花生油存在下胆固醇氧化产物研究

探讨了温度、加热时间、花生油的量对胆固溶氧化的影响情况。用毛细管气相色谱法检出6种胆固溶氧化物。在一定范围内，氧化产物的组成和含量随加热温度升高和加热时间延长明显增加，而随着花生油量增加有明显减小的趋势。     

混合型固相萃取柱净化-气相色谱-质谱法测定婴幼儿配方奶粉中的三聚氰酸

建立了一种混合型固相萃取柱净化-气相色谱-质谱法(GC-MS)测定婴幼儿配方奶粉中三聚氰酸的方法。在84 ℃条件下,用0.5%乙酸水溶液提取样品中的三聚氰酸,离心,滤液经Carb/C18混合型固相萃取柱净化,氮气吹干,硅烷化衍生,GC-MS测定,选择离子监测模式,外标法定量。在0.01～2 mg/L内线性关系良好(r＞0.99),在0.25～2.5 mg/kg的添加水平范围内,平均回收率为80%～103%,相对标准偏差(RSD)为7.7%～14.5%,三聚氰酸的检出限(LOD)为0.10 mg/kg,定量限(LOQ)为0.25 mg/kg。该方法快速、灵敏、准确、专一、耐用,适合婴幼儿配方奶粉中三聚氰酸的确证和定量测定。     

自制双层固相萃取柱在新会陈皮及其制品中11种有机磷农药测定中的应用

以自制改性多壁碳纳米管（MWNTs）和N-丙基乙二胺（PSA）填料分层填装的双层固相萃取柱为净化柱,建立了测定陈皮及其制品中11种有机磷农药残留的分析方法。样品经乙酸乙酯提取、离心后,固相萃取柱净化,净化液经Agilent RTS-1701毛细管柱分离,火焰光度检测器检测,外标法定量。考察了填料类型、填料用量、洗脱方式等因素对提取效率的影响。在优化条件下,11种有机磷农药检测的线性范围为0.020~1.0 mg/L,相关系数为0.9990~0.9998,检出限为3.5~9.6 μ g/kg。样品在10、25、100 μg/kg 3种水平下的加标回收率为50.8%~109%,相对标准偏差为2.7%~8.5%。该法准确度和灵敏度高、操作简单、快速,检出限能满足对有机磷农药残留的限量要求。自制固相萃取柱可降低成本,值得推广应用。     

固相萃取-气相色谱-质谱联用检测地沟油中胆固醇

建立了固相萃取-气相色谱-质谱联用(SPE-GC-MS)检测地沟油样品中胆固醇的分析方法。样品用硅胶固相萃取小柱前处理净化,先用20 mL含0.6%乙醚的正己烷溶液淋洗,再用10 mL含15%乙醚的正己烷溶液洗脱,胆固醇萃取率达97%。净化后的样品用配备电子轰击离子源的气相色谱-质谱联用仪进行测定,以保留时间和特征碎片离子定性,在选择离子监测模式下用外标法定量,选择离子为m/z 213、275、301、368、386,目标离子为m/z 386,参考离子为m/z 213和275。不同加标水平下的加标回收率为91.7%～101%,相对标准偏差(RSD)小于6%,检出限为0.01 mg/L。胆固醇质量浓度在0.24~6.0 mg/L范围内有良好的线性关系(相关系数为0.9996)。该法可精确检测油脂中胆固醇的含量,检测结果可作为判断其中是否掺有地沟油的依据之一。     

血清总磷脂脂肪酸组分的固相萃取-气相色谱法分析

以硅胶基质为固定相,建立了固相萃取-气相色谱(SPE-GC)分离检测血清总磷脂中脂肪酸含量的方法。优化了SPE的洗脱方式及甲醇洗脱量,探讨了衍生化步骤的优化条件。该法对磷脂中各脂肪酸组分测定的线性相关系数约为0.999,回收率在80%左右;日内误差小于4.8%,日间误差小于8.9%。用固相萃取柱分离磷脂简单、快速、有效,用气相色谱检测磷脂中脂肪酸组分方法稳定、可靠。     

无筛板型固相萃取柱的制备及其在食品中苯甲酸的测定研究

结合固相萃取(SPE)盘与含支撑物的SPE柱技术,制备了一种新型的无筛板型固相萃取柱.以C18填料为例,以话梅样品为介质对其中的苯甲酸进行分析,并用传统固相萃取小柱平行比较;将SPE与HPLC-UV结合,考察了填料对简单介质中苯甲酸的最大吸附量及洗脱曲线,研究了新型SPE柱在实际应用中的分离纯化效果.结果表明,新型SPE柱对样品的吸附效果更好,规格为200 mg/3 mL的SPE柱对苯甲酸的吸附量达到0.951 mg,超过了传统柱的吸附量0.908 mg;其洗脱曲线与传统柱几乎重合;苯甲酸在1～100 mg/L浓度范围内线性关系良好, r=0.9999,用此SPE柱纯化后的样品加标回收率和相对误差分别在88.4%～102.3%和1.4%～2.9%之间.     

