Determination of trace elements in marine plankton by inductively coupled plasma mass spectrometry (ICP-MS)

A method has been developed for the determination of 23 elements in marine plankton in which inductively coupled plasma (ICP) source mass spectrometry (MS) was used to quantify the elements in the solution after digestion in a mixture of hydrofluoric and nitric acids in sealed PTFE vessels in a microwave field. The procedure was validated by the analysis of a standard reference soil (SRM 2709 San Joaquin Soil) and a standard reference fresh water plankton (CRM 414). The method was applied to the analysis of several marine plankton samples grown under controlled conditions including several whose growth media had been enriched with selenium. Matrix induced signal suppressions and instrumental drift were corrected by internal standardization. The suitabilities of germanium, indium, rhodium, scandium and yttrium as internal standard elements were evaluated. Neither scandium nor yttrium could be used due to the presence of these elements in the samples, germanium was used for the determination of As, Co, Cu, Fe, Ni, Se, Si and Zn, indium was used for Al, Ba, Ca, Eu, Sr, and Tl, and rhodium was used for Cd, Cr, Hg, Mg, Pb, Sb, Sn, and V. For Al, Ca, Cr, Cu, Fe, Mg, Mn, Ni, Si, Sr, V, and Zn internal standardization did not completely compensate for the suppressive effect of the heavier elements and the solutions were diluted. However, for As, Ba, Cd, Co, Eu, Hg, Pb, Sb, Se, Sn and Tl, it was possible to obtain accurate results despite the 35–¶40% suppression in the signals. Isobaric overlap was only a problem in the cases of ⁴²Ca and ⁷⁸Se; ⁴⁴Ca and ⁷⁷Se, respectively, were used. Memory effects were only observed with Hg for which a nitric acid-sodium chloride solution was the most effective wash-out solution. The marine plankton samples were able to tolerate a higher concentration of Hg as the selenium concentration increased.     

ICP-AES analysis of metal content in shell of mussel Mytilus galloprovincialis from Croatian coastal waters

Metal content in samples of shell of mussel Mytilus galoprovincialis was determined by inductively coupled plasma atomic emission spectrometry (ICP-AES). The efficiency of conversion of crude samples into solution by acid digestion in an open plate and in a microwave oven was examined by use of certified reference material of marine sediment and laboratory made standards of calcite and aragonite. Influence of high Ca content matrix on emission intensities of Al, Ba, Cd, Cu, Fe, Mg, Mn, Na, Ni, Pb, Sr and Zn was observed as depression of emission signal for most of the measuring elements, ranging from 0.8% to 8%. Greater values were noted at Ba and Ni emission lines. Enhancement of signals was observed for Na and Mg lines. The determination of As, Sb, Se and Sn was performed by HG/ICP-AES. The greater abundance of Sn was found in samples collected near the Al-processing industry centre. No detectable concentrations of As, Sb, and Se were found in shell samples. Results of ICP-AES metal analysis showed that samples collected near harbours, city waste or sewage outlets, and chemical industry centres indicate the certain level of contamination. It is shown that shell analysis provides useful data in determination of marine environment status.     

Determination of 21 elements by INAA for certification of SRM 1570a,Spinach

Analyses for certification have been made by instrumental neutron activation analysis (INAA) for the determination of 21 elements in the National Institute of Standards and Technology (NIST) Spinach renewal reference material, SRM 1570a. Elements determined included ones with short halflife products (Al, V, Ca, Mg), intermediate halflife products (Mn, Na, K, La), and long halflife products (Ba, Co, Cr, Cs, Eu, Fe, Rb, Sb, Sc, Se, Sr, Th, and Zn). For the first time a new robotic sample changer was used in the counting of long halflife indicator isotopes for certification of an SRM. Uncertainties obtained averaged±1.80% for the four major and minor constituents (Ca, K, Mg, Na); ±3.14% for elements with concentrations from 1 to 400 mg/kg (Al, Ba, Cr, Fe, Mn, Rb, Sr, and Zn); and±8.31% for the ultra trace elements (<1 mg/kg) (Co, Cs, Eu, La, Sb, Sc, Se, Th, and V).     

