Gyrotron based on a superconducting magnet

The replacement of conventional pulsed magnetic field coils previously used to generate the intra-cavity B-field with an 11T superconducting magnet is reported. The resulting more stable mm-wave output pulse is shown and the refurbishment requirements of both the field emission, field-immersed, cold cathode and Marx bank spark gaps demonstrated. This system proved to be tunable, oscillating from 20GHz up to 110GHz, with peak power levels of 450kW and 300kW respectively. Other operating parameters were also examined including mm-wave pulse length as a function of anode-cathode position. The pulse length increased from 87±6ns to 310±10ns with a 2.5 cm horizontal transit of the cathode away from the anode. A similar effect was witnessed with the increase of the intra-cavity B-field from 1.00T to 5.00T resulting in the mm-wave pulse duration increasing from 250±40ns. Second harmonic operation of the cavity resulted in 0.5kW of radiation observed at 96GHz. The pulse-to-pulse mm-wave stability coupled with the mode selectivity of the ohmic-Q-dominated cavity resulted in the identification of several oscillating modes including the TE₁₂, cut-off frequency 21.1 GHz, the TE₀₂, cut-off frequency 29.1 GHz, the TE₃₅ at 74 GHz and the TE_14,2, at 88GHz.     

Frequency Sources in W-band Radar Front-end with Low Phase Noise

A W-band coherent stepped-frequency pulsed radar front-end is developed. It consists of a millimetre wave transmitting source, a mm-wave local source, a DDS with multi frequency points output and two microwave sources serving as local oscillators. All the sources are coherent with the 120 MHz referenced crystal oscillator. The mm-wave sources are realized by frequency multiplier chain, up-conversion and injection locking. The phase noise of fundamental-wave injection-locked W-band harmonic Gunn oscillator output signal achieves −98 dBc/Hz at 10 kHz offset and the spurious output is less than −50 dBc. The received intermediate frequency signal is also presented.     

Array design for mm-wave UAV-assisted cooperative communications with simultaneous wireless information and power transmission

High performance UAV-assisted communications system using simultaneous wireless information and power transmission (SWIPT) in mm-wave band is presented. UAV is a moving relay powered from a ground source through a power-splitting mechanism. In mm-wave band we utilize antenna array to increase the antenna gain while keeping array size small and practical. The radiation pattern of the UAV antenna is continuously adjusted to peak towards the source and destination. Two array geometries, a line and a cross, are designed for UAV antenna. We achieve near optimal pattern, utilizing innovative low power switches instead of phase shifters which are high power consuming components and using them here defies the purpose. We maximize the end-to-end cooperative throughput by optimizing the UAV power profile, power-splitting ratio profile, antenna weights (0, 1), and UAV trajectory for amplify-and-forward (AF) protocol. We consider two cases. Case1: UAV transmits and receives data simultaneously along two predefined trajectories. The antenna weights for line and cross arrays are optimized utilizing genetic algorithm. The power profile and, power-splitting ratio profile are also optimized using the penalty method. Case2: UAV accumulates the data and power along an optimal trajectory until it reaches the vicinity of target, when it transmits data at high bit rate. Here we define the optimization of parameters mentioned in Case1, while at an optimal point along the trajectory, as sub-problem1, and finding the next optimal point as sub-problem2. Sub-problem1 is solved using the genetic algorithm and dual decomposition method. Sub-problem2 is then solved using successive concave optimization. The overall problem, i.e. cooperative throughput, is solved by reciprocal iteration over the two sub problems. The simulation results show the proposed mm-wave band cross array antenna and switches can overcome the high frequency propagation losses, hence, achieving higher power harvest and data rates. The achieved higher data throughput outperforms the conventional single antenna low frequency systems.     

A full-duplex radio-over-fiber system using direct modulation laser to generate optical millimeter-wave and wavelength reuse for uplink connection

In this paper, we present a full-duplex radio-over-fiber system incorporating both optical millimeter-wave (mm-wave) generation and wavelength reuse for uplink connection. The optical double sidebands (DSB) signal is generated by using only one inexpensive broadband direct modulation laser (DML), to which a mixing RF signal is applied. An optical interleaver is then used to separate the first-order optical sidebands from the optical carrier of optical DSB signal. The separated first-order optical sidebands are beat to generate mm-wave signal that has double the frequency of the RF drive signal, while the separated optical carrier is reused as light source to remodulate uplink signal. Both detailed theoretical analysis and experiments to demonstrate the feasibility of the proposed system are presented. Experiment result shows that the bidirectional 2.5 Gb/s data can be successfully transmitted over 40 km standard single-mode fiber (SSMF) with less than 2 dB power penalty.     

