The transport properties of the junction assembled by zigzag graphene nanoribbons (ZGNRs) and Au electrode (Au/ZGNR) are investigated using first‐principles calculations. It is found that the Au/ZGNR junction behaves as a typical diode with Schottky barrier at the contact. Our results indicate that although the oxidization at the contact slightly influences the Schottky barrier, the I –V characteristic is effectively modulated. Such effect derives from the impact of the oxidization on the coupling between the ZGNRs and Au electrode.
We report the fabrication procedure and the characterization of an Al0.3Ga0.7As solar cell containing high‐density GaAs strain‐free quantum dots grown by droplet epitaxy. The production of photocurrent when two sub‐bandgap energy photons are absorbed simultaneously is demonstrated. The high quality of the quantum dot/barrier pair, allowed by the high quality of nanostructured strain‐free materials, opens new opportunities for quantum dot based solar cells.
By means of first‐principles calculations we predict the stability of silicene as buckled honeycomb lattice on passivated substrates of group‐IV(111)1 × 1 surfaces. The weak van‐der‐Waals interaction between silicene and substrates does not destroy its linear bands forming Dirac cones at the Brillouin zone corners. Only very small fundamental gaps are opened around the Fermi level.
As electronic operating frequencies increase toward the terahertz regime, new electrooptic modulators capable of low‐voltage high‐frequency operation must be developed to provide the necessary optical interconnects. This Letter presents a new concept that exploits modulation instability to compensate for the intrinsically weak electrooptic effect, χ(2). Simulations demonstrate more than 50 times enhancement of electrooptic effect at millimeter wave frequencies leading to a substantial reduction in the required modulation voltage.
A very thin (250 nm), highly conductive (annealed), non‐texturized DC‐sputtered aluminum‐doped zinc oxide layer (ZnO:Al) deposited on a textured glass is used as substrate for thin‐film silicon solar cells. Compared to the classical approach, where wet‐chemically texturized ZnO:Al on planar glass is used, this approach allows a reduction in the as‐deposited ZnO:Al thickness of almost 70% while at the same time, thanks to the good light trapping capability of the glass texture the efficiency of the cells was maintained at the high level of 10.9%.
We report on the photoconductance in two‐dimensional arrays of gold nanorods. The arrays are formed by a combination of droplet deposition and stamping methods. We find that the plasmon induced photoconductance is sensitive to the linear polarization of the exciting photons consistent with the excitation of the longitudinal surface plasmon resonance of the nanorods.
We report a stacked Y2O3/TiOx resistive random access memory (RRAM) device, showing good high‐temperature switching characteristics of extremely low reset current of 1 μA at 150 °C, large off/on resistance window (>200) at 150 °C, large rectification ratio of ～300 at 150 °C and good current distribution at 85 °C. The good rectifying property, lower high‐temperature sneak current and tighter high‐temperature current distribution can be attributed to the combined results of the oxygen vacancies in TiOx and the related carrier depletion effect.
An improved power conversion efficiency (PCE) of bulk heterojunction organic photovoltaic cell (OPV) was achieved by inserting an n‐type [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) layer between the active layer and a metal electrode. The controlled substrate temperature was found to be a useful parameter for the multilayer structure (active layer/ PCBM) by the electrospray deposition method. Under optimized substrate temperature during the PCBM deposition, a multilayer structure could be formed, and the PCE was improved up to 1.94%.
Epitaxial TiC/SiC multilayers were grown by magnetron sputtering at a substrate temperature of 550 °C, where SiC is normally amorphous. The epitaxial TiC template induced growth of cubic SiC up to a thickness of ～2 nm. Thicker SiC layers result in a direct transition to growth of the metastable amorphous SiC followed by renucleation of nanocrystalline TiC layers.
Angle‐resolved photoemission spectroscopy (ARPES) and X‐ray photoemission spectroscopy have been used to characterise epitaxially ordered graphene grown on copper foil by low‐pressure chemical vapour deposition. A short vacuum anneal to 200 °C allows observation of ordered low energy electron diffraction patterns. High quality Dirac cones are measured in ARPES with the Dirac point at the Fermi level (undoped graphene). Annealing above 300 °C produces n‐type doping in the graphene with up to 350 meV shift in Fermi level, and opens a band gap of around 100 meV.
