孔耦合自由电子激光振荡器光场横向结构特性

 孔耦合输出对自由电子激光(FEL)振荡器腔内光场的横向结构有很大的影响, 在输出镜上横模之间发生很复杂的耦合转换。基于中物院远红外自由电子激光振荡器, 研究了 孔输出波导 FEL的数值模拟, 对孔耦合及其引起的腔内光场的变化给以特别的注意, 依据数 值结果, 分析了孔耦合FEL光场横向结构的特性。     

高斯反射率输出耦合镜和恒输入功率技术在（Nd，Ce）：YAG激光器中的应用

本文论述高斯反射率输出耦合镜非稳腔设计中应注意的一些问题，将恒输入功率技术应用于高重频高功率单横模（Ｎｄ，Ｃｅ）：ＹＡＧ激光器，当重频改变时仍旧保持单横模输出。     

横模谱方法与孔耦合FEL振荡器数值模拟

 横模谱方法广泛应用于自由电子激光振荡器数值模拟。以孔耦合波导FEL振荡器的模型问题为例,通过对数值结果的分析和比较,说明横模谱方法的应用效果取决于诸多物理因素,在孔耦合情形下,主要取决于孔耦合效应及其引起的腔内光场横模结构的发展变化。     

波导FEL振荡器的孔耦合输出特性

波长５００μｍ的远红外自由电子激光振荡器，是由平面被导和两个对称金属柱面镜组成的半封闭光腔．由于反射镜具有反射率，在下游镜的轴上开一个半径为Ｒｈ的圆孔来输出功率．孔耦合输出是一种简单、有效的输出方式，并可以广谱输出．缺点是抽取率随波长变化，计算很复杂．本文给出了用三维程序数值模拟结果．给出了腔内功率，输出功率，抽取率及腔镜边缘的衍射损失随小孔半径的变化．结果表明，选取适当的孔径，既可以有效地输出功率，又能保持较高的腔内功率和较纯净的腔模．     

激光二极管端面抽运室温Tm,Ho:YLF连续固体激光器

报道了激光二极管端面抽运Tm，Ho：YLF固体激光器的输出特性.室温下，选用不同透过率的输出耦合镜进行了实验研究，确定了最佳输出耦合镜透过率为2%. 利用小孔扫描的方法，得到了激光远场的光强分布，证明激光为基横模输出，并且给出了热焦距随抽运功率的变化关系.通过在激光谐振腔内插入两个固体Fabry-Perot标准具的方法，获得了2μm激光的单频输出，阈值功率为250mW，在抽运功率为2.8W时，单频输出功率为118mW.此单频激光器可用作激光振荡器和激光放大器的种子源. 关键词： 激光光学 激光二极管 Tm Ho:YLF固体激光器 单频     

孔耦合自由电子激光振荡器的数值模拟方法

针对孔耦合波导自由电子激光振荡器腔内光场横向特性,应用有限元法于慢变光场方程,并对输出腔镜上孔耦合过程加以较准确的描述,而后通过对数值结果的分析比较,说明这一模拟方法较好地描述了孔耦合引起的腔内光场横向结构的变化发展特性,改善了模拟结果。     

970 nm高功率光栅外腔可调谐半导体激光器

宽条形半导体激光器广泛应用于激光泵浦、激光加工等领域。针对宽条型半导体激光器输出光谱宽、调谐范围小的问题,采用衍射效率分别为28%和55%的反射式衍射光栅作为反馈元件构建了宽条形970 nm波长光栅外腔半导体激光器。研究了Littrow结构激光器参数对其性能（调谐范围、功率、阈值电流、线宽）的影响。实验结果表明,通过结构优化可得到窄线宽可调谐激光输出,适当地提高温度和使用较高衍射效率的光栅可增加激光器调谐范围,并且较高衍射效率的光栅可降低激光器的阈值电流。基于S偏振入射方式的光栅外腔激光器最大可实现27.87 nm的波长调谐范围,光谱线宽压窄至0.2 nm,输出功率可达1.11 W。     

