Temperature dependence of the activation volume in a nonlinear optical polymer: Evidence for chromophore reorientation induced by sub-Tg relaxations

Second harmonic generation (SHG) was used to measure the temperature dependence of the reorientation activation volume of 4-(diethylamino)-4′-nitrotolane (DEANT) in poly(methyl methacrylate) (PMMA). The decay of the SHG signal from films of DEANT/PMMA was recorded at hydrostatic pressures up to 3060 atm and at different temperatures between 25°C below the glass transition temperature to 35°C above it. The activation volume, ΔV*_αβ associated with the long range α-type motion of the polymer remained constant at 213 ± 10 ų between T_g − 25°C and T_g + 10°C. At higher temperatures, ΔV*_αβ decreased linearly with increasing temperature. The activation volume, ΔV*_αβ, associated with short range secondary relaxations was constant over the entire temperature range with a value of 77 ± 10 ų. The data suggest that above T_g chromophore reorientation is coupled to both the long range and local motions of the polymer; whereas, well below T_g chromophore reorientation is closely coupled to the local relaxations of the polymer. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 901–911, 1998     

Synthesis and properties of semi-interpenetrating network based on styrene-acrylonitrile-vinyl acetate terpolymer and zinc acrylate

Semi-Interpenetrating polymer network materials (semi IPNs) have been synthesized from styrene-acrylonitrile-vinyl acetate terpolymer as polymer I and zinc acrylate as polymer II, using divinyl benzene as crosslinking agent for polymer II. The terpolymer was pre-synthesized by a radical polymerization method using AIBN as the radical initiator. The terpolymer has been characterized by IR and elemental analysis. The composition (Sty: AN:VAc) = (0.25:0.50:0.25), the intrinsic viscosity (0.16 dl/g), the softening temperature range (180–185 °C), the glass transition temperature (23 °C) and the thermal stability (up to 300 °C) of the terpolymer were determined. The IPN was characterized by determining its density (1.12 g/cc at 30 °C), molecular weight between crosslinks (M_c = 1469), thermal stability (~ 400 °C), glass transition temperature (41 °C, 78 °C) and two-phase morphology.     

Diffusion and solubility of methane in polyisobutylene

Diffusion coefficients and solubilities of methane in polyisobutylene have been measured at four temperatures between 102 and 188°C. in the pressure range 23–341 atm. Diffusion coefficients extrapolated to atmospheric pressure range from 1.72 × 10^?6 cm.²/sec. at 102°C. to 1.5 × 10^?5 cm.²/sec. at 188°C. corresponding to an activation energy for diffusion of 8.7 ± 0.4 kcal./mole. Solubilities are small, about one molecule of methane for every forty carbon atoms in the polyisobutylene at 300 atm. partial pressure of methane. Solubilities vary little with temperature, but show an apparent minimum between 127 and 188°C. With improved methods of data analysis, diffusion coefficients and solubilities have been recalculated from previously reported studies on nitrogen in branched polyethylene and methane in branched polyethylene, linear polyethylene, and polystyrene. Recalculated diffusion coefficients are essentially the same as those reported previously, but the recalculated solubilities are decreased from 2 to 30%. The solubilities of all five systems show strong deviations from Henry's law, i.e., increases in partial pressure of methane and nitrogen with respect to solubility exceed linearity. The partial pressure (or fugacity)—solubility data may be interpreted in terms of a sorption model in which sorbed molecules are accommodated in widely dispersed, unoccupied volumes or sites in the polymer. An almost equivalent, solution model in which the first sorbed molecules to enter the polymer are accommodated to a large extent in existing volumes in the polymer, with successively sorbed molecules swelling the polymer to a greater extent (i.e., partial molal volume of sorbed molecules, V ₁, increasing with concentration) can also account for these data.     

