Development of efficient method for preconcentration and determination of copper, nickel, zinc and iron ions in environmental samples by combination of cloud point extraction and flame atomic absorption spectrometry

A cloud point extraction procedure for the preconcentration of copper, nickel, iron and zinc ions in various samples has been described. Analyte ions in aqueous phase are complexed with 3-((indolin-3-yl)(phenyl)methyl)indoline (IYPMI) and following centrifugation quantitatively extracted to the aqueous phase rich in Triton X-114. The surfactant-rich phase was dissolved in 2.0 mol L⁻¹ HNO₃ in methanol prior to metal content determination by flame atomic absorption spectrometry (FAAS). The effects of some parameters including, the concentrations of IYPMI, Triton X-114 and HNO₃, bath temperature, centrifuge rate and time were investigated on the recoveries of analyte ions. At optimum conditions, the detection limits of (3 SDb m⁻¹) of 1.6, 2.8, 2.1 and 1.1 ng mL⁻¹ for Cu²⁺, Fe³⁺, Ni²⁺ and Zn²⁺ along with preconcentration factors of 30 and enrichment factor of 48, 39, 34 and 52 for Cu²⁺, Ni²⁺, Fe³⁺ and Zn²⁺ respectively, were obtained. The proposed cloud point extraction has been successfully applied for the determination of metal ions in real samples with complicated matrix such as biological, soil and blood samples with high efficiency.      

Separation, preconcentration and measurement of inorganic iron species by cloud point extraction and flow injection flame atomic absorption spectrometry

A sensitive and simple method for determination of iron species after separation/preconcentration by cloud point extraction (CPE) has been developed. When the temperature is higher than the cloud point extraction temperature (60 °C), the complexes of iron(II) and iron(III) species with ferron enter the surfactant-rich phase. Total amount of iron in the surfactant-rich phase was analyzed by FI-AAS, whereas, Fe(II) concentration was determined by a spectrophotometric method using mathematical equation to overcome the interference of Fe(III), when they are both present in the same solution. In this way the time-consuming and labor-intensive steps of preoxidation of Fe(II) or reduction of Fe(III) were eliminated. The parameters affecting could point extraction, such as concentrations of ferron and Triton X-114, pH, and equilibrium temperature were systematically investigated. Under the optimum conditions, the calibration curves were linear over the range of 10-250 and 5-150 μg l^-1 for 20 and 40 ml preconcentration volume, respectively. The detection limit was 1.7 μg l^-1, and relative standard deviation (RSD) was 2.1% for 20 ml preconcentration volume. The method was applied to the determination of iron species in water samples and total iron in milk. The accuracy was determined by recovery experiment, independent analysis by furnace atomic absorption spectrometry and analysis of certified reference water.     

Capillary electrophoretic separation and characterizations of CdSe quantum dots

We have developed a capillary electrophoresis method to characterize the QD surface ligand interactions with various surfactant systems. The method was demonstrated with 2–5 nm CdSe nanoparticles surface-passivated with trioctylphosphine oxide (TOPO). Water solubility was accomplished by surfactant-assisted phase transfer via an oil-in-water microemulsion using either cationic, anionic, or non-ionic surfactants. Interaction between the QD surface ligand (TOPO) and the alkyl chain of the surfactant molecule produces a complex and dynamic surface coating that can be characterized through manipulation of CE separation buffer composition and capillary surface modification. Additional characterization of the QD surface ligand interactions with surfactants was accomplished by UV-VIS spectroscopy, photoluminescence, and TEM. It is anticipated that studies such as these will elucidate the dynamics of QD surface ligand modifications for use in sensors.      

Review of recent developments of on-line sample stacking techniques and their application in capillary electrophoresis

Capillary electrophoresis (CE) has become one of the most useful tools in separation science because of its high separation efficiency, low cost, versatility, ease of sample preparation and automation. However, some limitations of CE, such as poor concentration sensitivity due to its lower sample loading and shorter optical path length, limits its further applications in separation science. In order to solve this problem, various on-line sample preconcentration techniques such as transient isotachophoresis preconcentration, field-enhanced sample stacking, micelle to solvent stacking, micelle collapse, dynamic pH junction, sweeping, solid phase extraction, single drop microextraction and liquid phase microextraction have been combined with CE. Recent developments, applications and some variants together with different combinations of these techniques integrating in CE are reviewed here and our discussions will be confined to the past three years (2008–2011).      

