A 9.5-W 82-MHz-repetition-rate picosecond optical parametric generator with cw diode laser injection seeding

We report on an injection-seeded 9.5-W 82-MHz-repetition-rate picosecond optical parametric generator (OPG) based on a 55 mm long crystal of periodically poled lithium niobate (PPLN) with a quasi-phase-matching (QPM) grating period of 29.75 μm. The OPG is excited by a continuously diode pumped mode-locked picosecond Nd:YVO₄ oscillator-amplifier system. The laser system generates 7 ps pulses with a repetition rate of 82.3 MHz and an average power of 24 W. Without injection-seeding the total average output power of the OPG is 8.9 W, which corresponds to an internal conversion efficiency of 50%. The wavelengths of the signal and idler waves were tuned in the range 1.57–1.64 μm and 3.03–3.3 μm, respectively, by changing the crystal temperature from 150 °C to 250 °C. Injection seeding of the OPG at 1.58 μm with 4 mW of single frequency continuous-wave radiation of a distributed-feedback (DFB) diode laser increases the OPG output to 9.5 W (53% conversion efficiency). The injection seeding increases the pulse duration and reduces the spectral bandwidth. When pumped by 10 W of 1.06 μm laser radiation, the duration of the signal pulses increased from 3.6 ps to 5.5 ps while the spectral bandwidth is reduced from 4.5 nm to 0.85 nm. Seeding thus improved the time-bandwidth product from 1.98 to a value of 0.56, much closer to the Fourier limit. Received: 29 April 2002 / Published online: 8 August 2002     

High-peak power multi-wavelength picosecond pulses generated from a BaWO4 Raman-seeded optical parametric amplifier

We report the generation of high-peak power multi-wavelength picosecond laser pulses using optical parametric amplification (OPA) in BBO seeded with pulses generated in a 5-mm length BaWO₄ crystal by stimulated Raman scattering of 18-ps laser pulses at 532 nm. The maximum output energy of the amplified first-Stokes component at 559.7 nm was about 1.76 mJ. The corresponding maximum peak power, pulse duration and spectral line width were measured to be 117.3 MW, 15 ps and 18.0 cm⁻¹, respectively. The multi-wavelength picosecond laser pulses were in the visible and near infrared ranges. Using this Raman-seeded OPA technique, the beam quality of the stimulated Raman scattering pulses can be improved.     

Efficient multi-frequency generation of ultrashort light pulses using stimulated Raman scattering and optical parametric amplification

Optical parametric amplification of multi-frequency seed pulses generated in a mixture of compressed hydrogen and methane by stimulated Raman scattering of 1 ps, 1 kHz laser pulses at 395.8 nm has been studied. Efficient generation of spectrally narrow ultrashort pulses with a spatial distribution close to the Gaussian profile of the pump beam was obtained in the visible and near infrared ranges.     

Detection of scattered light pulses at femto-Joule level by using a picosecond BBO optical parametric amplifier

We report a technique for detecting weak scattered light pulses based on a 532 nm pumped picosecond β-barium-borate collinear optical parametric amplifier. The measured maximum slope gain factor of the amplifier was found to be around 10⁷, and the energy detection limit was of the order of fJ/pulse for the signal of 730 nm and the idler of 1.5 μm at a pumping intensity of 2.83 GW/cm². The linearity of the gain for this amplifier was found to be excellent for a seeding level of lower than 420 fJ per pulse. The maximum gains and the energy detection limits for the scattered light pulses from various scattering targets were found to be poorer than that from the reflective mirror, owing to the degraded beam quality and the depolarization of the scattered light. A reduction of the maximum gain for the scattered light with the increase of the angle of incidence, which causes pulse broadening and reduces the photon flux of the signal, was investigated. The feasibility of detecting weak scattered light in the infrared by using idler-to-signal frequency up-conversion was also demonstrated, in which the infrared seeder located in the idler branch of the amplifier was injected as the seeding beam and was then parametrically up-converted into the visible signal branch, with an even higher gain.     

