Effect of surface roughness and softness on water capillary adhesion in apolar media

The roughness and softness of interacting surfaces are both important parameters affecting the capillary condensation of water in apolar media, yet are poorly understood at present. We studied the water capillary adhesion between a cellulose surface and a silica colloidal probe in hexane by AFM force measurements. Nanomechanical measurements show that the Young's modulus of the cellulose layer in water is significantly less (~7 MPa) than in hexane (~7 GPa). In addition, the cellulose surface in both water and hexane is rather rough (6-10 nm) and the silica probe has a comparable roughness. The adhesion force between cellulose and silica in water-saturated hexane shows a time-dependent increase up to a waiting time of 200 s and is much (2 orders of magnitude) lower than that expected for a capillary bridge spanning the whole silica probe surface. This suggests the formation of one or more smaller bridges between asperities on both surfaces, which is confirmed by a theoretical analysis. The overall growth rate of the condensate cannot be explained from diffusion mediated capillary condensation alone; thin film flow due to the presence of a wetting layer of water at both the surfaces seems to be the dominant contribution. The logarithmic time dependence of the force can also be explained from the model of the formation of multiple capillary bridges with a distribution of activation times. Finally, the force-distance curves upon retraction show oscillations. Capillary condensation between an atomically smooth mica surface and the silica particle show less significant oscillations and the adhesion force is independent of waiting time. The oscillations in the force-distance curves between cellulose and silica may stem from multiple bridge formation between the asperities present on both surfaces. The softness of the cellulose surface can bring in additional complexities during retraction of the silica particle, also resulting in oscillations in the force-distance curves.     

Thickness and morphology of polyelectrolyte coatings on silica surfaces before and after protein exposure studied by atomic force microscopy

Analyte–wall interaction is a significant problem in capillary electrophoresis (CE) as it may compromise separation efficiencies and migration time repeatability. In CE, self-assembled polyelectrolyte multilayer films of Polybrene (PB) and dextran sulfate (DS) or poly(vinylsulfonic acid) (PVS) have been used to coat the capillary inner wall and thereby prevent analyte adsorption. In this study, atomic force microscopy (AFM) was employed to investigate the layer thickness and surface morphology of monolayer (PB), bilayer, (PB-DS and PB-PVS), and trilayer (PB-DS-PB and PB-PVS-PB) coatings on glass surfaces. AFM nanoshaving experiments providing height distributions demonstrated that the coating procedures led to average layer thicknesses between 1 nm (PB) and 5 nm (PB-DS-PB), suggesting the individual polyelectrolytes adhere flat on the silica surface. Investigation of the surface morphology of the different coatings by AFM revealed that the PB coating does not completely cover the silica surface, whereas full coverage was observed for the trilayer coatings. The DS-containing coatings appeared on average 1 nm thicker than the corresponding PVS-containing coatings, which could be attributed to the molecular structure of the anionic polymers applied. Upon exposure to the basic protein cytochrome c, AFM measurements showed an increase of the layer thickness for bare (3.1 nm) and PB-DS-coated (4.6 nm) silica, indicating substantial protein adsorption. In contrast, a very small or no increase of the layer thickness was observed for the PB and PB-DS-PB coatings, demonstrating their effectiveness against protein adsorption. The AFM results are consistent with earlier obtained CE data obtained for proteins using the same polyelectrolyte coatings.     

Transport mechanisms in capillary condensation of water at a single-asperity nanoscopic contact