Preparation and characterization of a nitrogen-doped mesoporous carbon aerogel and its polymer precursor

Nitrogen-containing carbon aerogel was prepared from resorcinol–melamine–formaldehyde (R–M–F) polymer gel precursor. The polymer gel was supercritically dried with CO₂, and the carbonization of the resulting polymer aerogel under nitrogen atmosphere at 900 °C yielded the carbon aerogel. The polymer and carbon aerogels were characterized with TG/DTA–MS, low-temperature nitrogen adsorption/desorption (??196 °C), FTIR, Raman, powder XRD and SEM–EDX techniques. The thermal decomposition of the polymer aerogel had two major steps. The first step was at 150 °C, where the unreacted monomers and the residual solvent were released, and the second one at 300 °C, where the species belonging to the polymer network decomposition could be detected. The pyrolytic conversion of the polymer aerogel was successful, as 0.89 at.% nitrogen was retained in the carbon matrix. The nitrogen-doped carbon aerogel was amorphous and possessed a hierarchical porous structure. It had a significant specific surface area (890 m² g^?1) and pore volume (4.7 cm³ g^?1). TG/DTA–MS measurement revealed that during storage in ambient conditions surface functional groups formed, which were released upon annealing.     

Equilibrium anionic polymerization of β-methoxypropionaldehyde

Anionic polymerization of β-methoxypropionaldehyde (MPA) was carried out in tetrahydrofuran (THF) by using benzophenone–monolithium complex as an initiator. An equilibrium between polymerization and depolymerization was observed at a temperature range of ?90 to ?70°C. From the temperature dependence of the equilibrium monomer concentration, thermodynamic parameters for the polymerization of MPA in THF were evaluated as follows: ΔH_ss = ?4.8 ± 0.2 kcal/mole, ΔH_SS = ?22.4 ± 1.3 cal/mole-deg, and (T_c)_ss = ?59°C. The thermodynamic change upon the conversion of liquid monomer to condensed polymer was computed from both the partial mixing energy of MPA with THF and the linear relationship between the equilibrium volume fraction of MPA monomer and that of the resulting polymer: ΔH_1c = ?4.7 ± 0.2 kcal/mole, ΔS_1c = ?19.5 ± 1.3 cal/mole-deg, and (T_c)_1c = ?35°C.     

Polymerization of Acetylenic Derivatives. XXVI. Polymerization of 9-Ethynylanthracene with Phosphinic,Arsinic, and Stibinic Initiators

9-Ethynylanthracene has been polymerized at 80°C by use of complex phosphinic, arsinic, and stibinic initiators, e. g., NiCl₂′2PPh₃, and the obtained products have been divided into benzene-soluble and benzene-insoluble fractions. It has been shown that the benzene-insoluble polymer has a conjugated polyenic structure while the soluble polymer, with M less than 1500 daltons, contains dihydroanthracene units in the backbone in addition to the conjugated double bonds. It has been found that by using the above initiators the polymers are mainly cis. The cis to trans isomerization has been shown by DTA and DSC measurements to occur between 260 and 290° C.     

The first lonization constant of carbonic acid from 25 to 250°C and to 2000 bar

The apparent first ionization constant of carbonic acid has been determined by conductivity measurements and found to vary from 4.32×10^?7 at 25°C to 1.6×10^?8 at 250°C. The pressure effect to 2000 bar has been measured, and the ratio K_p/K₁ is 7.3 at 25°C and 19 at 250°C. The standard partial molar volume change for the ionization at 1 bar, \(\Delta \bar V_1^0\) , increases from ?27.6 cm³-mole^?1 at 25°C to ?88 cm³-mole^?1 at 250°C. The volume changes are smaller at higher pressures. A linear correlation between \(\Delta \bar V_1^0\) and the partial molar compressibility for the ionization reaction has been noted. A similar correlation exists between the partial molar entropy and volume changes for the reaction.     

Some studies on a polymer from urea

A polymer having the structure of guanidinopolyhydroxynitrile has been produced by heating an equimolar mixture of urea and anhydrous ZnCl₂ in nitrogen at 300°C and 27 atm. The structure has been established from elemental analysis, percentage of nitrogen as primary amine, and ultraviolet and infrared spectra of the polymer and its derivatives. A mechanism of the polymerization based on some experimental evidence has been suggested. Its physical properties have been attributed to its skeletal structure and ring closure by hydrogen bonding. Thermograms reveal that it is stable to 150°C, after which it decomposes slowly till a 75% weight residue is obtained at 575°C with a constant weight plateau extended to 680°C. In acid solvents, protonation occurs at the ? NH₂ group or the azomethine nitrogen atoms, producing polycations. The polyelectrolytic character in acids has been confirmed by viscometric and osmotic studies and the molecules tend to be both coiled up and associated in solutions. [n] in anhydrous formic acid is 0.3636 dl/g. The molecular weights of the polymer and its various fractions range between 39,500 and 25,900. Dielectric constants, dielectric losses, and conductivities of the polymer have also been measured as functions of frequency and temperature and it has been proved that the dispersion is due to dipole polarization. The average energy of the dipole is 1.73 × 10^?2 eV/°K, the intrinsic activation energy for conduction is 0.186 eV, the conductivities being of the order of 2 × 10^?6 to 7 × 10^?7 mho-cm^?1. The polymer is therefore a semiconductor. The number of charge carriers is 2.12 × 10¹⁶/cm², which agrees reasonably well with the value, 6.66 × 10¹⁶, obtained from spin-density calculations from ESR signals.     