猫眼激光谐振腔横模选择特性研究

将猫眼逆向器作为激光谐振腔的一个腔镜组成猫眼谐振腔。介绍了猫眼逆向器的结构,阐述了猫眼逆向器中凸透镜和凹面镜的间距改变时猫眼曲率半径的相应变化,并通过有效地控制该间距来选择激光横模,从而保证基横模输出。在激光谐振腔衍射积分方程的基础上,运用牛顿柯特斯数学方法,对不同参量下的猫眼激光谐振腔的横模状况进行分析,得出了各阶横模对应的特征值和功率损耗,计算出保证基横模输出的参量,并与实验对比,得到了一致的结论,为激光器的横模选择和控制提供了一种简便易行的新方法。     

基于光纤布拉格光栅对的双波长线形腔掺铒光纤激光器设计与优化

基于光纤布拉格光栅对（DFBGs）的双波长线形腔光纤激光器利用偏振烧孔效应实现双波长激光稳定输出的研究颇多,但有关3 dB光纤环形镜（FLM）与光纤布拉格光栅（FBG）构成腔镜或仅FBG构成腔镜,以及DFBGs的选择对其激光输出性能[光信噪比（OSNR）、斜率效率及稳定性等]的影响的研究很少。本文实验首先在双波长线形腔掺铒光纤激光器中比较了3 dB FLM与FBG构成腔镜和仅FBG构成腔镜的双波长激光的输出性能,结果表明,仅FBG构成腔镜的输出性能优于3 dB FLM与FBG构成腔镜的输出。其次在仅FBG构成腔镜的线形腔中对低反射率FBG（输出镜）反射率相同与不同时的输出性能进行了对比,研究表明,低反射率FBG的反射率相同时双波长激光输出具有较高的OSNR、斜率效率和稳定性。接着改变构成腔镜的两对FBG的中心波长间隔分别为4、8、12 nm,研究表明,中心波长间隔越大输出越稳定,OSNR越高,但激光器的斜率效率有所降低。最后在室温环境下实现了两个激光波长分别为1550 nm和1562 nm、OSNR分别为50.24 dB和51.19 dB左右、中心波长变化分别小于0.030 nm和0....     

端面泵浦掺Yb3+双包层光纤激光器

从双包层光纤激光器的速率方程出发，得到了光纤中泵浦光与激光的功率分布、输出功率与泵浦功率的关系、腔镜反射率及光纤长度对输出功率的影响。研究结果表明：输出激光功率与光纤长度及后腔镜反射率有很强的依赖关系，存在一个输出功率最大的最佳光纤长度。后腔镜反射率越大，输出激光功率越小；当光纤长度较短时，在输出端放置反射镜使泵浦光高反射，可以提高输出功率和效率。通过对端面泵浦掺Yb3+双包层光纤激光器进行理论分析和实验研究，得到输出激光的中心波长为1088.3nm，斜率效率为33.7%，最大输出功率为1.75W。     

Short T2 contrast with three-dimensional ultrashort echo time imaging

There is increasing interest in imaging short T2 species which show little or no signal with conventional magnetic resonance (MR) pulse sequences. In this paper, we describe the use of three-dimensional ultrashort echo time (3D UTE) sequences with TEs down to 8 μs for imaging of these species. Image contrast was generated with acquisitions using dual echo 3D UTE with echo subtraction, dual echo 3D UTE with rescaled subtraction, long T2 saturation 3D UTE, long T2 saturation dual echo 3D UTE with echo subtraction, single adiabatic inversion recovery 3D UTE, single adiabatic inversion recovery dual echo 3D UTE with echo subtraction and dual adiabatic inversion recovery 3D UTE. The feasibility of using these approaches was demonstrated in in vitro and in vivo imaging of calcified cartilage, aponeuroses, menisci, tendons, ligaments and cortical bone with a 3-T clinical MR scanner. Signal-to-noise ratios and contrast-to-noise ratios were used to compare the techniques.     