Transport mechanisms involved in capillary condensation of water menisci in nanoscopic gaps between hydrophilic surfaces are investigated theoretically and experimentally by atomic force microscopy (AFM) measurements of capillary force. The measurements showed an instantaneous formation of a water meniscus by coalescence of the water layers adsorbed on the AFM tip and sample surfaces, followed by a time evolution of meniscus toward a stationary state corresponding to thermodynamic equilibrium. This dynamics of the water meniscus is indicated by time evolution of the meniscus force, which increases with the contact time toward its equilibrium value. Two water transport mechanisms competing in this meniscus dynamics are considered: (1) Knudsen diffusion and condensation of water molecules in the nanoscopic gap and (2) adsorption of water molecules on the surface region around the contact and flow of the surface water toward the meniscus. For the case of very hydrophilic surfaces, the dominant role of surface water transportation on the meniscus dynamics is supported by the results of the AFM measurements of capillary force of water menisci formed at sliding tip-sample contacts. These measurements revealed that fast movement of the contact impedes on the formation of menisci at thermodynamic equilibrium because the flow of the surface water is too slow to reach the moving meniscus.     

Water dynamics in silica nanopores: the self-intermediate scattering functions

The dynamics of water molecules confined in approximately cylindrical silica nanopores is investigated using molecular simulation. The model systems are pores of diameter varying between 20 and 40 ? containing water at room temperature and at full hydration, prepared using grand canonical Monte Carlo simulation. Water dynamics in these systems is studied via molecular dynamics simulation. The results of the basic characterization of these systems have been reported in A. A. Milischuk and B. M. Ladanyi [J. Chem. Phys. 135, 174709 (2011)]. The main focus of the present study is the self-intermediate scattering function (ISF), F(S)(Q, t), of water hydrogens, the observable in quasi-elastic neutron scattering experiments. We investigate how F(S)(Q, t) depends on the pore diameter, the direction and magnitude of the momentum transfer Q, and the proximity of water molecules to the silica surface. We also study the contributions to F(S)(Q, t) from rotational and translational motions of water molecules and the extent of rotation-translation coupling present in F(S)(Q, t). We find that F(S)(Q, t) depends strongly on the pore diameter and that this dependence is due mainly to the contributions to the ISF from water translational motion and can be attributed to the decreased mobility of water molecules near the silica surface. The relaxation rate depends on the direction of Q and is faster for Q in the axial than in the radial direction. As the magnitude of Q increases, this difference diminishes but does not disappear. We find that its source is mainly the anisotropy in translational diffusion at low Q and in molecular reorientation at higher Q values.     

Water sorption in hybrid silica gels containing colloidal nontronite

Hybrid silica gels (HSGs) were prepared according to an acid-catalyzed sol–gel method using tetraethoxysilane (TEOS) as silica precursors and colloidal suspension of nontronite clay mineral. The silica surfaces were hydrophilic in relation to silanol groups and it was of interest to increase hydrophobicity by substituting silanol by methylated groups through addition of methyltrimethoxysilane (MTMS) in a molar ratio TEOS: MTMS equaled to 1:0.4. The aim of the present paper was to predict effects of water content in soil on HSG hydration by characterizing HSG water desorption and sorption with dynamic vapor sorption device. From desorption kinetics, TEOS HSGs showed higher ability to water surface evaporation and diffusion compared to the TEOS–MTMS HSGs. After complete dehydration, water sorption isotherms Type II were obtained for HSGs. Isotherms were fitted with Brunauer-Emmett-Tellet (BET) and Guggenheim, Andersen, de Boer (GAB) models. The higher monolayer values of water adsorbed for HSGs containing nontronite suggested a major influence of clay minerals on overall hydration. However, the water binding energy depended upon the nature of silica matrix indicating weaker bonds with methylated groups at solid surface in MTMS–TEOS HSGs. Apparent water sorption diffusivities, D_app were calculated according to Fick’s diffusion model. Maximal D_app values were obtained in the range 0.2??.3 a_w after which the D_app decreased in relation with capillary condensation.     

