Metal-electrode-free inverted organic photovoltaics using electrospray-deposited PEDOT:PSS and spin-coated HAT-CN exciton blocking layer

Poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonate) (PEDOT:PSS) films were fabricated using an electrospray deposition (ESD) method. The ESD PEDOT:PSS films exhibited higher PSS content on the surface than spin-coated PEDOT:PSS films, which results in a higher work function. Based on this result, metal-electrode-free inverted organic photovoltaics (OPVs) were fabricated. The ESD PEDOT:PSS was used as the top electrode on the poly(3-hexythiophene-2,5-diyl) (P3HT):[6,6]-phenyl C₆₁ butyric acid methyl ester (PCBM) light-absorbing layer. The power conversion efficiency (PCE) of OPVs was significantly increased with the 1,4,5,8,9,11-hexaazatriphenylene hexacarbonitrile layer. The improved PCE would be attributed to the suppression of exciton quenching at the P3HT:PCBM and PEDOT:PSS interface.     

Investigating the performance of P3HT:PCBM organic solar cells involving gamma-irradiated PEDOT:PSS layer

In this work, we investigated for the first time the characteristics of (poly (3-hexylthiopene) and [6, 6]-phenyl C61-butyric acid methyl ester) (P3HT:PCBM) blends-based organic solar cell with 1.25?mg/mL boric-acid (H₃BO₃)-doped poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) layer which is irradiated under the 40 Gray (Gy) dose of gamma (γ) ray. Experimental results showed that the parameters of solar cell improved with exposure to low-dose gamma radiation. In particular, it has provided a significant improvement in short-circuit current density (J_sc) and power conversion efficiency (PCE). About 49% increase in PCE to 1.22% and 40% increase in J_sc to 6.28?mA/cm² was obtained between the bare device and the device containing irradiated PEDOT:PSS:H₃BO₃. Also, it was determined that the H₃BO₃-doped PEDOT:PSS is more stable to temperature. More importantly, solar cell containing gamma-irradiated PEDOT:PSS:H₃BO₃ showed best performance comparing to conventional PEDOT:PSS-based cell.     

PEDOT:PSS Schottky contacts on annealed ZnO films

Polycrystalline ZnO and ITO films on SiO₂ substrates are prepared by radio frequency (RF) reactive magnetron sputtering. Schottky contacts are fabricated on ZnO films by spin coating with a high conducting polymer, poly(3, 4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) as the metal electrodes. The current-voltage measurements for samples on unannealed ZnO films exhibit rectifying behaviours with a barrier height of 0.72 eV (n=1.93). The current for the sample is improved by two orders of magnitude at 1 V after annealing ZnO film at 850 ℃, whose barrier height is 0.75 eV with an ideality factor of 1.12. X-ray diffraction, atomic force microscopy and scanning electron microscopy are used to study the properties of the PEDOT:PSS/ZnO/ITO/SiO₂. The results are useful for applications such as metal-semiconductor field-effect transistors and UV photodetectors.     

Fractality in the neuron axonal topography of the human brain based on 3-D diffusion MRI

We report our results on the effect of incorporation of inorganic fullerene like nanoparticles (IF) and inorganic nanotubes (INT) of WS₂ into hybrid LED device structures. To disperse into a uniform fashion, the semiconducting INT/IF WS₂ NTs were functionalized with SDS (sodium dodecylsulphate). The IF/INT WS₂ nanotubes were used in combination with PEDOT:PSS and P3HT to realize the following LED device structures: ITO/(PEDOT:PSS):(WS₂:SDS)/P3HT/LiF-Al; ITO/PEDOT:PSS/P3HT/WS₂:SDS/LiF-Al. Morphological, optical and electrochemical analysis were performed to obtain the HOMO and the LUMO energy levels to hypothesize the most efficient device structure. The spectral positions of the electroluminescent bands were found out to be device-dependent and exhibits blue shift when the proposed nanostructure is dip coated on top of P3HT. Electro-optical analysis indicate that the WS₂:SDS based P3HT/semiconductor film can improve the charge recombination probability owing to its dual functionality as hole blocking layer and electron injection moiety.     

