乙烯在纳米催化剂InVO4-TiO2上的可见光降解

The InVO₄-TiO₂ nano-crystalline photocatalyst was prepared by sol-gel method and characterized by DRS, FTIR, Raman and XRD. The photocatalytic activities of the prepared sample were investigated by photocatalytic degradation of ethylene in the gaseous phase under visible light irradiation (λ>450 nm). The results indicate that both of pure TiO₂ and InVO₄ or their simple mixture show no photocatalytic activities for degradation of ethylene under visible light irradiation. However, as-synthesized InVO₄-TiO₂ catalyzes the degradation of ethylene into CO₂ under visible light irradiation. In addition, the interaction between InVO₄ and TiO₂ results in some structural distortion to all the crystal forms of TiO₂ in as-synthesized catalyst InVO₄-TiO₂.     

Pt / InVO4 / TiO2可见光催化剂的制备及性能研究

采用溶胶-凝胶法制备了Pt / InVO₄ / TiO₂三元体系可见光催化剂。以乙烯为模拟目标分子，评价其光催化活性并与二元体系催化剂Pt / TiO₂ 和InVO₄ / TiO₂进行比较。用DRS，XRD对催化剂的吸收带边和晶型进行了表征。结果表明：Pt / InVO₄ / TiO₂在可见光区（λ>450 nm）的光催化比活性比Pt / TiO相似文献   

Na4Ca(SO4)3复盐高温合成及温度对晶体形貌的影响

用高温合成法制备出硫酸钙复盐Na₄Ca(SO₄)₃，利用差热分析、X射线衍射、扫描电子显微分析等现代测试仪器研究了该复盐的反应历程。研究结果表明，其反应过程按CaSO₄+Na₂SO₄→(Na_0.8Ca_0.1)₂SO₄→Na₄Ca(SO₄)₃进行。Na₄Ca(SO₄)₃为高温稳定相，其最佳合成温度为800 ℃～1 100 ℃。育晶温度及时间对复盐形貌有明显影响，在1 000 ℃保温2 h后转到945 ℃育晶5 h,晶体生长较好。     

可见光响应的Co3(PO4)2/Ag3PO4纳米复合光催化剂的制备及表征

采用简单的化学偏聚法合成出Ag₃PO₄纳米颗粒、磷酸钴（Co₃（PO₄）₂,CoP）纳米片以及它们两者的纳米复合结构（CoP/Ag₃PO₄）,同时还比较了它们的可见光催化活性. 采用场发射扫描电镜（FESEM）、X 射线衍射（XRD）、紫外-可见（UV-Vis）吸收光谱以及光致发光谱等手段对其形貌、结构、光学以及可见光催化性能等进行表征. 结果表明,CoP/Ag₃PO₄复合纳米结构的可见光降解甲基橙（MO）的速率和循环稳定性均明显优于其它两种物质. 这表明CoP应该起着共催化剂的作用,它能够抑制光生电子与空穴之间的复合,并且提供大量高活性的光生空穴. 此外,我们还发现CoP/Ag₃PO₄降解另一种阳离子型染料——罗丹明B（RhB）的能力则远不如纯Ag₃PO₄,这可能是与光催化剂的表面性质发生改变有关,造成更低的RhB吸附能力. 本文提供了一种廉价制备高效可见光催化剂的新方法.     

K3Na(FeO4)2的电合成及其晶体结构

本文采用间接法电合成出较高纯度的复盐K₃Na(FeO₄)₂晶体，用粉末XRD结构分析法对其晶体结构作了详细研究。用EDX和AAS确认了其化学式。结构分析表明，K₃Na(FeO₄)₂晶体属三方晶系，具有六方晶胞，空间群为P3m1(No.164)，Z=1,晶胞中有6个O位于6(i)位，O,Fe和K各自有2个位于2(d)位，1个K和Na分别位于1(b)位和1(a)位，晶胞参数a=0.583 3(1) nm,c=0.755 9(1) nm，D=2.824 g·cm^-3。同时晶胞中各原子间化学键键长得到确定。     

表面活性剂辅助合成CdWO4纳米棒和纳米线

以Na₂WO₄•2H₂O和CdCl₂ 为主要原料, 分别在十六烷基三甲基溴化铵(CTAB)和十二烷基苯磺酸钠(SDBS)表面活性剂中, 在180 ℃反应16 h, 水热制备了CdWO₄纳米棒和纳米线. 利用X射线粉末衍射(XRD)、透射电子显微镜(TEM)和高分辨透射电子显微镜(HRTEM)等手段对产物进行了表征, 并对其在室温下的发光特性进行了测定. 实验结果表明: 产物均为具有单斜结构的单相CdWO₄. 其中CdWO₄纳米棒具有单晶属性, 平均粒径约为63 nm, 长度近1 µm; 而CdWO₄纳米线具有多晶特性, 平均粒径约为12 nm, 长度达十几微米. 当激发波长为253 nm时均有460 nm强的发射峰, 其中CdWO₄单晶纳米棒的发光强度大于CdWO₄多晶纳米线. 分别对CdWO₄纳米棒和纳米线形成的可能机理进行了初步分析.     

