胶粒为“Salami”结构的PMMA/SiPUA乳液与膜性能研究

采用两步法,先以六亚甲基二异氰酸酯(HDI)、聚醚二元醇(N210)、端羟丙基硅油(HPMS)、端羟基丙烯酸树脂(PA-OH)为主要原料,合成了含硅聚氨酯-丙烯酸酯(Si PUA)种子乳液,然后在Si PUA乳胶粒内引入甲基丙烯酸甲酯(MMA),通过原位自由基共聚合,构筑了以Si PUA为壳,聚甲基丙烯酸甲酯(PMMA)为多核的"Salami"结构乳胶粒(PMMA/Si PUA).FTIR和DSC测试表明,聚氨酯、有机硅与丙烯酸酯发生反应,并确认了PMMA的生成;TEM结果显示,PMMA/Si PUA乳胶粒子具有"Salami"结构;随着Si PUA中HPMS含量的增加,PMMA/Si PUA乳胶粒子的粒径先增加后减小,粒径分布则从单峰窄分布变化到双峰宽分布,其乳液涂膜的水接触角呈现先增加后减小的趋势,但膜的吸水率则逐渐减小;与Si PUA相比,PMMA/Si PUA涂膜的透明性有一定下降,相分离程度增加;动态流变测试显示,PMMA/Si PUA涂膜中PMMA的存在,提高了其模量和黏度.当Si PUA中HPMS含量为10 wt%,核/壳质量比m(PMMA)/m(Si PUA)=0.5时,PMMA/Si PUA乳液的粒径较小,且为单峰分布,其涂膜的耐水性和耐高温性能较好.     

新型海参硫酸软骨素葡萄糖受体及葡萄糖醛酸受体的高效合成

以D-葡萄糖为起始原料,经9步反应合成了2-O-苄基-3-O-烯丙基-1-O-对甲氧基苯基α-D-葡萄糖(9);将9的6-位伯羟基经叔丁基二苯基硅烷基(TBDPS)保护,首次合成了正交保护的新型葡萄糖受体2-O-苄基-3-O-烯丙基6-O-叔丁基二苯基硅烷基1-O-对甲氧基苯基α-D-葡萄糖(Ⅱ),总收率28.2%;将9的6-位伯羟基氧化糖醛酸化后,再经甲酯化,以25.0%的总收率首次合成了新型葡萄糖醛酸受体2-O-苄基-3-O-烯丙基-1-O-对甲氧基苯基α-D-葡萄糖醛酸甲酯(Ⅲ),化合物结构经¹H NMR,¹³C NMR, IR和HR-MS(ESI)表征。     

HTEMPO和TMPD调控下MMA可控/活性光聚合研究

以HTEMPO(2,2,6,6-四甲基-4-羟基哌啶-1-氧自由基)和TMPD(2,2,6,6-四甲基哌啶酮)为调控介质, 以Irgacure 651为引发剂, 研究了甲基丙烯酸甲酯(MMA)光聚合体系的控制反应动力学, 比较了单分子(HTEMPO为调控介质)和双分子(HTEMPO和TMPD为调控介质)调控体系, 并讨论了HTEMPO和HTEMPO/TMPD在MMA光聚合体系中的调控作用、 光敏化作用和原位光氧化反应. 结果表明, 对MMA光聚合体系, 以HTEMPO/TMPD为控制介质的双分子调控体系是有效的, 获得了良好的ln(\[M0\]/\[M\])与时间, 数均分子量与转化率之间的线性动力学关系, 并且PMMA均聚物的多分散性指数(PDI)随着转化率的提高而减小. 在高转化率(>85%)下, 体系的多分散性指数(PDI)最小值可达到1.2.     

甲基丙烯酸甲酯的可控/“活性”细乳液光聚合

在室温下, 以2,2,6,6-四甲基-4-羟基哌啶-1-氧自由基(HTEMPO)为调控介质, 1-羟基-环己基-苯基甲酮(Irgacure 184)为引发剂, 采用光化学方法研究了甲基丙烯酸甲酯(MMA)/十二烷基硫酸钠(SDS)/十六醇(CA)/水细乳液体系的光聚合反应控制动力学. 结果表明, 该细乳液体系非常稳定, 在整个聚合过程中即没有絮凝物产生, 也没有沉淀析出, 获得了良好的ln([M0]/[M])与时间、数均分子量与转化率之间的线性动力学关系, 并且在整个聚合反应过程中MMA均聚物的分子量分布比较窄, 其多分散性指数较低(PDI=1.27~1.36), 具有明显的活性聚合特征.     