Generation of optical carrier suppression millimeter-wave signal using one dual-parallel MZM to overcome chromatic dispersion

In this paper, we have proposed a novel approach to generate optical carrier suppression (OCS) mm-wave with signal only carried by one first-order sideband using a dual-parallel MZM in radio-over-fiber (RoF) system, and the transmission performance was also investigated. As the optical mm-wave signal is transmitted along the fiber, there is no time shift of the data symbols resulting from the group velocity dispersion in the fiber because the signal is only modulated on one sideband. The simulation results showed that the eye diagram keeps open and clear even when the optical mm-wave signals are transmitted over 96-km and the power penalty is about 1-dB after fiber transmission distance of 60-km, which is quite consistent with our theoretical analysis. Furthermore, the proposed OCS optical mm-wave generation approach is also used in a full-duplex RoF link based on wavelength reuse at the base station for the uplink due to another pure sideband without carrying data. The bidirectional 2.5-Gbit/s data is successfully transmitted over 40-km standard single mode fiber with less than 0.5-dB power penalty in the simulation. Both the unidirectional RoF downlink and the full-duplex RoF system have good performance.     

High-power picosecond LiB3O5 optical parametric oscillators tunable in the blue spectral range

The paper reports on an experimental investigation and numerical analysis of noncritically and critically phasematched LiB₃O₅ (LBO) optical parametric oscillators (OPOs) synchronously pumped by the third harmonic of a cw diode-pumped mode-locked Nd:YVO₄ oscillator–amplifier system. The laser system generates 9.0 W of 355-nm mode-locked radiation with a pulse duration of 7.5 ps and a repetition rate of 84 MHz. The LBO OPO, synchronously pumped by the 355-nm pulses, generates a signal wave tunable in the blue spectral range 457–479 nm. With a power of up to 5.0 W at 462 nm and 1.7 W at 1535 nm the conversion efficiency is 74%. The OPO is characterized experimentally by measuring the output power (and its dependence on the pump power, the transmission of the output coupler and the resonator length) and the pulse properties (such as pulse duration and spectral width). Also the beam quality of the resonant and nonresonant waves is investigated. The measured results are compared with the predictions of a numerical analysis for Gaussian laser and OPO beams. In addition to the blue-signal output visible-red 629-nm radiation is generated by sum-frequency mixing of the 1.535-μm infrared idler wave with the residual 1.064-μm laser radiation. A power of 1.25 W of 1.535-μm idler radiation and 5.7 W of 1.064-μm laser light generated a red 629-nm output power of 2.25 W. Received: 2 February 2000 / Revised version: 28 July 2000 / Published online: 22 November 2000     

Generation of tunable coherent VUV radiation by anti-Stokes Raman scattering of excimer-pumped dye laser radiation

A straightforward method of generating tunable coherent VUV radiation is described. Radiation down to 1362 Å was produced by Raman shifting the output of a commercially produced, excimer-pumped dye laser system. It is shown that generation of VUV radiation at 1640 Å is more efficient using the 8th anti-Stokes line from a UV dye than by using the 10th anti-Stokes line from a visible dye which had twice the output power.     

Optical Generation of mm-Wave Signal Through Optoelectronic Phase-Locked Loop

In this paper, we propose a scheme for the generation of low phase noise tunable mm-wave signal by beating two lightwaves in a photodiode. These two lightwaves are made phase coherent by an optoelectronic phase locked loop.Calculated mm-wave power at a frequency of 60 GHz is found to be -4 dBm.     

All-solid-state cw mode-locked picosecond KTiOAsO4 (KTA) optical parametric oscillator

4 (KTA) optical parametric oscillator (OPO) synchronously pumped by a cw diode-pumped mode-locked Nd:YVO₄ oscillator–amplifier system. The laser system (pumped by 84 W of cw 808-nm diode radiation) generates 7-ps-long pulses at 1.064 μm with a repetition rate of 83.4 MHz and an average power of 29 W. The OPO, synchronously pumped by the 1.064-μm laser pulses, consists of a 15-mm-long KTA crystal (cut for type II noncritical phase-matching) in a folded signal resonant linear resonator. The average powers of the 1.54-μm signal radiation and the 3.47-μm idler radiation are 14.6 W and 6.4 W, respectively. The total OPO output of 21 W corresponds to an internal efficiency of 75%. The experimental investigations include measurements of the OPO output power (and its dependence on the pump power, the transmission of the output coupler, and the resonator length) and of the pulse properties (such as pulse duration and spectral width). The measured results are in good agreement with the predictions of a numerical analysis based on a split-step Fourier method. Received: 4 May 1998     

