to provide an updated, concise and critical overview on the latest trends and applications of MSPD, placing emphasis on comparison of its performance with that of other techniques, besides focusing on practical features to take into account depending on the nature of the sample and the properties of the analytes. Achievements, advantages, and limitations are discussed. The paper also highlights future challenges to be faced.     

Development of an analytical method based on microwave-assisted extraction and solid phase extraction cleanup for the determination of organochlorine pesticides in animal feed

A method to determine 21 organochlorine pesticides in animal feed samples using microwave assisted extraction and solid phase extraction cleanup was optimised regarding its main parameters. After extraction with hexane-acetone (50:50), three different sorbents (alumina/ENVI-Florisil, ENVI-Carb and ENVI-Carb II/PSA) were assayed for the cleanup step. Analytes were eluted with hexane-ethyl acetate (80:20) and determined by gas chromatography and electron capture detection followed by gas chromatography-mass spectrometry. ENVI-Carb and ENVI-Carb II/PSA provided colourless eluates but fewer interferent compounds were found in ENVI-Carb II/PSA chromatograms, so this system was selected to carry out the purification of the extracts. The analytical recoveries obtained with this method were close to 100% in most cases with relative standard deviations lower than 10%. These percentages were similar to those obtained with the Soxhlet extraction procedure, which shows the method suitable for the determination of organochlorine pesticides in animal feed material. The method was also validated with the analysis of a certified reference material (CRM-115 BCR), and the results obtained were in good accordance with the certified values.     

On-line determination of organochlorine pesticides in water by solid-phase microextraction and gas chromatography with electron capture detection

This paper describes the extraction of 20 organochlorine pesticides (OCPs) from water samples using solid-phase microextraction (SPME). Three fused-silica fibers coated or bonded with polydimethylsiloxane (PDMS) of different film thicknesses (20-, 30-, and 100-μm) were evaluated. The extraction time, the effects of stirring and addition of NaCl to the aqueous sample, the linear range and the precision of this technique, and the effect of carryover were examined for 20 analytes and are presented here. A comparison with results using conventional liquid-liquid extraction demonstrate that the SPME technique is well suited as a fast screening technique for OCPs in water samples.     

固相萃取法与基质固相分散法在橙子中有机磷农药残留分析中的应用

建立了固相萃取(SPE)-反相高效液相色谱(RP-HPLC)同时测定橙子中痕量辛硫磷、二嗪农有机磷农药残留量的方法。样品经甲醇超声提取、C18固相萃取柱净化后,采用液相色谱柱分离,以乙腈-水(体积比为85∶15)为流动相等度洗脱,于254 nm下紫外检测。结果表明:在0.1～10.0 mg/L和0.4～10.0 mg/L范围内,辛硫磷、二嗪农的质量浓度与峰面积呈良好的线性关系;样品的加标平均回收率为87.3%～102.7%,相对标准偏差(RSD)为0.9%～4.9%。将该分析结果与用基质固相分散法(MSPD)处理样品所得的结果相比较,发现SPE对二嗪农的提取效果较好,而MSPD对辛硫磷的提取效果较好,但两种方法都能较好地净化样品,均能满足残留量的分析要求。     

底物固相分散法测定土壤中甲氰菊酯残留量

以甲氰菊酯为分析对象，将一种新型的样品预处理技术-底物固相分散法(MSPD)应用于测定土壤中农药残留。确定了MSPD法的实验条件：土壤量为4g，水的加入量为1mL，固相吸附剂弗罗里硅土的用量为10．0g，淋洗剂为15mL石油醚-乙酸乙酯(1 9)。土壤样品在此条件下处理后无需进一步净化即可用气相色谱／电子捕获检定器测定。三种土壤的三种加标水平的回收率均在90％以上，相对标准偏差小于5％(n＝5)，最小检出质量比为0．002mg/kg。     

Optimisation of solid-phase microextraction coupled to HPLC-UV for the determination of organochlorine pesticides and their metabolites in environmental liquid samples

