Optical 3R regeneration of 40 Gbit/s degraded data signals

A 40 Gbit/s optical 3R regenerator is proposed and demonstrated. The 3R regenerator consists of a dual-ring injection mode-locked fiber ring laser as the clock recovery module and an electroabsorption modulator (EAM) as the decision gate. The clock recovery module extracts the optical short pulse clock with low timing jitter from degraded 40 Gbit/s optical data streams, while the decision gate restores their signal quality. A numerical model describing the cross-absorption modulation effect in a bulk EAM is developed to explore the operating conditions, such as bias voltage, pump signal power. The timing jitter tolerance for the EAM optical gate is also investigated. Significantly improvement of BER is obtained from 40 Gbit/s RZ signals which are degraded by polarization mode dispersion or chromatic dispersion.     

Multi-wavelength conversion at 10 Gb/s using cross-phase modulation in highly nonlinear fiber

In this paper we demonstrate a technique of signal wavelength conversion via cross-phase modulation (XPM)-induced nonlinear coupling among a 10 GHz return-to-zero (RZ) signal and a continuous wave (CW) carrier co-propagating in dispersion-shifted (DS) highly nonlinear fiber (HNLF). The wavelength conversion bandwidth up to ±20 nm was achieved experimentally and potential extension was verified by numerical simulations. The principle can easily be extended to 40 Gb/s and used as polarization insensitive all-optical wavelength converter.     

10 GHz passive harmonic mode-locking in Er-Yb double-clad fiber laser

In this paper we report passive harmonic mode-locking of an Erbium/Ytterbium-doped double-clad fiber laser with repetition rates up to 10 GHz. The modes synchronization was obtained using Nonlinear Polarization Rotation mechanism. The stable operation at 634th harmonic of the fundamental (15.8 MHz) repetition frequency was achieved. Soliton pulses with the duration of less than 900 fs and 300 mW average output power were obtained.     

10 and 20 Gb/s all-optical RZ to NRZ modulation format and wavelength converter based on nonlinear optical loop mirror

We present experimental and theoretical results on all-optical 10 and 20 Gb/s RZ to NRZ modulation format and wavelength converter based on a nonlinear optical loop mirror (NOLM). A vector model of converter was developed and the shape of converted pulses was found analytically for particular choice of polarization states. In the experiment, non-zero dispersion shifted fiber with a length 1200 m was used as a nonlinear medium. Pulses from a 10 GHz mode-locked semiconductor laser diode were modulated to form pseudorandom RZ signal and eventually time division multiplexed to 20 Gb/s. RZ pulses were subsequently converted to NRZ signal. The performance of the converter was evaluated experimentally using the data communication analyzer and bit error ratio tester.     

Amplified feedback DFB laser for 40 Gb/s all-optical clock recovery

A monolithic integrated amplified feedback semiconductor laser (AFL) was fabricated based on quantum well intermixing (QWI) technique. The AFL works as a self-pulsation laser. It consists of a gain-coupled multiple quantum well distribute feedback (DFB) laser diode (LD) section, a passive phase section and an amplified feedback section. The free-running repetition frequency of the AFL can be tuned from 32 GHz to 51 GHz via controlling the feedback strength. All-optical 40 Gb/s clock recovery was experimentally demonstrated using the AFL with a low timing jitter.     

All-optical clock recovery of 20 Gbit/s NRZ-DPSK signals using polarization-maintaining fiber loop mirror filter and semiconductor optical amplifier fiber ring laser

All-optical clock recovery (CR) from 20 Gbit/s nonreturn-to-zero differential phase-shift-keying (NRZ-DPSK) signals are demonstrated experimentally by using a polarization-maintaining fiber loop mirror filter (PMF-LMF) and a semiconductor optical amplifier (SOA) fiber ring laser. Only by adjusting polarization controller (PC), NRZ-DPSK signals were conveniently and fast converted to pseudo return-to-zero (PRZ) signal via PMF-LMF. Then the PRZ signals are injected into the SOA fiber laser for CR. The recovered clock signals is with the extinction ratio (ER) of 10 dB and the root-mean-square (RMS) timing jitter of 750 fs in 2³¹ − 1 long pseudorandom binary sequence (PRBS) NRZ-DPSK signals measurement. Moreover, the broad wavelength tunability of recovered clock stemmed from the use of SOAs as modulator and the gain medium are shown too.     

