Absolute determination method for trace quantities of enantiomer of glufosinate by gamma-cyclodextrin modified capillary zone electrophoresis combined with solid-phase extraction and on-capillary concentration.

A highly sensitive and accurate determination method for trace quantities of enantiomers of glufosinate (D,L-GLUF), a phosphorus-containing amino acid-type herbicide, has been studied. The present method is based on the change in the mole ratio of the enantiomeric isomers after spiking of a known amount of an isomer (L-GLUF). The chiral separation and detection were made by gamma-cyclodextrin modified capillary zone electrophoresis (gamma-CD-CZE) with fluorescence detection. Solid-phase extraction of D,L-GLUF with titania was investigated as the pre-separation method to eliminate coexisting materials such as inorganic salts and organic compounds in river water. A separated D,L-GLUF was labeled with dansyl chloride and subjected to the on-capillary concentration using large-volume sample stacking (LVSS) before gamma-CD-CZE. The detection limit of the present method was as low as 2.0 x 10(-9) M. The present method was successfully applied to a model sample containing 2.0 x 10(-7) M D,L-GLUF in river water. It was confirmed that trace quantities of D-and L-GLUF in environmental samples can be accurately determined without any calibration curves and comparison standards.     

高效液相色谱-圆二色检测法分析甲霜灵的对映体纯度

以手性农药甲霜灵为研究对象,使用非手性高效液相色谱在不拆分对映体的条件下,利用圆二色检测器所测的各向异性系数(g)测定手性对映体纯度。实验结果表明,g与对映体过剩率(ee)具有良好的线性关系;通过比较g所测ee与手性色谱所测的ee,二者所测ee相对平均偏差小于3.0%,说明该方法具有较高的准确性,可应用于手性化合物对映体纯度的测定。     

Validation of a method using an achiral liquid chromatography sorbent and a circular dichroism detector. Analysis of the efaroxan enantiomers

The known HPLC method using an achiral C8 silica sorbent and a circular dichroism (CD) detector for the determination of efaroxan enantiomeric excess has been validated. After optimization of the mobile phase, the enantiomers were detected at 278 nm offering maximum ellipticity between two optically active forms. The calibration curve of the anisotropy factor (g) versus the enantiomeric excess was linear with a correlation coefficient (r2) of 0.9985. The accuracy of the method was assessed by comparing the enantiomeric excess obtained by measuring the g factor (C8 column, CD and UV detections) with those determined by enantioselective HPLC (Chiralpak AD-H column, UV detection). Statistical tests (level of confidence of 95%) were assessed to compare the two orthogonal methods. The straight line gave a correlation coefficient of 0.9995, an intercept not significantly different from zero (0.0549) and a slope of 1.026. The precision evaluated on retention time (RSD<0.6%), g factor (RSD<8.3%) and CD peak area (RSD<7.5%) was suitable both in term of intra- and inter-day precisions. The proposed method has the advantages of being fast and precise without using expensive chiral column. Non-enantioselective HPLC-CD was suitable for the simultaneous determination of the optical and chemical purity of efaroxan.     

Quantification of very low enantiomeric impurity of efaroxan using a dual cyclodextrin system by capillary electrophoresis

A rapid method for the enantiomeric purity determination of efaroxan has been developed by capillary electrophoresis (CE) using a dual cyclodextrin (CD) system. The influence of the nature and the concentration of CDs on separation parameters has been studied. High resolution (R_s = 7) and peak efficiency (104 000-121 000 theoretical plates) values were obtained for efaroxan enantiomers by adding two cyclodextrins, one neutral (7.5 mM DM-β-CD) and the other negatively charged (3 mM CM-β-CD) to the running buffer composed of 100 mM phosphoric acid-triethanolamine (pH 3). These resolution and peak efficiencies values allowed the quantitation of the (S)-enantiomer of efaroxan at very low enantiomeric excess even if the minor component migrates after the major one. This method was fully validated for the enantiomeric impurity determination of the (S)-form of efaroxan at the 0.05% level. Calibration curve, expressed by the peak areas ratio versus the enantiomeric purity was linear over the 0.05-1% enantiomeric impurity range (r² = 0.9996). Limits of detection (LOD) and quantification (LOQ), expressed in term of (S)-enantiomer impurity were 0.02% and 0.05%, respectively. The accuracy of the method at 0.12%, 0.50% and 0.80% enantiomeric impurity levels for the (S)-form were determined. Recoveries were in 94-102% range for each quality control sample and were determined with good precision (intra-day R.S.D. = 3.54%, inter-day R.S.D. = 5.33%).     