Neutron activation as a routine method for the determination of trace elements in water

By freeze-drying the following elements can be determined in natural water except sea water: Au, Ba, Br, Ca, Ce, Co, Cr, Eu, Fe, K, La, Mo, Na, Sb, Sc, Se, U, Zn. Some problems may arise with respect to As and Hg. Cu, Cd and Ni can only be determined if present in high concentrations. Separation by adsorption on charcoal in presence of complexing agents gives yields between 75 and 100% for the following elements in sea water: Ag, Au, Cd, Ce, Co, Cr, Eu, Fe, Hg, La, Mo, Sc, Se, U, Zn (As 67%, Sb 56%). Activation or use of labelled ions and study of exchange give information about mobility of trace elements in suspended matter.     

Some trace elements in the waters,marine organisms and sediments of the Adriatic by neutron activation analysis

A number of investigations of trace elements in the waters, organisms and sediments of the Adriatic, using neutron activation analysis with radiochemical, separations are reported. These include studies of Hg in mussels from the Northern Adriatic, of Hg and Se in edible animals from the Rijeka region, and of seven elements (As, Cd, Cu, Hg, Mn, Se and Zn) in marine invertebrates from the Slovene coast. Additionally, plankton, sediment cores and water samples were taken from a grid of stations covering the whole Adriatic and analyzed for 6 to 11 of the trace elements As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Sb and Zn (Hg only in water). Generally, levels found were not indicative of pollution as compared with oceanic samples, but some evidence of locally increased levels was found, especially for Hg. The levels of eleven trace elements in three marine Intercomparison samples prepared by the IAEA Monaco Laboratory are also presented.     

Instrumental neutron activation analysis of high-purity gallium,arsenic, and gallium arsenide

Instrumental neutron activation analysis (INAA) has been applied to obtain useful data on impurity concentrations in ultra-pure materials whose matrix elements are strongly activated and create severe interference for several weeks after irradiation. An analytical procedure has been developed and used to determine Sc, Fe, Co, Zn, Se, Zr, Ag, In, Sn, Sb, Te, and Hg in high-purity gallium, arsenic, and gallium arsenide. Detection limits ranged from 50 ng/g for iron to 0.001 ng/g for scandium. Problems of contamination control, blank level, and standardization are discussed.     

微波消解-ICP-OES法测定汽车涂料中8种重金属

建立微波消解-电感耦合等离子体发射光谱(ICP-OES)测定汽车涂料中Pb,Cr,Se,Ba,Sb,As,Cd,Hg含量的方法。以HNO_3-H_2O_2(体积比为4∶1)混合酸消解样品,各元素分析谱线:Pb 220.353 nm,Cr 267.716 nm,Se196.090 nm,Ba 233.527 nm,Sb 217.581 nm,As 189.042 nm,Cd 228.802 nm,Hg 184.950 nm。8种元素测定结果的相对标准偏差为2.02%~12.94%(n=6);对白色、蓝色、红色汽车漆样品进行加标回收试验,Pb,Cr,Se,Ba,As,Cd,Hg,的加标回收率为81.26%~99.79%,Sb的回收率为62.43%~87.61%。该方法快速、简便,精密度、准确度较高,可用于汽车涂料中重金属含量的监控。     

Selective separation of indium from zinc, lead, gallium and many other elements by cation-exchange chromatography in hydrohalic acid-acetone medium

Indium can be separated from Zn, Pb(II), Ga, Ca, Be, Mg, Ti(IV), Mn(II), Fe(III), Al, U(VI), Na, Ni(II) and Co(II) by selective elution with 0.50M hydrochloric acid in 30% aqueous acetone from a column of AG50W-X8 cation-exchange resin, all the other elements being retained by the column. Lithium is included in the elements retained by the column when 0.35M hydrochloric acid in 45% aqueous acetone is used for eluting indium, but the elution of indium is slightly retarded. Ba, Sr, Zr, Hf, Th, Sc, Y, La and the lanthanides, Rb and Cs should also be retained according to their distribution coefficients. Cd, Bi(III), Au(III), Pt(IV), Pd(II), Rh(III), Mo(VI) and W(VI) can be eluted with 0.20M hydrobromic acid in 50% aqueous acetone before the elution of indium, and Ir(III), Ir(IV), As(III), As(V), Se(IV), Tl(III), Hg(II), Ge(IV), Sb(III) and Sb(V), though not investigated in detail, should accompany these elements. Relevant distribution coefficients and elution curves and results for analyses of synthetic mixtures of indium with other elements are presented.     