Hollow fibre liquid phase microextraction of parabens

A hollow fibre liquid phase microextraction for gas chromatographic determination of some p-hydroxybenzoic acid esters has been developed. Chlorobenzene containing tetradecane as internal standard was used for the extraction. Optimized extraction was carried out at room temperature for 40 min in the presence of 0.4 g mL⁻¹ NaCl in the sample solution. Calibration was linear up to 30 mg L⁻¹. Correlation coefficients were 0.996–0.998. Enrichment factors were 21, 95 and 154, and detection limits were 0.20, 0.03 and 0.01 μg mL⁻¹ for methylparaben, ethylparaben and propylparaben, respectively. Reproducibility was acceptable with relative standard deviations up to 11.7%. The technique was tested for water and urine analysis.      

Chromatographic separation of In(III) from Cd(II) in aqueous solutions using commercial resin (Dowex 50W-X8)

This work assesses the potential of an adsorptive material, Dowex 50w-x8, for the separation of indium ions from cadmium ions in aqueous media. The adsorption behavior of Dowex 50 w-x8 for indium and cadmium ions was investigated. The effect of pH, initial concentration of metal ions, the weight of resins, and contact time on the sorption of each of the metal ions were determined. It was found that the adsorption percentage of the indium ions was more than 99% at pH 4.0. The result shows that In (III) was most strongly extracted, while Cd(II) was slightly extracted at this pH value. The recovery of In(III) and Cd(II) ions is around 98% using hydrochloric acid as the best eluent.      

Solid phase selective separation and green preconcentration of Cu, Zn, Pb and Cd in drinking water by using novel functionalized resin

A new solid — phase extraction sorbent was developed based on stepwise anchoring of two ligand molecules for the determination of copper, zinc, lead and cadmium in drinking water by flame AAS. Amberlite XAD-2 functionalized with 4′-(2-hydroxyphenylazo)-3′-methyl-1′-phenyl-2′-pyrazolin-5′-one (HPAPyr) was utilized for preconcentration/separation of these elements. The sorbent was prepared by two successive azo coupling reactions. First, 2-aminophenol was anchored to the amino groups in the resin resulted from nitration followed by reduction. Then, the resulted 2-aminophenol functionalized resin was further diazotized and coupled to the pyrazolone compound and the final product HPAPyr-XAD-2 was characterized by IR and elemental analysis. The optimum pH range for sorption, shaking time, exchange capacity, sample flow rate, preconcentration factor and interference from co-existing ions were investigated. All metal ions were quantitatively desorbed from the resin by 4.5 mol L⁻¹ nitric acid solution. The sorbent provides limit of detection within the range 0.9–3.3 μg L⁻¹ and concentration factor up to 250. The procedure was validated by analysis of certified material NIST-SRM 1577b. Application to drinking water showed satisfactory results with relative standard deviation RSD ≤ 8.5%.      

Use of multivariate statistical techniques to optimize the separation of isoflavones by liquid chromatography

The aim of this paper is to optimize and validate a high performance liquid chromatography (HPLC) method for separation and quantification of five isoflavones. A statistical central composite design was used to separate all peaks. These multivariate procedures were efficient in determining the optimal separation condition using resolution, capacity factor, asymmetry and number of theoretical plates.      

Copper removal by carbon nanomaterials bearing cyclam-functionalized silica

The synthesis of metal (Fe, Co, Ni)-encapsulated carbon nanomaterials coated with cyclam-bonded silica has been described. The organic layer was identified by Fourier transform infrared spectroscopy and elemental analysis. The functionalized magnetic nanomaterials were employed to extract the divalent cations: copper, calcium, cobalt, manganese and nickel from aqueous solutions. Their adsorption capacities were studied by the batch procedure. The concentration of cations extracted was determined by inductively coupled plasma mass spectrometry. Influence of different parameters viz. pH, amount of the compound studied, contact time, on the cation extraction was investigated. Under optimum conditions copper extraction was significantly more efficient when compared with other coexisting ions.      