Rapid coprecipitation-separation and flame atomic absorption spectrometric determination of lead and cadmium in water with cobalt (II) and ammonium pyrrolidine dithiocarbamate

A coprecipitation technique which does not require complete collection of the precipitate was proposed for the determination of trace lead and cadmium in water with flame atomic absorption spectrometry (FAAS) after preconcentration of lead and cadmium by using cobalt (II) and ammonium pyrrolidine dithiocarbamate (Co-APDC) as coprecipitant and known amount of cobalt as an internal standard. Since lead, cadmium and cobalt were well distributed in the homogeneous precipitate, the concentration ratio of lead to cobalt, and cadmium to cobalt remained unchanged in any part of the precipitate. The amount of lead and cadmium in the original sample solution can be calculated respectively from the ratio of the absorbance values of lead and cadmium to cobalt in the final sample solution that is measured by FAAS and the known amount of the lead and cadmium in the standard series solutions. The optimum pH range for quantitative coprecipitation of lead and cadmium is from 3.0 to 4.5. The 16 diverse ions tested gave no significant interferences in the lead and cadmium determination. Under optimised conditions, lead ranging from 0 to 40?µg and cadmium ranging from 0 to 8?µg were quantitatively coprecipitated with Co-APDC from 100?mL sample solution (pH?～?3.5). This coprecipitation technique coupled with FAAS was applied to the determination of lead and cadmium in water samples with satisfactory results (recoveries in the range of 94.0–108%, relative standard deviations <6.0%).     

A fluorimetric, column-switching HPLC and its application to an elimination study of LLU-alpha enantiomers in rat plasma

A method for the enantiomeric determination of 2,7,8-trimethyl-2-(beta-carboxyethyl)-6-hydroxy chroman (LLU-alpha, gamma-CEHC) in rat plasma was developed using high-performance liquid chromatography (HPLC) with a fluorimetric derivatization with 4-N, N-dimethylaminosulfonyl-7-piperazino-2,1,3-benzoxadiazole (DBD-PZ) followed by O-acetylation with acetyl chloride. The proposed HPLC system used two non-chiral columns (phenyl and octadecylsilica) and a chiral column (a modified cellulose type), which were connected via two column-switching valves. A derivatized sample prepared from rat plasma was first separated on the phenyl column, and the fraction including LLU-alpha derivative was introduced to the octadecylsilica column to quantify the concentration of the mixture of S- and R-LLU-alpha. Finally, the LLU-alpha derivative was directly injected into the chiral column to obtain the ratio of the enantiomers. The proposed HPLC system was applied to the enantiomeric determination of LLU-alpha in plasma after intravenous administration of racemic LLU-alpha. S-LLU-alpha was eliminated faster than R-LLU-alpha, and its concentration in plasma decreased to one-third at 2 min after dosing.     

Enantioselective analysis of methadone in saliva by liquid chromatography-mass spectrometry

Saliva was tested and evaluated as a biological matrix for methadone (Mtd) monitoring. Conventional method using a narrow bore C18 column, and an enantioselective method using a narrow bore alpha1-acid glycoprotein column, were developed using liquid chromatography coupled with a mass spectromeric (MS) detector. After optimisation of MS conditions by flow injection analysis, selected ion monitoring detection was used to enhance sensitivity. The total Mtd concentration and the enantiomeric ratio in saliva were validated using an experimental design. The methods were applied to samples provided by heroin addicts undergoing a Mtd treatment. Results on total Mtd determination showed a very poor correlation between saliva and serum, whereas the enantiomeric ratios of Mtd gave a very good one.     

Simultaneous determination of D-lactic acid and 3-hydroxybutyric acid in rat plasma using a column-switching HPLC with fluorescent derivatization with 4-nitro-7-piperazino-2,1,3-benzoxadiazole (NBD-PZ)

