等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

Ni-B非晶态合金中电子转移问题的DFT研究

根据Ni-B非晶态结构的短程有序、Ni和B之间是较强的化学作用和结构中存在B-B直接相连的实验事实,选择了Ni~mB~2^(^1^)(m=1-4)原子簇模型,用DFT方法对其进行高水平的量子化学计算,结果表明,模型体系中,B原子供给Ni原子电子,这与非晶态合金的实验结果一致,为了此较,同时选择了NiB^(^2^)(m=1-4)模型,计算结果与实验不符,这说明NiB~2^(^1^)(m=1-4)原子簇模型更能反映非晶态的结构特点。     

Ni-P非晶态合金中电子转移问题的DFT研究

根据Ni-P非晶态合金结构的短程有序、Ni和P之间具较强化学作用和结构中不存在P-P直接相连的实验事实,选择了Ni~nP(n=1-6)原子簇模型,用密度泛函理论方法对其进行计算。结果表明,在模型体系中,随着P含量的减少,电子转移方向发生变化,P原子由得电子变为失电子。这与Ni-P非晶态合金的实验结果一致,说明Ni~nP(n=1-6)原子簇模型能反映Ni-P非晶态合金的结构特点。     

Quantum Chemical Study on Geometry and Property of Cluster Ni_4P

1INTRODUCTION Amorphous alloys attractive to scientists have worked in the field of materials and catalysts since they have many excellent physical and chemical pro-perties,such as high magnetic susceptibility,high specific heat,high strength,ductile in compression,low coefficient of friction,high corrosion resistance,super plasticity within the range,ferromagnetism and super conductivity[1~5].Especially,amorphous alloys as catalytic materials have shown either hig-her activity or selectiv…     

Ni-B非晶态合金局域结构和电荷转移性质的理论研究

根据非晶态合金结构的短程有序、Ni和B间存在较强的化学作用、结构中存在B－B键直接相连的实验事实,选择Ni~mB~2(m=1,2,4)原子簇作为非晶态局域结构的计算模型。考虑原子簇间的相互作用,又对[Ni~4B~2]~n(n=1,2,5,7)簇团进行了系统计算。结果表明在所选Ni-Br的簇模型中,都是B原子提供电荷给Ni原子,这些均与非晶态合金实验结果和一些理论计算结果相符。簇团的计算结果还表明,小原子簇Ni~4B~2内原子间存在较强的化学键作用,而簇间的相互作用相对较弱,很容易造成对称性破缺而导致产生长程无序,因此Ni-B非晶态可以被看成是由大量i上原子簇无序堆砌成的,这一点也同实验事实相吻合。计算结果也表明我们前面工作中所取的和最常见的Ni-B非晶态合金Ni~6~4B~3~6有相似组成的Ni~4B~2原子簇模型能在一定程度上反映Ni-B非晶态合金的局域结构特征。     

载体TiO2对Co-P非晶态合金性质的影响

用还原沉积法分别合成了纯态Co-P非晶态合金和一种新型负载非晶态合金催化剂CoP/TiO₂, 用XRD, ICP, TEM, BET和DSC等手段对催化剂的物理性质进行了表征, 比较了它们的结构、组成、形貌、表面积及热稳定性等物理性质及其对PH₃分解的催化活性. 与纯态Co-P非晶态合金比较, CoP/TiO₂具有更大的表面积和较高的热稳定性及催化活性, 这缘于TiO₂载体与催化剂的相互作用以及载体对Co-P良好的分散性能.     

Theoretical Study on the Catalytic Activity and Sulfur Resistibility of Amorphous Alloy Ni-B-P

In the present paper,one hundred cluster models NinBP (n=1～6) have been designed and studied by density functional theory (DFT) to get an insight into the local structure,catalytic properties and sulfur resistibility of amorphous alloy Ni-B-P. The configurations in triplet state are found more stable than those in the singlet state. It is found that as the content of Ni in the clusters increases,the value of Fermi level in clusters fluctuated,which shows that the content of Ni can influence the Fermi level to a certain extent. Based on the Fermi level and DOS,we consider the activity of catalyst in hydrogenation reaction is the best in cluster Ni3BP. On the basis of the charge of clusters NinBP (n=1～6),we conclude the amorphous alloy Ni-B-P with high Ni content has better sulfur resistibility and the best hydrogenation activity,strong sulfur resistibility appears in clusters Ni3BP,and the amorphous alloy Ni60B20P20 with similar proportion is expected to prepare in the future.     

