Injection locked single mode operation of a tea CO2 laser with high energy extraction

Generation of reproducible smooth pulses from longitudinal mode control of a TEA CO₂ laser by signal injection from a cw CO₂ laser is reported and the operating conditions investigated for several new geometries. Applied to unstable resonators, the efficient and spectrally pure, high power output obtains has important application in the area of optical pumping.     

Optimization of three gas compositions in a CO2 laser

Three pressures of gases (CO₂, N₂ and He) added into CO₂ laser tube are optimized for obtaining maximal laser output power by applying a genetic algorithm and solving the CO₂ laser kinetics equations. After the optimization, the laser power is increased by 96% as compared with a non-optimal case.     

AC-chopper application for CW CO2 laser

A microprocessor-based algorithm was developed to control the power supply to a CO₂ laser using an AC-chopper method. This system was connected directly to a CO₂ laser tube without the need for a dc-dc converter or the storage capacitance of a multilevel circuit. The typical CO₂ laser power supply system had a full-bridge series resonant inverter or voltage multiplier. AC-to-AC converter schemes using zero voltage switching (ZVS) can be used efficiently and economically for low and medium power applications.This paper reports the performance characteristics of a symmetrical AC-chopper technology that can maintain the quality of the ac output of a CO₂ laser tube, regardless of the amount of switching loss. The laser was operated to an output power, maximum system efficiency total gas mixture of 37.2 W, 92%, and CO₂:N₂:He=1:9:15, respectively. The laser system, AC-chopper power supply and its operation were examined.     

Design and experimental characterisation of a DC-excited CW/repetitively pulsed sealed off CO2 laser

This paper reports the design procedure and experimental study of a sealed off CO₂ laser. Simple algorithms for threshold and steady state excitation voltage calculation, resonator design and its temperature dependent operation are presented. The sealed off CO₂ laser was operated both in CW and pulsed modes and found stable both thermodynamically and optically. Frequency limits for pulsed operation regarding maximum and minimum output energy ranges are determined. Different aspects of CO₂ laser studied include threshold excitation voltages, temperature dependent efficiency, optical power saturation limitations, pulsed and steady state discharge currents for optimum gases mixture combinations. The laser has successfully been constructed, operated and tested for different applications within the limits of its maximum output power of 14 W.     

Design considerations and scaling laws for high power convective cooled CW CO2 lasers

Various criteria for designing high power convective cooled CO₂ lasers have been discussed. Considering the saturation intensity, optical damage threshold of the optical resonator components and the small-signal gain, the scaling laws for designing high power CW CO₂ lasers have been established. In transverse flow CO₂ lasers having discharge of square cross-section, the discharge lengthL and its widthW for a specific laser powerP (Watt) and gas flow velocityV (cm/s) can be given byL = 1.4 x 10⁴ p ^1/2 V ^-1 cms andW = 0.04P ^1/2 cms. The optimum transmitivity of the output coupler is found to be almost constant (about 60%), independent of the small signal gain and laser power. In fast axial flow CO₂ lasers the gas flow should be divided into several discharge tubes to maintain the flow velocity within sonic limit. The discharge length in this type of laser does not depend explicitly on the laser power, instead it depends on the input power density in the discharge and the gas flow velocity. Various considerations for ensuring better laser beam quality are also discussed.     

An injection-locked single-mode tea CO2 laser for SMM laser pumping

A D₂O laser has been developed for collective Thomson scattering measurements of ion temperature in high temperature plasmas. A pulse duration and a spectral width of a high power D₂O laser has been successfully controlled for this purpose, by using a TEA CO₂ laser injection-locked by an etalon-tuned TEA CO₂ laser as a pump source.     

Design and operation characteristics of a high power transverse flow pulser sustained cw CO2 laser

A transverse flow, transverse discharge cw CO₂ laser in which de discharge is sustained by employing high repetition rate high voltage pulses has been developed. Pulser sustained discharge through electrodes of innovative design provided uniform excitation at electrical input power densities more than 10 W/cc. Laser output power more than 2.5 kW was obtained in a laser gas mixture consisting of 0.5 mbar of CO₂, 16 mbar of N₂ and 38.5 mbar of He. Design details and operational characteristics of this laser are presented.     

Precision Tunable Infrared Source at 10 μM: CO2-Laser/Microwave-Sideband System with an Evenson CO2 Laser and a Cheo Waveguide Modulator

A CO₂-laser/microwave-sideband tunable infrared source system has been newly built at the University of New Brunswick (UNB) in Canada. The system employs a high-resolution CO₂ laser of Evenson design that lases on a wide range of lines including hot and sequence band lines as well as high-J lines of the regular 9.6 and 10.6 m bands. The frequency of the CO₂ laser is stabilized to the Lamb dip in the 4.3 m fluorescence signal in an external CO₂ cell. Microwave (MW) sidebands are generated in a Cheo-type infrared waveguide modulator driven by a synthesized sweeper and a traveling wave tube (TWT) amplifier. The MW sidebands appear on either side of the CO₂ laser line, and are individually separated from the carrier by a tunable Fabry-Perot etalon. The sidebands currently have a typical power of about 1.4 mW and a continuous frequency tuning range of 22 GHz (from ± to ±18 GHz) when 5 W laser power and 15 W microwave power are delivered to the modulator. Details are given on the source construction and measured performance characteristics. Features of the source and its planned applications are discussed.     