采用新型固相萃取柱快速测定食用植物油中苯并［a］芘

研究了Bond Elut ENV新型固相萃取柱在食用植物油中苯并[a]芘快速检测中的应用,建立了快速测定食用植物油样品中苯并[a]芘残留量的固相萃取/液相色谱/荧光检测法。样品用正己烷溶解,固相萃取净化,SUPELCOSILTMLC-PAH(25 cm×4.6 mm,5μm)色谱柱分离,以乙腈-水(95∶5)为流动相,荧光检测(λex=297 nm,λem=408 nm),外标法定量。苯并[a]芘的检出限为0.3μg/kg,在1.0～50.0μg/L范围内线性关系良好,相关系数为0.999 6,方法的回收率为79%～102%,相对标准偏差不高于9.4%。该方法准确、实用、简便、快速,在食用植物油的苯并[a]芘残留量检测方面有广泛的应用前景。     

固相萃取–毛细管气相色谱法同时测定水体中8种有机磷类农药残留

建立固相萃取–毛细管气相色谱法同时测定水体中敌敌畏、乙酰甲胺磷、治螟磷、乐果、甲基对硫磷、马拉硫磷、杀螟硫磷和水胺硫磷8种有机磷类农药残留。样品经OASIS HLB固相萃取柱富集,丙酮洗脱,用毛细管气相色谱(FPD)法进行定量分析。8种有机磷类农残留的质量浓度在0.05~4.0μg/m L范围内与色谱峰面积线性关系良好,相关系数均大于0.998,方法检出限为0.004~0.01μg/m L。测定结果的相对偏差为2.6%~4.5%(n=6),加标回收率为81.6%~106.2%。该方法操作简单、灵敏度高,可用于检测水体中的8种有机磷类农药残留。     

固相微萃取的发展近况

固相微萃取（SPME）是一种新型的样品预处理方法，随着对此技术发展的深入理解，新型SPME装置不断得到应用和发展。本文对其原理、装置、应用和发展的现状进行了综述。     

Gas Chromatographic Analysis of Cholesterol Oxidation Products on a Thermostable Medium Polarity Capillary Column

The performance of a fused silica column coated with 50% phenyl-/50% dimethyl-polysiloxane, characterized by a high thermal stability, was evaluated for the gas chromatographic determination of cholesterol oxidation products. A silylated mixture of eighteen oxysterol standards (0.1 mg/ml of each compound) was injected into the gas chromatographic system. The temperature was programmed from 230 to 260°C at 2.5°/min and then to 290°C at 1°/min; the injector and detector temperatures were set at 325°C, and the gas linear velocity was 22.8 cm/s. The column gave a fast (15 min) and satisfactory resolution of the main cholesterol oxides. Good separation of the hydroxy from the epoxy derivatives was achieved.The suitability of the method for the determination of oxysterols in food matrices was successfully tested on a saponified lipid extract from egg yolk powder, previously enriched and purified by NH₂ solid phase extraction.     

紫外光照射下胆固醇氧化产物分析

考察了紫外光照射下胆固醇的氧化情况.实验证明,经过0～5h的紫外光照射,用毛细管气相色谱法检测到有7 酮基胆固醇、5α,6α 环氧胆固醇和胆甾烷三醇生成,其含量随照射时间增加而增加.     

毛细管气相色谱法测定油中植物甾醇和胆固醇

采用2.0mol/L的氢氧化钾乙醇溶液在85℃水浴上皂化45min，石油醚萃取，毛细管气相色谱法分离植物甾醇和胆固醇的分析方法，讨论并确定了样品皂化的最佳条件。用该法测定了芝麻油中甾醇的含量，相对标准偏差为0.86%-4.13%；回收率为89.59%-103.09%。结果表明：采用该方法具有操作快速、简便、准确等优点。     

Comparison of Stir Bar Sorptive Extraction and Solid Phase Extraction as Enrichment Techniques in Combination with Column Liquid Chromatography for the Determination of Polycyclic Aromatic Hydrocarbons in Water Samples