紫外臭氧处理超薄银修饰ITO电极的高效柔性有机太阳能电池

以紫外臭氧处理超薄Ag复合MoO₃或PEDOT：PSS修饰ITO电极的高效柔性有机太阳能电池。通过优化紫外臭氧处理Ag薄膜的时间,提高了以P3HT：PCBM为有源层的器件的功率转换效率,从1.68%（未经过紫外臭氧处理）提高到2.57%（紫外臭氧处理Ag 1 min）。提高的原因推测是紫外臭氧处理形成了AgO_x薄膜,提高了电荷提取并使器件具有高光学透明度、低串联电阻和优异的表面功函数等一些性能。并且,紫外臭氧处理Ag薄膜与MoO₃或者PEDOT：PSS复合修饰ITO的器件效率分别得到提高,Ag薄膜与MoO₃复合修饰ITO的器件效率从2.02%（PET/ITO/MoO₃）提高到2.97%（PET/ITO/AgO_x/MoO₃）,Ag薄膜与PEDOT：PSS复合修饰ITO的器件效率从2.01%（PET/ITO/PEDOT：PSS）提高到2.93%（PET/ITO/AgO_x/PEDOT：PSS）。此外,以PBDTTT-EFT：PC₇₁BM为有源层的柔性聚合物太阳能电池效率可达6.21%。基于ITO的柔性光电器件效率的提高主要归于ITO被Ag/PEDOT：PSS或Ag/MoO₃修饰后功函数的提高。     

Polymer solar cells based on a PEDOT:PSS layer spin-coated under the action of an electric field

In the process of fabrication of polymer photovoltaic(PV) devices,poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)(PEDOT:PSS) thin film,acting as an anode buffer layer,is spin-coated under the action of an electric field.The PV devices with a PEDOT:PSS layer spin-coated under the action of a static electric field exhibit improved short-circuit current density(J sc) and power conversion efficiency(PCE).The investigation of morphology shows that the appropriate intensity of the electric field can increase the roughness of the surface of the PEDOT:PSS layer,which results in improved contact between the anode and hole transport layer and thus enhances the J sc of the devices.Chemical analysis is also provided by x-ray photoelectron spectroscopy(XPS) spectra.     

Improving efficiency of inverted perovskite solar cells via ethanolamine-doped PEDOT:PSS as hole transport layer

In order to fabricate high-performance inverted perovskite solar cells (PeSCs), an appropriate hole transport layer (HTL) is essential since it will affect the hole extraction at perovskite/HTL interface and determine the crystallization quality of the subsequent perovskite films. Herein, a facile and simple method is developed by adding ethanolamine (ETA) into poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as HTL. The doping of a low-concentration ETA can efficiently modify the electrical properties of the PEDOT:PSS film and lower the highest occupied molecular orbital (HOMO) level, which is more suitable for the hole extraction from the perovskite to HTL. Besides, ETA-doped PEDOT:PSS will create a perovskite film with larger grain size and higher crystallinity. Hence, the results show that the open-circuit voltage of the device increases from 0.99 V to 1.06 V, and the corresponding power conversion efficiency (PCE) increases from 14.68% to 19.16%. The alkaline nature of ethanolamine greatly neutralizes the acidity of PEDOT:PSS, and plays a role in protecting the anode, leading the stability of the devices to be improved significantly. After being stored for 2000 h, the PCE of ETA-doped PEDOT:PSS devices can maintain 84.2% of the initial value, which is much higher than 67.1% of undoped devices.     