Construction of a photon drag detector for evaluating the performance of a CO2 laser amplifier

In this article, the construction of P-type germanium (Ge) photon drag detector which is used to characterize the gain and output powers of a 10 W CO₂ laser and a CO₂ laser amplifier is described. Gain and laser amplifier output power versus laser input power measurements collected at 4.7 mbar and 12.0 mbar amplifier tube pressures are discussed. Moreover, measurements relating the CO₂ laser output power to the laser tube discharge current are provided at 6.9 mbar and 7.3 mbar tube pressures.     

Numerical modeling of a fast-axial-flow CW–CO2 laser

A four-temperature model has been applied on a fast axial flow, longitudinal discharge CO₂ laser. Using Runge–Kutta method, a set of differential equations of the model is numericaly solved. These equations describe the operation of the laser with certain ratio 1:3:6 of the mixture CO₂:N₂: He and average output power of 550 W.The temporal behaviour of the output power and photon density was obtained. The effects of kinetic temperature, coupled mirror reflectivity, gas flow speed, and cavity loss on the output power were studied.Calculated output power was compared with its measured value taken from experiment and a good agreement was observed.     

Operational characteristics and power scaling of a transverse flow transversely excited CW CO<Subscript>2</Subscript> laser

Transverse flow transversely excited (TFTE) CO₂ lasers are easily scalable to multikilowatt level. The laser power can be scaled up by increasing the volumetric gas flow and discharge volume. It was observed in a TFTE CW CO₂ laser having single row of pins as an anode and tubular cathode that the laser power was not increasing when the discharge volume and the gas volumetric flow were increased by increasing the electrode separation keeping the gas flow velocity constant. The discharge voltage too remained almost constant with the change of electrode separation at the same gas flow velocity. This necessitated revision of the scaling laws for designing this type of high power CO₂ laser. Experimental results of laser performance for different electrode separations are discussed and the modifications in the scaling laws are presented.     

Optoacoustic Laser Stark spectroscopy and FIR laser action on CH3Br using a waveguide CO2 laser

The optoacoustic spectrum of CH₃Br around 10 m band lines of a tunable cw waveguide CO₂ laser is investigated. Several new infrared absorptions are observed and most of the correspond ing molecular transitions are assigned. Far infra red laser action is reported by pumping with the same CO₂ laser: pump offsets are given using the Transferred Lambs dip (TLD) technique. A new FIR laser emission is obtained and assigned. An optoacoustic Laser Stark spectroscopy technique is used to investigate off resonance infrared tran sitions.     

A sequential discharge TEA CO2 laser with high repetition rate and high output power

In this paper, a novel excitation method named as sequential discharge is realized in a two-module TEA CO₂ laser by using a special rotating spark gap. It is demonstrated that the repetition rate and the output power of a laser can be multiplied through this method. For the two-module TEA CO₂ laser in the experiment, the repetition rate is 300 Hz and the average power is 356 W when each module discharges; the repetition rate is 600 Hz and the average power is 713 W when the two modules discharge sequentially.     

Theoretical prediction on the wavelength-temperature shift in pulsed TE CO2 lasers

The wavelength-temperature shift observed in pulsed TE CO₂ lasers is discussed theoretically by means of Six-temperature model rate equations for tunable TE CO₂ lasers. Numerical calculations of the temperature-wavelength shift in a pulsed TE CO₂ laser with a simple plano-concave stable resonator, whether excited by conventional low-inductance fast-discharge scheme or by a long-pulse Pulser/sustainer discharge scheme, show that the laser output wavelengths are within the 10P branch as the ambient temperature varies from 228 to 338 K, but will change as the ambient temperature varies. The laser output wavelengths will move to the transition lines with longer wavelengths in the 10P branch as the ambient temperature increases and vice versa. The calculated results also illustrate that near the ambient temperature of 310 K, the laser is more likely to operate on multi-transition lines. Considering this wavelength-temperature shift, the chilling device adopted in high-power high repetition rate TE CO₂ lasers is important in maintaining a stable laser output spectra as well as a stable laser output power. The numerical results also suggest that a frequency agile resonator is highly recommended if stable laser output spectra are required in TE CO₂ lasers.     