Experimental investigation of harmonic and subharmonic synchronization of 40 GHz mode-locked quantum-dash laser diodes

Synchronization of a 40 GHz quantum-dash mode-locked (ML) Fabry-Perot laser diode with optically injected pulse streams is experimentally studied. Injected signals consist of nonmodulated and modulated trains of 1.6 ps pulses at various repetition rates, ranging from 10 to 160 GHz and 10 to 160 Gbps, respectively. Subharmonic, fundamental, and harmonic synchronization of the ML laser allows retrieval of stable 40 GHz clock pulses featuring a width of 1.8 ps. Frequency components at 10 and 20 GHz do not create any amplitude modulation on the recovered 40 GHz clock pulses when injecting signals at 10 and 20 GHz/Gbps. In addition, external synchronization of the laser with pulse streams at 80 and 160 GHz/Gbps is sustained despite the absence of significant components at or below 40 GHz.     

Experimental demonstration on 40 Gbit/s all-optical multicasting logic XOR gate for NRZ-DPSK signals using four-wave mixing in highly nonlinear fiber

We propose and demonstrate all-optical multicasting logic XOR gate for non-return-to-zero differential phase-shift keying (NRZ-DPSK) signals by using non-degenerate four-wave mixing (FWM) in a highly nonlinear fiber (HNLF). Theoretical analysis regarding the operation principle of NRZ-DPSK logic XOR gate is clearly described by deriving an analytical solution under the non-depletion approximation. The NRZ-DPSK logic XOR operation is attributed to the linear relationship of complex amplitudes between converted idlers and input NRZ-DPSK signals. By using three non-degenerate FWM processes in an HNLF, 40 Gbit/s all-optical multicasting logic XOR gate for NRZ-DPSK signals are successfully demonstrated in the experiment.     

Medium power single-mode single-wavelength fiber laser

Medium-power, single-mode, single-wavelength fiber laser working at room temperature using a polarization-maintaining erbium-ytterbium co-doped fiber as the gain medium, and an un-pumped elliptical core erbium-doped fiber as a saturable absorber to reduce linewidth and mode hopping of the lasing wavelength is reported. The effects of length, erbium ion concentration, and polarization-maintaining property of the saturable absorber were explored. The output power of the laser was more than 100 mW and the lasing line was stable for more than 3 h with an intensity fluctuation of less than 0.2 dB. The laser linewidth (FWHM = Full width at half maximum) was 7.5 MHz and the signal to noise ratio was more than 50 dB. The output of the laser was measured using an optical spectrum analyzer (OSA) of resolution 1.25 GHz and a scanning Fabry-Perot spectrum analyzer (SFPSA) of resolution 6.7 MHz.     

Ultra-fast 160:10 Gbit/s time demultiplexing by four wave mixing in 1 m-long B2O3-based fiber

One meter-long spool of bismuth oxide-based fiber, with nonlinear coefficient of 1250 W⁻¹ km⁻¹, is used to realize an optical 160-to-10 Gbit/s demultiplexer based on four wave mixing. Bit-Error-Rate measurements demonstrate a demultiplexing penalty lower than 2 dB confirming the suitability of bismuth oxide-based fiber for 160 Gbit/s all-optical processing.     

