Improvement of thermal decomposition properties of ammonium perchlorate particles using some polymer coating agents

This research aimed to investigate the optimum conditions for modification of thermal decomposition properties of ammonium perchlorate (AP) particles through microencapsulation techniques. A solvent/non-solvent method has been used to perform microencapsulation of AP particles with some polymer-coating agents such as viton A and nitrocellulose (NC). Differential scanning calorimetry, thermogravimetry, and scanning electron microscopy have been exploited to investigate the thermal properties, heat of decomposition, and coating morphology of pure and coated samples. The preliminary results revealed that AP microparticle could be effectively coated with both NC and viton, but the latter significantly and unfavorably attenuated heat of decomposition of AP so NC was chosen as an appropriate coating agent for modification of thermal properties of AP. The thermal analysis of NC-coated samples, prepared at optimized coating conditions, showed that its first stage decomposition temperature increases about 12 °C with respect to uncoated sample and reaches to 305 °C. Also, the apparent activation energy (E), ΔG ^≠, ΔH ^≠, and ΔS ^≠ of the decomposition processes of the pure and coated AP particles at the optimum conditions were obtained by non-isothermal methods that proposed by ASTM and Ozawa. Finally, the results of this investigation showed that microencapsulation of AP particles with fibrous NC enhance its heat of decomposition (~120 J g^?1) with no obvious effect on kinetic parameters and thermal decomposition temperature.     

Obtaining nanocomposites of polyamide 6 and cellulose whiskers via extrusion and injection molding

Nanocomposites of polyamides with cellulose whiskers are difficult to obtain by conventional processing of extrusion and injection molding because of the low thermal stability of the cellulosic nanostructures and the relatively high processing temperature of polyamides, which is higher than the temperature of thermal degradation of cellulose whiskers. Thus, in this study cellulose whiskers were coated with polyamide 6 (PA6) in order to increase their thermal stability and prevent the formation of agglomerates. This coating on cellulose whiskers allows their application to obtain nanocomposites with polyamides, whose processing temperatures are relatively high, around 250 °C. Cellulose whiskers (CWs) were obtained from cotton fibers by acid hydrolysis. The freeze-dried CWs were coated with PA6 by dispersing them in formic acid; PA6 was solubilized in this suspension. The cellulose-coated whiskers (CCWs) were characterized by X-ray diffraction, differential scanning calorimetry (DSC), thermogravimetry (TG), scanning electron microscopy (SEM-FEG) and infrared spectroscopy. SEM-FEG and TG results showed that the PA6 coating on CWs prevented high agglomeration of dried CWs and promoted an increase in their thermal stability from 180 to 280 °C, allowing the use of CCWs to obtain nanocomposites with PA6 using conventional processing routes, such as extrusion and injection molding, at appropriate processing temperatures. In this way, 1 wt% CCWs was used to prepare nanocomposites with PA6. The PA6 + 1CW nanocomposites were compared to neat PA6 without CWs. The samples were characterized by tensile tests and DSC, and the results showed that the PA6 coating on CWs was effective in raising the thermal stability of CWs, improving the dispersion of CWs in the matrix of PA6, resulting in a 45 % increase in the elastic modulus of the nanocomposite with only 1 wt% of coated cellulose whiskers in comparison to neat PA6.     

Ultrathin polydimethylsiloxane-coated carbonyl iron particles and their magnetorheological characteristics

An ultrathin polydimethylsiloxane (PDMS) layer with a mean thickness of 1 nm was coated on soft magnetic carbonyl iron (CI) particles by using a simple thermal evaporation process, and then their physical characteristics were examined using scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), thermal gravimetry analysis (TGA), and vibrating sample magnetometry (VSM). Magnetorheological (MR) fluid was prepared by using PDMS-coated CI powder, and its rheological behavior was investigated under different external magnetic field strengths using a rotational rheometer. The CI particles coated by a thin PDMS layer showed higher oxidation temperature than pristine CI particles and MR fluid consisting of PDMS-coated CI particles demonstrated better dispersion stability in a nonmagnetic carrier fluid.     

