Analysis of the resistive switching behaviors of vanadium oxide thin film

We demonstrate the polarization of resistive switching for a Cu/VOx/Cu memory cell.The switching behaviors of Cu/VOx/Cu cell are tested by using a semiconductor device analyzer(Agilent B1500A),and the relative micro-analysis of I-V characteristics of VOx/Cu is characterized by using a conductive atomic force microscope(CAFM).The I-V test results indicate that both the forming and the reversible resistive switching between low resistance state(LRS) and high resistance state(HRS) can be observed under either positive or negative sweep.The CAFM images for LRS and HRS directly exhibit evidence for the formation and rupture of filaments based on positive or negative voltage.The Cu/VOx/Cu sandwiched structure exhibits reversible resistive switching behavior and shows potential applications in the next generation of nonvolatile memory.     

氧化钒薄膜的微结构及阻变特性研究

采用射频反应溅射法于室温下在Cu/Ti/SiO₂/Si基底上制备了氧化钒薄膜. X-射线衍射、X射线光电子能谱分析仪及原子力显微镜结果表明, 室温下制备的氧化钒薄膜除微弱的V₂O₅ (101)和V₂O₃ (110)峰外, 没有明显的结晶取向, 是VO₂, V₂O₅, V₂O₃及VO的混合相薄膜, 且薄膜表面颗粒大小均匀, 表面均方根粗糙度约为1 nm. 采用半导体参数分析仪对薄膜的电开关特性进行测试. 结果表明薄膜具有较低的开关电压(V_Set<1 V, V_Reset<-0.5 V), 并且具有稳定的可逆开关特性. 薄膜从低阻态转变为高阻态的电流(I_Reset)随限流的增大而增大.通过高低阻态时I-V对数曲线的拟合(高阻态斜率>1, 低阻态斜率=1), 认为Cu离子在薄膜中扩散形成的导电细丝是该体系发生电阻转变的主要机制. 关键词： 氧化钒薄膜 电阻开关 电阻式非挥发存储器 导电细丝     

电泳沉积法制备的Zn1-xCxO薄膜的结构及阻变性能

采用电泳沉积法在FTO导电玻璃基片上制备Zn_1-xCu_xO薄膜,并对其微观结构、光致发光谱、伏安特性、保持特性和转换电压分布进行探讨。PL谱表明,Cu掺杂在禁带中引入深受主能级,降低氧空位浓度,导致ZnO薄膜的紫外发光、蓝光发光和绿光发光峰强度降低。所得薄膜的晶粒细小、致密、均匀,具有稳定的双极性阻变特性,开关比R_off/R_on最高达到10⁵,其低阻态（LRS）和高阻态（HRS）的阻变机理分别符合欧姆定律和空间电荷限制传导理论。器件经100次循环测试后开关比无明显变化,呈现出较为良好的抗疲劳特性。Cu掺杂对LRS影响不大,但显著改善了HRS的分散性以及转换电压V_SET的分散性。当Cu掺杂量x=0.04时,器件表现出良好的综合性能：R_off≈10⁶ Ω,R_off/R_on≈10⁴,V_SET介于0.4~3.03 V之间。     

Charge transport and bipolar switching mechanism in a Cu/HfO_2/Pt resistive switching cell

Bipolar resistance switching characteristics are investigated in Cu/sputtered-HfO_2/Pt structure in the application of resistive random access memory(RRAM).The conduction mechanism of the structure is characterized to be SCLC conduction.The dependence of resistances in both high resistance state(HRS) and low resistance state(LRS) on the temperature and device area are studied.Then,the composition and chemical bonding state of Cu and Hf at Cu/HfO_2 interface region are analyzed by x-ray photoelectron spectroscopy(XPS).Combining the electrical characteristics and the chemical structure at the interface,a model for the resistive switching effect in Cu/HfO_2/Pt stack is proposed.According to this model,the generation and recovery of oxygen vacancies in the HfO_2 film are responsible for the resistance change.     

Intrinsic memory characteristic of polycrystalline ZnTe film originating from Mott variable range hopping conduction

The resistive switching characteristics of Au/ZnTe/ITO structure with polycrystalline ZnTe film as resistive switching layer is investigated. Macroscopically, 100 bipolar switching cycles under the direct current (dc) voltages were carried out and the conduction states can retain for several hours. Microscopically, reading and writing operations can be achieved on ZnTe film with Au top electrode replaced by conductive Atomic Force Microscopy (c-AFM) tip. The I–V characteristic in low resistance state (LRS) is linear in the whole range of voltage. The I–V characteristic in high resistance state (HRS) is linear in the low voltage while it obeys Schottky emission in the high voltage, and Schottky barrier height is symmetric in the positive and negative voltage. During linear I–V characteristic voltage range, the electrons transport between adjacent point defects via Mott variable range hopping. The higher hopping distance and higher activation energy in HRS contribute to the higher resistance value in HRS compared with LRS. Impedance spectroscopy in HRS and LRS both behave as a semicircle, which accords with the semiconductor-like characteristic of conductive point defects. Photoluminescence (PL) spectroscopy indicates the decisive role of deep level defects in conduction. This study confirms the intrinsic resistive switching characteristic of ZnTe film and provides a new choice for intrinsic non-oxides material in nonvolatile memory application.     