Transmission performance of 20 × 10 Gb/s WDM signals using cascaded optimized SOAs with OOK and DPSK modulation formats

We investigated 20 channels at 10 Gb/s wavelength division multiplexing (WDM) transmission over 1190 km single mode fiber and dispersion compensating fiber using cascaded inline semiconductor optical amplifier at a span of 70 km for RZ-DPSK (return zero differential phase-shift keying) modulation format by using same channel spacing, i.e. 100 GHz. We show for RZ-OOK (return zero on-off keying) format a transmission distance of up to 1050 km with Q factor more than 15 dB, without any power drops. We developed the SOA model for inline amplifier having minimum cross-talks and ASE (amplified spontaneous emission) noise power with sufficient gain. At optimal bias current of 400 mA, a high constant gain of 36.5 dB is obtained up to a saturation power of 21.36 mW. So reduction of cross-talk and distortion is possible by decreasing the bias current at appropriate amplification factor.The DPSK modulation format has less cross-talk as compared to OOK format for nonlinearities and saturation case. The impact of optical power received and Q factor at different distance for both RZ-OOK and RZ-DPSK modulation format has been illustrated. We have shown the optical spectrum and clear Eye diagram at the transmission distance of 1190 km in RZ-DPSK system and 1050 km in RZ-OOK systems.The bit error rate (BER) for all channels observed is less than 10⁻¹⁰ up to gain saturation for both DPSK and OOK systems. Finally, we investigated that the transmission distance decreases with a decrease in channel spacing of up to 20 GHz.     

Tunable 19 × 10 GHz L-band FP-SOA based multi-wavelength mode-locked fiber laser

We present a multi-wavelength mode-locked fiber ring laser incorporating a semiconductor optical amplifier (SOA) and a Fabry-Perot semiconductor optical amplifier (FP-SOA). Because the gain of the SOA is depleted by an external injection optical signal, the SOA acts as a loss modulator. The FP-SOA serves as a tunable comb filter. The presented laser source can generate 19 synchronized wavelength channels with the extinction ratio of about 21 dB, each mode-locked at 10 GHz, and mode-locked pulse width is about 40 ps. Oscillation wavelengths band can be tuned by adjusting the bias current of the SOA, and wavelength spacing also can be changed by using a tunable optical delay line (ODL) or a temperature controller. The polarization-insensitive devices ensure that the output power is rather stable. This fiber laser has potential applications in longer waveband (L-band) within the low-attenuation window.     

All-optical clock recovery using a ridge width varied two-section partly gain-coupled DFB self-pulsation laser

A 1.55 μm InGaAsP-InP partly gain-coupled two-section DFB self-pulsation laser (SPL) with a varied ridge width has been fabricated. The laser produces self-pulsations with a frequency tuning range of more than 135 GHz. All-optical clock recovery from 40 Gb/s degraded data streams has been demonstrated. Successful lockings of the device at frequencies of 30 GHz, 40 GHz, 50 GHz, and 60 GHz to a 10 GHz sidemode injection are also conducted, which demonstrates the capability of the device for all-optical clock recovery at different frequencies. This flexibility of the device is highly desired for practical uses.     

Numerical analysis and system optimization for 100 Gbit/s carrier Ethernet serial modulation formats

The performance of various modulation schemes for 100 Gbit/s single-channel serial transmission is investigated by means of numerical simulations. Different ASK and PSK modulation formats are compared in terms of total system reach for a 10⁻⁹ BER requirement. RZ-DQPSK format with a 1920 km reach, without FEC and without the support of additional Raman amplification, outperforms all the other schemes including 10 × 10 Gbit/s NRZ DWDM inverse multiplexing.     

High-resolution spectroscopy using interleaved 100 GHz optical frequency comb scanned by phase modulator

A high-resolution spectroscopy technique is proposed with an optical phase modulator combined with an interleaved optical frequency comb. The optical phase modulator and a frequency-locked laser light guarantee a spectral resolution less than 1 MHz on an absolute frequency axis. A wide measurement frequency range was realized using a 25 GHz optical frequency comb lying over a 4 THz frequency region. An extraction of single tooth intensity from the comb was realized by a heterodyne technique with a frequency-tunable laser used as a local oscillator. Also, the 25 GHz optical frequency comb was interleaved to generate four 100-GHz combs for removing the crosstalk from the 25 GHz neighboring sidebands in the teeth. This proposed spectroscopy technique was experimentally demonstrated with a resonator of less than 1 MHz linewidth and a H¹³C¹⁴N gas cell. Thus, a measurement frequency range higher than 4 THz (1530 nm-1560 nm) was confirmed with an effective spectral resolution 100 kHz order. In addition, the characteristics of the proposed system were compared with those of the previous system with a single-sideband (SSB) optical modulator.     