Isoelectric point of fluorite by direct force measurements using atomic force microscopy

Interaction forces between a fluorite (CaF2) surface and colloidal silica were measured by atomic force microscopy (AFM) in 1 x 10(-3) M NaNO3 at different pH values. Forces between the silica colloid and fluorite flat were measured at a range of pH values above the isoelectric point (IEP) of silica so that the forces were mainly controlled by the fluorite surface charge. In this way, the IEP of the fluorite surface was deduced from AFM force curves at pH approximately 9.2. Experimental force versus separation distance curves were in good agreement with theoretical predictions based on long-range electrostatic interactions, allowing the potential of the fluorite surface to be estimated from the experimental force curves. AFM-deduced surface potentials were generally lower than the published zeta potentials obtained from electrokinetic methods for powdered samples. Differences in methodology, orientation of the fluorite, surface carbonation, and equilibration time all could have contributed to this difference.     

Layer-by-layer assembly of mucin and chitosan--Influence of surface properties, concentration and type of mucin

Bovine submaxillary mucin (BSM) and chitosan were used to build layer-by-layer structures on solid substrates. The build-up was monitored using in situ ellipsometry to obtain time resolved values of the thickness and adsorbed amount. Additionally surface morphology during build-up was studied by atomic force microscopy (AFM). It was found that the adsorbed amount of the film increases approximately linearly with each deposition cycle on hydrophobized silica whereas construction on silica was found not to be possible at the experimental conditions used. We conclude that sufficient amount of the first mucin layer is crucial for the subsequent multilayer formation. The complex build-up kinetics on hydrophobized silica is characterized by adsorption and redissolution processes and the overall growth is the sum of both processes. AFM imaging on hydrophobized silica also confirmed the presence of redissolution processes and chitosan addition led to a reduction both in the number of surface aggregates and in the roughness of the surface. The present work also shows that by adjusting the relative concentrations of the polyelectrolytes it is possible to change the growth rate considerably. The final structures after deposition of 8 bilayers were found to have a high content of water and film stability test revealed that a substantial amount dissolves when increasing electrolyte concentration or pH of the ambient solution. Human mucin from saliva (MUC5B) was also used to create multilayers with chitosan on hydrophobized silica and it was revealed that no redissolution appears to be present in this system.     

Particle-surface capillary forces with disjoining pressure

A new, atomic force microscopy (AFM) based experimental setup for the continuous acquisition of friction force data as a function of humidity has been developed. The current model of interactions between wet contacts under the influence of capillary effects, has been amended to include a vertical component due to the disjoining pressure and takes into account the influence of liquid films adsorbed on the surface. This is a 'switching' model, i.e. the contact between nanometer-sized sphere and a flat surface can exist in two distinct states due to capillary bridge formation/destruction as the humidity is varied. The model has been qualitatively verified on samples of differing wettability produced by UV-ozone treatment of polystyrene (PS). Results of AFM analysis of the friction vs. vapor pressure curves collected from the surface are presented. Correlation between important surface properties such as wettability, adsorption, and contact angle and friction force under varying humidity were found and discussed.     

Capillary forces: influence of roughness and heterogeneity

A formalism is described to calculate capillary forces between solid surfaces analytically. Assumptions are that the liquid menisci (1) have a much larger extension parallel to the gap than normal and (2) are formed by capillary condensation and are in equilibrium with the vapor. To calculate capillary forces, first the gap between the two surfaces is described by a height distribution function. Roughness is considered with an asperity distribution function. Both distributions can at least in principal be measured by light, electron, or atomic force microscopy or grazing incidence X-ray reflectivity. The total capillary force versus distance or vapor pressure is obtained by a convolution of both distributions and an integration. The formalism is applied to calculate the capillary force between rough spherical particles. In addition, a method to consider surface heterogeneity is suggested.     