A highly sensitive method for the determination of D-lactic acid and 3-hydroxybutyric acid (3-HB) in rat plasma was developed using high-performance liquid chromatography with octadecylsilica (ODS) connected to a chiral column. At first, (D + L)-lactic acid and 3-HB in the plasma were derivatized with a fluorescent reagent, 4-nitro-7-piperazino-2,1,3-benzoxadiazole (NBD-PZ), separated on the ODS column and determined fluorimetrically at 547 nm with 491 nm of excitation wavelength. During the separation step on the ODS, the peak fraction of (D + L)-lactate derivative was introduced directly to a phenylcarbamoylated beta-cyclodextrin chiral column by changing the flow of the eluent via a six-port valve. Then, D-lactate derivative was separated enantiomerically from the L-lactate derivative, and the enantiomeric ratio was determined from the chromatogram. Intra- and inter-day accuracy values for the determination of D-lactic acid in 10 microL of rat plasma were 97.8-109.2 and 98.4-109.9%, and those for 3-HB were 99.8-108.4 and 99.8-103.8%, respectively. The intra- and inter-day precision values were within 4.6 and 5.1% for D-lactic acid, and 2.7 and 2.4% for 3-HB, respectively. The detection limits for D-lactic acid and 3-HB were approximately 2.0 and 0.04 microM, respectively (signal-to-noise ratio 3). The proposed method was applied to the plasma of diabetic rats induced by intraperitoneal administration of streptozotocin, and the significant increases of both D-lactic acid and 3-HB concentrations were observed in the diabetic rats as compared to the normal rats.     

交联淀粉囊材对含羧基类除草剂的缓释性能研究

以淀粉或变性淀粉为囊材,对囊化农药进行控释或缓释,可延长药效、避免药害、减少浪费和防止污染^[1-4]。 然而,水溶胀程度大导致淀粉胶囊制品耐水性差。目前,降低其水溶胀程度的措施有淀粉黄原酸酯化后的交联囊化法^[5]、淀粉－钙加合物法^[6]和淀粉－硼酸络合物法^[7,8]。但由于含羧基类农药的水溶性对碱敏感,上述方法中淀粉的糊化、化学改性和交联所必须的强碱性条件会使含羰基类农药呈现水溶性,致使它们在水环境条件下会以更大的速度从淀粉囊材中释放出来。可 见,含羧基类农药不能用这几种方法来改善其缓释性能。本文以甲醛为交联剂,在淀粉囊化农药过程中对淀粉囊材进行交联,能够有效地降低淀粉胶囊制品的水溶胀程度的和所囊药剂的释放速度,延长有效控释时间,较大幅度地提高其缓释性能和耐水性。该囊化方法解决了一些碱敏感性农药在淀粉中的囊化问题。     

手性镧系位移试剂核磁共振法测定芳氧丙酸酯类除草剂对映体纯度

以Eu(hfc)3和Pr(hfc)3为手性镧系位移试剂(CLSR),比较了两种CLSR对2,4-滴丙酸甲酯的1HNMR和13C NMR谱手性分离效果,结果表明:Pr(hfc)3比Eu(hfc)3对手性中心相连的甲基具有更好的手性分离效果。首次应用Pr(hfc)3测定了盖草能、稳杀得和喹禾灵3种手性芳氧丙酸酯类除草剂的1HNMR和13CNMR谱,其1HNMR谱分离度R约为1,盖草能和喹禾灵的13C NMR谱分离度R大于1.5,说明1H NMR和13CNMR谱手性分离效果适用于对映体纯度测定。与手性色谱法相比,CLSR-NMR法测定对映体纯度具有操作简便、分析速度快的显著优势。     

Determination of the deuterium/hydrogen ratio of endogenous urinary steroids for doping control purposes

The development and application of a combined gas chromatography/thermal conversion/isotope ratio mass spectrometry (GC/TC/IRMS) method for D/H ratio determination of endogenous urinary steroids are presented. The key element in sample preparation was the consecutive cleanup with high‐performance liquid chromatography of initially native and subsequently acetylated steroids. This strategy enabled sufficient cleanup off all target analytes for determination of their respective D/H values. Ten steroids (11β‐hydroxyandrosterone, 5α‐androst‐16‐en‐3α‐ol, pregnanediol, androsterone, etiocholanolone, testosterone, epitestosterone, 5α‐androstan‐3α,17β‐diol, 5β‐androstan‐3α,17β‐diol and dehydroepiandrosterone) were measured from a single urine specimen. Depending on the biological background, the determination limit for all steroids ranged from 10 to 15 ng/mL for a 20 mL specimen. The method was validated by application of linear mixing models on each steroid and covered repeatability and reproducibility. The specificity of the procedure was ensured by gas chromatography/mass spectrometry (GC/MS) analysis of the sample using equivalent chromatographic conditions to those employed in the GC/TC/IRMS measurement. Within the sample preparation, no isotopic fractionation was observed, and no amount‐dependent shift of the D/H ratios during the measurement was noticed. Possible memory effects occurring during IRMS measurements were corrected by applying a simple rule of proportion. In order to determine the naturally occurring D/H ratios of all implemented steroids, a population of 18 male subjects was analyzed. Relevant mean Δ values among selected steroids were calculated which allowed us to study the metabolic pathways and production sites of all the implemented steroids with additional consideration of the corresponding ¹³C/¹²C ratios. Copyright © 2009 John Wiley & Sons, Ltd.     