表面活性剂辅助合成CdWO4纳米棒和纳米线

以Na₂WO₄•2H₂O和CdCl₂ 为主要原料, 分别在十六烷基三甲基溴化铵(CTAB)和十二烷基苯磺酸钠(SDBS)表面活性剂中, 在180 ℃反应16 h, 水热制备了CdWO₄纳米棒和纳米线. 利用X射线粉末衍射(XRD)、透射电子显微镜(TEM)和高分辨透射电子显微镜(HRTEM)等手段对产物进行了表征, 并对其在室温下的发光特性进行了测定. 实验结果表明: 产物均为具有单斜结构的单相CdWO₄. 其中CdWO₄纳米棒具有单晶属性, 平均粒径约为63 nm, 长度近1 µm; 而CdWO₄纳米线具有多晶特性, 平均粒径约为12 nm, 长度达十几微米. 当激发波长为253 nm时均有460 nm强的发射峰, 其中CdWO₄单晶纳米棒的发光强度大于CdWO₄多晶纳米线. 分别对CdWO₄纳米棒和纳米线形成的可能机理进行了初步分析.     

新型配合物Mn2Hg4(SCN)12的合成与晶体结构分析

A new inorganic coordination compound Mn₂Hg₄(SCN)₁₂ was synthesized. The grown crystals were characterized by elemental analysis, infrared spectroscopic analysis and powder crystal X-ray diffraction in detail. The crystal structure of Mn₂Hg₄(SCN)₁₂ was determined by single-crystal X-ray diffraction. It belongs to monoclinic system, P2₁/c space group. The cell dimensions are: a=1.171 6 nm, b=1.431 05 nm, c=2.105 1 nm, β=100.738°, and Z=4. In the structure of it, half of Mn²⁺ cations have five-coordinate number, and other half of Mn²⁺ cations have six-coordinate number; 3/4 of Hg²⁺ cations are coordinated by four SCN^-, 1/4 of Hg²⁺ cations are coordinated by three SCN^- and one NCS^-, all the coordination geometry of Hg²⁺ show slightly distorted tetrahedrons. CCDC: 244939.     

低温烧结NaBi(WO4)2陶瓷的介电性能

采用固相合成法制备了（WO₄）₂（NBW）陶瓷,研究了NBW陶瓷的相结构、形貌、烧结特性和微波介电性能。NBW陶瓷在625~800℃烧结1~4 h能够致密化。X射线衍射表明在625~800℃烧结2 h的NBW陶瓷均为四方晶系白钨矿结构的单相陶瓷。随着烧结温度的提高,NBW陶瓷的介电常数、品质因数（Qf值）先增加后降低,谐振频率温度系数逐渐降低。经650℃烧结2 h获得的NBW陶瓷的介电常数为14.36,Qf值为16 503 GHz,谐振频率温度系数为-1.055×10-5℃^-1。NBW陶瓷与银共烧反应生成Ag₂W₂O₇相,而与Au、Al共烧具备化学兼容性。     

(ZrO2)0.92(Gd2O3)0.08纳米晶的水热合成及其烧结体的电性能

用新制备的(Gd，Zr)(OH)_x·yH₂O共沉淀作前驱体，在强碱性介质中用水热法合成了(ZrO₂)_0.92(Gd₂O₃)_0.08纳米立方晶，考察了反应温度、pH值等水热反应条件对纳米晶粒大小的影响。将(ZrO₂)_0.92(Gd₂O₃)_0.08     

Synthesis, characterization, and photocatalytic properties of InVO4 nanoparticles

Nanosized InVO₄ with orthorhombic structure was successfully synthesized at a relatively low calcination temperature of 600 °C by using an amorphous heteronuclear complex as precursor. The photocatalytic activity of InVO₄ catalyst has been evaluated by the decomposition of formaldehyde (FAD) under UV light () and visible light irradiation (). The as-synthesized InVO₄ catalyst showed higher photocatalytic activity for the FAD decomposition compared to the sample prepared by the conventional solid-state reaction. The calculations of the electronic band structures indicated that the valence band was composed of the O 2p orbitals, whereas the conduction band was formed by the V 3d orbitals with a small contribution of the In 5s orbitals. The photocatalytic activity of the as-prepared sample is discussed on the basis of the electronic band structure and bulk material structure.     

Formation and performances of porous InVO4 films

Porous complex oxide films consisting of preferentially orientated orthorhombic phase of InVO₄ have been prepared using a novel simple method by pyrolysis of amorphous complex precursor. The formation and controlling of porous InVO₄ films can be easily obtained by modifying the calcination temperature. The pure orthorhombic InVO₄ phase can be obtained at a relatively lower temperature (500 °C), and the films are preferential orientation of the (200) face parallel to the substrate. The phase separation mechanism was suggested for the formation of porous films. Under visible light irradiation (λ>400 nm), porous InVO₄ films have shown the photocatalytic activity for photodegradation of gaseous formaldehyde, and can generate photocurrent. The electrochemical properties of the films with different crystal structure and pore structure were also investigated.     