Biaspartimide-diamines as Curing Agents for Epoxy Resins

Various 4,4′ -bis(N²-[4-(4-aminophenoxy)phenyl]aspartimido)diphenylmethane-type bisaspartimide-diamines have been used as solventless curing agents for epoxy resins. The thermal curing was performed at 170, 190, and 230°C to give a tough brown polymer. Thermogravimetric analysis of the polymer obtained showed thermal stability up to 330°C and char yields of 45% in N₂ at 800°C and 12% in air at 700°C. The thermal curing reaction was monitored using FT-IR. The synthesized polymers are useful for making composites, laminates, and adhesives.     

Auto-acceleration of radical polymerization rate in polymerization of styrene under the condition of predominant transfer

Styrene was polymerized at 20°C for 252 days in the presence of 2,2′-azobis(isobutyronitrite) azobis(isobutyronitrile) (AIBN). When [AIBN]_σ = 0.268 mmol l⁻¹, the instantaneous weight-average degree of polymerization (140,000) of the polymer formed is independent of conversion x between 0.05 and 0.60. This independence shows predominant transfer to monomer. Auto-acceleration of polymerization starts at about x = 0.02. In order to explain this auto-acceleration, an equation derived previously for the relationship between termination rate, free volume and volume fraction of polymer is applied to the kinetic data obtained under the condition of predominant transfer to monomer. It is concluded that polymer molecules may move by reptation and the mobility of segments decreases with decreasing free volume.     

Thermal behavior of polytriazole films: A thermal analysis study

The thermal behavior of poly(1,3-phenyl-1,4-phenyl)-4-phenyl-1,2,4-triazole has been investigated using different scanning calorimetry (DSC) and thermogravimetry (TG). Processes are studied for this thermally stable polymer that take place between 200 and 500°C. While the polycondensation reaction product in powder from appeared to be partially crystalline, films prepared by casting from a formic acid solution appeared to be completely amorphous. A thermal treatment between T_g(～ 270°C) and T_m(～ 430°C) can introduce crystallinity in the films because of the polymer's ability to cold crystallize. The cold crystallization temperature T_c seems to be dependent on the preparation history of the solid polymer phase. Thermal annealing of the films just below T_g does not introduce crystallinity but inhibits subsequent cold crystallization at higher temperatures. Crystallization upon cooling from the crystalline melt has not been observed either. At temperatures just above the crystalline melting point the polymer starts to decompose in an exothermic reaction.     

Novel Crosslinked Guest-Host System with Stable Second-Order Nonlinearity

Abstract

An epoxy-based nonlinear optical (NLO) polymeric material incorporating 4-(4′-nitrophenylazo) phenylamine has been synthesized and subsequently functionalized with acryloyl groups. A glass transition temperature (T ₈)of 108°C and a degradation temperature (air) of 251°C were recorded. After crosslinking at 160°C for 2 hours, the T ₈ of the polymer increased to 146°C. In order to increase the nonlinear optical chromophore concentration and the crosslinking density, the crosslink-able NLO dye, 2,4-acryloyloxy (4′-phenylazo nitrobenzene), was processed and poled in this epoxy-based NLO material matrix in a manner similar to a typical guest-host system, and thermally crosslinked under the above condition in the poled phase. The crosslinked guest-host material was found to be amorphous with a T ₈ of approximately 132°C. It also exhibits a second-order nonlinear optical coefficient d ₃₃ of 14.14 pm/V at a maximum doping level of 33% by weight of the NLO dye, and retains 93% of its original d ₃₃ value after being subjected to thermal treatment at 100°C for 168 hours. The behavior of the crosslinked polymer and the crosslinked guest-host polymer is discussed.     