Synthesis and X-ray characterization of the phosphido-carbonyl cluster anions

The [Co(9)P(CO)(21)](2)(-) anion has been isolated from the products of the reaction between Na[Co(CO)(4)] and PCl(5) in tetrahydrofuran at reflux. The structure of the cluster anion [Co(9)P(CO)(21)](2)(-) in its tetraphenylphosphonium salt has been elucidated by X-ray analysis. The crystals are monoclinic, space group P2(1)/n, a = 12.528(3), b = 14.711(5), c = 19.312(6) A, beta = 93.68(2) degrees, Z = 2. Final R = 0.065 for 2300 unique reflections having I > 3sigma(I). The anion, which is disordered about an inversion center, consists of a monocapped square antiprismatic cluster containing an interstitial phosphide and surrounded by 13 terminal and 8 edge-bridging carbonyl ligands. Average values are: Co-Co 2.685 A, and Co-P 2.256 A. The [Co(10)P(CO)(22)](3)(-) anion has been obtained by condensation of the [Co(9)P(CO)(21)](2)(-) anion with [Co(CO)(4)](-) in tetrahydrofuran at reflux. While the [Co(9)P(CO)(21)](2)(-) anion is stable under CO, the [Co(10)P(CO)(22)](3)(-) anion is decomposed to [Co(9)P(CO)(21)](2)(-) and [Co(CO)(4)](-). The benzyltrimethylammonium salt of the [Co(10)P(CO)(22)](3)(-) anion has been studied by X-ray analysis. It gives triclinic crystals, space group P_1, a = 11.452(3), b = 23.510(6), c = 25.606(4) A, alpha = 112.46(1), beta = 95.79(1), gamma = 73.548(2) degrees, Z = 4. Final R = 0.041 for 8600 unique reflections having I > 3sigma(I). There are two independent trianions in the asymmetric unit, both showing similar geometries, consisting of bicapped square antiprismatic clusters with a central P atom, each bearing 10 terminal and 12 edge-bridging carbonyl ligands, 8 of which, bound to the capping metals, are markedly asymmetric. Average values are: Co-Co 2.678 A, and Co-P 2.262 A. Electrochemistry shows that [Co(9)P(CO)(21)](2)(-) and [Co(10)P(CO)(22)](3)(-) in acetonitrile solution undergo either a one-electron oxidation or a two-electron reduction. This latter process appears as a single step in the case of the dianion and as two separated one-electron steps in the case of the trianion. All the processes are accompanied by slow chemical complications, thus testifying that no stable redox congeners exist for these phosphide clusters.     

Ni-Co-B非晶态合金催化剂用于氯代硝基苯液相加氢制氯代苯胺

 用化学还原法制备了 Ni-Co-B 非晶态合金催化剂,并采用透射电子显微镜、扫描电子显微镜、选区电子衍射、X射线衍射、X射线能谱和差热-热重分析等表征手段研究了催化剂的非晶性质和原子组成等. 将此催化剂用于邻氯硝基苯和 3,4-二氯硝基苯的液相催化加氢反应,结果表明,当Co/(Co+Ni)=0.5 (摩尔比)时, Ni-Co-B 催化剂具有较好的加氢性能和较高的抑制脱卤性能. 在不加脱卤抑制剂的情况下,两种氯代硝基苯的转化率均接近100%, 脱卤率分别为1.12%和0.42%, 优于使用 Ni-B 和 Co-B 非晶态合金催化剂时的结果. 还讨论了将Co引入到 Ni-B 非晶态合金催化剂时对其性能的影响.     

超细Co-B非晶态合金的制备及其催化乙腈加氢性能

报道了 一种用 于乙腈加 氢的 新 型 复合 型 催化 剂 超细 Ｃｏ Ｂ 非 晶 态合 金（ 粒 径 ６０ ｎ ｍ左右） , 其催 化性能显 著优于 其它 Ｃｏ 基催 化剂． 以此代替 工业用 Ｒａｎｅｙ Ｎｉ , 不 仅可 提高 对乙 胺的选择性 ,而且可 显著减轻 环境污 染． 通 过一系列 表征,讨 论了乙腈 在催化 剂活性位 的吸附 模式及催化加氢 反应机 理,由此对 其催化 性能与催 化剂结 构的关系 进行了说 明．     

Theoretical study of structure and photoelectron spectroscopy of In(x)P(y)- and In(x)P(y) (x + y < or = 6) clusters

The geometries and vibrational frequencies of In(x)P(y)- and In(x)P(y) are investigated by hybrid B3LYP functional for x + y < or = 6 and CCSD(T) method for x + y < or = 3. As for the small clusters having two to three atoms, the geometrical and electronic structures and vibrational frequencies at the B3LYP level are in good agreement with those at the CCSD(T) level. Among the most stable structures of In(x)P(y)- and In(x)P(y) (x + y < or = 6) clusters the P-rich clusters are more stable than In-rich clusters. Moreover, we found that those P atoms in In(x)P(y)- and In(x)P(y) (x + y < or = 6) clusters prefer to form a P-P bond, triangle, quadrangle, and pentagon for y = 2, 3, 4, and 5, respectively. Also, the vertical detachment energies of In(x)P(y)- (x + y < or = 6) and electron affinities of In(x)P(y) (x + y < or = 6) clusters obtained by B3LYP are in good agreement with the experimental values available. Theoretically, we show that the electron affinity of In3P3 is very low because, as observed in the experiment, there is a formation of a new P-P bond after an electron is lost from In(3)P(3)-, and we find that the similar phenomena exhibit in In2P4(-) cluster as well.