Sum and difference frequency generation of white light continuum with the ps pulses of Nd:YAG laser in a thick BBO crystal

The white light continuum (WLC) generated in water/D₂O mixture by pumping with the fundamental of ps Nd⁺³:YAG laser has been used as a variable frequency source for the sum frequency generation as well as for its amplification. 35 ps long pulses with 8 mJ energy at 1064 nm were mixed collinearly with the WLC generated by the same laser beam in a 20 mm thick BBO crystal. The obtained tunable output has been identified as the sum frequency between the fundamental and a portion of the WLC with the required phase matching. Theoretical simulations are also given along with a few initial experiments to use this combination for the difference frequency generation (optical parametric amplification) under non-collinear geometry.     

Spatial-temporal frequency band of optical parametric amplifier

The spatial-temporal frequency band of optical parametric amplifier for collinear as well as for noncollinear phase-matching is analyzed taking into account angular dispersion of amplified pulsed beam. The simple formulae are derived which make possible determination of the largest frequency bands of parametric amplifiers in noncollinear geometry. It has been demonstrated that a shape of the spatial-temporal frequency band of optical parametric amplifier essentially depends on pump and signal wavelengths, and certain angular dispersion as well as proper beamwidth of signal pulse enable amplification of ultrashort pulses with duration of a few femtoseconds.     

AOPDF-shaped optical parametric amplifier output in the visible

Time shaping of ultra-short visible pulses has been performed using a specially designed acousto-optic programmable dispersive filter of 50% efficiency at the output of a two-stage non-collinear optical parametric amplifier. The set-up is compact and reliable. It provides a tunable shaped source in the visible with unique features: a 4-ps shaping window with preserved tunability over 500–650 nm, and pulses as short as 30 fs. Several-μJ output energy is easily obtained.     

Compact high gain double-pass optical parametric chirped pulse amplifier

A novel double-pass noncollinear optical parametric chirped pulse amplifier based on an Yb³⁺-doped passively mode-locked fiber laser has been demonstrated in this paper. The signal was double-pass amplified in a single nonlinear crystal by a long pump pulse, and the signal and pump pulses of each pass were completely phase matched in the plane of the maximum effective nonlinearity. Net saturated gain of 2×10⁶ was achieved and the superfluorescence was suppressed by increasing the overlap time between the signal and pump pulses.     

Harmonic repetition-rate femtosecond optical parametric oscillator

We report on a femtosecond optical parametric oscillator (OPO) with a repetition rate of 1 GHz, which is 12 times that of the pump laser used. We also introduce a novel method for operating an OPO with a high harmonic repetition rate which is not determined by the cavity length of the OPO, but rather the cavity length difference between the OPO and its pump laser. Operation of an OPO at 4-times the harmonic repetition rate has been carried out to show the feasibility of this method. The new approach paves the way for constructing a femtosecond OPO working at repetition rates of 10 GHz, or higher, when the pump laser used has a relatively low repetition rate. Received: 26 October 2001 / Revised version: 11 Januar 2002 / Published online: 14 March 2002     

Phase-sensitive multimodal optical parametric amplifier for beam angle amplification

The single-mode phase-sensitive parametric amplifier has been proposed as an approximation to an ideal quantum phase amplifier. We demonstrate numerically that a real, multimode parametric amplifier operated in the spatial domain, and realized by the use of three-wave mixing in nonlinear media, behaves similar to a single-mode quantum phase amplifier, but exhibits smaller phase gain. Constraints for operation in this regime are found to be consistent with small departures of phase from the ideal deamplification condition.     

Influence of gas circulation on stimulated Raman scattering and amplification of ultrashort laser pulses in methane

Applying gas recirculation in a high pressure cell, laser pulses of 1 ps at 400 nm and with a repetition rate of 1 kHz were frequency shifted by stimulated Raman scattering and amplification in methane gas at high pressure. We studied the influence of gas recirculation on the conversion efficiencies into the Stokes and anti-Stokes components as well as on their spatial distributions and spectral shapes using generator and generator-amplifier arrangements. For high pump energies, recirculation in the generator cell decreases conversion efficiency into the first Stokes component whereas it increases conversion into higher Stokes and anti-Stokes components. It results in a significantly improved spatial characteristics of the frequency-shifted radiation, however, is accompanied by a substantial spectral broadening. Using gas recirculation in the generator-amplifier arrangement we achieved a conversion efficiency into the first Stokes component of about 50% with highly improved spatial and spectral characteristics.     