A novel approach to all-optical wavelength conversion by utilizing a reflective semiconductor optical amplifier in a co-propagation scheme

Nonlinear optical gain modulation in an InGaAsP/InP bulk reflective semiconductor optical amplifier (RSOA) is studied. The differences of the optical properties between RSOAs and conventional SOAs are initially investigated. All-optical wavelength conversion based on nonlinear gain modulation in RSOAs is demonstrated at a bit rate of 2.488 Gbit/s. It is shown that a bit-error-rate of <10⁻⁹ can be achieved and an extinction ratio of >9 dB can be obtained at a bit rate of 2.488 Gbit/s with a 2³¹-1 non-return-to-zero (NRZ) pseudorandom bit sequence (PRBS). In comparison with conventional SOAs, wavelength conversion by RSOAs shows much improved performances in high-speed all-optical wavelength conversions.     

Frequency modulated and polarization maintaining fiber laser with narrow linewidth

A novel configuration of fiber laser with frequency modulation is presented. Frequency modulation, stable polarization state and narrow linewidth are realized by using the waveguide phase modulator, polarization maintaining devices and saturable absorber. It is shown that the laser output reaches 23 mW, linewidth is less than 1 kHz, polarization extinction ratio is higher than 20 dB and maximum value of frequency deviation can reach 7.5 MHz.     

Design and optimization of frequency tunable semiconductor laser used in resonator integrated optic gyro

Frequency tunable semiconductor laser has potential applications in resonator integrated optic gyro (RIOG) for its small size and easy to be integrated. An alternative construction of frequency tunable semiconductor laser with planar waveguide external cavity is proposed in this paper. The frequency tuning section, which is placed between the active section and Bragg grating section, is designed to be one part of the waveguide external cavity. The slab etched grating, based on the silicon-on-isolator ridge waveguide, is adopted to narrow the width of reflectivity spectrum. After the theoretical analysis and simulations, the frequency modulation coefficient of 2.1 MHz/mA is obtained, and the power change is less than 3.6 × 10⁻⁴ dB/1.6 GHz. The proposed configuration combines the advantages of wavelength tunable laser and external cavity laser, and it can realize precision frequency tuning, ignored power fluctuation and narrow linewidth, which contribute much to RIOG.     

Tunable, μs-pulsed ytterbium fiber laser system with a linewidth below 2.7 GHz

We report on a widely tunable, pulsed laser system with narrow spectral linewidth based on a continuous wave ytterbium fiber oscillator, a pulse shaper and a power amplifier stage. The system is tunable from 1055 nm to 1085 nm and provides a maximum pulse energy of 155 μJ with a pulse duration of 1-5 μs. The linewidth is less than 2.7 GHz over the whole tuning range.     

40 Gb/s all-optical logic NOR and OR gates using a semiconductor optical amplifier: Experimental demonstration and theoretical analysis

We experimentally and theoretically demonstrate 40 Gb/s all-optical logic NOR and OR gates based on a semiconductor optical amplifier (SOA) and a blue shifted optical bandpass filter (OBF). Two kinds of data formats are discussed, namely return-to-zero (RZ) format and nonreturn-to-zero (NRZ) format. The logic NOR and OR functions of RZ format are realized at the OBF detuning of −0.22 nm and −0.44 nm, respectively. The logic NOR function of NRZ format is realized at the OBF detuning of −0.24 nm. The simulation is in good agreement with the experimental results when the linewidth enhancement factor is 5.5. The simulation also shows that the SOA with large linewidth enhancement factor is preferred to achieve NOR and OR functions with good performance. The input data signal is of good pulsewidth-tolerance for NOR function, whereas not for OR function. The high Q factor could be obtained at narrow pulses injection.