掺杂PEDOT ∶PSS对聚合物太阳能电池性能影响的研究

研究了掺杂后poly(3,4-ethylene dioxythiophene):poly(styrenesulphonic acid)(PEDOT ∶PSS)电导率的变化以及掺杂PEDOT ∶PSS薄膜对聚合物太阳能电池器件性能的影响. 实验发现,向PEDOT ∶PSS中掺入极性溶剂二甲基亚砜(DMSO)明显提高了薄膜的电导率,掺杂后的电导率最大值达到1.25 S/cm,比未掺杂时提高了3个数量级. 将掺杂的PEDOT ∶PSS薄膜作为缓冲层应用于聚合物电池 (ITO/PEDOT ∶PSS/P3HT ∶PCBM/LiF/Al) 中,发现高电导率的PEDOT ∶PSS降低了器件的串联电阻,增加了器件的短路电流,从而提高了器件的性能. 最好的聚合物太阳能电池在100 mW/cm²的光照下,开路电压(V_oc)为0.63 V,短路电流密度(J_sc)为11.09 mA·cm^-2,填充因子(FF)为63.7%,能量转换效率(η)达到4.45%. 关键词： PEDOT ∶PSS 电导率 聚合物太阳能电池 能量转换效率     

金纳米四面体增强有机太阳电池光吸收及光伏性能研究

为增强有机太阳能电池的光利用率,提高能量转换效率,本文合成了金四面体形状的纳米粒子,并用聚苯乙烯磺酸钠(PSS)包裹形成了核壳结构的金纳米四面体(Au@PSS tetrahedra NPs).将其掺杂到有机太阳能电池空穴提取层与活性层的界面处,利用表面等离子体共振效应来增强活性层对光的吸收,从而提高有机太阳能电池的能量转换效率.研究了掺杂浓度和PSS包裹厚度对电池性能的影响.结果表明:掺杂浓度为6%时,器件性能最佳,能量转换效率达到3.08%; PSS壳层厚度优化为2.5 nm时,转换效率达到3.65%,较标准电池提升了22.9%.电池性能的改善主要源于金四面体纳米粒子的共振吸收峰位于给体材料吸收谱范围内,纳米粒子的共振促进了给体的吸收,同时PSS壳层的引入促进了激子的解离和电荷的转移,上述因素的改善提升了电池的短路电流、填充因子和转换效率.     

Microwave-reduced graphene oxide for efficient and stable hole extraction layers of polymer solar cells

Microwave-assisted reduced graphene oxide (MR-GO) layer was applied to hole extraction layer (HEL) of polymer solar cells (PSCs) and was compared with the widely used poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) in bulk hetero-junction (BHJ) solar cells. The power conversion efficiency (PCE) of 3.57% was achieved with the MR-GO layer, which is 21% higher than that of PSCs with the conventional PEDOT:PSS HEL material. This enhancement of PCE is mainly attributed to the increase of short-circuit current density originated from the hydrophobic surface of the MR-GO layer. The hydrophobic graphene oxide surface is believed to improve wetting property and physical contact of active blends. In addition, the MR-GO interfacial layer is found to show the excellent device stability in atmospheric condition. The PCE of conventional PEDOT:PSS based PSCs showed total degradation when the device was exposed to atmospheric condition for 1000 h without any encapsulation, while that of MR-GO based PSC showed over 85% of PCE.     

Ultrasonically prepared photocatalyst of W/WO3 nanoplates with WS2 nanosheets as 2D material for improving photoelectrochemical water splitting