聚合物共混物的超高效液相色谱-空间排阻色谱在线联用分离与表征

黏合剂和涂料行业中, 聚合物共混物表征是分析的难题, 分离技术的研究一直备受关注. 本文设计并搭建了超高效液相色谱-空间排阻色谱在线联用系统(UHPLC-SEC), 采用羟基聚丁二烯(HTPB)考察了二维色谱系统的溶剂兼容性及正交性, 以苯乙烯-丁二烯嵌段共聚物(SBS)、 苯乙烯-异戊二烯嵌段共聚物(SIS)和聚甲基丙烯酸酯(PMMA)共混物研究了二维色谱系统的适用性. 结果表明, HTPB分子量及分布的UHPLC-SEC测定结果与SEC测定结果一致, 峰尖分子量(M_p)为3407 Da, 重均分子量(M_w)为6573 Da, 分散系数(PDI)为2.36, 相对标准偏差(RSD)均小于5.7%, 系统的溶剂兼容性和正交性良好. UHPLC-SEC法测得聚合物共混物中PMMA, SBS和SIS的M_p, M_w和PDI与单个聚合物的SEC测定结果的相对误差均小于7.1%. PMMA, SBS和SIS共混物在200 °C加热3 h后, PMMA 稳定不变, SBS和SIS组分明显降解. UHPLC-SEC在线联用方法对聚合物共混物的表征结果准确、 重复性好, 为聚合物配方产品的失效分析提供了一种重要且有效的手段.     

反胶束模板制备聚甲基丙烯酸甲酯/无机纳米粒子/石墨纳米复合材料及其表征

以甲基丙烯酸甲酯(MMA)和三氯甲烷(CHCl₃)为油相制备反胶束微乳液, 依靠表面活性剂十六烷基三甲基溴化铵(CTAB)自组装形成的“微反应器”作为模板成功地制备了PMMA/Eu(OH)₃/EG和PMMA/Ni(OH)₂/EG纳米复合材料. 并用红外光谱(IR)、扫描电镜(SEM)、透射电镜(TEM)、X射线衍射(XRD)和差热-热重(TG-DTA)对该复合材料进行了表征和分析. 研究结果表明, 反胶束法可以有效地应用于有机-无机纳米复合材料的制备.     

三氟甲基取代叔丁基亚磺酰亚胺的不对称aza-Morita-Baylis-Hillman反应

三氟甲基取代的N-叔丁基亚磺酰亚胺和α, β-不饱和羰基化合物在三乙烯二胺(DABCO)和Ti(OⁱPr)₄共催化下反应，实现了底物诱导的不对称aza- Morita-Baylis-Hillman反应，以高产率(49%~97 %)，高非对映选择性(dr>99/1)合成了一系列N-叔丁基亚磺酰基-α-甲亚基-β-三氟甲基-β-氨基酸酯产物。该产物经脱保护、关环可进一步转化为光学纯的α-甲亚基-β-三氟甲基-β-内酰胺类化合物，产物结构经¹H NMR、 ¹³C NMR和HR-MS确证。      

微波聚合制备单分散、超细聚甲基丙烯酸甲酯微球

在微波辐照下,通过甲基丙烯酸甲酯(MMA)的无乳化剂乳液聚合,制备出粒径单分散、超细聚甲基丙烯酸甲酯(PMMA)微球。微波显著缩短聚合诱导期,加快聚合反应,其部分原因是微波加快引发剂过硫酸钾(KPS)的分解。实验证明微波辐照下KPS的表观分解活化能(ED)由128.3kJ/mol降低到106.0kJ/mol。单体浓度是影响PMMA乳液粒子尺寸的主要因素,在[MMA]小于0.3mol/L时,平均粒径随单体浓度提高而线形增加;[MMA]为0.3～1.0mol/L时,平均粒径稳定在约200nm;之后随单体浓度进一步增加,乳液稳定性变差。引发剂浓度增加对平均粒径影响较小,但增大引发剂浓度可显著降低粒径分散度。选取[MMA]为0.23～0.3mol/L、[KPS]为3×10-3～6×10-3mol/L可以得到粒径200nm的单分散微球。以丙酮/水(体积比1/3)为反应介质,可制备出数均粒径45nm的PMMA纳米粒子。在体系中加入3.5×10-3mol/L的Cu2+,可制备出数均粒径67nm、单分散的PMMA纳米粒子。     