增益饱和对光学差频产生太赫兹辐射的功率和稳定性的影响

数值模拟并分析了以GaSe晶体为例对光学差频产生太赫兹（THz）波的特性.结果表明：当THz波长为227.5 μm,晶体长度为26.3 mm时,产生THz波功率达到增益饱和,在增益饱和点输出最高峰值功率可以达到945 W.由于晶体吸收的影响,THz波的增益饱和区是输出功率的非稳定区,而THz波的输出稳定区位于增益饱和区之后,在稳定区的THz波稳定性取决于抽运光的稳定性.当THz波波长为227.5 μm时,达到稳定区所需晶体长度为37.9 mm,此时THz波输出峰值功率可以达到735 W. 关键词： 光学差频 太赫兹辐射 稳定性     

The transmission performance degradation of the optical millimeter-wave signals by fiber chromatic dispersion

The influence of the fiber chromatic dispersion on double sideband (DSB), optical carrier suppression (OCS), and single sideband (SSB) optical mm-wave signals is investigated based on the Taylor expansion of the propagation constant and is verified by simulation. According to our theoretical results, the fading effect suppresses the signal power of the DSB optical mm-wave periodically in a cosine-like pattern, and it can be described by the zero-order Taylor expansion of the propagation constant. For the optical mm-wave with the signal modulated on two or more tones, the bit pulses of the mm-wave signal are distorted by the dispersion-inducing bit walk-off effect between tones, which is expressed by the first-order Taylor expansion of the propagation constant. Moreover, as the signal rate and the transmission distance are increased further, higher-order Taylor expansion of the propagation constant still degrades the optical mm-wave signal even if both the fading effect and the bit walk-off effect are eliminated completely. The distortion of the signal pulses of SSB optical mm-wave is derived based on the second-order Taylor expansion of the propagation constant. This degradation is verified by the simulation with the eye diagram evolution of the SSB optical mm-wave signal.     

1 W of blue 465-nm radiation generated by frequency doubling of the output of a high-power diode laser in critically phase-matched LiB3O5

Blue 465-nm radiation is generated by frequency doubling of the output of an InGaAs diode-laser oscillator-amplifier system in critically phase-matched LiB(3)O(5) (LBO). The diode-laser system emitted 4 W of single-frequency 930-nm radiation in a near-diffraction-limited beam (M(2)<1.2) . The laser power is enhanced to values of up to 150 W in a resonant external ring cavity. The LBO crystal is placed at a resonator internal focus. The frequency doubling in the LBO crystal generates blue radiation at 465 nm with a power of 1 W. The spectral width of the blue radiation is less than 3 MHz, and the value of the M(2) beam parameter is less than 1.2.     

High-power continuous wave green beam generation by use of simple linear cavity with side-pumped module

High-power continuous wave green radiation has been generated by means of type-II phase-matched frequency doubling in a KTP crystal located in a simple linear cavity incorporating a diode side-pumped Nd:YAG laser module. The cavity was designed to make the fundamental beam radius at the KTP crystal smaller than that at the gain medium, as is required for obtaining large mode volume in Nd:YAG crystal and realizing efficient CW intracavity frequency doubling. Output power of 51.2 W is obtained in the experiment with a diode-to-green optical conversion efficiency of 10.3%. The M²-parameters of the laser are measured at different output powers. For the output power of about 47 W, the power fluctuation is measured less than 1%. The experimental results show that the continuous wave green laser system using this simple linear cavity offers good laser performance and output stability.     

Practical mm-Wave pHEMT Frequency Multiplier

Details on a broadband MMIC frequency doubler targeting the MVDS market are presented. The design evolution from an individual pHEMT device to the complete practical doubler realisation is discussed. The doubler MMIC, which has been fabricated using the GMMT H40 GaAs process, has been evaluated in a customised package. An output power of +10 dBm at 40 GHz has been achieved with an associated conversion gain of 1.5 dB. The measured and predicted performance responses are compared. This chip is ideally suited to use in a number of emerging mm-wave applications.     