Cu(111)三维表面岛对表面原子扩散影响的分子动力学研究

采用嵌入原子方法的原子间相互作用势，利用分子动力学方法计算了同质外延生长中不同层数的三维Cu(111)表面岛上表面原子扩散激活能，分析了三维表面岛的层数对表面原子交换扩散和跳跃扩散势垒的影响. 研究结果表明，二维Enrilich-Schwoebel(ES)势垒小于三维ES势垒，且三维ES势垒不随表面岛层数的增加而显著变化. 对于侧向表面为(100)的表面岛，表面原子沿〈011〉方向上的扩散行为，随表面岛层数增加而逐渐变化；在表面岛层数达到3层时，扩散路径上的势垒变化趋于稳定，表面原子扩散以下坡扩散为主. 对于侧面取向为(111)的表面岛，当表面岛层数大于3层后，开始呈现上坡扩散的可能. 关键词： 表面原子 扩散 分子动力学模拟     

Evaluation of the inner ear by 3D fast asymmetric spin echo (FASE) MR imaging: phantom and volunteer studies

The 3D fast asymmetric spin echo (FASE) method combines the half-Fourier technique and 3D fast spin echo (FSE) sequence. The advantage of this method is that it maintains the same spatial resolution as FSE while markedly reducing the imaging time. The purpose of the present study was to evaluate the usefulness of the 3D FASE technique in displaying the inner ear structure using phantom and volunteer studies. 3D FSE sequence images were obtained for comparison, and the optimum 3D FASE sequence was investigated on a 1.5T MR scanner. The results of phantom experiments showed increased signal-to-noise ratio (SNR) with prolonging repetition time (TR) on both 3D FASE and 3D FSE sequences. Although the SNR of 3D FASE images was 20-25% lower than that of 3D FSE images with the same TR, the SNR per minute with 3D FASE was about twice that with 3D FSE. On 3D FASE images, a higher spatial resolution was obtained with 2- or 4-shot images than with single-shot images. However, no significant difference was observed between 2-shot and 4-shot images. In the volunteer study, 3D FASE images using a TR of 5000 ms and an effective echo time (TEeff) of 250 ms showed a high SNR and spatial resolution and provided excellent contrast between cerebrospinal fluid and nerves in the internal auditory canal. The highest contrast was achieved in the 2-shot/2 number of excitations sequence. 3D FASE provides the same image quality as 3D FSE with a significant reducing in imaging time, and gives strong T2-weighted images. This method enables detailed visualization of the tiny structures of the inner ear.     

集成成像大纵深物体的三维形貌获取技术

为了满足现代工业所需的大纵深物体的三维形貌获取需求,解决传统结构光三维形貌获取技术纵深较小的问题, 借助集成成像这种阵列式多视点获取技术,构建了基于集成成像的大纵深物体的三维形貌获取技术。从集成成像原理出发,分析了集成成像三维物点和同名像点之间的关系,得到集成成像光学获取系统参数和三维物体纵深极限之间的关系。在此基础上,利用相机和电动平移台构建了扫描式相机集成成像三维形貌获取系统,并对纵深从600 mm到3 600 mm相对独立的2个物体构建的大纵深三维物体进行了形貌获取。光学实验结果显示,该集成成像大纵深物体三维形貌获取技术能够单次获取纵深为3 600 mm的三维物体的三维形貌,为大纵深物体的三维形貌获取提供了技术支持。     

刚体与SPH耦合的三维数值方法研究

 研究了刚性体与SPH（Smoothed Particle Hydrodynamics）方法相耦合的计算方法和技术,以此技术为核心,在原有三维综合拉氏程序CL3D的基础上,研制了适用于斜侵彻问题数值研究的刚性弹体与SPH靶体耦合计算的拉氏三维数值模拟程序CRSPH3D。针对金属材料编入了Johnson-Cook本构模型计算模块,针对混凝土材料编入了Johnson-Holmquist本构模型及与之配套的损伤模型和状态方程等的计算模块。用研制的计算程序对弹体分别正碰和斜碰穿透中厚铝靶和侵彻厚混凝土靶的过程进行了数值模拟计算和分析。结果表明,对于铝靶穿透问题,模拟计算得到的弹体剩余速度、弹体动能损失和贯穿图像与实验结果符合得较好。对于混凝土靶的侵彻问题也得到了与实验现象一致的、定性合理的图像。     