当归多糖ASP3及其水解产物的NMR光谱分析

对当归多糖ASP3的糖链结构进行分析. 分别采用0.2 mol/L三氟乙酸(Trifluoroacetic acid, TFA)和内切-α-(1→4)-聚半乳糖醛酸酶(EndoPG)对ASP3进行部分酸水解和酶水解, 并对水解前后多糖组分的1D和2D NMR光谱特征进行分析. 实验结果表明, ASP3是一种果胶多糖. GalpA和Rhap位于多糖分子的主链, 由1→4-D-GalpA相连形成的“光滑区”(半乳糖醛酸聚糖)是其主要组成部分; 由α-(1→4)-GalpA通过O4位与α-(1→2)-和α-(1→2,4)-Rhap的O2位交替连接所形成的重复单元[→4)-α-GalpA-(1→2)-α-Rhap-(1→]构成具有较高分支的“毛发区”(富含中性糖侧链的鼠李半乳糖醛酸聚糖). Galp和Araf是中性糖侧链的主要组成, 通过Rhap残基的O4位与主链相连. 非还原性末端T-β-Galp, β-(1→3)-, β-(1→3,6)-, β-(1→4)-, β-(1→4,6)-Galp聚合形成以β-(1→3,6)-Galp为分支点的β-(1→6)-半乳聚糖和以β-(1→4,6)-Galp为分支点的β-(1→4)-半乳聚糖. T-α-Araf, α-(1→5)-Araf和α-(1→3,5)-Araf聚合形成以α-(1→3,5)-Araf为分支点的α-(1→5)-阿拉伯聚糖. 此外, 由α-(1→5)-阿拉伯聚糖通过α-(1→3)连接与β-(1→6)-半乳聚糖末端聚合形成阿拉伯半乳聚糖.     

亚微米级聚苯乙烯/聚硅氧烷核壳粒子的制备及其应用

以乳液聚合制备的聚苯乙烯乳液为种子,加入甲基三甲氧基硅烷(MTMS)水解溶液进行缩聚反应,合成亚微米级聚苯乙烯/聚硅氧烷核壳粒子,并以此作为光散射剂添加至聚甲基丙烯酸甲酯(PMMA)树脂中,制备了光散射材料;考察了亚微米级核壳粒子添加在PMMA树脂中的分散性。结果表明:经过双螺杆剪切作用的挤出加工后,可以实现核壳粒子在PMMA树脂中的良好分散。核壳粒子可以大幅度提高PMMA的雾度,当聚苯乙烯/聚硅氧烷核壳粒子(NS82)的含量为1%时,制得的PMMA样片(厚度为2 mm)的雾度为89%,透光率为69%,有效光散射系数为61%。     

Synthesis of core/shell structure of glycidyl–functionalized poly(methyl methacrylate) latex nanoparticles via differential microemulsion polymerization

The differential microemulsion polymerization technique was used to synthesize the nanoparticles of glycidyl-functionalized poly(methyl methacrylate) or PMMA via a two-step process, by which the amount of sodium dodecyl sulfate (SDS) surfactant required was 1/217 of the monomer amount by weight and the surfactant/water ratio could be as low as 1/600. These surfactant levels are extremely low in comparison with those used in a conventional microemulsion polymerization system. The glycidyl-functionalized PMMA nanoparticles are composed of nanosized cores of high molecular weight PMMA and nano-thin shells of the random copolymer poly[(methyl methacrylate)-ran-(glycidyl methacrylate)]. The particle sizes were about 50 nm. The ratios of the glycidyl methacrylate in the glycidyl-functionalized PMMA were achieved at about 5–26 wt.%, depending on the reaction conditions. The molecular weight of glycidyl-functionalized PMMA was in the range of about 1 × 10⁶ to 3 × 10⁶ g mol⁻¹. The solid content of glycidyl-functionalized PMMA increased when the amount of added glycidyl methacrylate was increased. The glycidyl-functionalized polymer on the surface of nano-seed PMMA nanoparticles was a random copolymer which was confirmed by ¹H-NMR spectroscopy. The amounts of functionalization were investigated by the titration of the glycidyl functional group. The structure of the glycidyl-functionalized PMMA nanoparticles was investigated by means of TEM. The glycidyl-functionalized PMMA has two regions of T_g which are at around 90 °C and 125 °C, respectively, of which the first one was attributed to the poly[(methyl methacrylate)-ran-(glycidyl methacrylate)] and the second one was due to the PMMA. A core/shell structure of the glycidyl-functionalized PMMA latex nanoparticles was observed.     