Selective separation of some ecotoxic transition metal ions from aqueous solutions using immobilized macrocyclic material containing solid phase extraction system

A simple flow-based method was developed for the simultaneous separation of certain transition metal ions (Co, Ni, Cu, Zn, Cd) from aqueous systems, which ions show ecotoxic effects when present at elevated concentrations. A silica-gel-bonded macrocycle system, commonly known as molecular recognition technology (MRT) gel, was used for solid phase extraction (SPE) of the target analytes. The collection behavior of the MRT-SPE system was studied based on pH. Fortified deionized water samples containing 250 μg L⁻¹ of each of the elements were treated at the flow rate of 1 mL min⁻¹. The collected analytes were then eluted by 3 M HNO₃ and analyzed using inductively coupled plasma spectrometry. Detection limits of the proposed technique were in the range of 0.004–0.040 μg L⁻¹ for the studied metal ions. The validity of this separation technique was checked with spiked ‘real’ water samples, which produced satisfactory recoveries of 96–102%. The non-destructive nature and highly selective ion-extraction capability of the SPE material are the most important aspects of the proposed method and they are the main focus of this paper.      

Optimization study of the catalytic activity of DNAzymes based on telomeric G-quadruplexes

Optimization studies of the procedure for peroxidase activity measurements with DNAzymes based on telomeric sequences and colorimetric indicator reactions are reported. Effect of metal cation, nature and concentration of surfactant, as well as thermal treatment of G-quadruplex sample are investigated. Nature of metal cation exhibited modest influence on the system performance. Great improvement of enzymatic activity of the telomeric quadruplexes in the presence of Brij 58 surfactant was observed. Further improvement of catalytic activity of the system based on human telomeric sequence was attained by applying a thermal treatment (heating/rapid cooling) procedure to prepare G-quadruplex/hemin complexes.      

Removal of cadmium and copper ions by <Emphasis Type="Italic">Trichosporon cutaneum</Emphasis> R57 cells immobilized onto polyvinyl alcohol/tetraethoxysilane hybrid matrices

Polyvinyl alcohol (PVA) and tetraethoxysilane (TEOS) hybrid materials were prepared by sol-gel methods and tested as matrices for immobilization of Trichosporon cutaneum R57, capable of removing cadmium and copper ions from aqueous solutions. A kinetic model was applied and the effects of matrix TEOS content on the copper and cadmium uptake equilibria and rate constants were investigated.      

Influence of surfactants on the fading of malachite green

The kinetics of the reaction between malachite green (MG) and sodium hydroxide (MG fading) was studied using a spectrophotometric method in the presence of two cationic surfactants, cetyl-benzyl-dimethyl-ammonium chloride (CBDAC) and hexadecyl-trimethylammonium bromide (HTAB) and one anionic surfactant, sodium dodecyl sulphate (SDS) at concentrations below and above critical micellar concentrations. The cationic surfactants have a catalytic effect, while the anionic surfactant has an inhibitory effect on the reaction. A kinetic model describing the influence of surfactant on reaction rate was developed. The results are discussed on the basis of electrostatic and hydrophobic interactions between the kinetic micelles and malachite green.      

Quick bioanalytical method of quantification and validation of sulbactam in plasma using high performance liquid chromatography

A quick method of quantitative determination of sulbactam in human plasma, using liquid chromatography-UV spectroscopy, has been developed and validated. After derivatization with imidazole, plasma samples were treated by direct deproteinization with acetonitrile as an extraction solvent. After ultracentrifugation, sulbactam extract was directly injected onto the LC column. Chromatographic separation was performed on TSK Gel Super ODS (50 mm × 4.6 mm i.d., 2 μm) using methanol and phosphate buffer with tetrabutylammonium hydroxide solution as a mobile phase. Gradient elution was employed. The method was fully validated according to the United States Food and Drug Administration requirements (linearity, precision, trueness, quantification limit, detection limit, recovery, specificity and stability). The calibration curves were linear within the concentration range of 0.05–4.0 μg mL⁻¹. Good method/system precision and accuracy of the method were demonstrated.      