High-power multibeam CO2 laser for industrial applications

Multibeam CO₂ lasers consist of a large number of closely packed parallel glass discharge tubes, all sharing a common plane parallel resonator. This paper describes construction and operation of a CW multibeam CO₂ laser consisting 20 discharge tubes and cooled length of 1500 mm, delivering 1 kW power. A high-frequency pulser is used for producing preionization in all discharge sections for initiating the main DC discharge simultaneously in all discharge tubes. Plane parallel resonator consists of a plane ZnSe mirror of 90 mm diameter having 60% reflectivity and a gold-coated copper mirror of same diameter. This laser operates in waveguide regime and laser power is not critically sensitive to mirror misalignment.     

Examination of CO2 laser-induced rapid solidification structures on magnesia partially stabilised zirconia and the effects thereof on wettability characteristics

The formation mechanism of rapidly solidified microstructures in a magnesia partially stabilised zirconia (MgO-PSZ) following CO₂ laser radiation has been investigated. The influence of laser processing parameters on the microstructures of this material was analysed based on a review of the basic concepts of solidification, the theories of constitutional suppercooling and morphological stability. The different microstructures that were brought about by various laser parameters and appeared across the same track were examined based on the CO₂ laser beam profile of a transverse electromagnetic mode (TEM₀₁). The contact angle measurement revealed a better wettability characteristic of CO₂-laser-modified MgO-PSZ. The clear differences were observed in the change in contact angle for glycerol across the range of rapid solidification microstructures obtained with various power densities. It was therefore determined that the degree of rapid surface resolidification could be the most predominant element governing the wettability characteristics of the MgO-PSZ. The sharp reduction of contact angle for glycerol took place when the cellular microstructure appeared and might be accompanied by the onset of melting on the modified surface of the MgO-PSZ. Moreover, the CO₂ laser treatment also brought about the change in the surface oxygen content and surface roughness. The analysis showed that surface oxygen content was also an influential factor in changing the wettability characteristics of the MgO-PSZ, whilst surface roughness was found to play an insignificant role. The work provides the clear evidence that laser radiation can be a workable and controllable technique to modify the wetting characteristic of the MgO-PSZ.     

New FIR Laser Lines from CHD2OH Methanol

We have investigated CHD₂OH methanol as source of far-infrared (FIR) laser radiation using the optical pumping technique. Our new waveguide pulsed CO₂ laser, with peak powers as high as some kW, has allowed us to observe 12 new lines. Each of them is characterized in wavelength, relative polarization, intensity, optimum operating pressure and pump offset from the center of the exciting CO₂ line.     

Optical fiber cleaved at an angle by CO2 laser ablation: Application to micromachining

Laser ablation can be achieved by delivering short power pulse with durations much smaller than the heat diffusion time. In this investigation, we are collimating and magnifying a beam from a CO₂ laser with a Keplerian telescopic system. Then we study the quality of the cut performed by scanning the beam at a fast speed over an optical fiber just after focusing a well collimated CO₂ beam at λ=10.6 μm. It is found that the best results for cutting optical fibers depend upon both the time required in raising matter temperature to the vaporization point and the scanning speed of the CO₂ laser beam. Some aspects of the laser beam collimation before focusing is reviewed briefly and results for optical fibers being cleaved at low and fast speed under various conditions are also shown and discussed.     

A DC excited waveguide multibeam CO2 laser using high frequency pre-ionization technique

High power industrial multibeam CO₂ lasers consist of a large number of closely packed parallel glass discharge tubes sharing a common plane parallel resonator. Every discharge tube forms an independent resonator. When discharge tubes of smaller diameter are used and the Fresnel numberN ≪ 1 for all resonators, they operate in waveguide mode. Waveguide modes have excellent discrimination of higher order modes. A DC excited waveguide multibeam CO₂ laser is reported having six glass discharge tubes. Simultaneous excitation of DC discharge in all sections is achieved by producing pre-ionization using an auxiliary high frequency pulsed discharge along with its other advantages. Maximum 170 W output power is obtained with all beams operating in EH₁₁ waveguide mode. The specific power of 28 W/m is much higher as compared to similar AC excited waveguide multibeam CO₂ lasers. Theoretical analysis shows that all resonators of this laser will support only EH₁₁ mode. This laser is successfully used for woodcutting     

Surface evolution and laser damage resistance of CO2 laser irradiated area of fused silica

A 10.6 μm CO₂ laser has been reported to effectively mitigate the laser damage growth of fused silica. Two zones of the laser irradiated area are defined in this work: the distorted zone and the laser affected zone. The parameters of the two zones are studied at different CO₂ laser beam sizes, irradiation times, and powers by microscopy, profilometry, and photoelastic method. The results show that the diameter of laser affected zone is almost completely determined by the laser beam size and the distorted zone is associated with the mitigation range of CO₂ laser beam. The diameter and depth of the distorted zone increase as the laser power and irradiation time increase. The depth grows exponentially depending on the irradiation time. The maximum residual stress discrepancy is located near the boundary of the laser affected zone. The laser damage resistance test results show that the distorted zone and the laser affected zone have a better damage resistance than the original substrate.