A sonochemical treatment has been an emerged technique as an interesting method for fabricating different photocatalysts with unique photoelectrochemical (PEC) properties. This study investigated the PEC performance of WO₃ with WS₂ nanosheets as a 2D material before calcination (WO₃/WS₂-90) and after calcination (WO₃/WS₂-450) prepared with sonochemical treatment. The WS₂ nanosheets were prepared from a liquid exfoliation phase with few-layer nanosheets, approximately 6.5 nm in thickness. The nanosheets were confirmed by UV–Vis spectroscopy and atomic force microscopy. Further, XPS, RAMAN, and SEM-EDAX analyses indicated that, following calcination of the WO₃/WS₂ electrode, the WS₂ nanosheets initially transformed to 2D-WO₃. After depositing the WS₂ nanosheets on the WO₃, the photocurrent density increased substantially. The WO₃/WS₂-450 films after calcination showed a photocurrent density of 5.6 mA.cm⁻² at 1.23 V vs. Ag/AgCl, which was 3.1 and 7.2 times higher, respectively than those of the WO₃/WS₂-90 before calcination and pure WO₃. Mott-Schottky and electrochemical impedance spectroscopy analyses confirmed the fabrication of the WO₃/WS₂ photoanode after calcination. The deposition of WS₂ nanosheets onto pure WO₃ increased the donor concentration (24-fold), reduced the space charge layer (4.6-fold), and decreased the flat band potential (1.6-fold), which could all help improve the photoelectrochemical efficiency. Moreover, the incorporation of WO₃ with WS₂ nanosheets as a 2D material (WO₃/WS₂-450) enhanced the incident photon current efficiency (IPCE) by 55%. In addition, the applied-bias photon-to-current conversion efficiency of the WO₃/WS₂-450 films was approximately 2.26% at 0.75 V (vs. Ag/AgCl), which is 5.6 and 9 times higher, respectively than those of WO₃/WS₂-90 and pure WO₃.     

Increased work function in PEDOT:PSS film under ultraviolet irradiation

An increase of work function （0.3 eV） is achieved by irradiating poly（3,4-ethylenedioxythiophene）：poly（styrene sul- fonate） （PEDOT：PSS） film in vacuum with 254-nm ultraviolet （UV） light. The mechanism for such an improvement is investigated by photoelectron yield spectroscopy, X-ray photo electron energy spectrum, and field emission technique. Sur- face oxidation and composition change are found as the reasons for work function increase. The UV-treated PEDOT：PSS film is used as the hole injection layer in a hole-only device. Hole injection is improved by UV-treated PEDOT：PSS film without baring the enlargement of film resistance. Our result demonstrates that UV treatment is more suitable for modifying the injection barrier than UV ozone exposure.     

退火温度对电子束蒸发沉积Cu_2O薄膜性能的影响

近年来,钙钛矿太阳电池(PSCs)得到了迅猛发展,而无机空穴传输材料(IHTMs)的使用可进一步降低电池的成本,提高电池的稳定性.本文通过电子束蒸发制备了Cu_2O薄膜,研究了空气中退火温度及时间对薄膜组成、结构及光电性能的影响,并构筑了p-i-n反型平面异质结钙钛矿太阳电池.研究发现:由于热解作用,直接通过电子束蒸发制备的薄膜为Cu_2O和Cu的混合物;而在空气中经过退火后,由于氧化作用,随着退火温度的升高,薄膜的组分由混合物转变为纯的Cu_2O,再转变成纯的CuO.通过控制退火温度制备的Cu_2O薄膜的光学带隙约为2.5 eV,载流子迁移率约为30 cm~2·V~(-1)·s~(-1).应用于PSCs,薄膜的最佳厚度为40 nm,但电池性能低于PEDOT:PSS基的PSCs.这主要是由于钙钛矿前驱液在Cu_2O薄膜的润湿性较差,吸收层中有大量微孔洞存在,致使漏电流增强,电池的性能降低.然而,当采用Cu_2O/PEDOT:PSS双HTMs设计时,由于PEDOT:PSS对Cu_2O具有较强的腐蚀作用,使电池性能恶化.     

Improving the performance of perovskite solar cells with glycerol-doped PEDOT:PSS buffer layer

In this paper, we investigate the effects of glycerol doping on transmittance, conductivity and surface morphology of poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate))(PEDOT:PSS) and its influence on the performance of perovskite solar cells.. The conductivity of PEDOT:PSS is improved obviously by doping glycerol. The maximum of the conductivity is 0.89 S/cm when the doping concentration reaches 6 wt%, which increases about 127 times compared with undoped. The perovskite solar cells are fabricated with a configuration of indium tin oxide(ITO)/PEDOT:PSS/CH_3NH_3PbI_3/PC_(61)BM/Al, where PEDOT:PSS and PC_(61)BM are used as hole and electron transport layers, respectively. The results show an improvement of hole charge transport as well as an increase of short-circuit current density and a reduction of series resistance, owing to the higher conductivity of the doped PEDOT:PSS. Consequently, it improves the whole performance of perovskite solar cell. The power conversion efficiency(PCE) of the device is improved from 8.57% to 11.03% under AM 1.5 G(100 mW/cm~2 illumination) after the buffer layer has been modified.     