Gas permeability of a new silicone ring polymer: Isotactic poly(phenyl silsesquioxane)

The permeability of isotactic poly(phenyl silsesquioxane) (PPSQ) to O₂ and N₂ at 25.0°C and to CO₂ and CH₄ at 35.0°C was measured at low pressures by the “time-lag” method. PPSQ is a glassy silicone polymer with an 8-atom ring structure of alternating Si and O atoms. The CO₂/CH₄ selectivity of PPSQ is markedly higher than that of other silicone polymers, whereas its O₂/N₂ selectivity appears to be only slightly higher. PPSQ is not as effective a “molecular sieve” as would be expected from its ring structure, possibly because its relatively large mean interchain distance suggests that this polymer has a large mean free volume.     

Hydrolytic degradation and thermooxidative stability of polyimides based on 3,5-diaminodiphenyl oxide and 2-methyl-3,5-diaminodiphenyl sulfide

For a number of new polyimides prepared from 3,5-diaminodiphenyl oxide, 2-methyl-3,5-diaminodiphenyl sulfide, and various dianhydrides of aromatic tetracarboxylic acids, the hydrolytic stability in DMF and 96% H₂SO₄ and the thermooxidative stability in the bulk have been studied. Hydrodynamic techniques have been employed to determine the molecular parameters of these polymers at various stages of degradation. It has been shown that the polymers under study form stable solutions in DMF but turn out to be unstable in 96% H₂SO₄ even at room temperature. Degradation accompanies dissolution of the polymer. The correlation between the chemical structure of polymer molecules and their hydrolytic stability in both solvents has been established. It has been demonstrated that the majority of the said polyimides are stable in the solid state at temperatures up to 400°C and marked degradation begins only above 500°C.     

Interactive Thermal Effects on Metal–Organic Framework Polymer Composite Membranes

Polymeric membranes are important tools for intensifying separation processes in chemical industries, concerning strategic tasks such as CO₂ sequestration, H₂ production, and water supply and disposal. Mixed‐matrix and supported membranes have been widely developed; recently many of them have been based on metal–organic frameworks (MOFs). However, most of the impacts MOFs have within the polymer matrix have yet to be determined. The effects related to thermal behavior arising from the combination of MOF ZIF‐8 and polysulfone have now been quantified. The catalyzed oxidation of the polymer is strongly affected by the MOF crystal size and distribution inside the membrane. A 16 wt % 140 nm‐sized ZIF‐8 loading causes a 40 % decrease in the observed activation energy of the polysulfone oxidation that takes place at a temperature (545 °C) 80 °C lower than in the raw polymer (625 °C).     

Matched ring diblock and linear triblock copolymers in dilute solution

A unique diblock copolymer ring and its linear triblock copolymer precursor composed of polystyrene and polydimethylsiloxane have been characterized by static and dynamic light scattering in dilute solution. The measurements were carried out with cyclohexane as the solvent over a temperature range of 12–35°C. Cyclohexane has the useful property that it is nearly isorefractive with the PDMS so that the PDMS block segments are invisible to the light-scattering technique and it is a theta solvent for polystyrene at 34.5°C. The block polymers in this work contain 35.1 wt % of styrene as determined by proton NMR. In the linear triblock polymer, the polystyrene is the center block with PDMS blocks on each side. Static light scattering measurements give 4.31 × 10⁴ for the average molecular weight of the whole polymer. Light scattering also shows that the apparent theta temperature for the linear triblock is shifted by 15°C to a value of 20°C at which point the second virial coefficient drops sharply and phase separation begins to induce aggregation. The diblock ring, however, shows a strongly positive second virial coefficient and no aggregation even at 12°C which is the limit of these experiments. The diffusion coefficients of cyclic diblock (D_c) and linear triblock copolymer (D₁) are measured by dynamic light scattering. The ratio of diffusion coefficients of cyclic and linear copolymers at 14.9°C and 30°C are D_c/D_l = 1.13 and 1.107 respectively. These compare well with prediction of 1.18 for this ratio from consideration of the hydrodynamics of matched linear and cyclic polymer chains. Dynamic light scattering quantitatively confirms that the linear copolymer experiences a solvent quality change near 20°C but the cyclic polymer remains in good solvent over the entire experimental temperature range. © 1993 John Wiley & Sons, Inc.     