立式集热板太阳能热气流电站系统研究

设计了一种立式集热板式太阳能热气流电站,分析了该系统的最大输出功率及能量转换率。数学模型考虑了系统尺寸、太阳辐射及环境条件对系统最大输出功率的影响。结果表明系统最大输出功率不仅是烟囱高度的函数,同时与太阳辐射及环境参数有很大关系。受结构限制,在太阳辐射强度为1000 W/m~2、烟囱高度为100m时,本系统能量转换率约为0.2%,在设计上可考虑采用多条集热式烟囱通道并联方式来增加集热面积,以达到提高系统最大输出功率的目的。     

太赫兹大气传输特性实验研究

太赫兹在高速率通信、高分辨力雷达等方面具有广阔的应用前景,而对太赫兹辐射的大气传输特性及其规律进行系统的理论与实验研究则是发展利用该频谱资源的基础条件。对大气作用于太赫兹频段电磁辐射的吸收衰减进行了实验测试研究。通过双光路的差分系统设计,尽可能地减小太赫兹辐射源输出功率不稳定性所产生的系统误差,完成大气模拟环境下太赫兹波段多个频点传输的功率变化测定,以探索大气环境对不同频段THz波衰减的规律性;同时,建立太赫兹大气传输特性动态数据库对海量大气环境数据进行有效地分析,为实验数据处理及理论研究提供支持。收稿日期:; 修订日期:     

基于透射型体布拉格光栅的两通道2.5kW光谱组束输出

体光栅光谱组束是获得高功率激光输出的一种有效途径.在有限的可用带宽内,光谱通道间隔影响着组束光束数目以及最终的高功率组束输出.采用耦合波理论,建立了一个两通道高功率光谱组束模型.通过优化体光栅光谱通道间隔,可放宽对组束子束线宽和功率的限制,组束功率可大幅提升而光谱密度并无显著下降.基于此,实验上获得了2.5 kW组束输出,绝对效率超过85%,通道间隔5 nm,光谱密度为0.51kW/nm.组束功率1 kW时,组束输出能保持好的光束质量;组束功率1.5kW时光束质量恶化较明显,通过分析发现,组束光束质量的恶化主要受限于体光栅的色散及高功率下体光栅复杂的热畸变.     

Full-duplex radio-over-fiber system based on a modified single-side band modulation

A full-duplex radio-over-fiber system based on a modified single-sideband using external modulator is proposed and demonstrated. At the central station, a CW lightwave is intensity-modulated by a RF signal to generate a DSB signal. After the central carrier and the two first-order sidebands are separated by a FBG, the central carrier is modulated with a baseband data at 2.5 Gbit/s. Then, it is recombined with the un-modulated first-order sidebands to generate optical millimeter-wave by an optical coupler with a certain coupling coefficient and transmitted to the base station over single-mode fiber. The central carrier and one of the first-order sidebands are beaten to generate the mm-wave when they are detected by an optical receiver. Another first sideband is reused as carrier for uplink connection. The dispersion performance of the generated mm-wave is theoretically analyzed; one can see that the effect of dispersion and requirement of the optical power are reduced. The PIN-PD can avoid working in a high-DC saturation range which may distort the RF components and depress the responsibility of the detector. The stimulant results show that the system can reduce the effect of dispersion effectively, and immune the fading effect and the walking-off signals. It is suitable for a long distance transmission.     

行波管放大器的非线性混沌特性

以一组非线性方程为基础,从混沌动力学角度,通过计算电子的相空间轨道和辐射场的时空分布图谱,简要分析了行波管放大器的时空混沌特性,计算了行波管输出功率的演化。计算结果表明:行波管放大器辐射场与电子束是一个非线性相互作用的耗散系统,其参数影响整个系统的行为演化,当电流和失谐量等参数变化并超过一定阈值时,系统出现时空混沌特性,输出具有连续的宽频谱性。     

高温超导双晶约瑟夫森结阵列毫米波相干辐射

研究了嵌入Fabry-Perot谐振腔的高温超导双晶约瑟夫森结阵列毫米波相干辐射的实验结果.相干辐射是通过约瑟夫森结阵列与基片(作为一个介质谐振器)和Fabry-Perot(FP)谐振器的共同作用实现的.由166个高温超导双晶约瑟夫森结串联阵列在77 K温度下产生的相干辐射,辐射峰的中心频率为75.84 GHz,功率大约为10 pW. 关键词： 高温超导薄膜 Fabry-Perot谐振腔 约瑟夫森结 毫米波辐射