Coexistence of nonvolatile unipolar and volatile threshold resistive switching in the Pt/LaMnO3/Pt heterostructures

Coexistence of nonvolatile unipolar and volatile threshold resistive switching is observed in the Pt/LaMnO₃ (LMO)/Pt heterostructures. The nonvolatile unipolar memory is achieved by applying a negative bias, while the volatile threshold resistive switching is obtained under a positive bias. Additionally, the pristine low resistance state (LRS) could be switched to high resistance state (HRS) by the positive voltage sweeping, which is attributed to the conduction mechanism of Schottky emission. Subsequently, the insulator-to-metal transition in the LMO film due to formation of ferromagnetic metallic phase domain contributes to the volatile threshold resistive switching. However, the nonvolatile unipolar switching under the negative bias is ascribed to the formation/rupture of oxygen-vacancy conducting filaments. The simultaneously controllable transition between nonvolatile and volatile resistance switching by the polarity of the applied voltage exhibits great significance in the applications of in-memory computing technology.     

Resistive switching functional quantum-dot light-emitting diodes

This study demonstrates quantum-dot light-emitting diodes (QD-LEDs) with a function of resistive switching memory, capable of on/off operation at the same driving current depending on reset/set state. The QD-LEDs were fabricated by spin-coating process and experienced two different annealing conditions, which yielded defective or less-defective V₂O_5–x layer. One of the annealing conditions produced QD-LEDs with the unusual electrical behaviors of negative differential resistance (NDR), capacitance oscillation, and voltage–current hysteresis curves, signifying so-called resistive switching characteristics. X-ray and ultraviolet photoelectron spectroscopies were used to examine the chemical state of the differently annealed V₂O_5–x layers. The less stoichiometric V₂O_5–x layer was found to be responsible for the resistive switching behaviors of the NDR and the low and high resistance states (LRS and HRS, respectively). We discuss the LRS/HRS of V₂O_5–x for resistive switching in terms of a conductive filament effect, induced by microstructural changes caused by oxygen drift and vacancy annihilation processes in the high defect density V₂O_5–x layer.     

Characteristics of the bipolar resistive switching behavior in memory device with Au/ZnO/ITO structure

In this work, reproducible and stable bipolar resistive switching behavior without the requirement of forming process is observed in the memory device with Au/ZnO/ITO structure. It shows a high R_on/R_off ratio, where R_on and R_off are the resistance at low resistance state (LRS) and high resistance state (HRS), respectively. The dominated transport mechanisms for LRS and HRS are related to space charge limited current and Ohmic behavior, respectively. This bipolar resistive behavior is attributed to the formation and rupture of conducting filaments which are constructed with oxygen vacancies. The Au/ZnO/ITO device discussed in this work shows huge potential applications in the next generation nonvolatile memory field.     

Bipolar resistive switching in BiFe_(0.95)Zn_(0.05)O_3 films

Bipolar resistive switching is studied in BiFe0.95Zn0.05O3 films prepared by pulsed laser deposition on （001） SrTiO3 substrate, with LaNiO3 as the bottom electrode, and Pt as the top electrode. Multiple steps of resistance change are ob- served in the resistive switching process with a slow voltage sweep, indicating the formation/rupture of multiple conductive filaments. A resistive ratio of the high resistance state （HRS） to the low resistance state （LRS） of over three orders of mag- nitude is observed. Furthermore, the conduction mechanism is confirmed to be space-charge-limited conduction with the Schottky emission at the interface with the top Pt electrodes in the HRS, and Ohmic in the LRS. Impedance spectroscopy demonstrates a conductive ferroelectric/interfacial dielectric 2-layer structure, and the formation/rupture of the conductive filaments mainly occurs at the interfacial dielectric layer close to the top Pt electrodes.     