Characterization of deep sea sediments by INAA for radioactive waste management purposes

An instrumental neutron activation analysis method, using both reactor flux and epi-cadmium neutrons, has been developed for the determination of major, minor and trace elements in sub-seabed sediments. The method involves two different irradiations followed by three different counting periods using high-resolution Ge(Li) and low-energy photon detectors. The list of elements determined includes Ag, Al, As, Ba, Br, Ca, Ce, Cl, Co, Cr, Cs, Dy, Eu, Fe, Ga, Gd, Hf, Hg, I, In, K, La, Lu, Mg, Mn, Mo, Na, Nd, Ni, Pt, Rb, Re, Rh, Sb, Sc, Se, Si, Sm, Sn, Sr, Ta, Tb, Th, Ti, Tm, U, V. W, Yb, Zn, and Zr. The accuracy of the method has been evaluated by analyzing four different standard reference materials. The method has been applied to core samples collected from the Great Meteor East and the South Nares Abyssal Plain which are being evaluated as potential sites for the possible disposal of vitrified highly active waste.     

前列舒通胶囊中26种无机元素的分析

目的：明确造成前列舒通胶囊不同批次间差异的标志性无机元素,并进行安全性评价。方法：采用ICP-MS测定制剂中Al、As、B、Ba、Ca、Cd、Co、Cr、Cu、Fe、K、Mg、Mn、Mo、Na、Ni、Pb、Sb、Se、Sn、Sr、Ti、Tl、V、Zn和Hg元素含量并进行数据分析。运用主成分及综合评分结合聚类分析手段,确定制剂的特征性元素;进行元素含量和相关性分析,明确不同批次各元素的差异及元素之间的关系;以多元素含量为指标,绘制无机元素谱图。结果：19批样品中均未检测出Se、Mo、Sn、Sb、Tl和Hg,且Pb、Cd、As、Cu、Hg均符合限量标准,无机元素含量谱图趋势一致。主成分分析提取了4个主成分,确定元素B、K、Al、V、Cr、Ca、Ti、Na、Co和Mn可作为特征元素。主成分得分图将19批样品分为两类,聚类分析及综合评分结果与其一致,两类样品中各元素含量存在差异性。相关性分析中,明确了B与K、Al、Cr正相关,K与Cr、Co正相关,V与Cr、Mn正相关,Mn与Co正相关,Ca、Ti、Na两两正相关。结论：通过分析前列舒通胶囊中无机元素含量,确定了特征元素,为前列舒通胶囊质量全面控制研究提供科学依据。     

Multielement analysis of Chinese Biological Standard Reference Material by monostandard instrumental neutron activation analysis

A procedure for monostandard INAA of 21 elements (Hg, As, Br, Cr, Sb, Se, Ba, Zn, Ca, Ce, Co, Cs, Eu, Fe, Hf, K, La, Rb, Sc, Sr, Ta) in Chinese Biological Standard Reference Material (peach leaves) is described. The accuracy of the procedure was checked by analyzing the U.S. NBS Standard Reference Materials SRM-1571 and SRM-1632a.     

Neutron activation analysis of some North Adriatic organisms

The present work was undertaken to contribute additional information on the concentration of microelements in marine organisms, and especially on the ecological characteristics of the North Adriatic Sea. Samples of biota were collected during 1976 and 1980 from various parts of the west Istrian coast. All samples (Mytilus galloprovincialis Lam. and Zostera marina L.) were dried at 110°C to a constant weight, homogenized and powdered and subjected to instrumental neutron activation analysis. The biota in North Adriatic contain a relatively high concentration of microelements, mainly Fe, Co, Se, Sr, Eu, Sc and Cs. The results indicated that Zostera marina L. accumulates most of the investigated elements and that concentration factors especially for europium, iron, scandium and selenium are very high.     