Enhanced thermoelectric properties of PEDOT/PSS/Te composite films treated with H<Subscript>2</Subscript>SO<Subscript>4</Subscript>

Firstly, tellurium (Te) nanorods with a high Seebeck coefficient have been integrated into a conducting polymer PEDOT/PSS to form PEDOT/PSS/Te composite films. The Seebeck coefficient of the PEDOT/PSS/Te (90 wt.%) composite films is ~191 μV/K, which is about 13 times greater than that of pristine PEDOT/PSS. Then, H₂SO₄ treatment has been used to further tune the thermoelectric properties of the composite films by adjusting the doping level and increasing the carrier concentration. After the acid treatment, the electrical conductivity of the composite films has increased from 0.22 to 1613 S/cm due to the removal of insulating PSS and the structural rearrangement of PEDOT. An optimized power factor of 42.1 μW/mK² has been obtained at room temperature for a PEDOT/PSS/Te (80 wt.%) sample, which is about ten times larger than that of the untreated PEDOT/PSS/Te composite film.     

Water‐Soluble Monolayer Molybdenum Disulfide Quantum Dots with Upconversion Fluorescence

Uniform water‐soluble monolayer MoS₂ quantum dots (MQDs) with lateral sizes of ≈2.1 nm, a clearly zigzag‐terminated edge, and a hexagonal lattice structure are achieved using ammonium molybdate, thiourea, and N‐acetyl‐l ‐cysteine (NAC) as precursors and the capping reagent in a facile one‐pot hydrothermal approach. MQDs have good dispersity and high stability in aqueous suspension and exhibit a significantly larger direct bandgap (3.96 eV) compared to monolayer MoS₂ nanosheets (1.89 eV). Pronounced blue‐shifts in the wavelengths of both the excitonic absorption and intrinsic state emission with activated strong luminescence at room temperature beyond monolayer MoS₂ nanosheets is demonstrated. Unusual upconversion photoluminescence is also observed and is caused by two successive transfers of energy from the near‐infrared (NIR) absorption generated by the NAC capping reagent to the hexagonal structure of MQDs. Additional optical properties of MQDs may provide numerous exciting technological applications. Here, MQDs are demonstrated as a highly selective fluorescent reagent for detecting tetracycline hydrochloride under UV and NIR irradiation.     

Liquid‐Crystal‐Mediated Self‐Assembly of Porous α‐Fe2O3 Nanorods on PEDOT:PSS‐Functionalized Graphene as a Flexible Ternary Architecture for Capacitive Energy Storage

A novel aqueous‐based self‐assembly approach to a composite of iron oxide nanorods on conductive‐polymer (CP)‐functionalized, ultralarge graphene oxide (GO) liquid crystals (LCs) is demonstrated here for the fabrication of a flexible hybrid material for charge capacitive application. Uniform decoration of α‐Fe₂O₃ nanorods on a poly(3,4‐ethylene‐dioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)‐functionalized, ultralarge GO scaffold results in a 3D interconnected layer‐by‐layer (LBL) architecture. This advanced interpenetrating network of ternary components is lightweight, foldable, and possesses highly conductive pathways for facile ion transportation and charge storage, making it promising for high‐performance energy‐storage applications. Having such structural merits and good synergistic effects, the flexible architecture exhibits a high specific discharge capacitance of 875 F g^?1 and excellent volumetric specific capacitance of 868 F cm^?3 at 5 mV s^?1, as well as a promising energy density of 118 W h kg^?1 (at 0.5 A g^?1) and promising cyclability, with capacity retention of 100% after 5000 charge–discharge (CD) cycles. This synthesis method provides a simple, yet efficient approach for the solution‐processed LBL insertion of the hematite nanorods (HNR) into CP‐functionalized novel composite structure. It provides great promise for the fabrication of a variety of metal‐oxide (MO)‐nanomaterial‐based binder and current collector‐free flexible composite electrodes for high‐performance energy‐storage applications.     