Evanescent wave cavity ring-down spectroscopy (EW-CRDS) as a probe of macromolecule adsorption kinetics at functionalized interfaces

Evanescent wave cavity ring-down spectroscopy (EW-CRDS) has been employed to study the interfacial adsorption kinetics of coumarin-tagged macromolecules onto a range of functionalized planar surfaces. Such studies are valuable in designing polymers for complex systems where the degree of interaction between the polymer and surface needs to be tailored. Three tagged synthetic polymers with different functionalities are examined: poly(acrylic acid) (PAA), poly(3-sulfopropyl methacrylate, potassium salt) (PSPMA), and a mannose-modified glycopolymer. Adsorption transients at the silica/water interface are found to be characteristic for each polymer, and kinetics are deduced from the initial rates. The chemistry of the adsorption interfaces has been varied by, first, manipulation of silica surface chemistry via the bulk pH, followed by surfaces modified by poly(L-glutamic acid) (PGA) and cellulose, giving five chemically different surfaces. Complementary atomic force microscopy (AFM) imaging has been used for additional surface characterization of adsorbed layers and functionalized interfaces to allow adsorption rates to be interpreted more fully. Adsorption rates for PSPMA and the glycopolymer are seen to be highly surface sensitive, with significantly higher rates on cellulose-modified surfaces, whereas PAA shows a much smaller rate dependence on the nature of the adsorption surface.     

Forces between a Rigid Probe Particle and a Liquid Interface

The effect of disjoining pressure between a rigid spherical probe particle (attached to an AFM cantilever) and a liquid interface (e.g., oil/water or air/water) is treated in an analytic manner to describe the total force F exerted on the probe as a function of the distance X of the probe from the rigid substrate (AFM stage) on which the liquid interface resides. Two cases (i) a flat interface under gravity and (ii) a drop whose size is sufficiently small that gravity can be neglected have been examined. A simple numerical algorithm is given for computing F(X) (the AFM observable) from a given form for the disjoining pressure. Numerical results are displayed for electrostatic probe/interface interactions which reveal the linear compliance regime experimentally observed in AFM experiments on these systems. The slope of the linear compliance regime is shown to be a function of the properties of the interface (capillary length, particle radius, drop size, contact angle of drop on rigid substrate etc.). Copyright 2001 Academic Press.     

Volume of a nanoscale water bridge

Water bridges formed through capillary condensation at nanoscale contacts first stretch and then break during contact rupture. Atomic force microscopy (AFM) pull-off experiments performed in air with hydrophilic tips and samples show that stretched nanoscopic water bridges are in mechanical equilibrium with the external pull-off force acting at the contact but not in thermodynamic equilibrium with the water vapor in air. The experimental findings are explained by a theoretical model that considers constant water volume and decrease of water meniscus curvature during meniscus stretching. The model predicts that the water bridge breakup distance will be roughly equal to the cubic root of the water bridge volume. A thermodynamic instability was noticed for large water bridges formed at the contact of a blunt AFM tip (curvature radius of 400 nm) with a flat sample. In this case, experiments showed rise and stabilization of the volume of the water at the contact in about 1 s. For sharp AFM tips (curvature radius below 50 nm), the experiments indicated that formation of stable water bridges occurs in a much shorter time (below 5 ms).     

Water distribution in multilayers of weak polyelectrolytes

The water localization in thin polyelectrolyte multilayers assembled from poly(acrylic acid) and poly(allylamine hydrochloride) was investigated with neutron reflectivity in an atmosphere of controlled humidity and with bulk water. Water was found to be distributed asymmetrically within the multilayer and to localize preferentially at the polymer surface. The diffusion of water into the multilayer did not completely penetrate to the substrate, but instead there appeared to be an exclusion zone near the Si substrate. These results help to explain previous observations of anomalous water transport kinetics in weak polyelectrolyte systems.     

Diffusion of condensable vapors in single adsorbent particles measured via concentration-swing frequency response

A concentration-swing frequency response method is extended to examine mass transfer mechanisms and the concentration dependence of mass transfer rates for adsorption of condensable vapors in single adsorbent particles. The adsorption kinetics of water and hexane in BPL activated carbon and the adsorption of water in silica gel are determined at several different concentrations. The mechanism that best describes the adsorption of water in BPL activated carbon is nanopore diffusion. The diffusivity of water in BPL activated carbon has a clear minimum at approximately P/Po = 0.5, and the concentration dependence of the diffusion data are not described well by the Darken relationship. Both nanopore diffusion and the Glueckauf linear driving force models can be used to describe the diffusion of hexane in BPL activated carbon for the pressure range studied, and the dependence of the diffusivity on concentration can be described approximately using the Darken relationship. However, the diffusion of water in silica gel cannot be described by the nanopore diffusion model and is best characterized by the Glueckauf linear driving force model. The results illustrate the ability of concentration-swing frequency response to accurately determine adsorption rate mechanisms and quantify the complex adsorption kinetics of condensable vapors using small quantities of adsorbent.     