Determination of trace elements in petroleum by neutron activation analysis

Instrumental neutron activation analysis (INAA) and Ge(Li) spectrometry have been used to determine Sc, Cr, Fe, Co, Ni, Zn, As, Se, Sb, Eu, Au, Hg, and U in crude petroleum. The technique involves no chemical separations and no pre-concentration of the samples by ashing is necessary, thus avoiding contamination or loss of volatile elements. The estimated detection limits in ppb for the elements are Sc (0.1), Cr (0.16), Fe (400.0), Co (0.6), Ni (1.1), Zn (200.0), As (6.0), Se (23.0), Sb (1.0), Eu (0.58), Au (0.11), Hg (4.3), U (1.5). Precision values ranged from 0.1% to 15% (relative standard deviation). Interferences in the Co and Fe determinations due to fast neutron reactions (n, p) and (n, α) on Ni isotopes are small and are easily corrected. Losses of As, Se, and Hg due to escape of volatile gases during irradiation are negligible     

The application of thiosalts in analysis : A new and more comprehensive scheme of qualitative analysis

The scheme of qualitative analysis based on the formation and decomposition of thiosalts has been enlarged by including within it practically all the basic radicles -which are likely to be met with in the analysis of ores and alloys, etc. Besides the rare elements already included in the original scheme rhodium, ruthenium, osmium, palladium, iridium, gallium, indium, rhenium, tantalum, niobium, germanium, scandium and the rare-earths and alkalis have been fitted into the more comprehensive scheme. An outline of procedures for the separation of metals into groups in the more comprehensive scheme of qualitative analysis is given.     

Simultaneous determination of arsenic, antimony, selenium and tin by gas phase molecular absorption spectrometry after two step hydride generation and preconcentration in a cold trap system

A cold trap system for the simultaneous determination of arsenic, antimony, selenium and tin by continuous hydride generation and gas phase molecular absorption spectrometry is described. The hydride generation is carried out in two steps; first, tin hydride is generated at low acidity and second, arsenic, antimony and selenium hydrides are formed at higher acidity. All the hydrides are collected in a liquid nitrogen cryogenic trap and transported to the flow cell of a diode array spectrophotometer, where molecular absorption spectra are obtained in the 190-250 nm range. Five calibration solutions containing arsenic, antimony, selenium and tin are solved using multiple linear regression analysis. Tests are performed in order to extend the same manifold to other hydrides but no signals are obtained for bismuth, cadmium, lead, tellurium and germanium. Under the optimum conditions found and using the wavelengths of maximum sensitivity (190, 198, 220 and 194 nm), the analytical characteristics of each element are calculated. The detection limits are 0.050, 0.020, 0.12 and 1.1 mug ml(-1) and the RSD values are 3.7, 3.1, 3.5 and 3.0% for As, Sb, Se and Sn, respectively. The method is applied to As, Sb, Se and Sn determination in natural spiked water samples.     

Instrumental determination by neutron activation analysis of trace elements in particulate matter separated from riverine and marine coastal waters of the gulf of Gaeta (Central Italy)

This work presents the results obtained on suspended particulate matter (SPM) collected from the rivers Volturno and Garigliano and from the sea stretch between the mouth of the Volturno river and the Sabaudia lake (Central Tyrrhenian Sea). The elements As, Au, Ca, Ce, Co, Cr, Cs, Eu, Fe, Hf, Hg, La, Lu, Mn, Rb, Sb, Sc, Se, Sm, Ta, Th, W and Yb were determined by instrumental neutron activation analysis. The results show that the element concentrations in SPM tend to be higher in surface than in bottom samples. Also, enrichment factors (EF's) were calculated with respect to Sc assumed as representative of alumino-silicates. Higher values of EF's were found for Zn, As, Se, Sb, Hg, W, and Au.Work partly carried out under the contract No. BIO-B322-I (S) of the Commission of the European Communities.     

Determinations de traces dans les semi-conducteurs par activation neutronique

Résumé On décrit la détermination de traces dans le germanium, le silicium et le sélénium. En appliquant des techniques gamma spectrométriques, précédées ou non de séparations chimiques il est possible de doser les éléments suivants dans (1) germanium: As, Cu, Au, Ga, Zn, Hg, Cr, Sn, Sb, Co, In, Ni, Ir, Se, Sc, Ag, Ta, Hf et U; (2) silicium: P, Au, Sb, Ga, Fe, K, Cr, Mo, Sn, As, Co, In, Zn, Cu, W, Ta, Na, Eu, Sm, La, Sc et T1; (3) sélénium: Cl, Br, I, P, S, Te, Na, K, Cr, Fe, Co, Cu, Zn, Ga, Sc, Ag, Cd, La, W, Au et Tl. Les concentrations et ou limites de détections varient de quelques parties par million à 10⁻³ parties par milliard.     