Synchronously pumped femtosecond optical parametric oscillator of congruent and stoichiometric MgO-doped periodically poled lithium niobate

A synchronously pumped femtosecond optical parametric oscillator based on congruent MgO-doped periodically poled lithium niobate (c-MgO:PPLN) is reported. The system, operating at room temperature, was pumped by a mode-locked Ti:sapphire laser. The wavelengths of the signal and idler waves were tuned from 870 nm to 1.54 μm and 1.58 to 5.67 μm, respectively, by changing the pump wavelength, the grating period or the cavity length. Pumped by 1.1 W of 755 nm laser radiation, the OPO generated 310 mW of 1080 nm radiation. This signal output corresponds to a total conversion efficiency of 50%. Without dispersion compensation the OPO generated phase-modulated signal pulses of 200 fs duration. Besides the OPO of c-MgO:PPLN, an OPO of stoichiometric (s) MgO:PPLN was investigated. Because of the reduced sensitivity to photorefractive damage, both crystals allowed efficient OPO operation at room temperature. Received: 19 August 2002 / Revised version: 11 December 2002 / Published online: 19 March 2003 RID="*" ID="*"Corresponding author. Fax: +49-631/205-3906, E-mail: andres@physik.uni-kl.de     

Low-threshold high-dynamic-range optical limiter for ultra-short laser pulses

We demonstrate an optical limiter for ultra-short (∼100-fs) laser pulses. The device has a dynamic range (= damage energy/onset-of-limiting energy) of more than 10000 and an onset-of-limiting energy of only ∼10 nJ. The output-pulse energy is kept below 1.3 μJ. The limiting mechanism is based on two-photon absorption and refractive nonlinearities in a 20-mm piece of ZnSe. We discuss the importance of the different nonlinearities, damage issues, and guidelines for the construction of the device. Received: 20 December 2001 / Revised version: 25 March 2002 / Published online: 8 May 2002     

Tunable, high-power, narrow-band picosecond IR radiation by optical parametric amplification in KTP

We report on an optical parametric amplifier (OPA) based on two potassium titanyl phosphate (KTP) crystals in a walk-off compensating geometry. An Nd:YLF regenerative amplifier at a 1-kHz repetition rate serves as the pump source. The seed beam is delivered by a synchronously pumped frequency-stabilized optical parametric oscillator (OPO) based on periodically poled lithium niobate (PPLN). At pump intensities of about 7 GW/cm² large amplification factors of more than 10⁴ were achieved, resulting in pulse energies of more than 450 μJ and 350 μJ for the signal and idler pulses, respectively, at a 1-kHz repetition rate. In the saturation regime the time–bandwidth product increases from two to three times the Fourier limit, with a pulse duration of 105 ps and a bandwidth of 12.7 GHz at the highest intensities employed. Received: 2 November 2001 / Published online: 14 March 2002     

Optimization of optical parametric chirped pulse amplification with different pump wavelengths

Optical parametric chirped pulse amplification with different pump wavelengths was investigated using LBO crystal, at signal central wavelength of 800 nm. According to our theoretical simulation, when pump wavelength is 492.5 nm, there is a maximal gain bandwidth of 190 nm centered at 805 nm in optimal noncollinear angle using LBO. Presently, pump wavelength of 492.5 nm can be obtained from second harmonic generation of a Yb:Sr₅(PO₄)₃F laser. The broad gain bandwidth can completely support ∼6 fs with a spectral centre of seed pulse at 800 nm. The deviation from optimal noncollinear angle can be compensated by accurately tuning crystal angle for phase matching. The gain spectrum with pump wavelength of 492.5 nm is much better than those with pump wavelengths of 400, 526.5 and 532 nm, at signal centre of 800 nm.     