We report on wet etching of photomodified regions in crystalline sapphire using KOH solution. Tightly focused femtosecond laser pulses (150 fs at 800 nm wavelength) were used to create void structures enclosed in an amorphised sapphire shell inside the bulk of a crystalline host. The diameter of the amorphous regions can be controlled by pulse energy and was typically 0.5–1.5 µm. The etching rate depends on the distance between adjacent irradiation spots, pulse energy, concentration of etchant and ultrasonic agitation.
We demonstrate the self‐catalyst growth of vertically aligned InAs nanowires on bare Si(111) by droplet epitaxy. The growth conditions of indium droplets suitable for nucleation and growth of nanowires have been identified. We have then realized vertically aligned and non‐tapered InAs nanowires on bare Si(111) substrates through optimal indium droplets. It was found that the lateral dimensions and density of nano‐wires are defined by the indium droplets. This technique unravels a controllable, cost‐effective and time‐efficient route to fabricating functional monolithic hybrid structures of InAs nanowires on silicon.
We demonstrate the fabrication of a solid state heterojunction photovoltaic device with solution‐processed graphene oxide (GO) and n‐Si. Partially reduced GO with a high optical gap (2.8 eV) was spin‐coated on the n‐Si substrate and a heterojunction device was fabricated with the structure of Au/pr‐GO/n‐Si. In the fabricated device, incident light was transmitted through the thin GO film to reach the junction interface, generating photoexciton, and thereby a photovoltaic action was observed. By means of a built‐in electric potential at the GO/n‐Si junction, photoexcited electrons and holes can be separated, transported and collected at the electrodes.
We present experimental and theoretical evidence of the role played by the spin–orbit coupling in the electronic structure of a pseudomorphic Au monolayer on Nb(001) substrate. The bands found with the help of the angle‐resolved ultraviolet photoelectron spectroscopy (ARUPS) are compared with those obtained from ab initio self‐consistent calculations by the VASP and WIEN2k codes. The slab calculations are performed including geometric relaxation and using both the generalized‐gradient (GGA) and local‐density (LDA) approximations for the exchange–correlation energy. The dispersions and energy positions of the calculated bands agree with the experimentally determined band structure only if the LDA is used and the spin–orbit coupling is included. Therefore, both the structure relaxation and spin–orbit coupling are essential in understanding the electronic structure of the Au/Nb(001) system.
A facile metal catalyst free route to synthesize boron doped (0.6%–1.0%) carbon nanotubes via ceramic nanowires in which the formation of the nanowires (probably serving as templates), the carbon nanotubes and their doping all occur unanimously in the reaction, is presented.
Write‐once–read‐many‐times memory (WORM) devices were fabricated using Ti/Au and Au as top contacts on ZnO thin films on Si. Electrical characterization shows that both types of WORM devices have large resistance OFF/ON ratio (R ratio), small resistance distribution range, long retention and good endurance. WORM devices with Au top contact have better performance of higher R ratio because of a larger work function of Au compared to Ti.
Spin crossover compounds are considered to be a viable alternative for creating display, memory and switching devices due to the bistability of their magnetic, optical, mechanical and electrical properties. This Letter presents the study of the dielectric and transport properties of the [Fe(Htrz)2(trz)](BF4) (Htrz = 1H‐1,2,4‐triazole) complex in a wide temperature and frequency range. Our results reveal a singular behavior of the dielectric modulus upon the spin transition in conjunction with the switching of the conductivity between the high spin and low spin states.
Heteroepitaxial growth of kesterite Cu2ZnSnS4 (CZTS) thin film on cubic ZnS(100) single crystal substrate was achieved by radio frequency magnetron sputtering from a single CZTS target. An optimal substrate temperature in the range of 470–500 °C is found suitable for this epitaxial growth. The growth of CZTS was confirmed to be along a‐axis. The sputtered CZTS thin film is homogeneous throughout the whole film. The band gap of the film is found to be approximately 1.51 eV, i.e., promising for high efficiency thin film solar cells.
Nanostructures formed in a titanium dioxide (TiO2)–poly(styrene)‐block‐poly(ethyleneoxide) nanocomposite film on top of fluor‐doped tin oxide (FTO) layers are investigated. The combinatorial approach is based on probing a wedge‐shaped FTO‐gradient with grazing incidence small angle X‐ray scattering (GISAXS) in combination with a moderate micro‐focus X‐ray beam. The characteristic lateral length is given by adjacent nanowire‐shaped TiO2 regions. It decreases from 200 nm on the thick FTO layer to 90 nm on the bare glass surface.