Sample stacking with matrix removal for the determination of paraquat, diquat and difenzoquat in water by capillary electrophoresis

Conditions for the simultaneous determination of paraquat, diquat and difenzoquat by capillary zone electrophoresis using a stacking technique in a chemically modified capillary have been established. To apply the stacking method with sample matrix removal for the analysis of cations, an anodic electroosmotic flow is mandatory. For quats, 50 mM acetic acid-ammonium acetate (pH 4.0) with 5% (v/v) methanol as electrophoretic buffer and the addition of 0.8 mM cetyltrimethylammonium bromide as wall capillary organic modifier was proposed. Field polarity reversal time was optimised for several sample matrices. Detection was carried out at 220 and 255 nm. Detection limits, based on a signal-to-noise ratio of 3:1, were lower than 15 microg l(-1) for standards in Milli-Q water and two to ten times higher for drinking water samples. Run-to-run and day-to-day reproducibility have been established. The method was successfully applied to the determination of the three herbicides in spiked drinking water.     

Enantiomeric and isomeric separation of herbicides using cyclodextrin-modified capillary zone electrophoresis

Cyclodextrin-modified capillary zone electrophoresis (CD-CZE) was applied successfully to the enantiomeric and isomeric separation of three herbicides (imazaquin, diclofop and imazamethabenz). Commercially available cyclodextrins were evaluated for separation of the enantiomers and isomers of the three herbicides having varied molecular structures. The enantiomers of imazaquin and diclofop, and the isomers of imazamethabenz could be resolved with a resolution of ≥1.5. The resolution was found to depend on pH of the run buffer, cyclodextrin type and cyclodextrin concentration. By employing mixed cyclodextrins in the running buffer, the three herbicides were simultaneously separated in a single run. In addition, rapid (less than 3 min) enantiomeric separation is demonstrated using imazaquin as a model herbicide. The reported capillary electrophoresis (CE) methods are simple, rapid, efficient and reproducible and our results demonstrate that CE provides a powerful analytical tool for enantiomeric and isomeric separation of herbicides.     

等离子体原子发射光谱法（ICP─AES）间接测定水样中的硫酸根

本文报导以Ｂａ２＋将样品溶液中的硫酸根（ＳＯ）以硫酸钡形式分离，用等离子体光谱法测定余量Ｂａ２＋，从而间接测得ＳＯ含量的方法。该法操作简便、快速、灵敏、准确，化学干扰和光谱干扰小，可准确测定低至０．２ｍｇ的硫酸根含量。方法适用于各种水样中硫酸根的测定，获得满意结果。     

Ionic‐liquid‐functionalized zinc oxide nanoparticles for the solid‐phase extraction of triazine herbicides in corn prior to high‐performance liquid chromatography analysis

Zinc oxide nanoparticles have recently been used as effective adsorbent materials for sample pretreatment in analytical chemistry because of their excellent properties, such as high specific surface area, high effective porosity, non‐toxicity, and ease of fabrication. In this study, the zinc oxide nanoparticles functionalized by an ionic liquid, 1‐carboxyethyl‐3‐methylimidazolium chloride, were fabricated and used as the adsorbent for the solid phase extraction of five triazine herbicides in corn for the first time. High‐performance liquid chromatography was employed for the determination of these triazine herbicides. Several experimental parameters affecting the extraction efficiency were investigated, including the volume of extraction solvent, the extraction time, the type of extraction solvent and elution solvent, the amount of absorbent, and the volume of elution solvent. By using the proposed method, low limits of detection and quantification for all the five triazine herbicides were obtained between 0.71–1.08 and 2.67–3.64 ng/g, respectively. Recoveries of the proposed method range from 89.05 to 100.33% with intra‐ and inter‐day relative standard deviations lower than 8.45%. The calibration curves are linear in the concentration range of 0.005–1.00 μg/g with the correlation coefficient higher than 0.9954.     