Examination of Zinc coatings on Copper substrates by thermal analysis

Copper has excellent thermal conductivity and is mainly applied in electrical and machinery applications. Its main disadvantage is its poor resistance in aggressive environments which can be significantly enforced by the deposition of Zinc coatings. In this study the effect of the deposition time and temperature on the thickness and microstructure of Zinc coatings on Copper substrates by pack cementation process using a DSC apparatus, is investigated. Moreover, the oxidation performance of the coated samples has been evaluated in a high-temperature environment. Oxidation tests were accomplished by thermogravimetric measurements while the coated and oxidized samples were examined with SEM microscopy and XRD diffraction analysis. DSC results revealed that the chemical reactions, which lead to the coating formation, take place up to 300 °C while the coating thickness increases with the duration of the deposition process. The as formed coatings consist of two layers corresponding to different Cu–Zn phases. Finally the coated samples were found to be more resistant when exposed in the aggressive environment, as they begin to oxidize at significant higher temperatures than the uncoated samples. This can mainly attributed to the formation of ZnO on the surface of the coating.     

化学气相反应法制备不同碳基体表面SiC涂层组织结构分析

采用化学气相反应法, 以同种工艺分别在石墨和C/C复合材料表面制备了SiC涂层, 借助X射线衍射仪(XRD)、扫描电镜(SEM)及能谱分析等手段分析了涂层的微观结构, 研究了不同碳基体对SiC涂层结构和表面形貌的影响, 并初步对比考察了涂层的高温抗氧化性能. 结果表明: 制备的SiC涂层整体致密, 与基体结合良好, 但存在明显的结构差异. 石墨表面制得的SiC涂层呈梯度分布, 涂层主要由致密外层及过渡内层组成, 而C/C复合材料表面制得的SiC涂层仅由致密外层组成; 在1823 K的空气氧化氛围中, 与C/C复合材料SiC涂层试样相比, 石墨SiC涂层试样表现出更好的高温抗氧化性能, 经30 h氧化及7次循环热震实验后, 涂层试样的氧化失重率仅为0.182%.     

Effects of atomization surfaces and modifiers on the electrothermal atomization of cadmium

Atomization of cadmium on tungsten carbide, molybdenum carbide and metallic palladium coated platforms and on pyrolytic graphite coated platforms with and without tungsten, molybdenum and palladium modifiers has been studied. A physical vapour deposition method is used for coating. A high thermal stability, a greater appearance temperature and a decrease in sensitivity are found when compared with atomization on conventional platforms. Diffusion and kinetic parameters are obtained using different models. More than one activation energy (E_a) and frequency factor (v) are obtained depending on the atomization temperature while the atomic vapour appears. These results may indicate that more than one formation process is simultaneously present or that the evolution from one formation process to another is temperature dependent. Greater values of E_a and v are found during atomization on the molybdenum carbide coated platform and when molybdenum or palladium modifiers are used. This may suggest that strong cadmium-metal interaction is present. This strong interaction is not present when palladium is used as a metallic coating, although a similar trend in thermal stability is observed. The contribution of the expansion to the atomic vapour dissipation is also evaluated.     

Influence of polymeric coating on capillary electrophoresis of iron oxide nanoparticles

In this work, electrophoresis was successfully used to separate three different polymer-coated magnetic iron oxide nanoparticles with similar sizes (nominally 50 nm) using high-pH borate buffer system. The coating polymers were dextran, polyethylene glycol, or carboxymethyl dextran. The results showed that the migration time of carboxymethyl dextran coated nanoparticles is the longest due to relatively more negative surface charges. Investigation of the effects of buffer concentration, pH, electric field strength and the capillary temperature, on electrophoretic properties of samples was also carried out. The results showed that pH, electric field strength and the capillary temperature had indirect relations with both of the migration time and the separation resolution of three different polymer-coated nanoparticles while the buffer concentration had a direct relation.     

Corrosion-resistant coating of iron: A synergistic effect of electroactive poly(triphenylamine) coating with posttreatment for high-corrosion-protection efficiency

AbstractAn electroactive poly(triphenylamine) (PTPA-C6) is applied to the surface of iron as a corrosion-protection layer. The iron substrate coated with PTPA-C6 is thermally treated at different temperatures (up to 80°C) to study the effect of thermal treatment of PTPA-C6 on the corrosion behavior of iron. Experimental results indicate that the contact angle of the PTPA-C6 film increases from 81.6° at room temperature to 100° after thermal treatment at 80°C for 1 hr. The surface becomes more hydrophobic after thermal treatment, which will lower the penetration of water to the iron surface. Adhesion tests (ASTM 3359) indicate that adhesion between the PTPA-C6 and iron substrate is enhanced after thermal treatment. Additionally, a thin iron oxide layer formed between the PTPA-C6 and iron substrate as a passivation layer. The synergistic effect of these factors makes PTPA-C6 a very effective corrosion protection layer on iron substrate after appropriate thermal treatment. Corrosion protection efficiency increases from 90% of the pristine PTPA-C6 to 99.9% of the 80°C treated PTPA-C6.     