The commonly used solid-phase extraction (SPE) was compared with the recently developed stir bar sorptive extraction (SBSE) to determine EPA-PAHs from precipitation water samples. SPE was performed using C18 PAH-filled cartridges; magnetic stirring rods 10 mm long and coated with 0.5 mm (24 µL) polydimethylsiloxane were used for SBSE. Determination was performed by high performance liquid chromatography and fluorescence detection. The investigations were performed at a concentration level of 30 ng/L, adjusted to actual PAH concentration levels of precipitation water. The recoveries ranged between 54% (SBSE) and 20% (SPE) respectively and about 100%, while the standard deviation ( n = 5) varied in the range of 4.7-13.5% (SBSE) and 3.6-16.9% (SPE) except for the more volatile compounds acenaphthene and fluorene. The detection limits calculated were between 0.4 and 5.0 ng/L. Both techniques were applied to study the PAH contents of precipitation water of several polluted sites in the city of Halle (Saxony-Anhalt, Germany). The advantages and disadvantages of the methods used are discussed.     

Rapid Stability Indicating Uv-Assay of Methenamine Mandelate In Tablets Using Solid Phase Extraction

Abstract

A rapid stability-indicating method was developed to quantitatively determine methenamine mandelate in tablets. After dissolution of the sample in water methenamine is separated from its decomposition product formaldehyde by the use of solid-phase extraction. the determination of methenamine may then be carried out by several procedures. A spectrophotometric assay following hydrolysis of methenamine to formaldehyde appeared to be most suitable.

The simplicity and accuracy of the method compares favourable with the U.S.P. XXI method. the procedure can be advantageously used in stability and quality control studies of methenamine containing dosage forms.

Precision and accuracy were checked by comparing the results of 10 identical raw material samples and 10 tablet samples that were both assayed by this method and the USP XXI procedure (Tables 4 and 5).

The assay values for methenamine and the relative standard deviations were similar for both procedures in both raw material and tablets.

Above results show that the SPE procedures give accurate, precise and reliable values for the methenamine assay. Since no titrant standardizations or lengthly sample pretreatments have to be carried out the method is fast, which makes it very suitable for industrial quality control purposes. the method is also economical. No precious instruments are necessary; a simple colorimetric device is sufficient.

The extraction columns can be reused several times. Even after 10 regenerations the columns did not show any deterioration.     

光离子检测气相色谱法分离分析氨及其氧化产物

本文采用光离子化和热导池两个检测器串联,以5A钙型分子筛填充柱与Chromesorb 104+2％KOH填充柱并联方式,成功地定量分离分析了N2,O2,NO或NO_2,N_2O和NH_3的混合气体。     

Column selection and optimization for sulfur compound analyses by gas chromatography

The analysis of sulfur-containing compounds using fused silica capillary columns and the Sulfur Chemiluminescence Detector has been investigated. This combination of an inert chromatographic system and a high sensitivity, selective detector provides significant advantages for the analysis of low levels of sulfur compounds in complex matrices over existing techniques. Capillary columns coated with thick films (1–4 μm) of methyl silicone stationary phase permit separation of most sulfur containing compounds and, when used with sub-ambient column temperatures, these columns can be used for the separation of sulfur gases. The effects of stationary film thickness, column length, and internal diameter for the measurement of sulfur compounds in hydrocarbon matrices has been determined.     

Application of Graphene as Solid Phase Extraction Absorbent for the Determination of Parabens in Cosmetic Products by Capillary Electrophoresis

A graphene-based solid phase extraction (SPE) technique was developed for the extraction of parabens (methylparaben, ethylparaben, propylparaben, and butylparaben) in cosmetic samples, followed by determination by capillary electrophoresis (CE). The SPE extraction parameters such as eluent reagent and eluent volume, washing solution, sample pH, and flow-rate of sample loading, were investigated for satisfied recoveries. The running buffer, consisting of 25 mM borate solution (pH 10.0), was used for the separation of four parabens with the CE method within 10 min. The limits of detection were 0.14 mg/L, 0.13 mg/L, 0.15 mg/L, and 0.10 mg/L for methylparaben, ethylparaben, propylparaben, and butylparaben, respectively, and the mean recoveries obtained were between 62.6% and 100.4%. The developed method was used for the determination of parabens in real cosmetic products.     

木素碱性硝基苯氧化产物的高效液相色谱分析

- hydroxybenzaldehyde,vanillin and syringaldehyde etc. were separated on a Novapak C18 column (5μ 3. 9mm i. d.× 150mm) and eluted with MeOH-H2O (25:75, V/V) at a flow rate of 0. 6mL/min and detected at 254nm. Quantitative analysis was performed with piperonal instead of synthetic product . m-meconin,as the internal standard. Recoveries are 95%-98% and CV≤1%. The method is simple,rapid and reliable.