Evaluation of a tungsten coil atomization-laser-induced fluorescence detection approach for trace elemental analysis

The analytical utility of a tungsten (W)-coil atomization-laser-induced fluorescence (LIF) approach has been evaluated for trace level measurements of elemental chromium (Cr), arsenic (As), selenium (Se), antimony (Sb), lead (Pb), tin (Sn), copper (Cu), thallium (Tl), indium (In), cadmium (Cd), zinc (Zn) and mercury (Hg). Measurements of As, Cr, In, Se, Sb, Pb, Tl, and Sn were performed by laser-induced fluorescence using a single dye laser operating near 460 nm whose output was converted by frequency doubling and stimulated Raman scattering to wavelengths ranging from 196 to 286 nm for atomic excitation. Absolute limits of detection (LODs) of 1, 0.3, 0.3, 0.2, 1, 6, 1, 0.2 and 0.8 pg and concentration LODs of 100, 30, 30, 20, 100, 600, 100, 20, and 80 pg/mL were achieved for As, Se, Sb, Sn, In, Cu, Cr, Pb and Tl, respectively. Determinations of Hg, Pb, Zn and Cd were performed using two-color excitation approaches and resulted in absolute LODs of 2, 30, 5 and 0.6 pg, respectively, and concentration LODs of 200, 3000, 500 and 60 pg/mL, respectively. The sensitivities achieved by the W-coil LIF approaches compare well with those reported by W-coil atomic absorption spectrometry, graphite furnace atomic absorption spectrometry, and graphite furnace electrothermal atomization-LIF approaches. The accuracy of the approach was verified through the analysis of a multielement reference solution containing Sb, Pb and Tl which each had certified performance acceptance limits of 19.6-20.4 μg/mL. The determined concentrations were 20.05 ± 2.60, 20.70 ± 2.27 and 20.60 ± 2.46 μg/mL, for Sb, Pb and Tl, respectively. The results demonstrate that W-coil LIF provides good analytical performance for trace analyses due to its high sensitivity, linearity, and capability to measure multiple elements using a single tunable laser and suggest that the development of portable W-coil LIF instrumentation using compact, solid-state lasers is feasible.     

Determination and geochemical significance of trace elements in Iraqi crude oils using instrumental neutron activation analysis

The trace-element composition of crude oil was studied using instrumental neutron activation techniques and a large-volume high-resolution Ge(Li) detector. A total of 29 elements were determined in oils representing the various producing formations of the Iraqi oil fields. These were: Al, Ar, As, Au, Br, Ca, Cl, Co, Cr, Cu, Eu, Fe, Ga, Hg, K, La, Mn, Mo, Na, Ni, Re, S, Sb, Sc, Se, Sm, V, W and Zn. The significance of these trace elements in the geochemical investigation of crude oil is discussed.     

Elemental content in wheat products of Al-Qusim region, Saudi Arabia using the INAA technique

Wheat is one of the most grown crops in Saudi Arabia. It is grown in various regions of the country. Accurate knowledge of the elemental concentrations in wheat and its products (bran and flour) is of great importance from a nutritional point of view. Wheat samples were obtained from the Al-Qusim region, 300 km northwest of Riyadh, and analyzed. Up to 50 elements (Al, Sb, As, Ba, Br, Cd, Ca, Cs, Cl, Cr, Co, Cu, Ga, Au, Hf, In, I, Ir, Fe, Mg, Mn, Hg, Mo, Ni, K, Rb, Sc, Se, Ag, Na, Sr, Ta, Te, Th, Sn, Ti, W, U, V, Zn, Zr, Ce, Dy, Eu, La, Lu, Nd, Sm, Tb and Yb) were determined in the wheat products. It was observed that the elemental content of bran was much higher than that of white flour.