Photocatalytic TiO2 coatings on limestone

The application of photocatalytic coatings on stone has been investigated for providing surface protection and self-cleaning properties. Sol–Gel and hydrothermal processes were used to synthesise TiO₂ colloidal suspensions and coatings with enhanced photocatalytic activity without any thermal curing of the coated stone. The stone was a porous limestone (apulian sedimentary carbonatic, calcite stone). Films and powders prepared from TiO₂ sols were studied using X-ray diffraction to evaluate the microstructure and identify rutile and anatase phases. A morphological and physical characterisation was carried out on coated and uncoated stone to establish the changes of appearance, colour, water absorption by capillarity and water vapour permeability. The photocatalytic activity of the coated surface was evaluated under UV irradiation through NO _x and organics degradation tests. The performances of the synthesised TiO₂ sols were compared with commercial TiO₂ suspension. Since the coating doesn’t need temperature treatments for activating the photocatalytic properties, the nano-crystalline hydrothermal TiO₂ sols seem good candidate for coating applications on stone that cannot be annealed after the coating application.     

Coating of polyamide 12 by sol–gel methodology

The combination of sol–gel methodology with rapid prototyping (RP) produces functionalized 3D structures with potential applications in various fields. However, this combination has been little explored. In this paper, we used the sol–gel method to deposit vanadium isopropoxide onto polyamide (PA12) constructed by RP and pretreated with acetic acid, to obtain a functionalized substrate with new thermal, physical, and chemical properties. Vanadium isopropoxide (one, five, or ten layers) was deposited onto the PA12 piece by dip-coating. We characterized the coated PA12 by thermal analyses, X-ray diffraction, and infrared spectroscopy, which revealed that V=O and Si–O–Si groups exist on the PA12 surface. PA12 coating with vanadium isopropoxide enhanced the decomposition temperature. Differential scanning calorimetry revealed increased fusion and decomposition enthalpy as a function of the PA12 coating. Therefore, deposition of vanadium isopropoxide onto PA12 pretreated with acetic acid improves the thermal stability of PA12 prepared by RP.     

A sol‐gel based solid phase microextraction fiber for the analysis of aliphatic alcohols in apple juices

A new fiber based on titania‐chitin sol‐gel coated on a silver wire for the headspace solid phase microextraction of aliphatic alcohols from apple juice samples was developed. The influences of fiber coating composition and microextraction conditions (extraction temperature, extraction time, and ionic strength of the sample matrix) on the fiber performance were investigated. Also, the influence of temperature and time on desorption of analytes from fiber were studied. Under the optimized conditions, a porous fiber with a high extraction capacity and good thermal stability (up to 250°C) was obtained. The proposed headspace solid‐phase microextraction‐GC method was successfully used for the analysis of aliphatic alcohols in apple juice and concentrate samples. The recovery values were from 92.8 to 98.6%. The RSD (n=5) for all analytes were below 7.8%.     

Tribo-corrosion behavior of Zn-Ni-Cu and Zn-Ni-Cu-TiB2 coated mild steel

In this investigation , Zn-Ni-Cu and Zn-Ni-Cu-TiB₂ were coated on a mild steel specimen using a high velocity oxy fuel thermal spray (HVOF) process. The surface morphology and coated powder distribution of coated specimens were characterized using scanning electron microscope (SEM), energy dispersive spectroscopy (EDS), and X-ray-Elemental mapping. The pin-on-disc (ASTM G99-17) method was used to examine the wear resistance of the coated and uncoated mild steel specimens. Both coated Zn-Ni-Cu and Zn-Ni-Cu-TiB2 on mild steel saw reduced wear volume loss than uncoated mild steel. The coated samples of Zn-Ni-Cu and Zn-Ni-Cu-TiB2 on Mild Steel were put through a scratch test to determine the adhesion strength of the coating with the substrate. The adhesion strength of coated Zn-Ni-Cu and Zn-Ni-Cu TiB2 mild steel was higher than that of untreated mild steel, indicating a solid link between the coating and substrate and minimal delamination. Using the Vickers hardness test to measure the hardness caused by the coating, it was shown that coated samples of Zn-Ni-Cu and Zn-Ni-Cu-TiB2 coated mild steel had significantly higher hardness than uncoated mild steel. Using ASTM G1-03 and ASTM G-31 standards, a 0.2 M HCl immersion cycle test was conducted for 28 days to test the corrosion resistance of coatings in an acidic media (672Hrs). When compared to Zn-Ni-Cu and Zn-Ni-Cu-TiB2 coated mild steel, the weight loss for the uncoated mild steel was significantly larger. Additionally, XRD examination showed that coated samples had less rust on their surface than uncoated samples. Both Zn-Ni-Cu and Zn-Ni-Cu-TiB2 on Mild Steel were anti-corrosive, as evidenced by increased corrosion potential and reduced corrosion current density when compared to uncoated mild steel, according to electrochemical impedance spectroscopy (EIS)/Tafel study in 0.2 MHCl. The outcomes of each test were very encouraging and demonstrated the durability of these coatings against wear and corrosion.     