Extraction of acyclovir from pharmaceutical creams for HPLC assay. Optimization and validation of pretreatment protocols

Three simple protocols for the extraction of acyclovir from its pharmaceutical creams based on ultrasonication, ultrasonication with heating and magnetic stirring were evaluated and compared. Extraction kinetics were studied at different time intervals (5, 10, 15, 30 and 60 min) and the extraction efficiency was determined by HPLC. The effect of concentration of aqueous NaOH as the extraction medium and the stirring speed were also studied and optimized. Best results were obtained with 50 mL of 0.01 mol L⁻¹ aqueous NaOH with magnetic stirring speed of 500 r.p.m. HPLC analysis involved rapid separation of acyclovir from the cream matrix using a 100 × 4.6 mm i.d. monolithic column and UV detection at 254 nm. Magnetic stirring produced the best results in terms of extraction efficiency with an average extraction yield of 100.8%, n = 16 at an optimum extraction time of 15 min. The selected protocol was validated for within and day-to-day precision and ruggedness.      

The binary system PbO - BiVO4

Phase equilibria established in the PbO - BiVO₄ system over the whole component concentration range up to 1000°C have been investigated. A phase diagram has been constructed using DTA and XRD.      

Recent progress for capillary electrophoresis with electrochemical detection

Capillary electrophoresis (CE) is an attractive technique in separation science because of its high separation performance, short analysis time and low cost. Electrochemical detection (EC) is a powerful tool for CE because of its high sensitivity. In this review, developments of CE-EC from 2008 to August, 2011 are reviewed. We choose papers of innovative and novel results to demonstrate the newest and most important progress in CE-EC.      

Alkylation of ambident indole anion in ionic liquids

Alkylation of indole salts in different ionic liquids is reported. Ionic liquids increase the alkylation reaction rate of ambident indole anion and reduce the effects of counter ions and/or additives, the alkylation reaction rates being independent of the presence of small amounts of protic solvents or water.      

Application of the ProteomeLab? PF2D protein fractionation system in proteomic analysis for human genetic diseases

Proteomic analysis has been widely used in elucidating the mechanism of diseases. As a classical proteomic approach, two-dimensional gel electrophoresis (2DGE) has been commonly applied in finding differentially expressed proteins through a first dimension of separation by the isoelectric point (pI) of proteins and a second dimension of separation according to the molecular weight (MW) of proteins. Compared to 2DGE, a recently developed commercial system from Beckman Coulter, the two-dimensional protein fractionation (PF2D), separates proteins according to the pI of proteins in the first dimension followed by a second dimension of separation according to the degree of protein hydrophobicity. As a liquid-based fractionation system, PF2D could facilitate the extraction and separation of broader protein categories and improve reproducibility and quantification as well as be less labor-intensive, which are usually identified as limitations of a gel-based 2DGE platform. This review evaluates the applications of the PF2D system and discusses the perspectives and advantages of PF2D in the investigation of cancer and genetic disorders and in protein mapping in human biological fluids and cell cultures.      

Sequential extraction and thermal desorption of mercury from contaminated soil and tailings from Mongolia

Mercury forms in contaminated environmental samples were studied by means of sequential extraction and thermal desorption from the solid phase. The sequential extraction procedure involved the following fractions: water soluble mercury, mercury extracted in acidic conditions, mercury bound to humic substances, elemental Hg and mercury bound to complexes, HgS, and residual mercury. In addition to sequential extraction, the distribution of mercury species as a function of soil particles size was studied. The thermal desorption method is based on the thermal decomposition or desorption of Hg compounds at different temperatures. The following four species were observed: Hg⁰, HgCl₂, HgS and Hg^(II) bound to humic acids. The Hg release curves from artificial soils and real samples were obtained and their applicability to the speciation analysis was considered.