Determination of Triazine Herbicides and Metabolites by Solid Phase Extraction with HPLC Analysis

An efficient solid phase extractive preconcentration/separation method was developed for the trace determination of herbicides in aqueous samples using Amberlite XAD-4 resin as the adsorbent. The retained herbicides were eluted with methanol at a flow rate of 1.0 mL min^?1 and determined by HPLC-DAD (wavelength of 220 nm) using water (pH:4.7, phosphoric acid) and methanol (ratio 35:65) as the mobile phase with a flow rate of 1.0 mL min^?1. Quantitative recoveries of simazine, atrazine and its metabolities were achieved at optimized analysis conditions that included 0.75 g of resin; a pH of 3.0; an eluent volume of 3.0 mL; an eluent flow rate of 1.0 mL min^?1; and a sample flow rate of 4.0 mL min^?1. The limits of detection, preconcentration factor, and linear ranges for the herbicides were 0.084–0.121 µgL^?1, 1000, and 0.5–20 mg L^?1, respectively. The performance of the method was evaluated by analysis of spiked water samples. The recoveries of simazine, atrazine and their metabolities were found to be quantitative (99.6–104.8%) with RSDs of 2.2–4.8% and 2.8–4.7% for intra-day and inter-day precision, respectively. The proposed method was successfully applied for trace determination of studied analytes in waste water, apple juice, and red wine samples.     

Solid phase extraction and graphite furnace atomic absorption spectrometric determination of ultra trace amounts of bismuth in water samples

A simple and reliable method for the selective extraction and determination of bismuth in water as well as alloy samples using octadecyl bonded silica cartridge modified with cyanex 301 and graphite furnace atomic absorption spectrometry is described. Extraction efficiency and influence of sample matrix, optimum amount of extraction ligand, type and least amount of proper eluent and flow rates were evaluated. The limit of detection of the proposed method is 0.01 ng ml(-1). The influence of potential interfering cations in water samples on the recovery of bismuth was investigated. The method was successfully applied to the extraction and determination of bismuth in natural water and alloy samples.     

Optimized derivatization of acidic herbicides with trimethylsilyldiazomethane for GC analysis

In the present study, the preparation of methyl esters of chlorophenoxy acids with trimethylsilyldiazomethane (TMSD) is reported. TMSD is a mild and safe alternative to the highly toxic, thermally labile, and explosive diazomethane. Due to the novelty of this method, the characteristics of the reaction were investigated and the derivatization procedure was screened for statistically significant factors. The parameters identified as influential are the amount of methanol as well as reaction time and temperature. A careful optimization by a complete factorial response surface design was carried out to generate optimal reaction conditions with respect to maximum recovery and reaction yield. Special emphasis has been given to an accurate validation of the derivatization procedure. LODs were determined between 4.1 and 8.1 ng/mL for the enriched sample and linearity was proofed for more than five orders of magnitude. The applicability of the method was demonstrated by the analyses of quality control material including sample preparation with SPE. Polar herbicides investigated in the study belong to acetic acid (2,4-D, MCPA, and 2,4,5-T), butanoic acid (MCPB), and propanoic acid (mecoprop). An efficient, fast, and high-throughput method for the determination of polar herbicides including the potential for automation is proposed.     

Enantiomeric separation of FMOC-amino acids by nano-LC and CEC using a new chiral stationary phase, cellulose tris(3-chloro-4-methylphenylcarbamate)

A novel polysaccharide-based chiral stationary phase (CSP), cellulose tris(3-chloro-4-methylphenylcarbamate), also known as Sepapak-2 or Lux Cellulose-2, has been evaluated for the enantiomeric separation of FMOC derivatives of amino acids. After mobile-phase optimization in nano liquid chromatography (nano-LC) the column enabled the enantiomeric separation of 19 out of 23 amino acids tested, indicating the high chiral recognition power of this new CSP. Subsequently, a comparison of the driving force employed (pressure or voltage) was carried out comparing nano-LC and CEC under the same conditions. Better peak efficiencies and resolution were observed by using CEC experiments, which enabled the chiral discrimination of 20 out of 23 amino acids tested. Finally, in order to show the potential of this new CSP, the determination of the content and the enantiomeric purity of the non-protein amino acid citrulline in food supplements was performed. For that purpose, the method was optimized, evaluated and applied to different commercial samples.     

Solid-phase extraction and spectrophotometric determination of trace amounts of copper in water samples

A simple method for rapid and selective extraction, preconcentration and determination of copper as it's neocuproine complex by using octadecylsilica membrane disks and spectrophotometry is presented. Extraction efficiency and the influence of flow rates of sample solution and eluent, pH, amount of neocuproine and hydroxylamine hydrochloride, type and least amount of eluent for elution of copper complex from disks, break through volume and limit of detection were evaluated. Also the effects of various cationic interferences on percent recovery of copper were studied. Extraction efficiencies >99% were obtained by elution of the disks with minimal amount of solvent. The limit of detection of the proposed method is 0.12 ppb. The method was applied to the recovery and determination of copper in different water samples.