Fully room‐temperature‐fabricated TiN/TaOx/Pt nonvolatile memory devices

The reliable resistive switching properties of TiN/TaO_x/Pt structures fabricated with a fully room‐temperature process are demonstrated in this letter. The devices exhibited a low operation voltage of 0.6 V as well as good endurance up to 10⁵ cycles. No data loss was reported upon continuous readout for more than 10⁴ s at 125 °C. Multilevel storage is feasible due to the dependence of the low resistance state (LRS) on the initial “SET” (switch from high to low RS) compliance current. The values of LRS showed no dependence on the size of the device, which correlated with the localized conductive filament mechanism. This nonvolatile multilevel memory effect and the fully room‐temperature fabrication process make the TiN/TaO_x/Pt memory devices promising for future nonvolatile memory application. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Investigation of resistive switching behaviours in WO3-based RRAM devices

In this paper, a WO₃-based resistive random access memory device composed of a thin film of WO₃ sandwiched between a copper top and a platinum bottom electrodes is fabricated by electron beam evaporation at room temperature. The reproducible resistive switching, low power consumption, multilevel storage possibility, and good data retention characteristics demonstrate that the Cu/WO₃/Pt memory device is very promising for future nonvolatile memory applications. The formation and rupture of localised conductive filaments is suggested to be responsible for the observed resistive switching behaviours.     

Effect of AlN layer on the resistive switching properties of TiO2 based ReRAM memory devices

The present study reports the resistive switching behaviour in Titanium Dioxide (TiO₂) material, with possible implementations in non volatile memory device. The Cu/TiO₂/Pt memory device exhibit uniform and stable bipolar resistive switching behaviour. The current-voltage (I-V) analysis shows two discrete resistance states, the High Resistance State (HRS) and the Low Resistance State (LRS). The effect of an additional AlN layer in the resistive memory cell is also investigated. The Cu/TiO₂/AlN/Pt device shows a multilevel (tri-state) resistive switching. Multilevel switching is facilitated by ionic and metallic filament formation, and the nature of the formed filaments is confirmed by performing a resistance vs. temperature measurement. The bilayer device shows improved reliability over the single layer device. The formation of high thermal conductive interfacial oxy-nitride (AlON) layer is the main reasons for the enhancement of resistive switching properties in Cu/TiO₂/AlN/Pt cell. The performance of device was measured in terms of endurance and retention, which exhibits good endurance over 10⁵ cycles and long retention time of 10⁵ s at 125 °C. The above result suggests the feasibility of Cu/TiO₂/AlN/Pt devices for multilevel non volatile ReRAM application.     

Unipolar resistive switching properties of amorphous Pr0.7Ca0.3MnO3 films grown on a Pt/Ti/SiO2/Si substrate

Amorphous Pr_0.7Ca_0.3MnO₃ (APCMO) films were grown on a Pt/Ti/SiO₂/Si (Pt–Si) substrate at temperatures below 500 °C and the Pt/APCMO/Pt–Si device showed unipolar resistive switching behavior. Conduction behavior of the low resistance state (LRS) of the Pt/APCMO/Pt–Si device followed Ohm's law, and the resistance in LRS was independent of the size of the device, indicating that the conduction behavior in LRS can be explained by the presence of the conductive filaments. On the other hand, the resistance in the high resistance state (HRS) decreased with increasing the device size, and the conduction mechanism in the HRS was explained by Schottky emission.     

Resistive switching behavior and mechanism of room-temperature-fabricated flexible Al/TiS2-PVP/ITO/PET memory devices

The mixture of two-dimensional (2D) TiS₂ nanoflakes and polyvinylpyrrolidone (PVP) exhibits a nonvolatile, bipolar resistive switching behavior with a low resistance state (LRS)/high resistance state (HRS) current ratio of ～10² in the devices with a flexible Al/TiS₂-PVP/indium tin oxide (ITO)/polyethylene terephthalate (PET) structure. The polymer-assistant liquid-phase exfoliation of 2D nanoflakes from TiS₂ bulk material is processed in low-boiling solvent. And the fabrication process of these devices is performed entirely at room temperature. Such an energy-saving and scalable production process indicates a huge potential of large-scale industrial application. The AFM and TEM characterizations showed that the exfoliated 2D TiS₂ are flakes at micrometer scale with a layer-number of mostly 7 or 8. Both the HRS and the LRS can be kept for more than 10⁴ s. The endurance of devices was obtained over 100 direct current (DC) sweeping cycles with remarkable separations between different resistive states. The distributions of writing (set) and erasing (reset) voltages show that set and reset voltages are small (<2 V). Also, the resistive switching characteristics of the devices are stable during 1000 bending cycles. The switching behavior is explained by the thinning and recovery of Schottky barriers within devices.     