低温固相反应合成Li3V2(PO4)3正极材料及其性能

利用V₂O₅·nH₂O湿凝胶，LiOH·H₂O，NH₄H₂PO₄和C等作原料，通过低温固相还原反应在550 ℃焙烧12 h制备出Li₃V₂(PO₄)₃正极材料。采用XRD，SEM和电化学测试对Li₃V₂(PO₄)₃样品性能进行研究。XRD研究表明本法所合成的Li₃V₂(PO₄)₃同传统的高温固相反应法所合成的Li₃V₂(PO₄)₃一样同属于单斜晶系结构。SEM测试表明所合成的样品平均粒径大小约为0.5 μm且粒径分布较窄。电化学测试表明以0.2 C的倍率放电时，样品的首次放电容量为130 mAh·g^-1，室温下循环30次后其比容量为124 mAh·g^-1。     

Temperature behavior of the protonic conductor K4LiH3(SO4)4

The results of the X-ray structural study for the K₄LiH₃(SO₄)₄ single crystal are presented at a wide temperature range. The thermal expansion of the crystal using the X-ray dilatometry and the capacitance dilatometry from 8 to 500 K was carried out. The crystal structures data collection, solution and refinement at 125, 295, 443 and 480 K were performed. The K₄LiH₃(SO₄)₄ crystal has tetragonal symmetry with the P4₁ space group (Z=4) at room temperature as well as at the considered temperature range. The existence of a low-temperature, para-ferroelastic phase transition at about 120 K is excluded. The layered structure of the crystal reflects a cleavage plane parallel to (001) and an anisotropy of the protonic conductivity. The superionic high-temperature phase transition at T_S=425 K is isostructural. Nevertheless, taking into account an increase of the SO₄ tetrahedra libration above T_S, a mechanism of the Grotthus type could be applied for the proton transport explanation.     

Synthesis, crystal structure, infrared and Raman spectra of Sr4Cu3(AsO4)2(AsO3OH)4·3H2O and Ba2Cu4(AsO4)2(AsO3OH)3

The two new compounds, Sr₄Cu₃(AsO₄)₂(AsO₃OH)₄·3H₂O (1) and Ba₂Cu₄(AsO₄)₂(AsO₃OH)₃(2), were synthesized under hydrothermal conditions. They represent previously unknown structure types and are the first compounds synthesized in the systems SrO/BaO-CuO-As₂O₅-H₂O. Their crystal structures were determined by single-crystal X-ray diffraction [space group C2/c, a=18.536(4) Å, b=5.179(1) Å, c=24.898(5) Å, β=93.67(3)°, V=2344.0(8) Å³, Z=4 for 1; space group P4₂/n, a=7.775(1) Å, c=13.698(3) Å, V=828.1(2) Å³, Z=2 for 2]. The crystal structure of 1 is related to a group of compounds formed by Cu²⁺-(XO₄)³⁻ layers (X=P⁵⁺, As⁵⁺) linked by M cations (M=alkali, alkaline earth, Pb²⁺, or Ag⁺) and partly by hydrogen bonds. In 1, worth mentioning is the very short hydrogen bond length, D···A=2.477(3) Å. It is one of the examples of extremely short hydrogen bonds, where the donor and acceptor are crystallographically different. Compound 2 represents a layered structure consisting of Cu₂O₈ centrosymmetric dimers crosslinked by As1φ₄ tetrahedra, where φ is O or OH, which are interconnected by Ba, As2 and hydrogen bonds to form a three-dimensional network. The layers are formed by Cu₂O₈ centrosymmetric dimers of CuO₅ edge-sharing polyhedra, crosslinked by As1O₄ tetrahedra. Vibrational spectra (FTIR and Raman) of both compounds are described. The spectroscopic manifestation of the very short hydrogen bond in 1, and ABC-like spectra in 2 were discussed.     

Synthesis, characterization, and structure determination of the orthorhombic U2(PO4)(P3O10)

β-UP₂O₇ has been synthesized under hydrothermal conditions (θ=500°C, P=200 MPa), using UO₂ and H₃PO₄. β-UP₂O₇ crystallizes in the orthorhombic space group Pn2₁a, with a=11.526 (2) Å, b=7.048 (2) Å, c=12.807 (2) Å and Z=4. Its structure has been determined through direct methods and difference Fourier synthesis and has been refined to R=0.0396. The structure is built on UO₈ polyhedral chains along the b-axis. PO₄³⁻ and P₃O₁₀⁵⁻ groups coexist in the structure and the latter groups form non-linear chains. Cohesion of the structure is made through the linkage of UO₈ chains by PO₄ and P₃O₁₀ groups leading to the formula U₂(PO₄)(P₃O₁₀) instead of β-UP₂O₇. Vibrational and optical spectra confirm the results obtained by X-ray diffraction. DTA-TGA measurements show that the transformation of U₂(PO₄)(P₃O₁₀) to the cubic α-UP₂O₇ occurs at θ=870°C.