Study of polydimethylacrylamide- and polydiethylacrylamide-adsorbed coatings on fused silica capillaries and their application in genetic analysis

The adsorption of two polymers (polydimethylacrylamide and polydiethylacrylamide) on the inner surface of a fused silica of capillary (or wafer) was investigated by means of atomic force microscopy (AFM), multi-angle laser light scattering (MALLS) technique, and by measuring the electroosmotic flow (EOF) and contact angle. The AFM images showed that PDMA and PDEA tightly adsorbed on the fused silica surface and formed stable coatings. The contact angle data demonstrated that the polymer-adsorbed coatings have different hydrophobicities, which are related to the structures of the polymers. The adsorbing capability and stability of the adsorption coating, perhaps, were mainly dependent on the hydrogen bond force between oxygen atom on the carbonyl group of polymers and the hydroxyl group of the silica surface, and the hydrophobic nature of polymers. Our data also illustrated that the polymer-adsorbed coatings efficiently suppressed the EOF and the adsorption of DNA fragments on the capillary surface. These polymers were successfully used as sieving media in capillary electrophoresis of DNA fragments and detection of single point mutation of C677T from human methylenetetrahydrofolate reductase (MTHFR) gene.     

In situ determination of the thermodynamic surface properties of chemically modified surfaces on a local scale: an attempt with the atomic force microscope

We have monitored deflection-distance curves with an atomic force microscope (AFM) in contact mode, with a silicon nitride tip, on chemically modified silicon wafers, in the air. The wafers were modified on their surface by grafting self-assembled monolayers (SAMs) of different functional groups such as methyl, ester, amine, or methyl fluoride. A chemically modified surface with a functionalized hydroxyl group was also considered. Qualitative analysis allowed us to compare adhesive forces versus chemical features and surface energy. The systematic calibration procedure of the AFM measurements was performed to produce quantitative data. Our results show that the experimentally determined adhesive force or thermodynamic work of adhesion increases linearly with the total surface energy determined with contact angles measured with different liquids. The influence of capillary condensation of atmospheric water vapor at the tip-sample interface on the measured forces is discussed. Quantitative assessment values were used to determine in situ the SAM-tip thermodynamic work of adhesion on a local scale, which have been found to be in good agreement with quoted values. Finally, the determination of the surface energy of the silicon wafer deduced from the thermodynamic work of adhesion is also proposed and compared with the theoretical value.     

NMR Study of the Kinetics of Butane and Hexane Adsorption from Vapor Phase by Porous Glasses

The kinetics of butane and hexane sorption from vapor phase by porous glasses is studied by the pulsed NMR technique. The sorption process is revealed to proceed in two stages: monomolecular adsorption and capillary condensation. The rate of adsorption is limited by the rate of adsorbate transfer to the adsorbent surface, with the latter rate being described by the classical diffusion flux. It is shown that ultramicropores are filled simultaneously with the formation of a monolayer. The relative content of molecules in such pores is estimated. At the stage of monomolecular adsorption and at the initial stage of capillary condensation, when the adsorption proceeds from the vapor phase of butane-hexane or butane-deuterated hexane mixtures, butane molecules are predominantly sorbed and followed by their partial displacement by hexane molecules. The rate of the capillary condensation of butane from the mixture is 15–18-fold lower than that from the vapor phase of butane alone which is explained by a decrease in the gradient of chemical potential. It is shown that, when adsorption occurs from a nonequilibrium butane-hexane mixture, anomalous kinetic curves are observed because the driving force of adsorption changes in the course of establishing equilibrium in the liquid phase.     