Nonvolatile Resistive Switching and Physical Mechanism in LaCrO_3 Thin Films

Polycrystalline LaCrO_3(LCO) thin films are deposited on Pt/Ti/SiO_2/Si substrates by pulsed laser deposition and used as the switching material to construct resistive random access memory devices. The unipolar resistive switching(RS) behavior in the Au/LCO/Pt devices exhibits a high resistance ratio of ~104 between the high resistance state(HRS) and low resistance state(LRS) and exhibits excellent endurance/retention characteristics.The conduction mechanism of the HRS in the high voltage range is dominated by the Schottky emission, while the Ohmic conduction dictates the LRS and the low voltage range of HRS. The RS behavior in the Au/LCO/Pt devices can be understood by the formation and rupture of conducting filaments consisting of oxygen vacancies,which is validated by the temperature dependence of resistance and x-ray photoelectron spectroscopy results.Further analysis shows that the reset current I_R and reset power P_R in the reset processes exhibit a scaling law with the resistance in LRS(R_0), which indicates that the Joule heating effect plays an essential role in the RS behavior of the Au/LCO/Pt devices.     

Nonvolatile bipolar resistance switching effects in multiferroic BiFeO3 thin films on LaNiO3-electrodized Si substrates

We report on reversible bipolar resistance switching effects in multiferroic BiFeO₃ thin films without electroforming. The BiFeO₃ thin films with (110) preferential orientation were prepared on LaNiO₃-electrodized Si substrates with a Pt/BiFeO₃/LaNiO₃ device configuration. The resistance ratio of high resistance state (HRS) to low resistance state (LRS) of the devices was as high as three orders of magnitude. The dominant conduction mechanisms of LRS and HRS were dominated by ohmic behavior and trap-controlled space charge limited current, respectively. The resistance switching mechanism of the devices was discussed using a modified Schottky-like barrier model taking into account the movement of oxygen vacancies.     

基于Cu/SiO_x/Al结构的阻变存储器多值特性及机理的研究

采用氧化硅材料构建了Cu/SiOx/Al的三明治结构阻变存储器件.用半导体参数分析仪对其阻变特性进行测量,结果表明其具有明显的阻变特性,并且通过调节限制电流,得到了四个稳定的阻态,各相邻阻态的电阻比大于10,并且具有良好的数据保持能力.在不同温度条件下对各个阻态进行电学测试及拟合,明确了不同阻态的电子传输机理不尽相同:阻态1和阻态2为欧姆传导机制,阻态3为P-F(Pool-Frenkel)发射机制,阻态4为肖特基发射机制.根据电子传输机制,建立了铜细丝导电模型并对Cu/SiOx/Al阻变存储器件各个阻态的电致阻变机制进行解释.     

Resistive switching mechanism of Ag/ZrO2:Cu/Pt memory cell

Resistive switching mechanism of zirconium oxide-based resistive random access memory (RRAM) devices composed of Cu-doped ZrO₂ film sandwiched between an oxidizable electrode and an inert electrode was investigated. The Ag/ZrO₂:Cu/Pt RRAM devices with crosspoint structure fabricated by e-beam evaporation and e-beam lithography show reproducible bipolar resistive switching. The linear I?CV relationship of low resistance state (LRS) and the dependence of LRS resistance (R _ON) and reset current (I _reset) on the set current compliance (I _comp) indicate that the observed resistive switching characteristics of the Ag/ZrO₂:Cu/Pt device should be ascribed to the formation and annihilation of localized conductive filaments (CFs). The physical origin of CF was further analyzed by transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDS). CFs were directly observed by cross-sectional TEM. According to EDS and elemental mapping analysis, the main chemical composition of CF is determined by Ag atoms, coming from the Ag top electrode. On the basis of these experiments, we propose that the set and reset process of the device stem from the electrochemical reactions in the zirconium oxide under different external electrical stimuli.     

Improved resistive switching performance in Cu-cation migrated MoS2 based ReRAM device incorporated with tungsten nitride bottom electrode

The resistive switching characteristics of sputtered deposited molybdenum disulphide (MoS₂) thin film has been investigated in Cu/MoS₂/W₂N stack configuration for Resistive Random Access Memory (ReRAM) application. The benefits of incorporating tungsten nitride (W₂N) as a bottom electrode material were demonstrate by stability in operating voltages, good endurance (10³ cycles) and long non-volatile retention (10³?s) characteristics. Resistive switching properties in Cu/MoS₂/W₂N structure are induced by the formation/disruption of Cu conducting filaments in MoS₂ thin film. Ohmic law and space charge limited current (SCLC) are observed as dominant conduction mechanism in low resistance state (LRS) and high resistance state (HRS) respectively. This study suggests the application of MoS₂ thin films with W₂N bottom electrode for next generation non-volatile ReRAM application.