β-cyclodextrin-bonded silica particles as novel sorbent for stir bar sorptive extraction of phenolic compounds

A stir bar coated with β-cyclodextrin-bonded-silica (CDS) as novel sorbent has been developed and used to analyze seven phenolic compounds in aqueous samples, followed by thermal desorption and gas chromatography-mass spectrometric detection. Significant parameters affecting sorption process such as the time and temperature of sorption and desorption, ionic strength, pH and stirring rate have been optimized and discussed. The coating has a high thermal stability up to 300°C and long application lifetime (80 times). The porous structure of CDS coating provides high surface area and allows high extraction efficiency. Under the selected conditions, linearity range of 0.1-400 μg/L, limit of quantifications of 0.08-3.3 μg/L and method detection limits of 0.02-1.00 μg/L have been obtained. A satisfactory repeatability (RSD ≤ 6.5, n = 7) with good linearity (0.9975 ≤ r(2) ≤ 0.9996) of results illustrated a good performance of the present method. The recovery of different natural water samples was higher than 81.5%.     

Improvement of the thermo-oxidative stability of low-density polyethylene films by organic-inorganic hybrid coatings

LDPE films have been coated with single or bi-layer hybrid coatings formed through sol-gel reactions in order to improve their thermo-oxidative resistance. Different chemical compositions of the coating were investigated which differ either in the amount of the inorganic phase (silica deriving from tetraethoxysilane) or in the organic component (either alkoxy silane functionalized polyethylene-poly(ethylene glycol) diblock copolymers or poly(vinyl alcohol)). The thermo-oxidative stability of the coated films thus obtained has been assessed by means of isothermal differential scanning calorimetry (DSC) and isothermal thermo-gravimetric analysis (TGA) under accelerated conditions, i.e. at high temperatures in pure oxygen flow. Conventional ageing in air at lower temperature, slightly above the in-service one, has also been carried out. The obtained data show: a) a general improvement of the thermal-resistance for the coated LDPE samples; b) a particularly high thermal-resistance for LDPE coated with a bi-layer coating with pure silica in the top layer; c) the effectiveness of the accelerated techniques in qualitatively assessing the thermo-oxidative resistance of the coated polymeric systems.     

采用溶胶-凝胶技术涂层的新型固相微萃取方法及其应用

将溶胶-凝胶技术应用于SPME固相涂层的制备,涂制的端羟基-聚二甲基硅氧烷固相涂层热稳定性好,萃取时间和解吸时间短,对极性化合物及非极性化合物均有较强的萃取富集能力。扫描电镜图显示涂层表面为多孔结构。采用该涂层的SPME方法在对环境样品的分析中获得了令人满意的效果。     

Molecularly imprinted stir bars for selective extraction of thiabendazole in citrus samples

Stir‐bar sorptive extraction is based on the partitioning of target analytes between the sample (mostly aqueous‐based liquid samples) and a stationary phase‐coated magnetic stir bar. Until now, only PDMS‐coated stir bars are commercially available, restricting the range of applications to the non‐selective extraction of hydrophobic compounds due to the apolar character of PDMS. In this work, a novel stir bar coated with molecularly imprinted polymer as selective extraction phase for sorptive extraction of thiabendazole (TBZ) was developed. Two different procedures, based on physical or chemical coating, were assessed for the preparation of molecularly imprinted stir bars. Under optimum conditions, recoveries achieved both in imprinted and non‐imprinted polymer stir bars obtained by physical coating were very low, whereas TBZ was favourably retained by imprinted over non‐imprinted polymer stir bars obtained by chemical coating and thus the latter approach was used in further studies. Different parameters affecting both stir‐bars preparation (i.e. cross‐linker, porogen, polymerization time) and the subsequent selective extraction of TBZ (i.e. washing, loading and elution solvents, extraction time) were properly optimized. The molecularly imprinted coated stir bars were applied to the extraction of TBZ from citrus samples (orange, lemon and citrus juices) allowing its final determination at concentrations levels according to current regulations.     