Mechanical properties of composite heterogeneous gels

Composites with a matrix of poly(2-hydroxyethyl methacrylate) (PHEMA) and 10% by volume of various crosslinked PHEMA polymer fillers (prepared by copolymerization with 0.1, 0.4, 1.0, and 20.0% by weight of ethylenedimethacrylate) of particle size about 1 μm were prepared. Some polymer matrixes were prepared from soluble branched PHEMA (Hydron S), and others by copolymerization, in the presence of the filler with 0.4 and 1.0% of ethylenedimethacrylate as a crosslinking agent. In the case of the uncrosslinked matrix, a linear polymer–crosslinked polymer system, resulted; in the case of the crosslinked matrix, a composite heterogeneous network was formed (in the latter case, the particles of the filler were swollen with monomer during the crosslinking polymerization). Stress–strain, equilibrium, and ultimate characteristics were measured at 3, 10, 25, 40, 60, and 80°C on samples swollen to equilibrium in water (T_g ≈ ?50°C) and at 80, 110, and 140°C on dry samples (T_g ≈ 100°C). Depending on experimental conditions, above all on the distance from the main transition region and on whether the polymer is dry or swollen, it was found that the measured hydrophilic composite systems behaves as a filled system (with the polymer filler acting mostly as solid particles, irrespective of the crosslink density) or as a system with crosslink density fluctuations (where both networks, the matrix and the filler, contribute roughly additively to the properties of the system), or finally as defect heterogeneous systems (where the properties depend primarily on the character of the polymer–filler interface).     

Unusual effect of molecular weight and concentration on thermoresponsive behaviors of well‐defined water‐soluble semirigid polymers

A series of water‐soluble semirigid thermoresponsive polymers with well‐defined molecular weights based on mesogen‐jacketed liquid crystal polymers (MJLCPs), poly[bis(N‐hydroxyisopropyl pyrrolidone) 2‐vinylterephthalate] (PHIPPVTA) have been synthesized via reversible addition fragmentation chain transfer (RAFT) polymerization. Dynamic light scattering (DLS) revealed that the novel monomer and polymers have thermoresponsive properties with cloud point in the range between 10 and 90 °C. The cloud point was increased by 56.2 °C when the polymer molecular weight increased from 0.47 × 10⁴ g mol^?1 to 3.69 × 10⁴ g mol^?1. In addition, the cloud point of PHIPPVTA was decreased by 18.8 °C with the increase of polymer concentration from 5 to 10 mg mL^?1. A slight increase (0.1–3.5 °C) of cloud point has been observed after knocking off the end‐groups of PHIPPVTA. Moreover, the cloud point of polymer increased with increasing of its molecular weight with or without the trithiocarbonate end‐groups, which showed the opposite trend comparing with other thermoresponsive polymers with flexible backbones. These polymers show a dramatic solvent isotopic effect that the cloud point in D₂O was lower than in H₂O. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis,characterization and properties of a soluble polymer with a poly(phenylenevinylene) structure

Soluble poly(2,5-dialkoxy-1,4-phenylenevinylene) has been prepared via Stille coupling reaction between 2,5-dialkoxy-1,4-diiodobenzene and E-1,2-bis(tributylstannyl)-ethene in the presence of palladium complexes. Characterization of this material by means of ¹H and ¹³C nuclear magnetic resonance (NMR), ultraviolet/visible (UV/VIS) and infrared (IR) spectra is described. Molecular weights, determined by means of gelpermeation chromatography (GPC) analysis and referred to standard polystyrene, were in the range number-average molecular weights M _n = 2061–2544 and weight-average molecular weights M _w = 3347–3878. X-ray diffraction (XRD) analysis of the polymer showed semicrystalline structure. T_g = 57°C, transition to a stable smectic mesophase at 115°C and clearing point at 210°C were revealed by differential scanning calorimetry analysis, optical microscopy observation and XRD of the annealed polymer.     

Effect of pressure and temperature on chromophore reorientation in a side-chain nonlinear optical polymer

Second harmonic generation (SHG) was used to measure the temperature dependence of the reorientation activation volume of the side-chain copolymer poly(disperse red 1 methacrylate-co-methyl methacrylate) (DR1-MMA). The decay of the SHG signal from poled films of DR1-MMA was recorded at hydrostatic pressures up to 3060 atm and at different temperatures between 25°C below the glass transition temperature (T_g) to 35°C above it. The activation volume, ΔV^*, decreased with increasing temperature. The data suggests that the coupling between chromophore reorientation and the long-range motion of the polymer is stronger for the DR1-MMA side-chain system than in previously measured guest–host systems. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2793–2803, 1998