High-power picosecond LiB3O5 optical parametric oscillators tunable in the blue spectral range

The paper reports on an experimental investigation and numerical analysis of noncritically and critically phasematched LiB₃O₅ (LBO) optical parametric oscillators (OPOs) synchronously pumped by the third harmonic of a cw diode-pumped mode-locked Nd:YVO₄ oscillator–amplifier system. The laser system generates 9.0 W of 355-nm mode-locked radiation with a pulse duration of 7.5 ps and a repetition rate of 84 MHz. The LBO OPO, synchronously pumped by the 355-nm pulses, generates a signal wave tunable in the blue spectral range 457–479 nm. With a power of up to 5.0 W at 462 nm and 1.7 W at 1535 nm the conversion efficiency is 74%. The OPO is characterized experimentally by measuring the output power (and its dependence on the pump power, the transmission of the output coupler and the resonator length) and the pulse properties (such as pulse duration and spectral width). Also the beam quality of the resonant and nonresonant waves is investigated. The measured results are compared with the predictions of a numerical analysis for Gaussian laser and OPO beams. In addition to the blue-signal output visible-red 629-nm radiation is generated by sum-frequency mixing of the 1.535-μm infrared idler wave with the residual 1.064-μm laser radiation. A power of 1.25 W of 1.535-μm idler radiation and 5.7 W of 1.064-μm laser light generated a red 629-nm output power of 2.25 W. Received: 2 February 2000 / Revised version: 28 July 2000 / Published online: 22 November 2000     

Characterization of ultra-weak fluorescence using picosecond non-collinear optical parametric amplifier

We report a technique for characterization of ultra-weak fluorescence based on a 355-nm pumped picosecond non-collinear optical parametric amplifier (OPA). In the experiment, we effectively reduced the strong super-fluorescence background by using a series of methods. With the picosecond OPA as the pre-amplifier and the gating pulse, the decay of the fluorescence of Rhodamine 6G dye in ethanol was measured and the fluorescence lifetime was found to be about 941 ps. The gain factor of this parametric fluorescence amplifier was measured to be ∼4.2 × 10⁶, while the energy detection limit was ∼160 aJ per pulse within a 15-ps gating pulse.     

Development of a nearly transform-limited, low-repetition-rate, picosecond optical parametric generator

A low-repetition-rate (10-Hz), picosecond (ps) optical parametric generator (OPG) seeded at the idler wavelength with a high-power diode laser is demonstrated. The output of the OPG at ∼566 nm is amplified in dye cells, resulting in signal enhancement by more than three orders of magnitude. The nearly transform-limited beam at ∼566 nm has a pulsewidth of ∼170 ps, with an overall output of ∼2.3 mJ/pulse. The laser is tuned either by tuning the nonlinear crystal or the seed-laser current. The applications of such a simple, compact, high-performance, tunable ps laser system for linear and nonlinear spectroscopies are outlined.     

Widely tunable femtosecond fiber optical parametric oscillator

The phase-matching condition in a fiber is discussed. A balance among the different orders of fiber dispersion can be found to achieve a widely tuning modulation instability gain for pumping around the normal dispersion regime. Three coupled nonlinear wave equations are used to simulate the femtosecond fiber optical parametric oscillator. The numerical results show that, through appropriate choice of dispersion, femtosecond pulses with a 180-nm tunable range can be generated when pump wavelength near a fiber’s zero-dispersion wavelength is tuned only 7 nm. Further tuning is limited by the walk-off between the pump and the signal pulses.     

Competing processes in optical parametric chirped pulse amplification

Optical parametric chirped pulse amplification (OPCPA) has the potential to revolutionise the generation of high power ultrashort optical pulses. In this paper, we present the results of a numerical investigation into processes that potentially compete with OPCPA. Specifically, we examine group velocity dispersion, non-degenerate operation, background noise, pump pulse fluctuations, and compressor error. We also discuss the “local approximation” and show that, in the case of OPCPA, it offers a substantial advantage in computational speed for minimal cost in accuracy. The overall conclusion is that OPCPA is fundamentally robust, and that the processes studied pose a less serious problem than might have been expected.