Holovideo: Real-time 3D range video encoding and decoding on GPU

We present a 3D video-encoding technique called Holovideo that is capable of encoding high-resolution 3D videos into standard 2D videos, and then decoding the 2D videos back into 3D rapidly without significant loss of quality. Due to the nature of the algorithm, 2D video compression such as JPEG encoding with QuickTime Run Length Encoding (QTRLE) can be applied with little quality loss, resulting in an effective way to store 3D video at very small file sizes. We found that under a compression ratio of 134:1, Holovideo to OBJ file format, the 3D geometry quality drops at a negligible level. Several sets of 3D videos were captured using a structured light scanner, compressed using the Holovideo codec, and then uncompressed and displayed to demonstrate the effectiveness of the codec. With the use of OpenGL Shaders (GLSL), the 3D video codec can encode and decode in realtime. We demonstrated that for a video size of 512×512, the decoding speed is 28 frames per second (FPS) with a laptop computer using an embedded NVIDIA GeForce 9400 m graphics processing unit (GPU). Encoding can be done with this same setup at 18 FPS, making this technology suitable for applications such as interactive 3D video games and 3D video conferencing.     

Application d'un modéle de l'état liquide à une monocouche de xénon ou de krypton adsorbées sur la surface (0001) du graphite

A phenomenological model of three-dimensional (3D) liquids is applied to a xenon or krypton monolayer adsorbed on (0001) graphite. The rare-gas atoms are assumed to be mobile with a short-range order as in 3D liquids. From the study of the equilibrium 3D gas ? 2D solid and 3D gas ? 2D liquid, one can find with reasonable agreement the pressures and temperatures of the 2D triple point determined experimentally by other authors.     

Three-dimensional polarimetric integral imaging

A three-dimensional (3D) polarimetric image sensing and display technique based on integral imaging is proposed. Three-dimensional polarization distribution of reflected light from a 3D object can be measured as elemental image arrays by a rotating linear polarizer. After the measurement of the polarization of the 3D object, the 3D polarimetric object can be reconstructed optically by displaying the polarization-selected elemental images in spatial light modulators with two quarter-wave plates. Experimental demonstration of 3D polarimetric imaging of a 3D object attached to two orthogonal linear polarizers is presented. To the best of our knowledge, this is the first report on 3D polarimetric sensing imaging and 3D optical reconstruction by integral imaging.     

Photoinduced Intramolecular Charge Transfer in Donor-acceptor Dyad and Donor-bridge-acceptor Triad

在fullerene-PBTDP-TPA三体体系中的光诱导的分子内电荷转移的实验基础上,分别利用密度泛函理论和含时密度泛函理论以及结合二维、三维实空分析方法对fullerene、PBTDP-TPA二体以及fullerene-PBTDP-TPA三体的基态和激发态的性质进行了理论研究．二维定点表象揭示了激发情况下电子和空穴的相干情况．三维跃迁矩阵展示了跃迁偶极矩的方向和强度,而且三维电荷差密度给出了光诱导的分子内电荷转移的方向和结果．同时,用二维和三维表象的方法对fullerene-PBTDP-TPA三体中光诱导的分子内电荷转移过程进行了验证,揭示了在给予者-桥-接收者三体分子体系中分子内激发时电荷转移的机制．除此之外,还发现直接从给予者到接收者超交换的分子内电荷转移极大地促进了给予者-桥-接收者三体分子体系内的电荷转移．     

一种考虑硅通孔电阻-电容效应的三维互连线模型

硅通孔(TSV)是三维集成电路的一种主流技术.基于TSV寄生参数提取模型,对不同物理尺寸的TSV电阻-电容(RC)参数进行提取,采用Q3D仿真结果验证了模型精度.分析TSVRC效应对片上系统的性能及功耗影响,推导了插入缓冲器的三维互连线延时与功耗的解析模型.在45nm互补金属氧化物半导体工艺下,对不同规模的互连电路进行了比较分析.模拟结果显示,TSVRC效应导致互连延时平均增加10%,互连功耗密度平均提高21%;电路规模越小,TSV影响愈加显著.在三维片上系统前端设计中,包含TSV寄生参数的互连模型将有助于设计者更加精确地预测片上互连性能.