通过自由基反应合成聚甲基丙烯酸甲酯大分子单体

大分子单体是一类具有聚合反应活性的聚合物,分子量在几千到数万不等,聚合反应活性点一般是大分子的端基,聚苯乙烯大分子单体是此类化合物的一种［１,２］．若改变聚合物化学结构（ａ）,可制成具有不同性能的大分子单体;若改变端基（ｂ）,则可使大分子单体具有不同...     

利用反向原子转移自由基聚合反应合成聚甲基丙烯酸缩水甘油酯

以偶氮二异丁腈为引发剂,CuBr2/bpy为催化体系,甲基丙烯酸缩水甘油酯(GMA)通过反向原子转移自由基聚合反应合成了聚甲基丙烯酸缩水甘油酯(PGMA),其结构经1H NMR,IR和GPC确证。聚合反应符合活性自由基聚合特征,在聚合过程中GMA转化率和PGMA分子量随反应时间的延长而增大,分子量分布较窄。     

ANIONIC POLYMERIZATION OF ALKYL METHACRYLATES INITIATED BY nBuCu(NCy2)Li

Anionic polymerization of methyl methacrylate(MMA),n-butyl methacrylate(nBMA)and glycidyl methacrylate (GMA)initiated by nBuCu(NCy_2)Li(1)in tetrahydrofuran(THF)at-50℃to-10℃was investigated.It was found that the polymerization of MMA and nBMA initiated by 1 proceeded quantitatively in THF to afford PMMA and PBMA with polydispersity index 1.15-1.30 and nearly 100%initiator efficiencies at-10℃.The molecular weights increased linearly with the ratio of[monomer]/[1].However,a post-polymerization experiment c...     

Synthesis of well‐defined cyclodextrin‐core star polymers

The synthesis of 21‐arm methyl methacrylate (MMA) and styrene star polymers is reported. The copper (I)‐mediated living radical polymerization of MMA was carried out with a cyclodextrin‐core‐based initiator with 21 independent discrete initiation sites: heptakis[2,3,6‐tri‐O‐(2‐bromo‐2‐methylpropionyl]‐β‐cyclodextrin. Living polymerization occurred, providing well‐defined 21‐arm star polymers with predicted molecular weights calculated from the initiator concentration and the consumed monomer as well as low polydispersities [e.g., poly(methyl methacrylate) (PMMA), number‐average molecular weight (M_n) = 55,700, polydispersity index (PDI) = 1.07; M_n = 118,000, PDI = 1.06; polystyrene, M_n = 37,100, PDI = 1.15]. Functional methacrylate monomers containing poly(ethylene glycol), a glucose residue, and a tert‐amine group in the side chain were also polymerized in a similar fashion, leading to hydrophilic star polymers, again with good control over the molecular weight and polydispersity (M_n = 15,000, PDI = 1.03; M_n = 36,500, PDI = 1.14; and M_n = 139,000, PDI = 1.09, respectively). When styrene was used as the monomer, it was difficult to obtain well‐defined polystyrene stars at high molecular weights. This was due to the increased occurrence of side reactions such as star–star coupling and thermal (spontaneous) polymerization; however, low‐polydispersity polymers were achieved at relatively low conversions. Furthermore, a star block copolymer consisting of PMMA and poly(butyl methacrylate) was successfully synthesized with a star PMMA as a macroinitiator (M_n = 104,000, PDI = 1.05). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2206–2214, 2001     