Performance and stability studies of inverted polymer solar cells with TiO2 film as a buffer layer

TiO₂ based inverted polymer solar cells (PSCs) with a structure of fluorine-doped tin oxide (FTO)/TiO₂/P3HT:PCBM/PEDOT:PSS/Ag presented excellent air stabilities,; the power conversion efficiency (PCE) of devices exhibited only 15 % decay as compared to the highest value while being exposed in air-condition for more than 20 days. Interestingly, an overall enhancement of PCE from 3.5 % to 3.9 % was observed while the PSCs were exposed in air-condition up to 3 days; the improvement of performance was attributed to the TiO₂ films’ oxygen and water protection effect and the oxidation of Ag, which will benefit to form an effective work function match with the HOMO of P3HT leading to improved ohmic contact. However, the performance slowly decreased when the exposure time remains longer due to the physical adsorbed oxygen. UV–ozone treatment on the TiO₂ films’ leads to the formation of a metal-deficient oxide that results in a decreased PCE for the devices. Finally, X-ray photo-emission spectroscopy (XPS) was used to analyze the compositional changes of the TiO₂ films while they were exposed in air-condition or treated by UV–ozone.     

Free-standing WS<Subscript>2</Subscript><Emphasis Type="Strikethrough">-</Emphasis>MWCNTs hybrid paper integrated with polyaniline for high-performance flexible supercapacitor

As two-dimensional layered nanomaterials, the tungsten disulfide (WS₂) nanosheets can be used as building blocks of paper-like electrodes for high-performance FSs. However, poor conductivity and mechanical property of WS₂ nanosheets (NSs) paper greatly hinders their capacitance and/or rate performance. To solve these problems, we fabricated the WS₂-multiwalled carbon nanotubes (MWCNTs)/polyaniline (PANI) composite papers based on liquid exfoliation and electrochemical deposition for high-performance flexible supercapacitors. The WS₂-MWCNTs/PANI with conductive PANI chains linked WS₂ NSs and MWCNTs takes the advantages of high-electronic double-layer capacitance originated from the internal surface areas of MWCNTs and effective pseudocapacitance generated by exfoliated WS₂ NSs and PANI. Electrochemical studies showed that the gravimetric-specific capacitance of WS₂-MWCNTs/PANI can reach ~760.1 F/g at a current density of 1 A/g. A symmetric flexible solid-state supercapacitor was also assembled and studied. The WS₂-MWCNTs/PANI-assembled FS device also has an excellent area specific capacitance of 1158.7 mF/cm² at a current density of 0.5 mA/cm² together with a high-capacity retention of ~82.5% after 2000 cycles.     

Pentacene as a hole transport material for high performance planar perovskite solar cells

A cost-effective and efficient organic semiconductor pentacene was developed as a hole transport layer (HTL) material to replace classical PEDOT:PSS for planar perovskite solar cells (PSCs). As expected, the pentacene based device exhibits power conversion efficiency (PCE) of 15.90% (J_sc of 19.44 mA/cm², V_oc of 1.07 V, and FF of 77%), comparable to the PEDOT:PSS based device (PCE of 15.65%, J_sc of 18.78 mA/cm², V_oc of 1.07 V, and FF of 77%) under the same experimental conditions. The excellent performance of vacuum deposited pentacene is mainly attributed to the high efficient charge extraction and transfer in device due to the high-quality perovskite film grown on the top of pentacene substrate and a favorable energy-level alignment together with a desired downward band bending formed at the perovskite/pentacene interface. Our research has confirmed that pentacene could be served as a promising HTL material to achieve effective and potentially economical planar type PSCs.