A solid-phase microextraction (SPME) procedure using two commercial fibers coupled with high-performance liquid chromatography (HPLC) is presented for the extraction and determination of organochlorine pesticides in water samples. We have evaluated the extraction efficiency of this kind of compound using two different fibers: 60-μm polydimethylsiloxane–divinylbenzene (PDMS-DVB) and Carbowax/TPR-100 (CW/TPR). Parameters involved in the extraction and desorption procedures (e.g. extraction time, ionic strength, extraction temperature, desorption and soaking time) were studied and optimized to achieve the maximum efficiency. Results indicate that both PDMS-DVB and CW/TPR fibers are suitable for the extraction of this type of compound, and a simple calibration curve method based on simple aqueous standards can be used. All the correlation coefficients were better than 0.9950, and the RSDs ranged from 7% to 13% for 60-μm PDMS-DVB fiber and from 3% to 10% for CW/TPR fiber. Optimized procedures were applied to the determination of a mixture of six organochlorine pesticides in environmental liquid samples (sea, sewage and ground waters), employing HPLC with UV-diode array detector.     

A toxic reagent-free method for normal-phase matrix solid-phase dispersion extraction and reversed-phase liquid chromatographic determination of aldrin,dieldrin, and DDTs in animal fats

A method for the determination of aldrin, dieldrin, DDT, DDE, and DDD contamination in animal fats (beef tallow, lard, and chicken fat) without using toxic reagents is developed, that uses high-performance liquid chromatography after the sample has been prepared by matrix solid-phase dispersion (MSPD) with acidic alumina oxide. A reversed-phase C₁-silica column with a mobile phase of 50% (v/v) ethanol solution (in water) and a photo-diode array detector were used for the determination. Average recoveries of the target compounds (0.2–5.0 g g^–1) ranged from 84–98%, with coefficients of variation of <5%. The limits of quantitation were 0.16 g g^–1 for AD, 0.10 g g^–1 for DD, 0.06 g g^–1 for DDT, 0.07 g g^–1 for DDE, and 0.05 g g^–1 for DDD. No toxic reagents were used at all.     

Determination of organophosphorus pesticides in bovine tissue by an on-line coupled matrix solid-phase dispersion-solid phase extraction-high performance liquid chromatography with diode array detection method

A miniaturized method based on matrix solid-phase dispersion coupled to solid phase extraction and high performance liquid chromatography with diode array detection (MSPD-SPE-HPLC/DAD) was developed for the trace simultaneous determination of the following organophosphorus pesticides (OPPs) in bovine tissue: parathion-methyl, fenitrothion, parathion, chlorfenvinphos, diazinon, ethion, fenchlorphos, chlorpyrifos and carbophenothion. To perform the coupling between MSPD and SPE, 0.05 g of sample was dispersed with 0.2 g of C(18) silica sorbent and packed into a stainless steel cartridge containing 0.05 g of silica gel in the bottom. After a clean-up of high and medium polarity interferences with water and an acetonitrile:water mixture, the OPPs were desorbed from the MSPD cartridge with pure acetonitrile and directly transferred to a dynamic mixing chamber for dilution with water and preconcentration into an SPE 20 mm × 2.0 mm I.D. C(18) silica column. Subsequently, the OPPs were eluted on-line with the chromatographic mobile phase to the analytical column and the diode array detector for their separation and detection, respectively. The method was validated and yielded recovery values between 91% and 101% and precision values, expressed as relative standard deviations (RSD), which were less than or equal to 12%. Linearity was good and ranged from 0.5 to 10 μg g(-1), and the limits of detection of the OPPs were in the range of 0.04-0.25 μg g(-1). The method was satisfactorily applied to the analysis of real samples and is recommended for food control, research efforts when sample amounts are limited, and laboratories that have ordinary chromatographic instrumentation.     

A simple; efficient and environmentally friendly method for the extraction of pesticides from onion by matrix solid-phase dispersion with liquid chromatography-tandem mass spectrometric detection

An evaluation of the extraction of pesticides from onion by matrix solid-phase dispersion (MSPD) with the determination by liquid chromatography tandem mass spectrometry using electrospray as the ionization source (LC-ESI-MS/MS) was carried out. The performance of different sorbents, including reused C18 bonded silica, was evaluated. Different parameters affecting the extraction efficiency were evaluated, such as the type and amount of sorbent, the time of interaction after the fortification step, the time of sample dispersion and the elution solvent. The matrix effect regarding the recovery of the pesticides by MSPD was also investigated. The best results were obtained using 0.5 g of sample, 1.0 g reused C18, interaction time of 1 h, dispersion time of 5 min, and acetonitrile as the elution solvent. The method was validated by the fortification of the onion sample, free of pesticides, at different concentration levels (0.01, 0.1 and 1.0 mg kg⁻¹). Average recoveries ranged from 78.3 to 120.4% and relative standard deviation below 20% was obtained. Detection and quantification limits ranged from 0.003 to 0.03 mg kg⁻¹ and from 0.01 to 0.1 mg kg⁻¹, respectively.     