A molecularly imprinted polymer-coated nanocomposite of magnetic nanoparticles for estrone recognition

In this study, we synthesized Fe₃O₄ magnetic nanoparticles coated estrone-imprinted polymer with controlled size using a semi-covalent imprinting strategy. In this protocol, the estrone-silica monomer complex (EstSi) was synthesized by the reaction 3-(triethoxysilyl)propyl isocyanate with estrone, where the template was linked to the silica coating on the iron oxide core via a thermally reversible bond. The removal of the template by a simple thermal reaction produced specific estrone recognition sites on the surface of silica shell.The resulting estrone-imprinted polymer coating Fe₃O₄ magnetic hybrid nanoparticles exhibit a much higher specific recognition and saturation magnetization. The hybrid nanoparticles have been used for biochemical separation of estrone.     

The effect of cerium pre-treatment on the corrosion resistance of steel sheets

The steel samples have been coated with cerium layer by cathodic electrolytic deposition from the Ce(NO₃)₃·6H₂O solution in aqueous ethyleneglycol in the presence of hydrogen peroxide. The influence of the coating parameters (cathodic current density, pH, cerium concentration, hydrogen peroxide concentration, temperature, and treatment duration) on the surface properties; the optimum conditions of the formation of corrosion preventing coating have been elucidated. Hydrogen peroxide concentration and pH are the major factors influencing the deposition process. The corrosion resistance has been further enhanced after treatment with Na₃PO₄·12H₂O solution. The cerium-coated samples have been subsequently coated by cathodic electrostatic deposition from the colloidal solution of the paint. The coated materials have been subjected to mechanical testing (hardness, impact, cross cut, bending, and cupping tests), and their structure has been visualized by electron microscopy. The cerium coating has been found to improve the steel corrosion resistance by 15%.     

添加碳纳米管对钌铱锡氧化物阳极性能的影响

本文采用热分解法制备Ti/Ru-Ir-Sn氧化物阳极,运用TGA、SEM、EDS、循环伏安、电化学交流阻抗、极化曲线以及强化电解寿命测试方法,探讨添加不同含量碳纳米管（CNTs）对Ti/Ru-Ir-Sn氧化物阳极的影响规律. 热重分析和阳极能谱数据表明,在烧结温度470 ^oC条件下CNTs未发生高温氧化分解,仍以单质形式存在阳极涂层中. 与对比样品相比,涂层表面裂纹增多,但仍保持典型形貌. 添加CNTs显著改善了Ti/Ru-Ir-Sn氧化物阳极的电化学性能,增大了阳极的活性表面积,减小了涂层内部电阻,提高了阳极析氯电催化活性,析氯电位增加缓慢,阳极强化电解寿命也得到明显延长. 其中,添加0.1 g·L^-1 CNTs的Ti/Ru-Ir-Sn氧化物阳极电催化活性和稳定性最优.     

Phosphorus‐containing polyamide Mg(OH)2 nanocomposite coating on surface of poly(vinyl chloride) thin film: Study on thermal stability,flammability, and mechanical properties

Surface of poly(vinyl chloride) (PVC) thin films was coated using DOPO‐based polyamide (DBPA) coating and DBPA/Mg(OH)₂ nanocomposites (DBPN) coating by dip‐coating process. For this purpose, a new DOPO‐based dicarboxylic acid (DBDA) was synthesized and used for preparation of DBPA and organically surface modification of Mg(OH)₂ nanoparticles. The effects of DBPA and DBPN coatings on the morphology, thermal stability, combustion, and mechanical properties of PVC were investigated. The uniform dispersion of Mg(OH)₂ nanoparticles (nano‐MDH) and organically coating manner on the surface of the PVC films were confirmed by ATR‐IR spectroscopy, X‐ray diffraction (XRD), field emission scanning electron microscopy (FE‐SEM), energy dispersive X‐ray, and elemental mapping. From thermal gravimetry analysis (TGA) results, the 10 mass% loss temperature (T₁₀) increased from 268°C to 272°C in PVC coated with DBPA‐containing 10 mass% of modified Mg(OH)₂ (MMH). Also the char residue, first and second mass loss temperatures of all PVC coated were increased compared with the neat PVC film. According to microscale combustion calorimetry (MCC) results, the peak of heat release rate (pHHR) and total heat release (THR) were decreased from 128 ± 2 to 69 W/g and 12 ± 1 to 4 ± 2 KJ/g for PVC film coated with DBPA‐containing 10 mass% of MMH, compared with the neat PVC. From tensile test results, tensile strength was increased from 31.78 ± 0.8 to 39.64 ± 0.9 MPa for PVC coated with polyamide‐containing 5 mass% of MMH compared with the neat PVC.