New σ-μ ligands for the anionic polymerization of methacrylates in apolar medium

Poly(methyl methacrylate) (PMMA) has been anionically synthesized at high temperature and in apolar media, using diphenylhexyllithium (DPHLi) as initiator and a novel σ-μ chelating ligand to curb the side reactions. It has been indeed found that lithium 2-(dimethylamino-)ethoxide is a very efficient σ-μ ligand that prevents the anionic polymerization of methyl methacrylate (MMA) from being disrupted by significant secondary termination reactions. Ligand/initiator molar ratio, solvent polarity, temperature, monomer and active center concentrations are proved to be key parameters in the control of the polymerization process.     

Synthesis of cardanol-based photo-active SET-LRP initiator and its application to preparation of UV-cured resin

A benzophenone-containing SET-LRP initiator based on renewable and abundant cardanol was synthesised in 71 % yield using the selective etherification reaction. Next, methyl methacrylate (MMA) as a monomer was polymerised under SET-LRP conditions using the newly prepared initiator to prepare cardanol-end poly(methyl methacrylate) (PMMA). The kinetic results of the polymerisation indicated that the reaction was controllable when the monomer conversion was lower than approximately 50 %, and the molecular masses of PMMA measured by GPC were higher than the theoretical values while the monomer conversion was more than 50 %. In addition, most of the carbon-carbon double bonds of the side hydrocarbon chain of the end-cardanol group in the PMMA were kept intact from ¹H NMR spectrum characterisation. Accordingly, when the cardanol-end PMMA together with a tertiary amine-containing cardanol derivative was irradiated by UV light, the corresponding UV-cured resin was obtained. The chemical resistance and hardness of the UV-cured film were enhanced with the increasing irradiation time.     

Synthesis and characteristics of snowman-like fluorescent PMMA microbeads

This paper reports the fabrication of fluorescent snowman-like poly(methyl methacrylate) (PMMA) colloidal microbeads using a two-step method. The fluorescent cross-linked PMMA seeds were first synthesized by dispersion polymerization and then swelled in a monomer solution containing the methyl methacrylate monomer, a secondary cross-linker and initiator, followed by heat-induced polymerization. Scanning electron microscopy, confocal laser scanning microscopy, and Fourier transform infrared spectroscopy confirmed the synthesis of fluorescent snowman-like particles.     

Synthesis of block copolymer-stabilized Au-Ag alloy nanoparticles and fabrication of poly(methyl methacrylate)/Au-Ag nanocomposite film

[Poly(2-(N,N-dimethylamino)ethyl methacrylate)]-b-poly(methyl methacrylate)-b-[poly(2-(N,N-dimethylamino)ethyl methacrylate)] (M(n)=45,000; 20K-5K-20K; PDI = 1.2) block copolymer surfactant stabilized amphiphilic gold-silver alloy nanoparticles (Au-Ag(PDMA-b-PMMA-b-PDMA)) has been synthesized in both water and in organic medium. The block copolymer stabilized pre-made alloy nanoparticles were successfully dispersed in hydrophobic poly(methyl methacrylate) homopolymer matrix (PMMA) of molecular weight 30,000. The successful synthesis of alloy nanoparticles was accessed by Transmission Electron Microscope (TEM), Energy Dispersed X-ray (EDX), and UV-visible spectrophotometric analysis. The surface functionality of the nanoparticles was confirmed by quantitative determining the grafting density of polymer chain around the nanoparticle surface using combination of thermo gravimetric (TGA) and TEM analysis. The hydrodynamic diameter of the alloy particles including the polymer chains was obtained from dynamic light scattering measurement (DLS). The mechanism of synthesis of high concentration of Au-Ag alloy particles from HAuCl(4) and AgNO(3) (in presence of Cl(-) from reduction of gold salt) metal particles precursors and the successful preparation of poly(methyl methacrylate)/gold-silver nanocomposite films have been discussed.     

Redox Polymerization of Methyl Methacrylate in the Fluorous Triphasic System

Fluorous-phase chemistry is currently a topic of considerable interest1-6. Since fluoroustriphasic reactions were first described by the Curran and co-workers7, this triphasicsystem has been widely used for detagging7,8 and phase-vanishing reactions9-11. …