Determination of suspected fragrance allergens in cosmetics by matrix solid-phase dispersion gas chromatography-mass spectrometry analysis

An effective low cost sample preparation methodology for the determination of regulated fragrance allergens in leave-on and rinse-off cosmetics has been developed applying, for the first time, matrix solid-phase dispersion (MSPD) to this kind of analytes and samples. The selection of the most suitable extraction conditions was made using statistical tools such as ANOVA, as well as a factorial multifactor experimental design. These studies were carried out using real cosmetic samples. In the final conditions, 0.5 of sample, previously mixed with 1g of anhydrous Na(2)SO(4), were blended with 2g of dispersive sorbent (Florisil), and the MSPD column was eluted with 5 mL of hexane/acetone (1:1). The extract was then analyzed by GC-MS without any further clean-up or concentration step. Accuracy, precision, linearity and detection limits (LODs) were evaluated to assess the performance of the proposed method. Quantitative recoveries (>75%) were obtained and RSD values were lower than 10% in all cases. The quantification limits were well below those set by the international cosmetic regulations, making this multi-component analytical method suitable for routine control. In addition, the MSPD method can be implemented in any laboratory at low cost since it does not require special equipment. Finally, a wide variety of cosmetic products were analyzed. All the samples contained several of the target cosmetic ingredients, with and average number of seven. The total fragrance allergen content was in general quite high, even in baby care products, with values close to or up to 1%, for several samples, although the actual European Cosmetic Regulation was fulfilled.     

Optimization of matrix solid-phase dispersion conditions for organic fungicides determination in soil samples

A simplified sample preparation method, based on the matrix solid-phase dispersion technique, is proposed for the sensitive determination of 15 organic fungicides in vineyard soils by gas chromatography-mass spectrometry (GC-MS). Under final working conditions, sieved samples (0.5 g) were blended and dispersed with 2 g of C18 and transferred to a polypropylene syringe containing 1 g of diatomaceous earth. Analytes were recovered using 10 mL of ethyl acetate, this extract was concentrated to 1 mL and fungicides determined by GC-MS, without additional cleanup. The method provided recoveries in the range from 74 to 122% for soils with total carbon contents up to 5.5% and it allowed the use of external standard as quantification technique. Inter-day precision, given as relative standard deviations, stayed between 3 and 13%, and the limits of quantification were comprised between 0.6 and 15 ng g(-1). Several fungicides were found in the top layer of vineyard soils with the highest detection frequency and maximum concentration corresponding to iprovalicarb. Some real samples were also submitted to pressurized liquid extraction. Measured concentrations were in excellent agreement with those obtained by matrix solid-phase dispersion, which reinforces the accuracy of the latter methodology.     

Comparison of different extraction techniques for the determination of chlorinated pesticides in animal feed

The performances of Soxhlet extraction, dive-in Soxhlet extraction, microwave-assisted extraction (MAE), accelerated solvent extraction (ASE), fluidized-bed extraction (FBE), and ultrasonic extraction (UE) for the analysis of organochlorine pesticides in animal feed have been investigated. ASE and MAE provided significantly better extraction efficiency than Soxhlet extraction. The concentrations were 126.7 and 114.8%, respectively, of the values obtained by classical Soxhlet extraction, whereas the results from FBE and dive-in Soxhlet were comparable with those from the standard Soxhlet procedure. The reproducibility of FBE was the best, with RSDs ranging from 0.3 to 3.9%. Under the investigated operation conditions UE was not efficient, with the recoveries of target compounds being about 50% less than Soxhlet. Additionally, the performances of Soxhlet, dive-in Soxhlet, MAE, ASE and FBE were validated by determination of the certified reference material BCR-115. The results from the extraction techniques were in good agreement with the certified values.