Solvent effect on the aggregate of fluorinated gemini surfactant at silica surface

The aggregate states of partially fluorinated gemini surfactant [(CF3)2CF(CF2)2(CH2)10N(CH3)2]2(CH2)6Br2 (C(F)(5)C10-C6-C10C(F)(5)) on silica surface were investigated with atomic force microscopy (AFM) and water contact angle (CA) measurement by analyzing the effects of bulk concentration and adsorption time on stack state. On surfactant-adsorbed silica surfaces, there was a flat surface layer interspersed with some scattering surfactant aggregates. In the case of short adsorption times, the aggregates would be hemisphere. In the case of long adsorption times, the aggregates would be present in the form of bilayers. With the increase of bulk concentration, the adsorbed amount was enlarged and the surface layer became more compact. The formation of patchy bilayer aggregates indicated the saturation of the surface layer. Furthermore, organic solvent effects on the aggregate state of the surfactant on a silica surface were studied with four organic solvents, including n-hexane, dehydrated ethanol, 1,1,2-trichloro-1,2,2-trifluoroethane, and toluene. With the treatment of different organic solvents, the hemisphere aggregates on the surface layer can rearrange into spherical bilayer, rodlike monolayer, and branched rodlike monolayer aggregates, respectively. The polarity of solvents and affinity of organic solvents for surfactant molecules may have a great impact on the stack state of the fluorinated gemini surfactant molecules.     

Polymerized PolyHEMA photonic crystals: pH and ethanol sensor materials

The surface of monodisperse silica particles synthesized using the Stober process were coated with a thin layer of polystyrene. Surface charge groups were attached by a grafting polymerization of styrene sulfonate. The resulting highly charged monodisperse silica particles self-assemble into crystalline colloidal arrays (CCA) in deionized water. We polymerized hydroxyethyl methacrylate (HEMA) around the CCA to form a HEMA-polymerized crystalline colloidal array (PCCA). Hydrofluoric acid was utilized to etch out the silica particles to produce a three-dimensional periodic array of voids in the HEMA PCCA. The diffraction from the embedded CCA sensitively monitors the concentration of ethanol in water because the HEMA PCCA shows a large volume dependence on ethanol due to a decreased Flory-Huggins mixing parameter. Between pure water and 40% ethanol the diffraction shifts across the entire visible spectral region. We accurately modeled the dependence of the diffraction wavelength on ethanol concentration using Flory theory. We also fabricated a PCCA (which responds to pH changes in both low and high ionic strength solutions) by utilizing a second polymerization to incorporate carboxyl groups into the HEMA PCCA. We were also able to model the pH dependence of diffraction of the HEMA PCCA by using Flory theory. An unusual feature of the pH response is a hysteresis in response to titration to higher and lower pH. This hysteresis results from the formation of a Donnan potential at high pH which shifts the ionic equilibrium. The kinetics of equilibration is very slow due to the ultralow diffusion constant of protons in the carboxylated PCCA as predicted earlier by the Tanaka group.     

Effects of adsorbed water layer structure on adhesion force of silicon oxide nanoasperity contact in humid ambient

The origin of the large relative-humidity (RH) dependence of the adhesion force in the single-asperity contact between silicon oxide surfaces is elucidated. As RH increases, the adhesion force measured with an atomic force microscopy (AFM) initially increases, reaches a maximum, and then decreases at high RH. The capillary force alone cannot explain the observed magnitude of the RH dependence. The origin of the large RH dependence is due to the presence of an icelike structured water adsorbed at the silicon oxide surface at room temperature. A solid-adsorbate-solid model is developed calculating the contributions from capillary forces, van der Waals interactions, and the rupture of an ice-ice bridge at the center of the contact region. This model illustrates how the structure, thickness, and viscoelastic behavior of the adsorbed water layer influence the adhesion force of the silicon oxide nanoasperity contact.